Maxon CIC SP0402 Private Land Mobile Radio for Handheld User Manual SP0402

Download:
Mirror Download [FCC.gov]
Document ID	730471
Application ID	+aml0sqq3GJ71sGIys9Umw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.11kB (63919 bits)
Date Submitted	2006-11-21 00:00:00
Date Available	2006-11-21 00:00:00
Creation Date	2006-11-08 13:31:21
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2006-11-08 13:31:21
Document Title	Microsoft Word - SP0402 user manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	erwin_ryu

SP-0402
Synthesized Scanning Radio
MAXON CIC
FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL USE ONLY
The Federal Communications Commission (FCC), with its action in General Docket 93-62,
November 7, 1997, has adopted a safety standard for human exposure to Radio Frequency (RF)
electromagnetic energy emitted by FCC regulated equipment. Proper operation of this radio will
result in user exposure far below the Occupational Safety and Health Act (OSHA) and Federal
Communications Commission limits.
DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more
than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded.
This radio is NOT approved for use by the general population in an uncontrolled
environment. This radio is restricted to occupational use, work related operations only
where radio operator must have the knowledge to control the user’s exposure conditions
for satisfying the higher exposure limit allowed for occupational use.
When transmitting, hold the radio in a vertical position with its microphone 1inches (2.5
cm) away from your mouth.
The radio is transmitting when the red LED on the front of the radio is illuminated. You
can cause the radio to transmit by pressing the PTT bar on the radio.
These are required operating configurations for meeting FCC RF exposure compliance.
Failure to observe these restrictions mean violation.
Safety Information
The Federal Communications Commission (FCC), with its action in General Docket 79-144,
March 13, 1985, has adopted a safety
standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC
regulated equipment. Maxon subscribes to the same safety standard for the use of its products.
Proper operation of this
radio will result in user exposure far below the Occupational Safety
and Health Act and Federal Communications Commission limits.
WARNING - DO NOT hold the radio in such a manner that the antenna is next to, or touching,
exposed parts of the body, especially the face or eyes, while transmitting.
WARNING - DO NOT allow children to operate transmitter - equipped radio equipment.
CAUTION - DO NOT operate the radio near unshielded electrical blasting caps or in an
explosive atmosphere unless it is a type especially designed and qualified for such use.
CAUTION - DO NOT press and hold the transmit switch (P-T-T) when not actually wishing to
transmit.
NOTE: This radio operates in FCC regulated frequency bands. All radios must be licensed
by the FCC before use. Because this radio contains a transmitter, Federal law prohibits
unauthorized use or adjustments of this radio.
Operating Instructions
About Your SP-0402 Radio
Maxon's SP-0402 radio feature up to 16 channels. Operation and functions for Maxon's SP-510
radios are described in this manual.
We urge you to thoroughly read this manual before operating the radio.
Application of some of the functions described in this manual is determined by the system you
use. Your Maxon Dealer will program your radio so that you have the greatest number of
functions possible relative to your needs.
Should you have questions regarding the operation of the radio please consult your Maxon
Dealer.
SP-0402 Specification
MODEL:
MODEL CODE:
EQUIPMENT TYPE:
PERFORMANCE SPECIFICATIONS:
SP-0402
7840
Hand portable
TIA/EIA-603
BAND:
CHANNEL SPACINGS:
RF OUTPUT POWER:
MODULATION TYPE:
UHF2(440~470Mhz)
12.5KHz / 25KHz PROGRAMMBLE
5 / 1 WATT
F3E
AUDIO POWER:
500mW ( EXT WITH 8 OHM)
1W ( INT WITH 4 OHM)
45.1MHz
455KHz
16 Channel
SYNTHESIZER
INTERMEDIATE FREQUENCY:
CHANNELS:
FREQUENCY SOURCE:
POWER SUPPLY:
Ni-MH(1550mA)
7.5 VDC NOMINAL EXTREME
+/- 10% VDC EXTREME
Unpacking Information
Remove and carefully inspect the contents of your package(s) for the following items:
Radio
Battery Pack
Battery Charger
Battery Charger Power Supply
Antenna
Spring Belt Clip
Operating Instructions
If any items are missing, please contact your Dealer or Maxon.
