Mascot Electric UST-6 Wireless Bodypack Transmitter Microphone User Manual 01

Mascot Electric Co., Ltd. Wireless Bodypack Transmitter Microphone 01

User manual

WIRELESS MICROPHONE SYSTEM
- Connecting the Receiver- Set up channel on receiver y Manual Mode y Auto-Scan Mode y Preset Mode- Set up the handheld microphone / Bodypack transmitter- Synchronizing a transmitter with a receiver- How to set at least 10 sets be used simultaneously- Receiver- Handheld Microphone- Bodypack transmitter- FCC Statement- Safety - Environment- Wireless Notez Product Description.................................................................. 2z Introduction............................................................................. 1z System Operation..................................................................... 6z Basic Connections................................................................... 12z Trouble Shooting...................................................................... 13z Specification............................................................................ 14
WIRELESS INTRODUCTION  FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. zIntroduction Thank you for purchasing our product. This PLL synthesized wireless microphone system operates in UHF band frequency with 700 selectable channels. Please read this instruction manual carefully before operating the system. This manual covers the function and operation of the wireless microphone system.  Safety ¾Do not spill liquid on the appliance and do not drop it on a hard concrete floor. ¾Do not place the equipment near heat sources such as radiators, heating ducts, amplifier, etc.¾If the equipment is not going to be used for a long time, disconnect the AC adapter from the power outlet. Please note that if you turn the equipment off while leaving the AC adapter plugged in, it is not fully isolated from the power supply.¾Do not expose the equipment to direct sunlight, extremely dust, excessive moisture, rain, mechanical vibrations, or shock.¾Take out the battery from transmitter, if the appliance has been not used for a longer period.This will avoid the damage resulting from a defective leaking battery. ¾WARNING: To reduce the risk of fire or electric shock, do not use the products near water and do not expose them to rain or moisture. ¾No guarantee claims for the equipment and no liability for any resulting personal damage or material damage will be accepted if the equipment are used for other purpose than originally intended, if the equipment are not correctly connected or operated, or if the equipment are not repaired in an expert way.  Environment ¾Do not throw used batteries into a fire or garbage bin with domestic rubbish. Be sure to dispose of used batteries in accordance with local waste disposal rules. ¾When disposing the equipment, remove the batteries, separate the case, circuit boards, and cables, and dispose of all components in accordance with local waste disposal rules.1
2Front : LCD Display : 1. Power Button.2. LCD Display: Display channel, frequency and settings.5. GP: Display selected preset group. 6. CH: Display selected preset channel. 8. FREQ.: Display selected frequency. 10. RF Bar: Display the reception status of RF signal. 
3Rear : 1. Antenna2. Balanced XLR Audio Output 3. Unbalanced 6.35mm Audio Output 4. Mic/Line Switch: Use this to adjust audio output level for mic level (-20dB) or line level (0dB).5. Squelch: Turn the switch to adjust or decrease the noise floor level. 6. Mix Out: The audio output for channel 1 and channel 2 are mixed.7. Power Adapter connector7
426451. Power / MUTE Button: Press for 2 seconds to power the microphone on or off. With the transmitter on, a slight press for button will toggle between mute and unmute function. 2 Power / MUTE LED: Indicate the power / mute / low battery level status.3. SYNC Button: Press to active synchronization with the receiver. 4. LCD Display: Display channel number and battery power level. 5. Battery component: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of batteries is correct. 6. Grille: Protects the microphone capsule and helps reduce breath sounds and wind noise.LED Indicator Status Red ReadyFlashing Red Low battery power when less than 10 minutes operationBlue MUTE Flashing Blue MUTE on and low battery power when less than 10 minutes operation
51. Power / MUTE Button: Press for 2 seconds to power the microphone on or off. With the transmitter on, a slight press for button will toggle between mute and unmute function. 2. Power / MUTE LED: Indicate the power / mute / low battery level status. 3. SYNC Button: Press to active synchronization with the receiver 4. LCD Display: Display channel number and battery power level.5. Battery component: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of batteries is correct. 6. Mini XLR Connector: Connect to the lapel microphone or headset microphone. 7. Gain Switch: The switch sets the audio input to 10dB, 0dB, -10dB.LED Indicator Status Red ReadyFlashing Red Low battery power when less than 10 minutes operation Blue MUTE Flashing Blue MUTE on and low battery power when less than 10 minutes operation MIC IN3 : VCC2 : SIGNAL2311 : GNDLINE IN3 : VCC2 : SIGNAL1 : GND
