Mattel Asia Pacific Sourcing DNM64-16A5R HW RC Sky Shock User Manual DNM64R
Mattel Asia Pacific Sourcing Ltd. HW RC Sky Shock DNM64R
DNM64R User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2988586 |
| Application ID | nENcC0YWl3A6Ys/uMpf/Kg== |
| Document Description | DNM64R User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 81.41kB (1017650 bits) |
| Date Submitted | 2016-05-12 00:00:00 |
| Date Available | 2016-05-13 00:00:00 |
| Creation Date | 2016-04-22 14:13:16 |
| Producing Software | Adobe Acrobat 11.0.0 |
| Document Lastmod | 2016-04-22 14:13:16 |
| Document Title | DNM64R User Manual |
| Document Creator | Adobe Acrobat 11.0.0 |
DNM63 HW 1L I/S SIZE:594X210 mm COLOR: 4C+4C BATTERY SAFETY INFORMATION PERFORMANCE TIPS RACE IN THE AIR PRE-FLIGHT CHECK 1. Give yourself plenty of flying room. For best results, operate vehicle in a wide open area. 2. Avoid buildings, trees and power lines as they may obstruct your flight path. 3. PLAY SAFELY – Do not drive or fly vehicle in the street! Watch out for people, animals and obstacles. 4. DO NOT attempt to operate your vehicle in strong winds. Wind will make it difficult to fly safely and will reduce battery life and flying time. Remember that the wind may be stronger higher up in the sky than at ground level. • Launching into a gentle breeze will allow the vehicle to take off with the least amount of runway space. • Make small, smooth and slow movements on the throttle and steering joysticks. • Vehicle can be hand launched by holding it directly under the wings, then pushing the throttle joystick completely forward and gently throwing the vehicle ahead, parallel to the ground. • Point your controller up, not down toward your vehicle. If your vehicle gets too far away, it won’t work properly. • Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle or controller does get wet, wipe it with a towel, remove batteries, and allow to dry completely overnight. Replace with fresh batteries before next use. REPAIR & TROUBLESHOOTING FLYING THE VEHICLE Switch controller and vehicle on, synchronize them and then select FLIGHT ( Taking Off: Place the vehicle on the ground and stand behind it. ) Mode. Maintaining Flight: To increase altitude, push the throttle Push the throttle joystick completely forward until the vehicle begins to take flight. If the plane veers right or left during take off, push the steering joystick to the opposite direction to keep moving forward. Once you've reached your desired altitude, slowly pull back on the throttle joystick to level off. joystick forward. 1. Use clear household tape to repair tears, creases or cracks. Use sparingly as added weight will affect performance. 2. Dirt or mud on the vehicle can affect its operation. Use a clean, dry cloth to remove any dirt immediately. If the vehicle gets wet, turn it off and allow it to dry completely overnight. 3. When the vehicle does not respond, slows down, or loses range, recharge the vehicle. If performance does not improve following a recharge, install fresh alkaline batteries in the controller. 4. Radio interference can affect your vehicle’s performance. Interference can be caused by other R/C vehicles running on the same frequency, electrical wires, large buildings, WiFi or Bluetooth. If you experience interference, turn off your vehicle and controller and relocate to a different area. 5. When exposed to an electrostatic source, the toy may malfunction. Switch OFF both the vehicle and controller. Remove batteries from the controller, wait 30 seconds, re-insert batteries and switch ON again. This should reset your controller / vehicle and let you resume normal operation. PILOT'S MANUAL In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Non-rechargeable batteries are not to be recharged. • Rechargeable batteries are to be removed from the product before being charged. • Rechargeable batteries are only to be charged under adult supervision. • Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. • Do not mix old and new batteries. • Only batteries of the same or equivalent type as recommended are to be used. • Batteries are to be inserted with the correct polarity. • Exhausted batteries are to be removed from the product. • The supply terminals are not to be short-circuited. • Dispose of battery(ies) safely. • Do not dispose of this product in a fire. The batteries inside may explode or leak. TM INSTRUCTION SHEET SPECIFICATIONS Toy No.: For best performance use alkaline batteries. Battery life may vary depending on battery brand. Part No.: Landing: Pull back on the throttle joystick and the vehicle will Steering: Keep the throttle joystick still and slowly push the descend. Just before the vehicle touches the ground, push the throttle joystick forward a little and then let go. This will level the vehicle off so it does not crash nose first into the ground. steering joystick left or right. Return the steering joystick to the center position once the vehicle is flying in the direction you want. 0970 594mm W x 210mm H Folded Size: 148.5mm W x 210mmH Type of Fold: ACCORDION ONE # colors: Colors: The vehicle comes with 4 replacement propellers - 2 for each side. If either of the vehicle's propellers break off or become damaged, replace them by following the steps below. 