Mattel Asia Pacific Sourcing C4639-04A4R Batman RC Receiver User Manual C4639 0920 1L IS

Mattel asia Pacific Sourcing Ltd. Batman RC Receiver C4639 0920 1L IS

users manual

Download: Mattel Asia Pacific Sourcing C4639-04A4R Batman RC Receiver User Manual C4639 0920   1L IS
Mirror Download [FCC.gov]Mattel Asia Pacific Sourcing C4639-04A4R Batman RC Receiver User Manual C4639 0920   1L IS
Document ID497312
Application IDv4/0vGCDZ9oOARdsVJWmeA==
Document Descriptionusers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize18.31kB (228853 bits)
Date Submitted2004-12-16 00:00:00
Date Available2004-12-14 00:00:00
Creation Date2004-11-29 14:28:31
Producing SoftwareAcrobat Distiller 5.0.5 for Macintosh
Document Lastmod2004-11-29 14:28:31
Document TitleC4639-0920 1L IS
Document CreatorQuarkXPressª: AdobePS 8.7.2 (104)

C4639-0920
CAUTION-ELECTRIC TOY:
NOT RECOMMENDED
FOR CHILDREN UNDER
8 YEARS OF AGE. AS WITH ALL ELECTRIC PRODUCTS,PRECAUTIONS SHOULD BE
OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK.
INPUT: 120VAC, 60Hz, 12VA. OUTPUT: 8.5VDC, 420mA, 3.6W.
®
TYCO R/C SUPPORT
7.2V R/C
CAUTION: Surfaces may become hot and cause burns if
electronics get wet. Do not operate vehicle through water or snow.
CONTENTS/FEATURES
Questions or problems with your product?
DON’T RETURN IT TO THE STORE!
Just call us for help.
U.S. consumers may also register their products at this number.
1 888 557-TYCO (8926)
tycorc.com
Keep these instructions for future reference: they contain important information.
IMPORTANT: Please read all “Consumer Information” (last page) before operating your vehicle.
t MultiBand™ Selector Switch
Vehicle
q Steering Adjuster
Vehicle
Transmitter
7.2V Battery Pack
7.2V Wall Charger
with a screwdriver (not included)
* Turn
to keep vehicle running straight.
see the “MultiBand™ Feature”
* Please
Section for more information.
Transmitter
w Battery Door
e Battery Latch
r ON/OFF/SOUND Switch
q Vehicle Controls
w Antenna
e MultiBand™ Selector Switch
* This switch has 3 positions:
see the “MultiBand™ Feature”
* Please
Section for more information.
= Vehicle ON (cool engine sounds). In
this position, your vehicle will run
with cool “revving” engine sound
effects as you drive.
= Vehicle OFF
= Vehicle ON (no sounds). In this
position, your vehicle will run with
engine sound effects off.
VEHICLE OPERATION
FORWARD
REVERSE
LEFT
RIGHT
2 1
MULTIBAND™ FEATURE
BATTERY INSTALLATION
• Your vehicle features the advanced Tyco® R/C MultiBand™
system. This system lets you race your vehicle head-to-head
– against up to two of your friends (up to 3 drivers total) –
without any radio interference from your friends’ transmiters
or vehicles. You must be racing against another Tyco® R/C
MultiBand™-equipped vehicle for this feature to work.
• There’s one MultiBand™ Selector Switch on your vehicle
chassis, and another one on your transmitter. The vehicle
switch has 3 positions: one for each MultiBand™ setting.
For detailed information regarding rechargeable battery
charging and safety, please refer to the “Battery
Charging/Care” Section.
The transmitter switch has 3 positions: one for each
MultiBand™ setting.
• For successful operation, the vehicle switch and the
transmitter switch must be set to the same MultiBand™
setting. When you’re driving by yourself, you can set the
switches to any of the 3 MultiBand™ settings (as long as
they match).
• When you want to race head-to-head, just make sure that
each driver (up to 3 drivers total) has a vehicle and
transmitter set to a different MultiBand™ setting.
Vehicle
1. Rotate the battery door latch to unlocked position and
open the battery door.
2. Insert the charged battery pack into the battery
compartment as shown.
3. Connect the battery pack’s wire connector to the vehicle’s
charging jack as shown. Make certain the connector is
securely connected.
4. Close the battery door and rotate the battery door latch to
locked position.
7.2V d.c.
* The transmitter’s MultiBand™ Selector Switch also serves
as the transmitter’s power switch. To operate your
vehicle, just turn the vehicle ON; then set the transmitter
switch to the desired MultiBand™ setting. Push any
transmitter control and you will be able to run and control
your vehicle.
* You must be racing against another Tyco® R/C
MultiBand™-equipped vehicle for this feature to work. A
non-MultiBand™ vehicle, running on the same frequency
as your vehicle, may interfere with operation of your
vehicle. If you are racing against a non-MultiBand™
vehicle, make sure that vehicle operates on a frequency
different from yours.
* If you need to change the MultiBand™ setting, first make
sure that your vehicle is turned OFF. Change the switch
position as desired, making sure to change both the
transmitter AND the vehicle switches. Then turn your
vehicle back ON for more racing action. NOTE: Make
certain you’re not pressing a transmitter control while
changing selector switch position.
Transmitter
1. To install transmitter battery, open battery cover as shown.
