Masterbuilt Propane Smoker 20051011 Users Manual 20051011_GS40S_IM_041811JH

20051011 to the manual 014a77e0-24d4-45e2-b5e9-4fb7d2b0177b

2015-01-24

: Masterbuilt Masterbuilt-Propane-Smoker-20051011-Users-Manual-342037 masterbuilt-propane-smoker-20051011-users-manual-342037 masterbuilt pdf

Open the PDF directly: View PDF .
Page Count: 11

Download
Open PDF In Browser	View PDF

ASSEMBLY, CARE & USE MANUAL
WARNING & SAFETY INFORMATION

Manual Code: 9805100022 041811-04JH

PROPANE SMOKER MODEL 20051011
THIS PRODUCT IS FOR OUTDOOR USE ONLY

*Actual product may differ from picture shown

Tools needed for assembly: Adjustable Wrench, Phillips Head Screwdriver
CARBON MONOXIDE HAZARD

WARNING

This manual contains important
Burning wood chips gives off carbon
information necessary for the proper assembly
monoxide, which has no odor and can cause death.
and safe use of the appliance.
DO NOT burn wood chips inside homes,
vehicles, tents, garages or any enclosed areas.
Use only outdoors where it is
well ventilated.

Read and follow all warnings and
instructions before assembling and using
the appliance.
Follow all warnings and instructions when
using the appliance.
Keep this manual for future reference.

Failure to follow these warnings and instructions properly could result in fire or explosion, which
could cause property damage, personal injury, or death.

DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open/remove door.
4. If odor continues, keep away from the
appliance and immediately call your
Fire Department.

DANGER

GENERAL WARNINGS AND SAFETY INFORMATION

1. Never operate this appliance unattended.
2. Never operate this appliance within 10 feet
(3m) of any structure, combustible material
or other gas cylinder.
3. Never operate this appliance within 25 feet
(7.5m) of flammable liquids.
4. If fire should occur keep away from appliance
and immediately call your fire department.
Do not attempt to extinguish an oil/grease
fire with water.

• Use 20LB (9kgs) gas cylinder that has protective collar (cylinder not included with unit).
• Installation of unit must conform with local codes or in the absence of local codes, with National
Fuel Gas Code, ANSIZ223.1/NFPA 54, Storage and Handling of Liquefied Petroleum Gasses,
ANSI/NFPA 58 or CSA B149.1, Natural Gas Installation Code; Propane Storage and Handling, CSA
B149.2; or the Standard for Recreational Vehicles, ANSI A119.2/NFPA 1192; and Recreational
Vehicle Code, CSA Z240 RV Series as applicable.
• LP gas cylinder being used must be constructed and marked in accordance with specifications
for LP gas cylinders of the US Department of Transportation (DOT) or the Standard for Cylinders,
Spheres and Tubes for the Transportation for Dangerous Goods, CAN/CSA-B339.
• Always perform soapy water test (see “Soapy Water Test Instructions” in this manual)
EVERY TIME you use unit.
• Before each use check all nuts, screws and bolts to make sure they are tight and secure.
• Before each use inspect gas hose for signs of damage.
• Always disconnect gas cylinder from unit when not in use.
• Never attach/disconnect gas cylinder, move or alter gas fittings when unit is in operation.
• Never use gas cylinder if there is evidence of dents, gouges, bulges, fire damage, erosion,
leakage, excessive rust, or other forms of visible external damage. This may be hazardous and
cylinder should be taken to a liquid propane supplier to be checked.
• Regulator and hose assembly supplied with unit MUST be used. For replacement parts, if
needed, contact Masterbuilt Customer Service at 1-800-489-1581.
• When lighting burner remove all smoker parts to prevent explosion from gas build up.
• If ignition does not take place within five seconds using ignitor button, turn gas control valve to
off position and wait five minutes and repeat lighting procedures.
• Keep fuel supply hose away from unit while in operation.
• Keep fuel supply hose away from any heated surface.
• Do NOT obstruct flow of combustion and ventilation. Keep ventilation openings of cylinder
enclosure free and clear of debris.
• When use is complete, always turn regulator control valve OFF first, then gas cylinder valve OFF.
• Gas MUST be turned off at the supply cylinder when not in use.
• Do NOT store spare LP gas cylinder under or near unit. Gas cylinder safety relief valve may
overheat allowing gas to release causing fire which may cause death or serious injury.
• Never fill cylinder over 80% full or cylinder may release gas causing fire which may cause death
or serious injury.
• If you smell, hear or see gas escaping, immediately get away from gas cylinder and call the Fire
Department. Fire may cause death or serious injury.
• Place a dust cap on cylinder valve outlet whenever cylinder is not in use. Only install dust cap
provided with cylinder. Other caps or plugs may cause leaks.
• Cylinder MUST be stored outdoors, out of children’s reach and must NOT be stored in a building,
garage, or any other enclosed area.
• This appliance is not for frying turkeys.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN FIRE, EXPLOSION OR BURN
HAZARD, WHICH COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

