Mattel Asia Pacific Sourcing G3448-05A2T 1/6 batmobile User Manual G3448 0920 new 7 2v 1L

Mattel asia Pacific Sourcing Ltd. 1/6 batmobile G3448 0920 new 7 2v 1L

USERS MANUAL

TYCO R/C SUPPORTQuestions or problems with your product? DON’T RETURN IT TO THE STORE!Just call us for help. U.S. consumers may also register their products at this number.1 888 557-TYCO (8926) ®tycorc.comKeep these instructions for future reference: theycontain important information. IMPORTANT: Pleaseread all “Consumer Information” (last page) before operating your vehicle.NOT RECOMMENDED FOR CHILDREN UNDER 6 YEARS OF AGE. AS WITH ALL ELECTRIC PRODUCTS,PRECAUTIONS SHOULD BE OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK. INPUT:120VAC, 60Hz, 12VA. OUTPUT:8.5VDC, 420mA, 3.6W.CAUTION-ELECTRIC TOY:SQyG3448-0920G3448-S11 2 3qweurI.CONTENTS/FEATURESVehicleTransmitter7.2v Battery pack 7.2v wall charger 5AA BatteriesVehicleqTry-Me-with light and engine soundwAdjustable airbrakeseMultiBand™ selector switch*Please see the “MultiBand™ Feature” section for moreinformation.r ON/OFF/Try-Me (light and sound) switch*This switch has three positions:I Vehicle On: Vehicle runs with sounds effects and light as you driveO Vehicle OFFVehicle On: Activates 'try me' function with lights and engine soundst3AA battery doorySteering adjuster*For when your vehicle appears to veer to either the right orleft. Use screwdriver (not included) to turn the knob in thedirection necessary to correct the vehicle's alignment.u7.2v battery dooriBattery latchTransmitterq Vehicle controlsw Antennae LED light-indicates battery strengthr MultiBand™ selector switchtBattery door*Please see the “MultiBand™ Feature” section for moreinformation BatmobileBatmobileTMtiwTRY MEq123IOerFORWARD REVERSE LEFT RIGHTII. VEHICLE OPERATIONXCAUTION: Surfaces may become hot and cause burns ifelectronics get wet. Do not operate vehicle throughwater or snow.t
III. MULTIBAND™FEATURE• Your vehicle features the advanced Tyco® R/C MultiBand™system. This system lets you race your vehicle head-to-head– against up to two of your friends (up to 3 drivers total) –without any radio interference from your friends’ transmittersor vehicles. You must be racing against another Tyco® R/CMultiBand™-equipped vehicle for this feature to work.• There’s one MultiBand™ selector switch on your vehiclechassis, and another one on your transmitter. The vehicleswitch has 3 positions: one for each MultiBand™ setting. The transmitter switch has 3 positions: one for eachMultiBand™ setting.• For successful operation, the vehicle switch and the transmitter switch must be set to the same MultiBand™ setting. When you’re driving by yourself, you can set theswitches to any of the 3 MultiBand™ settings (as long asthey match).• When you want to race head-to-head, just make sure thateach driver (up to 3 drivers total) has a vehicle and transmitter set to a different MultiBand™ setting.*The transmitter’s MultiBand™ selector switch also servesas the transmitter’s power switch. To operate your vehicle, just turn the vehicle ON; then set the transmitterswitch to the desired MultiBand™ setting. Push any transmitter control and you will be able to run and controlyour vehicle.*You must be racing against another Tyco® R/CMultiBand™-equipped vehicle for this feature to work. Anon-MultiBand™ vehicle, running on the same frequencyas your vehicle, may interfere with operation of your vehicle. If you are racing against a non-MultiBand™ vehicle, make sure that vehicle operates on a frequencydifferent from yours.*If you need to change the MultiBand™ setting, first makesure that your vehicle is turned OFF. Change the switchposition as desired, making sure to change both the transmitter AND the vehicle switches. Then turn yourvehicle back ON for more racing action. NOTE: Make certain you’re not pressing a transmitter control whilechanging selector switch position.123Transmitter1. Remove the battery cover as shown.2. Install 2 AA alkaline batteries with polarity (+/-) as showninside the battery compartment.3. Replace the battery door.There are two power sources: a 7.2v SubC NiCad rechargeablebattery pack (which powers all the driving and turning) and a 3AA Alkaline battery pack (which powers the lights, sounds andRF receiver).For detailed information regarding rechargeable battery charging and safety, please refer to the “BatteryCharging/Care” section.VehicleFor lights, sounds and RF receiver position batteryinstallation:1. Use a screwdriver (not included) to unscrew the powerclip cover screw, open the battery cover as shown.2. Install 3 AA alkaline batteries with polarity (+/-) as showninside the battery compartment.3. Replace the battery door.IV. BATTERY INSTALLATION7.2 v d.c. 7.2 v d.c.1 2 3For driving battery installation:1. Rotate the battery door latch to the unlocked position andopen the battery door.2. Insert the charged battery pack into the battery compartment as shown.3. Connect the battery pack’s wire connector to the vehicle’scharging jack as shown. Make certain the connector issecurely connected.4. Close the battery door and rotate the battery door latch tothe locked position.1237.2v d.c.
