Masterbuilt ESQ-3040R 40" Electric Smoker with RF User Manual 08102010 20070411 Manual indd

Masterbuilt Manufacturing, Inc. 40" Electric Smoker with RF 08102010 20070411 Manual indd

Users Manual

Masterbuilt Manufacturing, Inc.  1 Masterbuilt Ct.Columbus, GA 31907 Customer Service 1-800-489-1581www.masterbuilt.comManual Code: 9807100002 100810-04JHTool needed for assembly:  Phillips Head ScrewdriverApproximate assembly time : 15 minutesCARBON MONOXIDE HAZARD WARNINGBurning wood chips gives off carbon monoxide, which has no odor and can cause death.  DO NOT burn wood chips inside homes, vehicles, tents, garages or any enclosed areas. Use only outdoors where it is well ventilated.This manual contains important information necessary for the proper and safe use of this unit.Read and follow all warnings and instructions before using smoker and during use.Keep this manual for future reference.Some parts may have sharp edges handle with care.Failure to follow these warnings and instructions properly could result in personal injury or death.ASSEMBLY, CARE & USE MANUALWARNING & SAFETY INFORMATIONELECTRIC SMOKER MODELS 20070211, 20070311, 20070411THIS PRODUCT IS FOR OUTDOOR USE ONLY
1GENERAL WARNINGS AND SAFETY INFORMATION READ ALL INSTRUCTIONS   When using electrical appliances, basic safety precautions should always be followed including    the following: • For outdoor use only.  Do not operate in an enclosed area.• Unit MUST be on the ground.  Do not place unit on tables or counters. Do NOT move unit across uneven surfaces.• Do not lift unit by rear handle. • Do not plug in electric smoker until fully assembled and ready for use. • Use only approved grounded electrical outlet. • Do not use during an electrical storm. • Do not expose electric smoker to rain or water at anytime. • To protect against electrical shock do not immerse cord, plug or control panel in water or other     liquid. • Do not operate any appliance with a damaged cord or plug, or after appliance malfunctions or has     been damaged in any manner.  Contact Masterbuilt Customer Service for assistance at    1-800-489-1581. • Keep a fi re extinguisher accessible at all times while operating electric smoker. • Do not let cord hang touch hot surfaces. • Do not place on or near a hot gas or electric burner, or in a heated oven. • Keep children and pets away from electric smoker at all times.  Do not allow children to use    electric smoker.  Close supervision is necessary should children or pets be in area where electric    smoker is being used. • Fuel, such as charcoal briquettes or heat pellets, are not to be used in electric smoker. • Never use electric smoker as a heater (READ CARBON MONOXIDE HAZARD). • Use electric smoker only on a level, stable surface to prevent tipping. • Electric smoker is HOT while in use and will remain HOT for a period of time afterwards.  Use    caution. • Do not touch HOT surfaces. • Do not allow anyone to conduct activities around electric smoker during or following its use until    the unit has cooled.  Electric smoker is HOT during operation and remains HOT for a period of    time following use. • The use of alcohol, prescription or non-prescription drugs may impair the user’s ability to   properly assemble or safely operate electric smoker.WARNINGS & IMPORTANT SAFEGUARDS CONTINUED ON PAGE 2 18LIMITED WARRANTYMasterbuilt warrants its products to be free from defects in material and workmanship under proper assembly, normal use and recommended care for 90 days from the date of original retail purchase. Masterbuilt warranty does not cover paint fi nish as it may burn off during normal use.Masterbuilt warranty does not cover rust of the unit.Masterbuilt requires reasonable proof of purchase for warranty claims and suggests that you keep your        receipt.  