Mattel Asia Pacific Sourcing FNF59-17A5S Wearable Baby Monitor User Manual EN QSG Long 072017 V3
Mattel Asia Pacific Sourcing Ltd. Wearable Baby Monitor EN QSG Long 072017 V3
User Manual
Cleaning instructions
The band is washable
Cold water washMachine washHand wash
Cleaning and drying your sensor:
Because the sensor is water resistant, you can use a lightly dampened
cloth to wipe it clean. External heat sources such as hair dryers can
cause damage.
Setup Guide
©2016 Mattel. All Rights Reserved.
Protect the environment by not disposing of this product or any
batteries with household waste. This symbol indicates that this
product shall not be treated as household waste. Check your
local authority for recycling advice and facilities.
This equipment has been tested and found to comply with the limits for
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s authority
to operate the equipment.
FCC ID: PIYFNF59-17A5H
Model: Modèle: FNF59
FCC ID: PIYFNF59-17A5S
a Class B digital device, pursuant to part 15 and 18 of the FCC rules. These
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Part 15 of the FCC Rules. Operation is subject
Responsible Party: Mattel Inc., 636 Girard Avenue,
East Aurora, NY 14052, U.S.A. 1-877-219-8335
FCC Declaration of Conformity
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Part 18 of the FCC Rules. Operation is subject
For customer support, please visit service.fisher-price.com or call us at
1-877-219-8335.
3. When the battery is fully charged the Smart Charger light will turn off.
2. Place the wearable on top of the Smart Charger, which will blink white
slowly when charging.
1.
2.
3.
4.
5.
6.
7.
Remove the Smart Charger, wearable, cable, and wall plug from
the box.
Plug the cable into the Smart Charger.
Plug the cable into the wall plug, and then plug it into a power
outlet in the room where your baby sleeps.
Place the wearable on top of the Smart Charger.
The Smart Charger will flash white briefly after being plugged in.
Then after about 1 minute it will blink blue to indicate it's ready to
pair with your smart device (smart device not included).
The Fisher-Price® Sproutling® app is available on the App Store®
and Google Play™. Download the app and follow the directions to
complete set up.
When successfully connected to Wi-Fi, the Smart Charger will turn
green and play a chime.
For information on available compatible devices, please visit www.fisherprice.com/sproutling. Apple and the Apple logo are
trademarks of Apple Inc., registered in the U.S. and other countries.App Store is a service mark of Apple Inc., registered in the U.S.
and other countries. Google Play and the Google Play logo are trademarks of Google Inc.
Keep the wearable within 25 feet of the Smart Charger to maintain
connection.
the ankle. Check the smiling face on the tab
of the band to make sure it’s smiling at you.
Setting up Putting on the wearable
Put the band on the wearable. Make sure the band ring fits
completely into the groove around the sensor. The tabs on the
sensor should be on the inside, touching baby’s skin.
1. Remove the wearable from your baby when your baby is awake and
charge it in between naps.
1.
Band
Sensor
About 30 minutes before your baby goes to
sleep, put the wearable on the back of your
baby’s ankle.
Make sure the wings of the band point down
toward the ground for a fit that conforms to
2.
Fix the wearable on the back of baby’s ankle by inserting the back
of the tapered end into the slot and pressing down on both pieces
of velcro. Then slide the band up the leg toward the knee. The band
should be snug but not too tight.
3.
You can put clothes or socks on top the wearable. Do not put
clothing between the band and baby’s skin.
4.
How to charge the wearable
To receive the most accurate insights, please make sure the sensor
is fixed onto the back of your baby’s high ankle, directly against the
skin, and that it does not spin or shift around.
Quick Start Guide for Sproutling Baby Monitor (US)
Part number: 465-0009
Material: 80gsm
Dimension: 528mm x 84mm
Tolerance: ±1mm
Date: 7/19/2017
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7 .
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only on a table top, open area.
10.
11.
12.
13.
Clean the Smart Charger with a dry cloth only.
Dispose of battery safely.
Unplug this apparatus during lightning storms or when unused for
long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
Mattel Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A.
1-877-219-8335
1.
2.
3.
4.
5.
6.
Warning
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. Keep these instructions.
Rating plate was located at bottom enclosure of the apparatus.
The AC/DC adaptor shall not be exposed to dripping or splashing
and that no objectsfilled with liquids, such as vases, shall be placed
on apparatus.
The AC/DC adaptor is used as disconnect device. The AC/DC
adaptor of apparatus should not be obstructed OR should be
easily accessed during intended used. To be completely
disconnect the power input, the AC/DC adaptor of apparatus shall
be disconnected from the mains.
Battery shall not be exposed to excessive heat such as sunshine,
fire or the like.
No naked flame sources such as lighted candles should be placed
on the apparatus.
Keep these instructions for future reference as they contain
important information.