SP-0402 Features
·
·
·
·
·
·
·
·
·
·
Wideband frequency separation
1 or 5 W programmable output power
Programmable 12.5/25 kHz channel spacing
Channel scan
Priority channel scan
Look back channel
CTCSS/DCS/ tone signaling
Busy channel lockout
Time-out timer
Priority Channel Edit
Description of Radio Components
1) Antenna Receptacle
2) Channel Selector Switch
3) On/Off - Volume Control
4) RX/TX Indicator
5) Battery Latch
6) Push-To-Talk (PTT)
7) Monitor Button
8) Option Button
9) Emergency Button
10) Microphone
11) Accessory Connector (EXT Jack)
12) Belt Clip
13) Battery
14) Battery Charge Contacts
15) Speaker
Antenna Installation
Fasten the antenna to the radio by turning the antenna clockwise into the receptacle on top of the
radio.
Installing and Removing the Battery Pack
To Install:
Position the guides of the battery in line with the radio battery guide rails and slide the battery into
position until a click is heard.
To Remove:
Holding radio in one hand, push and hold battery latch button located in the upper right hand
corner of the battery pack , held as if looking at the back of the unit. Hold radio firmly and slide
battery in downward direction while pushing the battery latch button.
Attaching and Removing the Belt Clip
To Install:
Install belt clip onto the belt clip holder located on the upper left hand corner of the radio, held as
if looking at the back of the unit. Locate slot location in belt clip and push belt clip until a click is
heard.
To Remove:
Push and hold release button located at top of belt clip and slide clip off the belt clip holder.
Battery Charging and Care
To ensure peak performance from your radio, the battery pack must be fully charged. Proper care
and charging will allow maximum performance and life of your battery pack.
SPC-5000 Desktop Charger provides 2 hours charging to one radio and one battery.
To receive maximum performance from your radio and battery pack, periodically completely
discharge and recharge the battery pack.
Status Indicators and Audible Alert Tones
Your SP-0402 has a sophisticated microprocessor control which provides a series of audible alert
tones.
Upon initial power up, a quick melody indicates that the self-test of the microprocessor functions
has been completed satisfactorily. A series of tones may be sounded with any of the following
conditions:
- Attempt to transmit on a channel set for receive only
- Attempt to transmit on a channel that is already in use when busy channel lockout has
been programmed into the radio *
- Transmitting time has exceeded time-out timer programmed length *
- Low battery condition
- Selecting a channel with no programmed frequency
* Indicates a function that is initially programmed into the radio by your Maxon Dealer.
NOTE: All audible tones can be programmed off for silent operation.
Status
Normal
Decription
Power On - Ready
Call Received
Correct Call
Busy Channel
Transmit
Transmit not allowed
LED color
N/A
Orange
Green
Orange
Red
Red Flashing
Audible Tone
Melody
N/A
N/A
N/A
N/A
Two beeps
Scanning
Normal Scan mode
Green Flashing
N/A
Warning
Low Battery
Busy Channel lockout
TX Inhibit
Red Flashing
orange
N/A
Time-out-timer
N/A
Unlock
N/A
2 beeps repeated
2 beep repeated
Two beeps
Single beep/3 beeps
repeated
Two beeps
Error
Operation Mode
This section provides general descriptions of the operating modes of the SP-0402 Radio.
Power Off Mode
The SP-0402 shall enter Off mode when the On/Off Volume knob is rotated to the most counterclockwise position, beyond the detent. Upon entering Off mode, the radio shall store its current
channel (if Power On Channel function is disabled via PC programmer).
Power On Mode
The SP-0402 shall enter Power-On mode when the On/Off Volume knob is rotated clockwise
beyond the detent. Upon entry of the Power-On mode, the radio shall perform the 1 time poweron alert to indicate that it has been turned on.
High / Low Power
The radio shall be capable of programmable output power.
Each channel can be programmed via pc programmer to have either high or low power.
Or it is set by pressing option button.
Cloning
Frequencies and functions can be programmed from radio to radio by using a cloning cable.
Password
Password function is the function that the user knows the password can use the radio.
You can set password enable and the password code at pc program. And you can set password
enable/disable by programmable key (password and menu option). At this time you can enter the
password code by using EMG/PTT/MON/OPTION button.
When you press the last 4th place after enter the all code, if the code is not correct, and then
blinking the LED red and repeat 2 times error beep.
To disable password function, you can select On/Off by using Menu or programmable key
(password option).
If you enable password at the Menu Mode of the radio programmed without password, then
default password code set “NONE”
Fixed Key
(PTT)
① Press and Hold to transmit. Release to receive mode.
② Power on with press and holding PTT Key to see software version
(MONITOR)
Release squelch and tone circuit to check whether you can use or not current channel.