2. Install 2 AA alkaline batteries with polarity (-/+) as shown
inside battery compartment.
3. Replace battery cover.
2 1
BATTERY CHARGING/CARE
CAUTION: Use only the charger
supplied with this toy. Do not use
any other charging source.
Use only Tyco® R/C 7.2V NiCd battery
packs. Other batteries may leak or
rupture, causing personal injury and
damage.
1. Plug wall pack charger into standard
wall outlet.
2. Connect the battery pack’s wire
connector to the wall pack charger
connector. Make certain the two
connectors are tightly snapped
together.
3. To disconnect wires, push down on the
connector clip and pull apart.
4. After charging, the battery will feel
warm. This condition is normal for fully
charged batteries.
5. New battery packs must be charged for
5 1/2 hours the first two times charged.
Subsequent charges will require 4
hours. Charging the battery pack for
more than 5 1/2 hours will not give you a
longer running time. 5 1/2 hours is all
that is required for a fully charged
battery pack.
6. Unlike alkaline batteries, which lose
power gradually, a NiCd (NickelCadmium) battery will run for its normal
running time and then lose most of its
power at once. It is time to recharge the
battery pack.
7. After use, the battery pack will be hot!
Wait at least 20 minutes until the battery
pack cools before recharging.
Recharging a warm or hot battery pack
will greatly reduce the number of times
your battery pack can be recharged.
RECHARGEABLE BATTERY INFORMATION:
Note to Adults:
 DO NOT RECHARGE BATTERY PACK IF
IT’S HOT. ALLOW IT TO COOL BEFORE
RECHARGING.
 DO NOT RECHARGE A BATTERY PACK
THAT SHOWS LEAKAGE OR
CORROSION.
 DO NOT DISASSEMBLE THE BATTERY
PACK. THE BATTERY PACK IS A
SEALED RECHARGEABLE NICKELCADMIUM BATTERY.
 EXERCISE CAUTION IN HANDLING A
HOT BATTERY PACK.
 IF BATTERY PACK AND/OR CHARGER
ARE WET, THOROUGHLY DRY BEFORE
CHARGING.
 DO NOT RECHARGE NONRECHARGEABLE BATTERIES.
• Remove rechargeable batteries before
recharging. Recharge batteries only
under adult supervision.
• Regularly examine for damage to the
cord, plug, enclosure and other parts.
In the event of any damage, the toy must
not be used with the battery charger
until the damage has been repaired.
• This toy is not intended for children
under 3 years old. The battery charger
is not a toy.
THIS PRODUCT USES A NICKELCADMIUM RECHARGEABLE BATTERY
PACK. BATTERY MUST BE RECYCLED OR
DISPOSED OF PROPERLY. FOR FURTHER
INFORMATION REGARDING BATTERIES
OR THEIR DISPOSAL PLEASE CALL
1-888-557-TYCO.
THIS PRODUCT USES A NICKEL-CADMIUM RECHARGEABLE BATTERY PACK. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
FOR FURTHER INFORMATION REGARDING BATTERIES OR THEIR DISPOSAL PLEASE CALL 1-888-557-TYCO.
CONSUMER INFORMATION:
QUICK TIPS
q When your vehicle starts to
w Your vehicle's running time may e Radio interference can make r Point your transmitter antenna t Don’t drive your vehicle in sand y Don’t store your vehicle near
lose power, it may lose
change depending on your
your vehicle run badly.
up - not down toward your
or through water or snow. If
heat or in direct sunlight.
functions or performance.
driving style.
Interference can be caused by
vehicle. If your vehicle gets too
your vehicle does get wet, wipe Always turn switches OFF and
It's time for a recharge. For best
other non-MultiBand™ R/C
far away, it won't work properly. with a towel and allow to dry
remove all batteries for storage.
performance, always start with
vehicles running on the same
completely.
a fully-charged battery.
frequency; electrical wires;
large buildings; CB radios; or
other wireless gear. Try to stay
away from these!
Note to Adults: To ensure that the child’s play is
both safe and fun, please review all operating
instructions and safety rules with your child..
Safety Tips
• NEVER drive your vehicle on streets! They’re for
real cars!
• DO NOT pick up vehicle while in motion.
• Keep fingers, hair and loose clothing away from
the tires and the wheel hubs while the vehicle is
switched ON.
To prevent entanglement, keep
X CAUTION:
hair away from wheels.
• Adult supervision is recommended when this
vehicle is being operated.
• To avoid accidental operation, remove all
batteries when not in use. Always turn all
switches OFF before removing batteries.
• Exhausted batteries are to be removed from the
toy.
• The supply terminals are not to be short-circuited.
In exceptional circumstances batteries may leak
fluids that can cause a chemical burn injury or ruin • Dispose of battery(ies) safely.
• Do not dispose of this toy in a fire. The batteries
your toy (product). To avoid battery leakage:
inside may explode or leak.
• Non-rechargeable batteries are not to be
Battery Performance Note:
recharged.
• Rechargeable batteries are to be removed from For best performance use regular or high-performance alkaline batteries (where disposable batteries
the toy before being charged (if designed to be
are called for). If your vehicle is supplied with
removable).
standard (carbon-zinc) batteries for initial use and/or
• Rechargeable batteries are only to be charged