Upon the expiration of such warranty, all such liability shall terminate.Within the stated warranty period, Masterbuilt, at its discretion, shall repair or replace defective components free of charge with owner being responsible for shipping. Should Masterbuilt require return of component(s) in question for inspection Masterbuilt will be responsible for shipping charges to return requested item.This warranty excludes property damage sustained due to misuse, abuse, accident, damage arising out of        transportation, or damage incurred by commercial use of this product.This expressed warranty is the sole warranty given by Masterbuilt and is in lieu of all other warranties,           expressed or implied including implied warranty, merchantability, or fi tness for a particular purpose.Neither Masterbuilt nor the retail establishment selling this product, has authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above. Masterbuilt’s maximum liability, in any event, shall not exceed the purchase price of the product paid by the original consumer/ purchaser. Some states do not allow the exclusion or limitation of incidental or               consequential damages. In such a case, the above limitations or exclusions may not be applicable.California residents only: Not withstanding this limitation of warranty, the following specifi c restrictions       apply; if service, repair, or replacement of the product is not commercially practical, the retailer selling the product or Masterbuilt will refund the purchase price paid for the product, less the amount directlyattributable to use by the original buyer prior to the discovery of the nonconformity. Owner may take the product to the retail establishment selling this product in order to obtain performance under warranty.This expressed warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.Go Online www.masterbuilt.comor complete and return to Attn: Warranty RegistrationMasterbuilt Mfg. Inc.1 Masterbuilt Court - Columbus, GA 31907Name: _________________________________Address :__________________________City:_______________State/Province: ________   Postal Code: ________________Phone Number: (_____) - ____________E-mail Address:_______________________________________Model Number: ____________________       Serial Number:  ____________________ Purchase Date: _____- ______-_______ Place of Purchase: ____________________________________
17This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause      undesired operation.FCC Warning Warning: Changes or modifi cations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC Statement NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that to which the receiver is     connected.4. Consult the dealer or an experienced radio/TV technician for help.GENERAL WARNINGS AND SAFETY INFORMATION • Avoid bumping or impacting electric smoker. • Never move electric smoker when in use.  Allow electric smoker to cool completely before moving    or storing. • Be careful when removing food from electric smoker.  All surfaces are HOT and may cause burns.     Use protective gloves or long, sturdy cooking tools. • Do not cover cooking racks with metal foil.  This will trap heat and cause severe damage to    electric smoker. • Drip tray is only for the bottom of electric smoker.  Do not put drip tray on cooking racks this may    damage electric smoker. • Wood tray is HOT when electric smoker is in use.  Use caution when adding wood. • To disconnect, turn control panel “OFF” then remove plug from outlet. • Unplug from outlet when not in use and before cleaning.  Allow unit to cool completely before   adding/removing grates, tray or water bowl. • Dispose of cold ashes by placing them in aluminum foil, soaking with water and discarding in a    non-combustible container. • Do not store electric smoker with HOT ashes inside unit.  Store only when all surfaces are cold. • Accessory attachments not supplied by Masterbuilt Manufacturing, Inc. are not recommended and     may cause injury. • The use of accessory attachments not recommended by the appliance manufacturer may cause     injuries. • Never use electric smoker for anything other than its intended purpose.  This unit is not for    commer cial use. • Always use electric smoker in accordance with all applicable local, state and federal fi re codes. • Longer extension cords are available and may be used if care is exercised in their use. • If a longer extension cord is used the marked rating should be at least as great as the electrical    rating of the appliance. • The extension cord must be a grounding -type 3-wire cord. • Outdoor extension cords must be used with outdoor use products and are marked with suffi x “W”    and with the statement “Suitable for Use with Outdoor Appliances. • CAUTION - To reduce the risk of electric shock, keep extension cord connection dry and off the    ground. • Extreme caution must be used when moving an appliance containing hot liquids. • Do not clean this product with a water spray or the like. SAVE THESE INSTRUCTIONS2