GENERAL WARNINGS AND SAFETY INFORMATION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1

Unit is for outdoor use only.
Never use inside enclosed areas such as patios, garages, buildings or tents.
Never use inside recreational vehicles or on boats.
Never operate unit under overhead construction such as roof coverings, carports, awnings, or
overhangs.
Never use unit as a heater.
Maintain a minimum distance of 10ft (3m) from overhead construction, walls, rails or other
structures.
Keep a minimum 10ft (3m) clearance of all combustible materials such as wood, dry plants,
grass, brush, paper, or canvas.
Keep appliance clear and free from combustible materials such as gasoline and other flammable
vapors and liquids.
Use unit on a level, non-combustible, stable surface such as dirt, concrete, brick or rock.
Keep children and pets away from unit at all times. Do NOT allow children to use unit.
Unit has an open flame. Keep hands, hair, and face away from burner flame. Do NOT lean over
burner when lighting. Loose hair and clothing may catch fire.
Allow unit to cool below 115°F (46°C) before moving or storing.
Avoid bumping or impacting unit.
This unit is HOT while in use and during cooling process. Wear protective gloves/mitts.
Use of alcohol, prescription or non-prescription drugs may impair user’s ability to properly
assemble or safely operate unit.
Never use glass, plastic or ceramic cookware in unit.
Do NOT allow anyone to conduct activities around unit during or following its use until it has
cooled.
Accessory attachments not supplied by Masterbuilt Manufacturing, Inc. are not recommended.
Never use unit for anything other than its intended use. This unit is NOT for commercial use.
Use in accordance with local, state and federal fire codes.

SOAPY WATER TEST WARNINGS & PROCEDURES
WARNINGS
• Soapy Water Test MUST be performed each time gas cylinder is connected to burner/hose or each time it
is used.
• Soapy Water Test MUST be performed outdoors in well ventilated area.
• When performing Soapy Water Test keep smoker away from open flames, sparks or lit cigarettes.
• Smoker is designed to work with propane gas only. Only use gas cylinders marked propane with this unit.
This product will NOT operate with natural gas.
• Never use an open flame to test for gas leaks.
PREPARATION:
• Remove any cookware from smoker.
• Make sure regulator and gas cylinder valve to OFF position.
• Prepare soapy water solution: (1) part dish washing liquid (or more if desired), (3) parts water.
• Apply soapy water solution to gas cylinder valve, regulator and hose length up to burner.

Apply solution to
gas cylinder valve

Apply solution to hose regulator
and the full length of the hose

Apply solution underneath control
panel where burner and hose are
connected

WARNING
PERFORM “SOAPY WATER TEST” BEFORE EACH USE. SEE “SOAPY WATER TEST” SECTION IN
MANUAL. EXTINGUISH ALL OPEN FLAMES BEFORE CONNECTING REGULATOR TO GAS
CYLINDER. TURN GAS OFF AFTER EACH USE.

REGULATOR, BURNER AND GAS VALVE CONNECTION & OPERATION
CLOCKWISE

COUNTER
CLOCKWISE

17.75”
(45cm)

Failed test will present bubbles as
shown below.

APPROX.

12.25” (45cm)
APPROX.