(OPTION)
Short pressing: scan operaiting
Look Back channel edit
Tx power H/L
(EMG)
Transmit EMG ID 5 times and generate warning audio alert during 7secs
Licensing and Service Information
FCC Licensing
The Federal Communications Commission requires that the operator of this radio be properly
licensed under the applicable Part and/or Parts of the FCC Rules and Regulations.
Consult with your Maxon Dealer, or contact the nearest FCC Field Office for information about
obtaining a license.
Service
Do not tamper with internal adjustments. Damage to the equipment and/or improper operation
may result. There are no user serviceable items inside the radio.
It is recommended that you return your radio to a qualified Maxon Dealer for any service or
repairs.
Recycling/Disposal of Batteries
The U.S. Environmental Protection Agency (EPA) classifies used Ni-MH batteries as hazardous
waste, unless certain exemptions apply.
The battery should be recycled at the end of its useful life. Under various state or local laws, such
batteries must be recycled or disposed of properly and cannot be dumped in landfills or
incinerators.
Maxon America, Inc. fully endorses and encourages the recycling of Ni-MH batteries. A national
program to collect and recycle used Ni-MH batteries is being implemented by the Rechargeable
Battery Recycling Corporation (RBRC Ö). This program is being funded through the use of
license fees paid by the battery and product manufacturers to place the RBRCÖ Seal on the
batteries.
The following is a list of facilities where the batteries can be shipped to be recycled. Contact
these facilities for proper packaging and shipping guidelines.
Software Copyrights
The Maxon products described in this operating instruction manual may include copyrighted
Maxon software programs stored in semi-conductor memories or other media. Laws in the United
States and other countries preserve for Maxon certain exclusive rights for copy-righted software
programs, including the exclusive right to copy or reproduce in any form the copyrighted software
program. Accordingly, the copyrighted Maxon software programs contained in the Maxon
products described in this operating instruction manual may not be copied or reproduced without
the express written permission of Maxon. Furthermore, the purchase of Maxon products shall not
be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Maxon, except for normal non-exclusive royalty free
license to use that arises by operation of law in the sale of a product.
Maintenance
Your SP-0402 Radio is designed to be maintenance free. To keep your radio in good working
condition:
Clean external surfaces with a clean cloth dampened in a solution of dishwasher detergent
diluted in water. Apply the solution sparingly to avoid any moisture leaking into cracks and
crevices. Do not submerge the radio. Use a non-metallic brush to dislodge stubborn particles, if
necessary. Dry the surface thoroughly with a soft, lint free cloth.
DO NOT use solvents or spirits for cleaning - they may permanently damage the housing.
Clean the battery contacts on the back of the radio with a lint free cloth to remove dirt, grease, or
other foreign material that may impede good electrical contact.
Limited Warranty
Maxon shall have no obligation to make repairs or to cause replacement required which result
from normal wear and tear or necessitated in whole or in part by catastrophe, fault or negligence
of the user, improper or unauthorized alterations, repairs to the Product, use of the Product in a
manner for which it was not designed, or by causes external to the Product. This warranty is void
if the serial number is altered, defaced or removed.
Maxon's sole obligation hereunder shall be to repair or replace the Product covered in the above
warranty.
THE EXPRESS WARRANTIES CONTAINED HEREIN ARE IN LIEU
OF ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED
OR STATUTORY, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
FOR ANY PRODUCT WHICH DOES NOT COMPLY WITH THE
WARRANTY SPECIFIED, THE SOLE REMEDY WILL BE REPAIR OR REPLACEMENT. IN NO
EVENT WILL MAXON BE LIABLE TO THE
BUYER OR ITS CUSTOMERS FOR ANY DAMAGES, INCLUDING ANY SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, OR FOR THE LOSS OF PROFIT,
REVENUE OR DATA ARISING OUT OF THE USE OF OR THE INABILITY TO USE THE
PRODUCT.
This warranty is void for sales and deliveries outside of the United States.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 9
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:dba616cd-74b1-4c73-8151-ffc20d505350
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2006:11:08 13:31:21+09:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2006:11:08 13:31:21+09:00
Document ID                     : uuid:e8f71c69-184e-41f8-ac4b-a244c0c94427
Format                          : application/pdf
Title                           : Microsoft Word - SP0402 user manual.doc
Creator                         : erwin_ryu
Author                          : erwin_ryu

EXIF Metadata provided by EXIF.tools