Matsunichi Communication R and D GP430 GPS User Manual GP430 FCC

Matsunichi Communication Holdings R&D; (Shenzhen) Co., Ltd. GPS GP430 FCC

Users Manual

www.matsunichi.com.cn12356781094 感谢您购买本公司的产品，在使用本产品前，请认真阅读本说明书。1.基本按键介绍2.功能说明3.充电器的使用① 开机键② 拍照键③ Mini-SD插口④ Mini-USB接口⑤ 指示灯⑥ 声音控制键⑦ 3.5mm耳机接口⑧ 摄像头⑨ 电池盖⑩ GPS支架2.1 开机/关机 开机：在关机状态下，按住电源开关3~5秒即可开机，开机时会显示松日LOGO。如下图：2.2 系统主界面 开机后，在系统主界面下，点击屏幕下方的小图标即可切换到该功能的页面，点击右下角的箭头图标可以翻页查看，翻页时屏幕中间会有动画效果。2.3 二级界面-系统设置 在此界面下，点击屏幕上的图标即可进入对应的功能，点击右下角的箭头图标可以翻页查看，翻页时会有动画效果。3.1 USB充电器 先将充电器插入220V的交流电插座，再将另外一头插入本机USB插口3.2 汽车充电器 先将汽车充电器的一头插入点烟器插孔内，再将另外一头插入本机的USB插口（如下图）。 休眠/关机：在开机状态下，按住电源键3~5秒，屏幕会出现休眠/关机确认画面，如下图： 在此界面下，点击 按键可进入休眠状态，点击 按键可关机，点击 按键退出此界面返回到正常操作状态。休眠唤醒：在休眠状态下，按一下机身上的电源键可退出休眠界面返回到正常操作状态。序号 故 障 原因分析 解决办法123无法开机死 机无法充电1.电池电量耗尽（按电源键时，屏幕没有显示）。 请使用充电器为本机充电。2.在启动界面出现后，长时间停止不动。 取出电池，然后再次装入电池后正常开机使用 取出电池，然后再次装入电池后正常开机使用 屏幕不显示，或者有显示但显示不变且按任何键无效。在充电时，本机的绿色指示灯没有亮或屏幕没有显示充电符号。1.充电器是否插入正确或通电。2.充电器损坏。3.电池损坏或电池已充满电。4.简单故障排除123567810941. Key Introduction2. Function Introduction① Power On/Off② Camera Key③ Mini-SD Jack④ Mini-USB Jack⑤ Indicator ⑥ Volume Control Button⑦ 3.5mm Earphone Jack⑧ Camera⑨ Battery Cap⑩ GPS Stand2.1 Power On/OffPower On: In power off status, press the power button for 3~5 seconds to turn on the device, then the "NATIONAL GEOGRAPHIC" LOGO will be displayed on screen.Sleeping&Power Off: In power-on mode, press the power button on the device for 3~5 seconds then the sleeping mode or confirmation for power-off screen will display as follows:THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSEDBY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONSCOULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received,including interference that may cause undesired operation.Waking-up from the sleeping: When in sleeping mode, a short press on the power-on button of the device will wake up the system.When in sleeping mode, all the procedure in operation will pause but will back to normal status after waking up.In this UI click the button will be in sleeping mode, click the button will power off; click the button to exit the UI and back to normal operation.Thanks for purchasing our product. Please read this manual carefully before starting to use this device. 20The clevice will be power off in s2.2 System UIAfter power on, under this UI, click icon on the left screen to enter the function page. 3. Charger Application 4. Trouble Shooter2.3 Secondary UI(Customized)Under this UI, click the button on screen to enter the function page.3.1 USB ChargerTake out the USB charger, plug it into the wall outlet with AC 220V (100V~240V), then plug USB line into the USB jack.3.2 Car Lighter ChargerPlease insert the car charger into car cigarette lighter jack, then plug into the USB jack(see the illustration below).No. Fault Possible Cause Solutions123No power onDead UnitBattery drained (The screen has no further display after a blink when pressing power on button.)Please refer to the description of battery charging in this manual, only use the enclosed charger to charge the device.No display of the screen, or display on screen is frozen as any button is pressed.Take out the battery, then put it back, start the device again.Impossible to rechargeDuring charging, the green LED indicator of the device has no light or no charging sign displayed on the screen.If the charger is connected properly and powered.Charger is damaged.Battery is damaged or full charged.软体：审核：GP430简易中文说明书Simple User Manual封面封面１ ２３４FCC NOTE:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Navigation menu