YELLOW
BLUE

(Smoker shown on back for clarity only)

TESTING GAS VALVE:
• Turn gas cylinder valve ON and watch for bubbles. DO NOT LEAVE GAS ON MORE THAN
12 SECONDS. If bubbles appear, stop, turn gas cylinder OFF and retighten fitting. Repeat test.
TESTING REGULATOR AND HOSE:
• AFTER gas cylinder valve has passed Soapy Water Test, turn gas cylinder valve ON, open regulator
control valve one full turn and check for bubbles at valve location, along full length of hose and at burner
connection. DO NOT LEAVE GAS ON MORE THAN 12 SECONDS. If bubbles appear, stop, turn
regulator valve OFF, turn gas cylinder OFF and retighten the connection that is leaking gas. If hose is
source of leak, STOP, do not use unit. Hose must be replaced.
• When test is complete, and there are no leaks, wait minimum of 5 minutes for gas fumes to diminish
before lighting cooker.
DURING ANY PORTION OF SOAPY WATER TEST IF BUBBLES CONTINUE TO
APPEAR, STOP, DO NOT USE UNIT. CONTACT LOCAL PROPANE DEALER OR
MASTERBUILT CUSTOMER SERVICE @ 1-800-489-1581.
Note: Use 20LB (9kgs) gas cylinder that has a protective collar with this unit.
Cylinder NOT included with this unit.

• Inspect hose before each use. If there are signs of wear, cuts, or leaks, replace
unit. DO NOT USE.
• Inspect burner before each use. Check burner and burner ventura tube for
insects and insect nests. A clogged tube can lead to a fire beneath appliance.
• Connect hose regulator to LP Gas Cylinder
1. Make sure gas cylinder valve is closed. Turn knob clockwise until it stops.
2. Make sure control knob on smoker is in the “OFF” position.
3. Remove protective cap from gas cylinder and coupling nut if applicable.
4. Center and insert regulator nipple into valve outlet on gas cylinder as
shown in figure on the left. Turn regulator coupling nut clockwise until it
stops. DO NOT OVER TIGHTEN.
• Perform Soapy Water Test.
• To use turn gas cylinder ON, turn regulator control valve ON, push burner control
knob in and turn counter-clockwise ¼ turn. Push ignitor button to light.
• If ignition does not take place within five seconds, turn gas control valve to off
position and wait five minutes and repeat lighting procedures. If ignition still does
not occur, see match light directions below.
• After use turn burner control knob OFF, turn regulator control valve OFF, then turn
gas cylinder OFF.
• Burner control knob adjusts burner flame. Turn knob counter-clockwise to decrease
flame. Turn knob clockwise SLOWLY to increase flame. Push burner control knob
in and turn clockwise to shut flame off.
• Visually check burner flame. A CORRECT FLAME should be blue with a small
amount of yellow at the tip. An INCORRECT FLAME is excessively yellow and
irregular. If an incorrect flame occurs, turn burner control knob to “OFF position,
turn off regulator and propane tank. Allow unit to cool and then clean burner.
Let burner completely dry before re-lighting.

MATCH LIGHT INSTRUCTIONS
1. Read all instructions and warnings before lighting.
2. Check gas control valve and gas cylinder valve to be certain it is in
OFF position before connecting to gas cylinder. Perform soapy
water test before each use.
3. Open door during lighting.
4. Turn gas control valve on, turn gas cylinder valve on.
5. Place a long, lit fireplace match stick close enough to burner to
ignite.
6. After each use, first turn gas control valve off, then gas cylinder
valve off. Always allow unit to cool completely before touching,
moving or storing.

STOP

DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts
Call: MASTERBUILT Customer Service at 1-800-489-1581.
Please have Model Number and Serial Number available when calling.
These numbers are located on silver label on back of unit.

HARDWARE LIST

PARTS LIST
2

1
21

(A)
M6x12
Phillips Screw
Qty-24

7
12

(B)
#10x3/8
Self-tapping Screw
Qty-4

(D)
Wing Nut
(packed with temperature gauge)
Qty-1

REPLACEMENT PARTS LIST

Model 20051011
9

PART NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26

17
8

5
22

23
15
26

PART NO QUANTITY DESCRIPTION
1
1
Smoker Body
2
1
Smoker Door
3
1
Air Damper
(pre-assembled)
4
2
Rear Legs
5
1
Control Panel
6
1
Burner Box
7
1
Door Handle
8
2
Body Handle
9
1
Flame Disk Bowl
10
11
12
13
5