3LET’S GET STARTED!•  This is a slow smoker…allow suffi cient time for cooking. Smoker is for OUTDOOR USE ONLY.•  “Preseason” smoker prior to fi rst use. See page 11.•  Pre-heat smoker for 30 to 45 minutes at max temperature before loading food.•  DO NOT cover racks with aluminum foil as this will not allow heat to circulate properly. •  Do not overload smoker with food.  Extra large amounts of food may trap heat, extend cooking    time and cause uneven cooking.  Leave space between food on racks and smoker sides to ensure    proper heat circulation. If utilizing cooking pans, place pans on center of rack to ensure even    cooking. Please see manual for more detail.•  Close air damper on top of unit to retain moisture and heat. If cooking foods such as fi sh or jerky,    open air damper to release moisture.•  Temperature reading on control panel will fl uctuate + or - 10 to 15 degrees as smoker cycles on    and off.  •  Store smoker in a dry area after use.•  Extreme cold temperatures may extend cooking times.•  CLEAN AFTER EVERY USE. This will extend the life of your smoker and prevent mold and     mildew.ENJOY!COMBUSTION BY-PRODUCT PRODUCED WHEN USING THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS, OTHER REPRODUCTIVE HARM, OR CANCER.THE MATERIALS USED IN THIS PRODUCT MAY CONTAIN LEAD A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.WARNING16WOOD SMOKING GUIDE FOR MEATS WOOD FLAVOR POULTRY FISH HAM BEEF PORK LAMBHickoryPungent, smoky, bacon-like fl avorMesquiteSweet and delicate fl avorAlderDelicate, wood smoke fl avorPecanBold and hearty fl avorMapleSweet, subtle fl avorAppleSweet, delicate fl avorCherrySweet, delicate fl avorRECIPESSMOKED PORK BUTT7 lbs Fresh pork butt ½ tsp Salt ¼ cup Brown Sugar 2 tbsp Chili Powder Suggested wood chips for smoking:Apple ChipsMix ingredients and rub onto pork butt. Cook pork butt for 5 hours in 225 degree pre heated smoker using apple wood chips during the fi rst 3 hours. After 5 hours remove butt and wrap in heavy foil. Cook for an additional 1 to 1 ½ hours. Internal temperature should be 160 degrees. Serve.SMOKED TUNA4 Tuna Steaks (1” thick) 1 1/8 cup Sugar 3/8 cup Salt 1 tsp Pepper ¼ tsp Garlic (granulated) ¼ tsp Prague powder #1 1 cup Honey 1 gal Water Suggested wood chips for smoking:Hickory or apple chipsMix above ingredients until dissolved in water. Place in pre-heated smoker at 140 degrees and cook for about 7 hours using water mixture in water pan. For more tantalizing recipes and cooking tipsvisit us online at www.masterbuilt.com
•  Maximum temperature setting is 275°F (135°C).•  Do NOT move unit across uneven surfaces.•  Rear handle is NOT for lifting.•  Wood chip loader and wood chip holder MUST be in place when using smoker. This minimizes the    chance of wood fl are ups.•  Wood chips must be used in order to produce smoke and create the smoke fl avor. See “Wood Smoking    Guide for Meats” section in this manual.•  Check grease tray on back of unit often during cooking.  Empty grease tray before it gets full.  Grease     tray may need to be emptied periodically during cooking. •  Do not open smoker door unless necessary.  Opening smoker door causes heat to escape and may    cause wood to fl are up.  Closing the door will re-stabilize the temperature and stop fl are up.•  Do not leave old wood ashes in the wood tray.  Once ashes are cold empty tray. Tray should be cleaned    out prior to and after each use to prevent ash buildup. •  Glass in door is tempered and will not break under normal operation.•  This is a smoker.  There will be a lot of smoke produced when using wood chips. Smoke will escape     through seams and turn the inside of smoker black.  