V. BATTERY CHARGING/CAREXCAUTION: Use only the charger supplied with thistoy. Do not use any other charging source.Use only Tyco® R/C 7.2v NiCd battery packs. Other batteriesmay leak or rupture, causing personal injury and damage.1. Plug the wall pack charger into a standard wall outlet.2. Connect the battery pack’s wire connector to the wall packcharger connector. Make certain the two connectors aretightly snapped together.3. To disconnect the wires, push down on the connector clipand pull apart.4. After charging, the battery will feel warm. This condition isnormal for fully charged batteries.5. New battery packs must be charged for 5 1/2 hours the firsttwo times charged. Subsequent charges will require 4hours. Charging the battery pack for more than 5 1/2 hourswill not give you a longer running time. 5 1/2 hours is all thatis required for a fully charged battery pack.6. Unlike alkaline batteries, which lose power gradually, a NiCd(Nickel-Cadmium) battery will run for its normal running timeand then lose most of its power at once. That’s how you’llknow it’s time to recharge the battery pack.7. After use, the battery pack will be hot! Wait at least 20 minutes until the battery pack cools before recharging.Recharging a warm or hot battery pack will greatly reducethe number of times your battery pack can be recharged.RECHARGEABLE BATTERY INFORMATION: DO NOT RECHARGE BATTERY PACK IF IT’S HOT. ALLOW IT TO COOL BEFORE RECHARGING. DO NOT RECHARGE A BATTERY PACK THAT SHOWSLEAKAGE OR CORROSION. DO NOT DISASSEMBLE THE BATTERY PACK. THE BATTERY PACK IS A SEALED RECHARGEABLE NICKEL-CADMIUM BATTERY. EXERCISE CAUTION IN HANDLING A HOT BATTERY PACK. IF BATTERY PACK AND/OR CHARGER ARE WET, THOROUGHLY DRY BEFORE CHARGING. DO NOT RECHARGE NON-RECHARGEABLE BATTERIES.Note to Adults: • Remove rechargeable batteries before recharging. Rechargebatteries only under adult supervision.• Regularly examine for damage to the cord, plug, enclosureand other parts. •In the event of any damage, the toy must not be used withthe battery charger until the damage has been repaired. • This toy is not intended for children under 3 years old. Thebattery charger is not a toy.THIS PRODUCT USES A NICKEL-CADMIUM RECHARGEABLEBATTERY PACK. BATTERY MUST BE RECYCLED OR DISPOSEDOF PROPERLY. FOR FURTHER INFORMATION REGARDING BATTERIES OR THEIR DISPOSAL PLEASE CALL 1-888-557-TYCO.VI. CONSUMER INFORMATION:QUICK TIPSqWhen the 3AA batteries in the vehicle are running low thesound effects and motor will cut off. You'll then hear a 10-second beep. Change to new AA batteries. When the 7.2vSubC NiCad is low or encounters a stall, the unit will cut themotors and turn off the sound effects. The unit will beep aslong as the user continues to press the remote control.wYour vehicle's running time may change depending on your driving style.eRadio interference can make your vehicle run badly.Interference can be caused by other non-MultiBand™ R/Cvehicles running on the same frequency; electrical wires;large buildings; CB radios; or other wireless gear. Try tostay away from these!rPoint your transmitter antenna up - not down toward yourvehicle. If your vehicle gets too far away, it won't workproperly. tDon’t drive your vehicle in sand or through water or snow.If your vehicle does get wet, wipe with a towel and allow itto dry completely.yDon’t store your vehicle near heat or in direct sunlight.Always turn switches OFF and remove all batteries for storage.qwerty
TROUBLESHOOTING - PROBLEM? - SOLUTIONSSYMPTOMVehicle runs slowly or will not run.Erratic operation or only short range possible.Short rechargeable battery life.Vehicle doesn’t work after going through water or snow.• PROBABLE CAUSE• Loose battery connection or the vehicle switch is not ON.• Weak or uncharged rechargeable battery.• Weak transmitter battery.• Transmitter and vehicle MultiBand™ selector switches setto different MultiBand™ settings.• Radio interference likely.• Battery not fully charged.• Water in the electronics area.• CORRECTION• Check battery connector and vehicle switch.• Charge or replace the battery.• Replace with fresh alkaline battery.• Check MultiBand™ selector switches and change switchpositions if necessary (MultiBand™ settings must match).• Check for possible interference and change driving location if necessary (see point 2 – Quick Tips).• Recharge the vehicle battery.