1
1
4
1

Water Bowl
Water Bowl Holder
Cooking Grate
Temperature Gauge

PART NO QUANTITY DESCRIPTION
14
1
Valve (pre-assembled)
15
1
Ignitor (pre-assembled)
16
1
Control Knob
(pre-assembled)
17
1
Burner (pre-assembled)
18
1
Grease Clip
19
1
Door Latch
20
1
Heat Shield
21
10
Cooking Grate Support
22
1
Matchstick w/Chain
(pre-assembled)
23
1
Regulator/Hose
24
1
Drip Cup
25
1
Right Front Leg
26
1
Left Front Leg

STOP

REPLACEMENT PART
Body Kit
Door with Logo Plate
Air Damper Kit
Rear Leg Kit
Control Panel Kit
Burner Box Kit
Door Handle Kit
Body Handle Kit
Flame Disk Bowl
Water Bowl
Water Bowl Holder
Cooking Grate
Temperature Gauge Kit
Valve Kit
Ignitor Assembly Kit
Control Knob
Burner
Grease Clip
Door Latch Kit
Cooking Grate Support
Match Stick with Chain
Regulator/Hose
Drip Cup
Right Front Leg Kit
Left Front Leg Kit
Hardware Kit
Instruction Manual

ITEM NO
9905100009
9005100052
9904090069
9905100002
9905100011
9905100005
9905090003
9905100003
911060006
9005100017
9005100016
9005100015
9907090034
990060291
990060328
911060014
9005100042
9005100025
990050222
9005100010
908060003
911060001
9005100039
9905100021
9905100020
9905100008
9805100022

ASSEMBLY

ASSEMBLY
STEP 3
Position burner box (6) over center
hole in bottom of smoker body,
carefully aligning venturi over valve
orifice as shown. Attach burner box
to smoker body using phillips
screws (A).

• BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.
• ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE.
• TOOLS NEEDED: ADJUSTABLE WRENCH, PHILLIPS HEAD SCREWDRIVER
A

Carefully position grill as shown.
A

Do not tighten screws all the
way. Leg frames may need to be
adjusted during assembly.

Firmly attach ignition wire to piezo
ignitor on control panel as shown
in Figure B.

STEP 1
Attach rear legs (4), right front leg
(25) and left front leg (26) to bottom of smoker body (1) using phillips screws (A).

26
1

Venturi
Valve Orifice

Do not fully tighten screws yet.

Ignition Wire
Piezo Ignitor
Figure B

STEP 4
Attach heat shield (20) to burner
box (6) using self tapping screws
(B) as shown.

STEP 2
Attach control panel (5) to right
front leg (25) as shown using
phillips screws (A).

Tighten all hardware at this time.
Repeat on opposite side attaching
control panel (5) to left front leg
(26).

B
20

5
B

ASSEMBLY

STEP 7
Insert temperature gauge (13) into
smoker door (2). Secure in place
with wing nut (D).

STEP 5
Mount body handle (8) to smoker
body (1) using phillips screws (A).

2
8

D
13

STEP 6
Insert door handle (7) into smoker
door (2). Secure using phillips
screws (C).

STEP 8
Insert cooking grate supports (21)
into smoker body (1).

7
C
21

ASSEMBLY

ASSEMBLY
STEP 9
Slide cooking grates (12), onto
cooking grate supports (21).

STEP 11
Insert small hook end of grease
clip (18) all of the way up through
large hole in bottom of smoker
body (1), turn grease clip clockwise/counter-clockwise so that it is
supported on small tab.

Position drip cup (24) on grease
clip so it rests snugly.
Drip cup is needed to collect
grease run-off.

Note: Clip may require adjustment
to fit diameter of container.
18

STEP 10
Insert water bowl (10) into water
bowl holder (11) and slide water
bowl holder onto cooking grate
support (21).

STEP 12
Hang matchstick (22) on side of
smoker body (1) as shown.

Place flame disk bowl (9) into
smoker as shown.
21

10
11

ASSEMBLY

TIPS FOR USING WOOD CHIPS
STEP 13
When not in use, hang
regulator/hose (23) on body handle
(8) as shown.

