Maxell ME-M21 RFID Reader/Writer Module User Manual Installation Manual

Download:
Mirror Download [FCC.gov]
Document ID	738281
Application ID	HVs9X7zNrfEgq/FpMZN5Xg==
Document Description	Installation Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	127.99kB (1599827 bits)
Date Submitted	2006-12-14 00:00:00
Date Available	2006-12-14 00:00:00
Creation Date	2006-12-01 04:49:04
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2006-12-06 16:04:28
Document Title	Installation Manual.pdf
Document Creator	PScript5.dll Version 5.2
Document Author:	07665

“SEGA NETWORK CASINO CLUB” IC CARD
The RFID unit is attached to the front of the cabinet close to where the player plays the
game, as in the picture below. It is used to read and write information on IC Cards.
IC Cards contain information such as the names of game characters, clothing and
accessory combinations, and game results.
(Although the information stored on the IC Card may vary depending on the game, the
card’s purpose remains the same)
[Reference... Sample cabinet]
RFID UNIT
RFID Reader/Writer Module
9 CARD R/W
[!] WARNING
ŏ When working with the product, be sure to turn the power off. Working with the power on may
cause an electric shock or short circuit.
ŏ Be careful not to damage the wires. Damaged wires may cause an electric shock or short
circuit.
ŏ Be careful not to lose screws, nuts or other fasteners. If metallic fasteners come in contact
with electrically charged areas, they may cause an electric shock, short circuit or present a risk
of fire.
(STOP) IMPORTANT
ŏ Be careful not to get your hands or fingers caught when opening or closing the card R/W cover.
ŏ The solenoid on the RW unit can get hot. Exercise caution so as to avoid burns.
9-1 Cleaning
If the IC card is difficult to insert, or does not come out from the reader, the interior of the card
reader may be dirty. Clean the card reader in such cases.
Please turn off the power switch before carrying out this procedure.
[!] WARNING
Observe the following points when cleaning so as not to damage component surfaces.
ŏ Remove smears using a dry, soft cloth (flannel, etc.). Do not use coarse gauze, etc.
ŏ For a smear-removing solvent, alcohol (ethanol) is recommended. When using chemical
detergent, be sure to follow the instructions below:
- Soak a soft cloth in a neutral household detergent diluted with water. Wring the cloth well
then wipe down the surface.
- Do not use bleach or detergent that contains abrasive agents.
- Do not use alkaline chemical detergents such as "glass cleaner" or solvents such as thinner,
etc.
ŏ Do not scrape or scratch the surfaces using brushes, scouring pads or other coarse cleaning
utensils.
1. Turn off power to the satellite.
2. Unlock the right side of the cabinet with the maintenance key and remove the card R/W cover.
Pull the card R/W cover 5 mm toward you, and then pull at an angle to remove it.
Make sure the cover does not come into contact with other surrounding parts at this time.
Unlock
FIG.9-la
FIG. 9-1a
Unlock
3. Remove 2 screws, then disconnect 3 connectors while pulling the ASSY card R/W toward you.
Be careful not to damage wiring at this time.
Disconnect connector
SCREW(2)
M4x8, w/flat & spring washers
FIG.9.1b
FIG. 9-1b
SCREW (2) / M4x8, w/flat & spring washers
Disconnect connector.
4. Remove 4 screws and remove the RW guide upper.
SCREW (4)
M4x10,w/flat&spring washers
RW GUIDE UPPER
FIG.9-1c
Be careful not to lose the roller
FIG. 9-1c
SCREW (4) / M4x10, w/flat & spring washers
RW GUIDE UPPER
Be careful not to lose the roller.
5. Wipe off dirt from the surface which the IC Cards contact. If foreign objects get in, remove
them. The roller is a small component. Be careful not to lose it or any of the screws.
ROLLER
FIG. 9-1d
ROLLER
FIG. 9-1d
6. After wiping with a damp cloth, make sure that surfaces have dried adequately.
7. Reattach the RW guide upper. Attach RW guide upper so that the pushrod of RW guide lower
is inserted into the hole of RW guide upper. Be careful not to lose the roller at this time.
PUSHROD
FIG.9-1e
FIG. 9-1e
PUSHROD
8. Attach lock arm while checking the following points. After attaching, move the pushrod by
hand and confirm that it moves normally. Also, check that the tabs go through the hole.
- Insert lock arm into pushrod underside.
- Suspend spring on rib.
PUSHROD
Suspend spring on rib
FIG. 9-1f
PUSHROD
LOCK ARM
Suspend spring on rib.
TABS
TABS
LOCK ARM
FIG.9-1f
9. Carry out the process described above in reverse order to reattach the ASSY card R/W to its
original position, and then reattach the card R/W cover. Push the cover towards the rear surface,
and then lock the cabinet.
FIG. 9-1g
FIG.9-1g
9-2 Dealing with jammed cards
If an IC card becomes stuck or jammed, push it out with your fingertip through the rectangular
holes in the RW guide upper.
FIG. 9-2
FIG.9-2
There are a variety of reasons a card may become jammed.
- An object other than an IC Card has been inserted
- String or other foreign objects are attached to the IC Card
- 3 or more IC Cards have been inserted
Although IC cards may function properly to play a game when there are objects such as stickers
attached to them, they may jam when 2 stacked cards are inserted (when continuing the game).
Be sure to check the cause for the jamming after removing the card.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2006:12:01 04:49:04Z
Modify Date                     : 2006:12:06 16:04:28+09:00
Page Count                      : 11
Creation Date                   : 2006:12:01 04:49:04Z
Mod Date                        : 2006:12:06 16:04:28+09:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : 07665
Metadata Date                   : 2006:12:06 16:04:28+09:00
Creator                         : 07665
Title                           : Installation Manual.pdf
Has XFA                         : No

EXIF Metadata provided by EXIF.tools