• Vehicle will take several hours to dry. Allow to dry thoroughly overnight before trying again. Avoid driving inwater or snow.Mattel, Inc. warrants to the original consumer purchaser that this product will be free of defects in material and workmanship for ninety (90) days (unless specified in alternate warranties) from the date ofpurchase. Mattel will replace the product in the event of such a defect within the warranty period.In the event of a defect covered under this warranty, first call the toll-free number listed below. Many problems can be solved in this manner. If necessary, you will be instructed to return the product,postage prepaid and insured, to the address below. Enclose your name, address, dated sales receipt, and a brief explanation of the defect. Replacement and return shipment will be free of charge.This warranty does not cover damage resulting from unauthorized modification, accident, misuse orabuse. If the product is returned without a dated sales receipt the product may be excluded from coverage under this warranty.Mattel’s liability for defects in material and workmanship under this warranty shall be limited to repair orreplacement, at our sole option, and in no event shall we be responsible for incidental, consequential, orcontingent damages (except in those states that do not allow this exclusion or limitation). This warrantyis exclusive, and is made in lieu of any express or implied warranty. Valid only in U.S.A. This warrantygives you specific legal rights and you may have other rights, which vary from state to state. Some statesdo not allow the exclusion of incidental or consequential damages, so the above exclusions or limitationsmay not apply to you.TOLL-FREE NUMBER: 1-888-557-TYCO (8926) (valid only in U.S.A.)Hours: 8:00 A.M. - 5:00 P.M. Eastern Time; Monday - Friday. Expect some delay in January following theholiday season. Please be patient and keep trying the toll-free number.ADDRESS FOR RETURNS:CONSUMER RELATIONS636 GIRARD AVENUEEAST AURORA, NY 1405290 DAY LIMITED WARRANTY – TYCO® R/C PRODUCTSNote to Adults: To ensure that the child’s play is both safe andfun, please review all the operating instructions and safetyrules with your child.Safety Tips• NEVER drive your vehicle on streets! They’re for real cars!• DO NOT pick up the vehicle while it's in motion.• Keep fingers, hair and loose clothing away from the tires andthe wheel hubs while the vehicle is switched ON.XCAUTION: To prevent entanglement, keep hair away fromwheels.• Adult supervision is recommended when this vehicle is beingoperated.• To avoid accidental operation, remove all batteries when notin use. Always turn all switches OFF before removing batteries.BATTERY SAFETY INFORMATIONIn exceptional circumstances batteries may leak fluids thatcan cause a chemical burn injury or ruin your toy (product). To avoid battery leakage:• Non-rechargeable batteries are not to be recharged.• Rechargeable batteries are to be removed from the toybefore being charged (if designed to be removable).• Rechargeable batteries are only to be charged under adultsupervision (if designed to be removable).• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.• Do not mix old and new batteries.• Only batteries of the same or equivalent type as recommended are to be used.• Batteries are to be inserted with the correct polarity.• Exhausted batteries are to be removed from the toy.• The supply terminals are not to be short-circuited.• Dispose of battery(ies) safely.• Do not dispose of this toy in a fire. The batteries inside mayexplode or leak.Battery Performance Note:For best performance use regular or high-performance alkalinebatteries (where disposable batteries are called for). If your vehicleis supplied with standard (carbon-zinc) batteries for initial useand/or demonstration purposes, we recommend replacing themwith alkaline batteries when necessary. Battery life may varydepending on battery brand.© 2005 Mattel, Inc., 333 Continental Blvd., El Segundo, CA 90245 U.S.A. Consumer Affairs: 1 (800) 524-TOYS.PRINTED IN CHINA. All Rights Reserved. MATTEL, TYCO and associated trademarks and trade dress areowned by Mattel, Inc. Retain this address for future reference: Mattel U.K. Ltd., Vanwall Business Park,Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty Ltd., Richmond, Victoria 3121 -Consumer Advisory Service: 1300 135 312. Mattel East Asia Ltd, Room 1106, South Tower, World FinanceCentre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P)Lot 13.5, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.COMPLIANCE WITH FCC REGULATIONS (VALID IN U.S. ONLY)This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.This device generates and uses radio frequency energy and if not used properly may cause interference to radio and television reception. It has been tested and found to comply with the limits set by the FCC which are designed to provide reasonable protection against such interference.NOTE: Changes or modifications not expressively approved by the manufacturer responsible forcompliance could void the user’s authority to operate the equipment.BATMAN and all related characters and elements are trademarks of and ' DC Comics.WB SHIELD: TM & ' Warner Bros. Entertainment Inc.(s05)TM

Navigation menu