• Pre-soak wood chips in water for at least 30 minutes.
• Before starting unit, place 1-2 cups (0.24l-0.56l) of wood chips in flame disk bowl.
• Never use more than 2 cups (0.56l) of wood chips at a time. Never use wood chunks.
• Check flame disk bowl periodically to see if wood has burned down. Add more chips as needed.

23
8

WOOD SMOKING GUIDE FOR MEATS
PRE-SEASON INSTRUCTIONS
WOOD FLAVOR
Curing your smoker will rid the unit of chemicals and oils left over by the manufacturing process
allowing them to burn off. Preseason smoker prior to first use.
1. Perform soapy water test (see pg. 3).
2. Using a napkin or cloth, rub a light coat of cooking oil on cooking grates and inside smoker door.
Make sure water pan is in place with NO WATER.
3. Fill flame disk bowl with 1-2 cups (0.24l-0.56l) wood chips and light smoker. Close door.
4. Let the smoker burn for about 30 minutes. Make sure temperature gets up to 400°F (204°C).
5. Allow unit to cool completely.
6. Reapply light coat of cooking oil on the grilling surface and inside of smoker door.
7. Relight smoker and burn the oil for 20 minutes.
• Cure your smoker periodically to prevent excessive rust.

POULTRY

FISH

HAM

BEEF

PORK

LAMB

Hickory
Pungent, smoky, bacon-like flavor

Mesquite
Sweet and delicate flavor

Alder
Delicate, wood smoke flavor

Pecan
Bold and hearty flavor

Maple
Sweet, subtle flavor

Apple
Sweet, delicate flavor

Cherry
Sweet, delicate flavor

SMOKER IS READY FOR USE
13

SMOKING CHART

WARNING
COMBUSTION BY-PRODUCT PRODUCED WHEN USING THIS PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS,
OTHER REPRODUCTIVE HARM, OR CANCER.
THE MATERIALS USED IN THIS PRODUCT MAY CONTAIN LEAD A CHEMICAL KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.

ITEM

SIZE

TEMP

WOOD CHIPS

COOK TIME

INTERNAL TEMP

BEEF
Pot Roast (arm,
top, chuck, blade)

4 - 5 lbs
(1.8-2.3kgs)

225°F
(107°C)

2 cups
(0.47l)

3 - 5 hrs

140°F (60°C) Rare 160°F (71°C) Med
170°F (77°C) Well

Brisket

6-10lbs
(2.7-4.5kgs)

225°F
(107°C)

3 cups
(0.83l)

6-8 hrs

170°F (77°C)
Well Done

PORK

SAFE STORAGE & MAINTENANCE

Loin Roast
(bone in)

4-5lbs
(1.8-2.3kgs)

225°F
(107°C)

2 cups
(0.56l)

5 hrs
165°F (74°C)
Well Done

• ALWAYS allow unit to cool completely before handling.
• Inspect all hardware in assembled parts for tightness on a regular basis to insure unit is in safe working
condition.
• Clean unit, including special surfaces such as cooking grates with mild cleaning agents. Wipe outside of
unit with damp rag. DO NOT use oven cleaner.

Loin Roast
(boneless)

3 - 5 lbs
(1.4-2.3kgs)

Spare Ribs

4 - 6 lbs
(1.8-2.7kgs)

Chicken
(2 whole)

2 - 3 lbs ea
(0.9-1.4kgs)

Turkey

11 - 14 lbs
(5.0-6.4kgs)

225°F
(107°C)

1 cup
(0.24l)

225°F
(107°C)

2 cups
(0.56l)

• NEVER USE PAINT ON INSIDE SURFACES OF UNIT.

3 - 4.5 hrs

165°F (74°C)
Well Done
165°F (74°C)
Well Done

POULTRY

• ALWAYS cover and store cold unit in a protected area.
• Unit is made of steel and may rust over time. If rusting occurs on outside surfaces, clean area with sand
paper or steel wool, then cover with heat resistant paint.

2.5 - 4 hrs

225°F
(107°C)
225°F
(107°C)

1 cup
(0.24l)

2 cups
(0.83l)

2.5 - 3.5 hrs

6 - 7.5 hrs

165°F (74°C)
Well Done
165°F (74°C)
Well Done

SEAFOOD

HOW TO CLEAN SMOKER
For cooking grates, water bowl and drip cup use a mild dish detergent. Rinse and dry thoroughly.