1. Use a coin (not included) to pry off the old propeller. DNM63 Trim Size: Protect the environment by not disposing of this product with household waste (2012/19/EU). Check your local authority for recycling advice and facilities. REPLACING THE PROPELLERS To decrease altitude, slowly pull back on the throttle joystick. HW Toy: Battery Performance Note: Coin 2. Select the required propeller. “L” is for left side (BLUE PROPELLER). “R” is for right side (RED PROPELLER). 4. Use the coin to gently push the propeller onto the pin. The coin will prevent the pin from poking your finger. 3. Align the pin from the motor with the hole in the propeller. Make sure the molded letter (L or R) on the propeller is facing the pin. Paper Stock: Paper Weight: EDM No.: Coin AGING & WEAR AND TEAR 1R VE CO 7 8 8+ OUTDOOR USE RECOMMENDED. ADULT ASSEMBLY REQUIRED. With aging and wear & tear, the flying performance of the vehicle may be affected. If that happens, adjust the tail up or down as necessary to improve flying performance. Keep these instructions for future reference as they contain important information. IMPORTANT: Please read all instructions before operating your vehicle. ©2016 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303.Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: (852) 3185-6500.Diimport & Diedarkan Oleh: Mattel Southeast Asia Pte. Ltd. , No 19-1, Tower 3 Avenue 7, Bangsar South City, No 8, Jalan Kerinchi, 59200 Kuala Lumpur, Malaysia. Tel: 03-78803817, Fax: 03-78803867. Colors and decorations may vary. LiPo(LITHIUM POLYMER) BATTERY INFORMATION RACE CAR TO RACE PLANE • FULLY CHARGE THE BATTERY BEFORE STORING FOR AN EXTENDED PERIOD OF TIME (6 MONTHS OR LONGER). PERIODIC CHARGING EVERY FEW MONTHS IS RECOMMENDED TO EXTEND BATTERY LIFE WHEN NOT IN USE. DO NOT STORE NEAR HEAT OR IN DIRECT SUNLIGHT. • DO NOT DISASSEMBLE THE VEHICLE'S PERMANENTLY INSTALLED LiPo (Lithium Polymer) BATTERY. IT IS A SEALED LiPo BATTERY. TO PROPERLY RECYCLE, FOLLOW LOCAL LITHIUM POLYMER BATTERY RECYCLING GUIDELINES. • DO NOT RECHARGE THE VEHICLE IF IT FEELS HOT. ALLOW IT TO COOL BEFORE RECHARGING. • VEHICLE IS ONLY TO BE CHARGED USING THE CONTROLLER/CHARGER SUPPLIED. DO NOT CHARGE THE LiPo BATTERY IN ANY OTHER BATTERY CHARGER. • DO NOT ATTEMPT TO USE OR CHARGE THE VEHICLE IF IT SHOWS SIGNS OF LEAKAGE OR CORROSION. • IF THE VEHICLE AND/OR CONTROLLER ARE WET, THOROUGHLY DRY BEFORE USING OR CHARGING. • REGULARLY EXAMINE ALL WIRES AND CONNECTORS. IN THE EVENT OF DAMAGE, DISCONTINUE USE. 1. Unscrew the battery cover with a Phillips head screwdriver (not included). 2. Install 6 AA (LR6) alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries. 3. Replace battery cover and tighten screws. 4. Replace batteries in the controller if the vehicle runs slowly after a recharge or if you see a green light flashing in the controller power switch during play. FEATURES 3. PAIRING THE CONTROLLER AND VEHICLE 2. CHARGING THE VEHICLE ABOUT THE CONTROLLER MUST CHARGE VEHICLE BEFORE FIRST USE. CHARGE TIME IS APPROXIMATELY 80 MINUTES OR MORE. Your vehicle is powered by a LiPo battery that is permanently installed. The vehicle must be charged before play. It can be charged with the controller or with the USB cable. CHARGING WITH THE CONTROLLER ABOUT THE VEHICLE TRANSFORMATION / GROUND ( ) / FLIGHT ( ) MODE SWITCH – Use to transform and select between Ground Mode and Flight Mode. THROTTLE JOYSTICK – Controls both motors and is used to make the vehicle move forward / ascend / descend. STEERING JOYSTICK – Controls the left and right motors independently to make the vehicle turn left / right. CONTROLLER POWER SWITCH • Select ( ) to switch controller ON. • Select ( ) to switch controller OFF. • Select ( ) to charge the vehicle. ALIGNMENT ADJUSTMENT BUTTONS – Use to correct the direction of the vehicle if it veers to either side. POWER CABLE SOCKET – Use to charge the vehicle with the USB cable (included). VEHICLE POWER SWITCH • Select ( ) to switch vehicle OFF. • Select ( ) to switch vehicle ON. CHARGING SOCKET – Use to charge the vehicle’s internal LiPo battery. 1. To charge, first make sure you have installed 6 AA alkaline batteries in the controller and that both the controller and vehicle are switched OFF ( ). 2. Open the cover on the controller and take out the charging cable (see a ). 3. Insert the charging plug firmly into the socket under the vehicle. Make sure the connection is secure (see b ). 4. To begin charging, move the controller power switch from OFF ( ) to CHARGE ( ). A red light in the power switch will turn on. This indicates the vehicle is charging. (see c ). 