This is normal. To minimize smoke loss around     door, door latch can be adjusted to further tighten door seal against body.15IMPORTANT FACTS ABOUT USING SMOKERFor cooking racks, water bowl and drip tray use a mild dish detergent.  Rinse and dry thoroughly.  For wood chip holder and wood chip loader, clean frequently to remove ash build up, residue and dust. For the interior, glass in door, light cover, meat probe, and exterior of smoker simply wipe down with a damp cloth.  Do not use a cleaning agent.  Make sure to dry thoroughly.Door seal and inside seam that seal attaches to MUST be cleaned after each use to keep seal in proper working condition.ALWAYS MAKE SURE UNIT IS UNPLUGGED AND COOL TO THE TOUCH BEFORE CLEANING AND STORING.HOW TO CLEAN SMOKER•  To adjust door latch, loosen hex nut on door latch. Turn hook    clockwise to tighten as shown. Secure hex nut fi rmly against    door latch.•  Opening smoker door during cooking process may extend cooking    time due to heat loss.•  When outside temperature is cooler than 65°F (18°C) and/or    altitude is above 3,500 feet (1067m), additional cooking time may    be required.  To insure that meat is completely cooked use a    meat thermometer to test internal temperature.4PARTS LISTPART NO QUANTITY DESCRIPTION PART NO QUANTITY DESCRIPTION1 1 Smoker Body 12 1 Drip Pan2 1 Smoker Door 13 4 Smoking Rack3 1 Air Damper 14 1 Door Hinge4 2 Adjustable Screw Leg 15 1 Grease Tray 5 2 Wheels 16 2 Leg Boot 6 1 Digital Control 17 1 Wireless Remote Control7 1 Rear Handle 18 1 Meat Probe8 1 Door Latch 19 1 Light Bulb Cover9 1 Water Bowl 20 1 Element10 1 Wood Chip Holder 21 2 Cooking Grate Support Rack11 1 Wood Chip Loader 22 1 Wood Chip LidSTOP DO NOT RETURN TO RETAILERFor Assembly Assistance, Missing or Damaged PartsCall: MASTERBUILT Customer Service at 1-800-489-1581.18151724567101112931318191420222116
HARDWARE LISTPARTS LISTSTOP DO NOT RETURN TO RETAILERFor Assembly Assistance, Missing or Damaged PartsCall: MASTERBUILT Customer Service at 1-800-489-1581.5 (A)M5*14Phillips ScrewQty: 12Model 20070411PART NO REPLACEMENT PART ITEM NO1 Body Kit 99071000022 Door with Window 99070900283 Air Damper Kit 9900602214 Adjustable Screw Leg 9100500065 Wheel Kit 99071000046 Digital Control Kit 99071000017 Rear Handle Kit 99071000038 Door Latch Kit 9900700189 Water Bowl 91005003010 Wood Chip Holder 900709009211 Wood Chip Loader 900709009312 Drip Pan 91007002813 Smoking Rack 91005002914 Door Hinge Kit 990709004115 Grease Tray 91006004716 Leg Boot 91005000917 Wireless Remote Control 900710000818 Meat Probe 900708000619 Light Bulb Cover Kit 990709003520 Element Kit 990709003321 Cooking Grate Support Rack Kit 99005004922 Wood Chip Lid Kit 990070024Grease Tray Bracket Kit 9900500024Hardware Kit 998050010Instruction Manual 9807100002Models 20070211, 20070311PART NO REPLACEMENT PART ITEM NO1 Body Kit 99071000052 Door with Window 99070900363 Air Damper Kit 9900602214 Adjustable Screw Leg 9100500065 Wheel Kit 99071000046 Digital Control Kit 99071000017 Rear Handle Kit 99071000038 Door Latch Kit 9900700189 Water Bowl 91006006410 Wood Chip Holder 900709009211 Wood Chip Loader 900709009312 Drip Pan 91006006513 Smoking Rack 91006006214 Door Hinge Kit 990709004115 Grease Tray 91006004716 Leg Boot 91005000917 Wireless Remote Control 900710000818 Meat Probe 900708000619 Light Bulb Cover Kit 990709003520 Element Kit 990709003921 Cooking Grate Support Rack Kit 990709003722 Wood Chip Lid Kit 990070024Grease Tray Bracket Kit 9900500024Hardware Kit 998050010Instruction Manual 980710000214TROUBLESHOOTING GUIDESYMPTOMPower light wont comeUnit takes excessive amount of time to heat up  (longer than 60-70 min) There is a gap between the door and the smoker when in use and door latch has no more adjustmentGrease is leaking out of smoker through door and legs No smokeTemperature rapidly decreased, or shut down after few hours of useController displaying error message Power  light  is  on,  unit  isn’t                          heating  Controller does not adjust heatInterior light does not come onMeat probe temperature does not show on displayRemote will not control smokerCAUSENot plugged into wallHouse fuse trippedWire