Salmon
Steaks

2 - 4 lbs ea
(0.9-1.8kgs)

225°F
(107°C)

1 cup
(0.24l)

1 - 2 hrs

145°F (63°C)

Fish Fillets

2 - 4 lbs ea
(0.9-1.8kgs)

225°F
(107°C)

1 cup
(0.24l)

1 - 2 hrs

145°F (63°C)

Shrimp, Clams,
Crab Legs

5 lbs
(2.3kgs)

225°F
(107°C)

1 cup
(0.24l)

1 - 2 hrs

145°F (63°C)

For flame disk bowl, clean frequently to remove ash build up, residue and dust.
For the interior and exterior of smoker, simply wipe down with a damp cloth. Do not use a cleaning agent.
Make sure to dry thoroughly.

WILD GAME
Quail,
Dove, etc.

12 - 16 birds

225°F
(107°C)

1 cup
(0.24l)

1.5 - 2.5 hrs

Pheasant, Duck,
etc.

5 - 7 lbs
(2.3-3.2kgs)

225°F
(107°C)

1 cup
(0.24l)

2.5 - 3.5 hrs

165°F (74°C)
165°F (74°C)

ALWAYS MAKE SURE UNIT IS COOL
TO THE TOUCH BEFORE CLEANING AND STORING.

• When outside temperature is cooler than 65°F (18°C) and/or altitude is above 3,500 feet (1067m),
additional cooking time may be required. To insure that meat is completely cooked use a meat
thermometer to test internal temperature.
• Opening smoker door during cooking process may extend cooking time due to heat loss.

RECIPES

LIMITED WARRANTY
HONEY CURED SMOKED SALMON

PORK OR BABY BACK RIBS
2-4 lbs Pork or Baby Back Ribs

1 qt Water

½ tbsp Salt

¼ cup Brown Sugar

¾ cup Honey

2 ½ tbsp Chili Powder

¼ cup Golden Rum

1 ½ tbsp Ground Cumin

¼ cup Lemon Juice

2 tsp Cayenne Pepper

10 Cloves

2 tsp Black Pepper (freshly ground)

10 Allspice Berries

2 tsp Garlic Powder

1 Bay Leaf

2 tsp Onion Powder

1 Large Fillet of Salmon

Hickory Chips

Hickory or Apple Chips

Mix ingredients and rub mixture on meat for 2 hours
before cooking. Allow meat to reach room temperature.

Combine all of the ingredients except salmon to make a
brine. Place the salmon, skin side up, in a baking dish
and cover with brining liquid. Allow fish to brine for two
hours. Rinse salmon in cold water and pat dry.

Cook ribs for 3 hours at 225°F (107°C) in preheated
smoker using hickory chips during the first 2 hours.
After 3 hours remove the ribs and wrap in heavy foil.
Cook for an additional 1- 1 ½ hours until internal
temperature reaches 160°F (71°C).

MAPLE GLAZED HAM

SMOKED CORNISH HEN & WILD RICE

5-7 lbs Ham Shank or Butt (Fully cooked, bone in)

2 Cornish Game Hens

1 ½ cup Maple Syrup

¼ cup Green Onion (chopped)

1 tsp Ginger

3 tbsp Butter

¼ tsp Nutmeg

1 cup Wild Rice (cooked)

½ tsp Allspice

¼ cup Pecans or Walnuts (chopped)

16 Whole Cloves

½ cup Lime Marmalade

1 Can Pineapple Slices (canned)

¼ cup Orange Juice

1 Jar Maraschino Cherries
Hickory or Mesquite Chips
Remove thick skin and trim fat leaving no more than
½” thick covering on ham. Score ham. Combine syrup,
ginger, nutmeg, and allspice in a small bowl. Place ham
in large dish and baste with syrup mixture. Let ham stand
in syrup mixture for 1 or 2 hours basting frequently until
at room temperature.
When ready to smoke remove ham from dish and stud
with cloves. Place ham in preheated 225°F (107°C)
smoker. Cook for about 2-3 hours. Baste with syrup
mixture at least 2 times during cooking time. Before last
hour of smoking decorate ham with canned pineapple
and cherries and baste. Internal temperature of ham
should be at 160°F (71°C) when heated.