demonstration purposes, we recommend replacing
under adult supervision (if designed to be
them with alkaline batteries when necessary. Battery
removable).
life may vary depending on battery brand.
• Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as
recommended are to be used.
• Batteries are to be inserted with the correct
polarity.
BATTERY SAFETY INFORMATION
TROUBLESHOOTING - PROBLEM? - SOLUTIONS
SYMPTOM
• PROBABLE CAUSE
• CORRECTION
Vehicle runs slowly or will not run.
• Loose battery connection or vehicle switch not ON.
• Weak or uncharged rechargeable battery.
• Weak transmitter battery.
• Transmitter and vehicle MultiBand™ Selector Switches
set to different MultiBand™ settings.
• Check battery connector and vehicle switch.
• Charge battery or replace.
• Replace with fresh alkaline battery.
• Check MultiBand™ Selector Switches and change switch
positions if necessary (MultiBand™ settings must match).
Erratic operation or only short range possible.
• Radio interference likely.
• Check for possible interference, and change driving
location if necessary (see point 2 – Quick Tips).
Short rechargeable battery life.
• Battery not fully charged.
• Recharge vehicle battery.
Vehicle doesn’t work after going through water or snow.
• Water in the electronics area.
• Vehicle will take several hours to dry. Allow to dry
thoroughly overnight before trying again. Avoid driving in
water or snow.
90 DAY LIMITED WARRANTY – TYCO® R/C PRODUCTS
Mattel, Inc. warrants to the original consumer purchaser that this product will be free of defects in
material and workmanship for ninety (90) days (unless specified in alternate warranties) from the date of
purchase. Mattel will replace the product in the event of such a defect within the warranty period.
In the event of a defect covered under this warranty, first call the toll-free number listed below.
Many problems can be solved in this manner. If necessary, you will be instructed to return the product,
postage prepaid and insured, to the address below. Enclose your name, address, dated sales receipt,
and a brief explanation of the defect. Replacement and return shipment will be free of charge.
This warranty does not cover damage resulting from unauthorized modification, accident, misuse or
abuse. If the product is returned without a dated sales receipt the product may be excluded from
coverage under this warranty.
© 2004 Mattel, Inc., 333 Continental Blvd., El Segundo, CA 90245 U.S.A.
Consumer Affairs: 1 (800) 524-TOYS. PRINTED IN CHINA. All Rights
Reserved. MATTEL, TYCO and associated trademarks and trade dress
are owned by Mattel, Inc. Retain this address for future reference:
Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline
01628 500303. Mattel Australia Pty Ltd., Richmond, Victoria 3121 Consumer Advisory Service: 1300 135 312. Mattel East Asia Ltd, Room
1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK,
China. Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot
13.5, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410
PJ. Tel: 03-78803817, Fax: 03-78803867.
Mattel’s liability for defects in material and workmanship under this warranty shall be limited to repair or
replacement, at our sole option, and in no event shall we be responsible for incidental, consequential, or
contingent damages (except in those states that do not allow this exclusion or limitation). This warranty
is exclusive, and is made in lieu of any express or implied warranty. Valid only in U.S.A. This warranty
gives you specific legal rights and you may have other rights, which vary from state to state. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusions or limitations
may not apply to you.
TOLL-FREE NUMBER: 1-888-557-TYCO (8926) (valid only in U.S.A.)
Hours: 8:00 A.M. - 5:00 P.M. Eastern Time; Monday - Friday. Expect some delay in January following the
holiday season. Please be patient and keep trying the toll-free number.
ADDRESS FOR RETURNS:
CONSUMER RELATIONS
636 GIRARD AVENUE
EAST AURORA, NY 14052
COMPLIANCE WITH FCC REGULATIONS (VALID IN U.S. ONLY))
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This device generates and uses radio frequency energy and if not
used properly may cause interference to radio and
television reception. It has been tested and found to comply with
the limits set by the FCC which are designed to provide reasonable protection against such interference.
NOTE: Changes or modifications not expressively approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:11:29 14:28:31+08:00
Modify Date                     : 2004:11:29 14:28:31+08:00
Page Count                      : 4
Creation Date                   : 2004:11:29 06:28:31Z
Mod Date                        : 2004:11:29 06:28:31Z
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : 
Metadata Date                   : 2004:11:29 06:28:31Z
Creator                         : ,
Title                           : C4639-0920   1L IS
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PIYC4639-04A4R

Navigation menu