connector on controller not properly connected to smokerController malfunctioningUnit plugged into an extension cordDoor not closed properlyController malfunctioningDoor alignmentDamaged door sealDrip pan not in placeExcess grease or oil build-up in unitDrain tube in back of unit is not drainingNo wood chipsFaulty control unitController malfunctioningController/unit malfunctioningController/unit malfunctioningBulb burned outSwitch is in off positionProbe malfunctioningBatteries are weak or installed wrongRemote is not Linked properly to controllerRemote malfunctioningPOSSIBLE SOLUTIONCheck wall connectionMake sure other appliances are not operating on the same electrical circuit. Check household fuses.See Step 2 on Page 5 Contact Masterbuilt at 1.800.489.1581Set unit so an extension cord does not have to be usedClose door and fasten latch securelyContact Masterbuilt at 1.800.489.1581Contact Masterbuilt at 1.800.489.1581Reposition so hole lines up with drain hole in bottom of unitClean unitCheck drain tube positioning at back of unitAdd wood chips (See Page 11)Contact Masterbuilt at 1.800.489.1581Contact Masterbuilt at 1.800.489.1581Contact Masterbuilt at 1.800.489.1581Contact Masterbuilt at 1.800.489.1581Replace bulb with 15W-25W bulb made for ovensTurn switch onContact Masterbuilt at 1.800.489.1581Refer to page 13 instructionsContact Masterbuilt at 1.800.489.1581
13To replace batteries:• Slide belt clip to the left to remove.• Press tab down on battery cover and pull out.• Install 2 “AAA” Alkaline batteries. Check positive (+) and negative (-) symbols, on the case and   battery, to insure proper installation.• Replace the battery cover.• Remove batteries before storing remote control.To test frequency range:• Turn unit on.• Use remote to turn light on and off as you move away from unit.• Remote control is out of frequency range when light will no longer turn on and off.IMPORTANT• Do not leave remote control exposed to sunlight for prolonged periods of time.• Remote control has frequency range of up to 100ft (30m).• Test frequency range before and during use. TROUBLESHOOTINGIf the remote is not working properly or not interfacing correctly with the controller, it may be due to weak batteries,  batteries being incorrectly installed or the remote is not correctly linked to controller.Possible solutions•  Replace batteries and install according to image in battery housing•  Link remote and controller by: a.  Turn Controller & Remote “ON”, b.  Press and HOLD “SET TEMP” on controller for 3 seconds.c.  On the Remote press “MEAT PROBE”, “LIGHT”, “MEATPROBE”, “LIGHT” (all buttons must be pressed within 5 seconds of each other) A short beep will occur after each button press.  HOW TO USE CONTROL PANEL & REMOTE CONTROLCAUTION  • Keep batteries away from small children. If battery is swallowed consult a physician immediately.  • Be sure to insert batteries correctly.  Improper installation may result in leaks and/or possible explosion.  • Do not dispose of batteries in fi re.  • Do not mix old and new batteries.  • Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh,etc) batteries.*Batteries not included6ASSEMBLY • BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY. • ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE. • TOOL NEEDED: PHILLIPS HEAD SCREWDRIVERSTEP 1Position wheel (5) on bottom of smoker body (1) as shown.Insert adjustable screw leg (4) into bottom of wheel (5).Secure wheel (5) to bottom of smoker body (1) using phillips screws (A).  Repeat step for opposite side.Note: Set adjustable screw leg height by turning clockwise/coun-terclockwise so that smoker is level when unit is upright.  Once level, secure back leg positions with attached tension nuts.STEP 2aPosition control panel (6) on top of smoker body (1) as shown.Align slots on wire connecter from control panel with tabs on wire connecter on smoker as shown and connect together. STEP 2bMount control panel by inserting stabilizing screw head into keyhole.Note: Stabilizing screw may need slight adjustment for snug fi t.16Stabilizing ScrewKeyholeA5A14Tension Nuts