Place salmon on a drying rack (or grill rack that you
will use to smoke the salmon on) and allow to air dry
for at least 1 hour. Smoke the salmon skin side down
for about 1-1 ½ hours at 225°F (107°C) and internal
temperature reaches 145°F (63°C).

Salt

Masterbuilt warrants its products to be free from defects in material and workmanship under proper
assembly, normal use and recommended care for 90 days from the date of original retail purchase.
Masterbuilt warranty does not cover paint finish as it may burn off during normal use.
Masterbuilt warranty does not cover rust of the unit.
Masterbuilt requires reasonable proof of purchase for warranty claims and suggests that you keep your
receipt. Upon the expiration of such warranty, all such liability shall terminate.
Within the stated warranty period, Masterbuilt, at its discretion, shall repair or replace defective components
free of charge with owner being responsible for shipping. Should Masterbuilt require return of component(s)
in question for inspection Masterbuilt will be responsible for shipping charges to return requested item.
This warranty excludes property damage sustained due to misuse, abuse, accident, damage arising out of
transportation, or damage incurred by commercial use of this product.
This expressed warranty is the sole warranty given by Masterbuilt and is in lieu of all other warranties,
expressed or implied including implied warranty, merchantability, or fitness for a particular purpose.
Neither Masterbuilt nor the retail establishment selling this product, has authority to make any warranties or
to promise remedies in addition to or inconsistent with those stated above.
Masterbuilt’s maximum liability, in any event, shall not exceed the purchase price of the product paid by
the original consumer/ purchaser. Some states do not allow the exclusion or limitation of incidental or
consequential damages. In such a case, the above limitations or exclusions may not be applicable.
California residents only: Not withstanding this limitation of warranty, the following specific restrictions
apply; if service, repair, or replacement of the product is not commercially practical, the retailer selling the
product or Masterbuilt will refund the purchase price paid for the product, less the amount directly
attributable to use by the original buyer prior to the discovery of the nonconformity. Owner may take the
product to the retail establishment selling this product in order to obtain performance under warranty.
This expressed warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.

Go Online www.masterbuilt.com
or complete and return to
Attn: Warranty Registration
Masterbuilt Mfg. Inc.
1 Masterbuilt Court - Columbus, GA 31907

Name: __________________________________ Address :___________________________ City:________________

Hickory Chips
State/Province: ________ Postal Code: ________________Phone Number: (_____) - ____________
Rinse and pat dry each hen. Season cavities with salt.
Sautee onions in 1 tbsp butter. Stir in rice and chopped
nuts.

E-mail Address:_______________________________________
*Model Number: ____________________

Stuff hens with rice mixture. Close with skewers or
kitchen string. Melt remaining 2 tbsp of butter in small
saucepan. Add marmalade and orange juice blending
until smooth. Brush hens with marmalade mixture.

*Serial Number: ____________________

Purchase Date: _____- ______-_______ Place of Purchase: ____________________________________
*Model Number and Serial Number are located on silver label on back of unit.

Place hens on grate in 225°F (107°C) pre-heated
smoker and cook for 2-2 ½ hours until internal
temperature reaches 165°F (74°C) . Brush with
remaining glaze before serving.

Masterbuilt Manufacturing, Inc.
1 Masterbuilt Ct.
Columbus, GA 31907
Customer Service 1-800-489-1581
www.masterbuilt.com

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jhenderson
Create Date                     : 2011:09:02 14:58:02-04:00
Modify Date                     : 2011:09:02 14:58:02-04:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : jhenderson
Title                           : 20051011_GS40S_IM_041811JH.indd
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.4.2 (Windows)
Document ID                     : uuid:a8ddbfb7-eee4-4412-bc9e-83c23b30b1f1
Instance ID                     : uuid:cb79e035-4a4b-467b-9ab2-691cfb05b2a7
Page Count                      : 11

EXIF Metadata provided by EXIF.tools

Masterbuilt Propane Smoker 20051011 Users Manual 20051011_GS40S_IM_041811JH

20051011 to the manual 014a77e0-24d4-45e2-b5e9-4fb7d2b0177b

Navigation menu

Versions of this User Manual:

Views

Navigation