Mattel Toys A Division of Mattel 47999-02A2T Remote Control Toy Transmitter User Manual 47248 I S new
Mattel Toys A Division of Mattel Inc Remote Control Toy Transmitter 47248 I S new
User Manual
47999-9993 MINI SKATEBOARD Apr. 10. 02 Apr. 10. 0247999-9993 MINI SKATEBOARD
BATTERY INSTALLATION:
•Skateboard •Stickers
GETTING STARTED
•Controller
© 2002 Mattel, Inc., El Segundo, CA 90245 U.S.A. All Rights Reserved. Mattel East Asia Ltd.,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Retain this address for future reference:
Mattel U.K., Ltd., Vanwall Business Park, Maidenhead SL6 4UB.
Help line 01628500303
BATTERY SAFETY INFORMATION
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the
toy before being charged (If designed to be removable).
• Rechargeable batteries are only to be charged under
adult supervision (If designed to be moveable).
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as
recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Dispose of batteries safely. Do not dispose of in fire as
batteries may explode or leak.
• Products with non-replaceable batteries are not to be disposed
of in a fire as the batteries inside may explode or leak.
CAUTION:
To prevent entanglement,
keep hair away from wheels.
47999-9993-S1
Please keep these instructions for future reference, as they contain important information.
2. Insert 3 "AA" (LR6) alkaline batteries
(not included), as indicated inside the
battery compartent. Remove the labels from the sticker sheet and place
anywhere on the skateboard, helmet and/or controller
•Hair band removal installation
Pull ends of strips to release hair. Remove any remaining
thread from hair.
3. Replace and screw the battery door
after installing the batteries
1. Unscrew and remove the battery door.
2. Insert one "9V" alkaline battery (not included), as indicated inside the battery
compartent.
3. Close the battery door.
Surface washable
1. Slide open the battery door.
1. Press the power ON/OFF button on the
top of the skateboard to turn the unit
on and off.
4. To turn the product off, pick up by the back
of the skateboard or lift the doll by the head and
press the On/Off button.
2. The skateboard spins clockwise continuously
when the Power button is pressed ON.
3. When you hold the button on the controller down,
the skateboard will tilt back into a wheelie and move
forward until the button is released. The skateboard
will then continue to spin until the button is pressed
down again.
NOTE: Changes or modifications not expressively approved by the manufacturer responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Mattel Inc.
333 Continental Blvd.
El Segundo,CA
(310) 252-2400
• Operating multiple vehicles with the same frequency in close proximity will cause interference
and poor performance.
• Works best away from high voltage power lines, large buildings and walls.
• Hold the transmitter antenna up for best performance.
• When the product does not respond, slows down, or loses range, change the batteries.
• If transmitter is accidentally dropped in the water, remove battery(ies) and allow transmitter to air
dry. Replace with fresh battery(ies) before operation.
• Requires 3 AA alkaline batteries for the skateboard and one 9-V alkaline battery for the transmitter.
• Play Safely! - Do not drive vehicle in the street!
• For longer life use only alkaline batteries.
• This product is not recommended for use on loose dirt or wet surfaces.
• Do not immerse in water.
Screwdriver
not included
Power OFF
Power ON
R/C toy operates from up to 30 feet (9m) away.
This product operates at a frequnecy of 27MHz