7ASSEMBLYSTEP 3Secure control panel (6) to smoker body (1) with phillips screws (A).Note:  Do not over tighten.STEP 4Attach rear handle (7) to back of smoker body (1) using phillips screws (A) as shown.NOTE: Do not lift unit by rear handle.6AAA1712HOW TO USE CONTROL PANEL & REMOTE CONTROLNote:  Direct sunlight may interfere with ability to read LED display, block light if needed.To set temperature:•Press ON button.•Press SET TEMP button once-LED display will blink.•Use +/- to set temperature.•Press SET TEMP button again to lock in temperature.Note:  Heating will not begin until timer is set.To set timer:•Press SET TIME button once-LED display for hours will blink.•Use +/- to set hours.•Press SET TIME button again to lock in hours.  The minutes LED will start blinking.•Use +/- to set minutes.•Press SET TIME to lock in minutes and start cook cycle.Heat will turn off when time has expired.To use meat probe:• Insert meat probe into center of meat to get most accurate reading. • Press and hold MEAT PROBE button-LED display will show internal temperature of meat. • Once MEAT PROBE  button is released-LED display will return to set temperature or set time.To use light:• Press LIGHT button to turn light on.• Press LIGHT button to turn light off.To RESET control panel:If control panel shows an error message, turn electric smoker off, unplug unit from outlet, waitten seconds, plug unit back into outlet, then turn electric smoker on.  This will reset control panel.
11PRE-SEASON INSTRUCTIONSPreseason smoker prior to fi rst use. Make sure water pan is in place with NO WATER. Set temperature to 275°F (135°C) and run unit for 3 hours. Shut down and allow to cool. Some smoke may appear during this time, this is normal.  During last 45 minutes, add 1 cup of wood chips in chip loader to complete preseasoning.SMOKER IS NOW READY FOR USEHOW TO USE WOOD CHIP LOADERPre-soak wood chips in water for at least 30 minutes. - Applies to models 20070211 and 20070311 ONLY.Before starting unit, place 1 cup of wood chips in chip loader.Never use more than 1 cup of wood chips at a time.  Never use wood chunks.Insert wood chip loader into smoker.  Wood chips should be level with top rim of wood chip loader.Turn handle to “Unload” mark on smoker.  Wood will drop onto wood chip holder.  Turn handle to “Load” and leave wood chip loader in place inside smoker.Check wood chip holder periodically to see if wood has burned down by removing wood chip loader andlooking into smoker through hole.  Add more chips as needed.Wood chip loader must be pulled out completely from smoker when checking wood chip level.ADDING MORE WOOD DURING SMOKING PROCESS:Caution:  Keep smoker door closed when adding wood chips.Note: Wood chip loader will be HOT even if handle is not.To add wood, turn handle to “Load” position on smoker.Pull wood chip loader from smoker.  Place wood chips in wood chip loader and re-insert into smoker.Turn handle to “Unload” mark on smoker.  Wood will drop onto wood chip holder.Temperature may spike briefl y after wood is added.  It will stabilize after a short time. Do not adjust temperature setting.LOADUNLOADCAUTIONWhen door is opened a fl are up may occur.  Should wood chips fl are up, immediately close door, wait for wood chips to burn down then open door again. Do not spray with water. 8ASSEMBLYTHE INFORMATION CONTAINED IN THISSTEP 5Slide cooking racks (13) onto guides inside smoker. STEP 6Place water bowl (9) onto lower bracket inside smoker.Note: Water bowl must always be in place during smoking process, even if there is no water or other liquid in bowl.  Bowl will prevent food from dripping onto wood chip lid.913
9ASSEMBLYSTEP 7Place wood chip holder (10) in smoker as shown.Note: Wood chip holder and wood chip loader MUST be in place when using smoker.  Thisminimizes the chance of fl are ups.STEP 8Place drip pan (12) inside smoker below heating element as shown.  Make sure drip pan hole aligns with hole in bottom of smoker. 101210ASSEMBLYSTEP 9Slide brackets on back of grease tray (15) onto tabs on back of smoker body (1) until grease tray stops.Note: Wheels will not operate while grease tray is in place. Remove grease tray to push/pull smoker.STEP 10Insert wood chip loader (11) into side of smoker as shown.11511

Navigation menu