5. The charging process takes approximately 80 minutes or more. The red light will go off when charging is complete. 6. Move the controller power switch from CHARGE ( ) to OFF ( ). 7. Hold the charging plug and gently pull it out of the socket. NEVER pull on the cable as this may cause the cable to break. 8. Replace the charging cable into the controller and close the cover. 9. The vehicle will usually have about 5-6 minutes of flight time once fully charged. You must pair the controller with the vehicle before you can control it. FIRST SWITCH ON THE VEHICLE, THEN IMMEDIATELY SWITCH ON THE CONTROLLER. The controller power switch changes from a flashing green light to a solid green light when pairing is complete. If the green light does not stop flashing after a few seconds, switch off the controller and vehicle, then try again. CHARGING WITH THE USB CABLE NOTES: • DO NOT hold or obstruct wings during transformation. • Vehicle will NOT transform in the air while flying. • Vehicle MUST be on the ground in order to transform. RACE ON THE GROUND DRIVING THE VEHICLE Switch controller to GROUND ( NOTE: WHEN PLAYING WITH MULTIPLE VEHICLES, EACH MUST BE PAIRED ONE AT A TIME. A maximum of 6 vehicles can be paired in one location. ) Mode. 4. ALIGNMENT ADJUSTMENT It is recommended that you check the vehicle's alignment before playing. Ground Mode 1. Switch controller to GROUND ( ) Mode. 2. Push the throttle joystick forward to see if the vehicle will drive straight. 3. If the vehicle veers right, stop the vehicle and press the left alignment adjustment button 2 or 3 times. 4. If the vehicle veers left, press the right alignment adjustment button 2 or 3 times. 5. Repeat steps 3 or 4 until the vehicle can travel in a straight line. 1. Connect the controller to a powered USB port with the supplied USB cable. 2. Follow the same instructions as detailed in CHARGING WITH THE CONTROLLER. 3. Remember to disconnect the USB cable from the controller before play. 1. Switch controller to FLIGHT ( ) Mode. 2. Push the throttle joystick forward until the vehicle takes off. 3. The vehicle may veer to one side because of wind or turbulence. Use the steering joystick to make the vehicle fly straight and level and then let go of the joystick. 4. Observe the vehicle and see if it will fly straight or veer to one side. 5. If the vehicle veers right, stop the vehicle and press the left alignment adjustment button 2 or 3 times. 6. If the vehicle veers left, press the right alignment adjustment button 2 or 3 times. 7. Repeat steps 5 or 6 until the vehicle can fly in a straight line. NOTE: Alignment adjustment settings reset when controller is switched off and will need to be checked before each use. The alignment adjustment button can be pressed a maximum of 15 times in either direction. • The toy is not intended for children under 8 years old. • Keep fingers, hair and loose clothing away from the propellers while the vehicle is switched ON. • Stay at least 3 to 6 feet away from the vehicle. That goes for anyone watching as well. • Always keep an eye on the vehicle. If it looks like it’s going to crash into you, your friends or anything else, release the throttle joystick and step out of the way. • Never disassemble or attempt to modify the vehicle. • When not in use, turn off vehicle and then controller. To avoid accidental operation, remove batteries in controller. • Operating range of controller is around 200 ft (60 m). RACE PLANE TO RACE CAR Flight Mode THE VEHICLE HAS A SPECIALLY-DESIGNED DURAFORM™ BODY COMPRISED OF EXPANDED POLYPROPYLENE (EPP), MAKING IT LIGHTWEIGHT AND EXTREMELY RESILIENT FOR LONG-TERM DURABILITY. SAFETY INFORMATION Note to Adults: To ensure that the child’s play is both safe and fun, please review all operating instructions and safety rules with your child. service.mattel.com Adult supervision is recommended when the vehicle is being operated. TRANSFORMATION 1. CONTROLLER BATTERY INSTALLATION CAUTION: SET UP DNM64-0970 DNM65-0970 Asst.DNM63 Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts. CONTENTS COVER RIGHT LEFT FORWARD FORWARD LEFT NOTES: • The vehicle drives best on flat, smooth surfaces. Avoid driving through wet areas. • To conserve battery life, the vehicle and controller goes to sleep when 5 left idle for 5 minutes. To wake up and continue play, switch the vehicle and controller OFF and then ON again. FORWARD RIGHT
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2016:04:22 14:13:16+08:00 Creator : Adobe Acrobat 11.0.0 Modify Date : 2016:04:22 14:13:16+08:00 Title : XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:04:22 14:13:16+08:00 Creator Tool : Adobe Acrobat 11.0.0 Format : application/pdf Document ID : uuid:d7bf22a9-383e-4954-8baf-df94a0f8edaf Instance ID : uuid:28a67810-77be-42e6-8fcc-f9610dc1c17b Producer : Adobe Acrobat 11.0.0 Page Count : 2EXIF Metadata provided by EXIF.tools