6Connected the provided DC power supply to thereceiver power input with an appropriate ACpower source. The LCD display will light and the receiver is on.¾Using a standard audio cable with 3-pin XLR connectors or 6.3mm phone plugs to connect the mixer or amplifier.¾Set the audio output level for MIC: -20dB LINE: 0dB ¾Using the Volume Controller to adjust the AF audio level to the input of the amplifier or mixer. ¾Never use the balanced and unbalanced audio outputs at the same time! This may cause signal loss or increased noise.zConnecting the receiverPrior to setting up, please check that the transmitter and receiver are tuned to the same frequency or channel. Two or more transmitters operating in the same frequency can not be used at the same time and area.1234AC/DCADAPTERLINE MICUse squelch to avoid reproducing noise when the receiver does not receive enough signal from the transmitter.¾Turn clockwise to increase squelch and reduce noise. When turning the squelch knob clockwise, it begins to eliminate background noise.-When the squelch is all the way to the left, the squelch is off and the ambient RF noise will be easily to receive.-5SYSTEM OPERATION
z Setting up channel on receiver Setting interference-free channel by manual operation.¾7Using the Ɇ button to select the “MANUAL” mode.¾Press “SET” button for 2 seconds till LCD display is flashing.¾Press button Ɇ to change the channel forward.¾Press the “SET” button to lock the setting.¾
Set interference-free channel by automatic frequency scan function.¾8Using the Ɇ button to select the “SCAN” mode.¾Press “SET” button for 2 seconds till LCD display is flashing.¾Press button Ɇ to scan in forward direction, and it will stop at the free-interference channel automatically. ¾Press the “SET” button to lock the setting. ¾
¾Preset ModeSet multiple constructions by using preset channels. There are 4 preset groups. Excluding the interference from external, there are 8 preprogrammed channels can be operated simultaneously in each group.9Using the Ɇ button to select the “PRESET” mode.¾Press channel button Ɇ!to change the programmable group forward. ¾Press the “SET” button to lock the group setting. ¾Press channel button Ɇ to change the programmable channel forward. ¾Press the set button to lock the channel setting.NOTE:When there is any outside interference on the current preset group, please switch to use next preset group. If 4 preset groups are all under interference, please use auto-scan mode or manual mode to set up system.¾Press “SET” button for 2 seconds till LCD display is flashing.¾
Open the battery cover and insert batteries into the battery compartment conforming to the polarity (+)(-) marks.¾ Unscrew the handheld Mic and open the battery cover to insert the battery into the battery compartment and confirm the marks of the polarity (+) (-).¾ Press for 4 seconds to turn the Handheld/ Bodypack transmitter on.¾ If the LED stays flashing , it indicates that the battery will out of power soon and should be changed. zSet up the handheld microphone / bodypack transmitterNOTE: When you don’t use this device for a long term period, please switch the power switch to “off” mode to save more electric power. OPEN67891011 121234567891011 121234510SYSTEM OPERATION Adjust the audio input level. ¾
zSynchronizing a transmitter with a receiverzHow to set at least 10 sets be used simultaneouslyAutomatic frequency synchronization via remote channel for easy setup. Use Auto Scan function to search automatically for the interference free channels.11¾¾¾ Link to transmitter by SYNC (Please refer to above“Sychornizing a transmitter with the receiver” )¾ Repeat above process for setting multiple interference-free channels.¾¾<1MStep 1ORStep 267891011 1212345When using SYNC setting, the distance of receiver and transmitter is within 1 M. Turn on the receiver and using the Ɇ button to select the “SCAN” mode.Press “SET” button for 2 seconds till LCD display is flashing. First, switch the transmitter and the receiver on. Press and hold the SYNC button on your transmitter. The SYNC flashes on the receiver display panel. At the same time, press the SYNC button of the receiver to transfer the selected frequency to the transmitter. Press button Ɇ to scan in forward direction, and it will stop at the free-interference channel automatically.Press the “SET” button to lock the setting.
Antenna holder makes it easy to fix wherever for connection antenna and booster. It can be assembled on the mic stand or on the wall.zBasic ConnectionsTo install a receiver in a 19” standard rack by using 2 short L type metal racks.12BASIC CONNECTIONSL4 The detachable antenna and booster are highly recommended for long-distance purpose, such as in stadium or in auditorium. BNCBNCAntenna BoosterAntenna Antenna
whether is set too high or too low.zTrouble Shooting 13TROUBLE-SHOOTING
Carrier Frequency RangeCaseOscillatorModulationFrequency StabilityS/N ratioImage and Spurious RejectionReceiving SensitivitySelectivityAF ResponseT.H.D.IF FrequencyDynamic RangeTone SignalAudio OutputPower SupplyCurrent ConsumptionDimension (mm)WxHxD: UHF 520.05 - 697.9MHz (FCC): 19" EIA-Rack Metal Case: PLL Synthesized: FM : ±0.005% : ɧ : 80 dB minimum: ɧ50dB: 80Hz to 18KHz : ɦ1% (at 1KHz): 1st: 243.95MHz 2nd:10.7MHz : ɧ100dB : 32.768KHz : Balanced & Unbalanced : 520±10mA: 400×42×18320S(MAX)120mA ± 10mAHandheld: 260 x 52ø Bodypack: 65 x 97 x 24Channel Select: UHF 520.05 - 697.9 MHz (FCC): Synchronizing with the receiver¾ Battery Bodypack : Lavalier Mic / Headset MicLCDMic UnitDisplay32.768KHzTone KeyDimension (mm)WxHxD14440-0200-3

Navigation menu