Maxtronic Co AIBY Disk Array User Manual Aiby1400 Ch5

Maxtronic International Co Ltd Disk Array Aiby1400 Ch5

users manual 6

Chapter 5 : " Hot Swap "This chapter explains how to remove and install the "Hot-Swap" parts without interrupting the data access while the disk array is on.The "Hot-Swap" parts include :Hard Disk Drives Cooling FansFollow the steps below and refer to the diagrams to remove and install the "Hot-Swap" parts.5-1
Hot Swap5-2 Removing / Installing Hard Disk drivesa. Unlock the HDD tray (When a HDD error occurs, the HDD LED indicator lights up "RED")Figure : Swap HDD ( Unlock )
5-3Hot Swapb. Gently pull-out the HDD trayFigure : Swap HDD ( Pull-out )
Hot Swap5-4c. Unscrew and unplug the cablesFigure : Swap HDD ( Unplug cables )UnscrewUnplug Cables
Figure : Swap HDD ( Lock Up )Hot Swap5-5d. Replace with a new Hard Disk Drive It must be same capacity or greater than the faulty drive, if you replace with a Hard disk Drive of insufficient capacity, the Disk Array's built-in buzzer will sound and the intelligent Auto-Rebuild function will not be started. * For best performance, we recommend you swap with an identical Hard Disk Drive.e. Gently Slide-in the HDD tray and lock up to start the Auto-Rebuild When you have installed the replacement disk drive, screw in all the screws and plug in the cables, you may now gently slide in the HDD tray into the chassis and lock up it. * Data Auto-Rebuild will be started automatically when you lock up the HDD tray.
Removing / Installing Cooling FansUnscrew the Fan door and open the door. : Be careful , the high speed rotating fans may harm you. Don't touch the rotating Fans, If necessary, Unplug the Fan power connector first.! Caution 5-6Hot SwapUnscrew Here ! Figure : Swap cooling Fan ( Unscrew )
Unplug the Fan connectorUnscrew the faulty cooling fan and replace with a good oneImportant ! The cooling fan's air flow must point to the fan door, please refer to the label on the cooling fan. Plug in the fan connector, close the fan door and screw it in ! Caution : The cooling fan will rotate immediately when you plug in the fan power connector. The Cooling Fan will only fit in one orientation.Hot SwapFigure : Swap Cooling Fan ( swap with a new Fan )5-7
A-1AppendixMicroprocessor Intel i80303 (64-bit RISC processor) Cache Memory 64MB* Maximum 512MB DRAM Slots One Module Type 144 Pin DIMM DRAM Type SDRAM DRAM Speed PC100/133 RAS access time CAS access time Parity Non-Parity Read Cache Read-Ahead Write Cache Write Back* Firmware Flash EEPROM ,256K x 8 SCSI I/O Processor LSI SYM53C896Serial Port 1x RS232 (Asynchronous) Port Ba ud Rate 115,200 (Bits Per Second) Da ta Bits 8 Sto p Bit 1 Pari ty NoneRAID Levels 0 , 1 , 0+1, 3 or 5 Data Transfer Rate Up to 80MB/s (Synchronous)SCSI ID Assignment 0 ~ 14 ( 0* )Tagged-command queuing Up to 255 simultaneous data requestsTechnical Specifications
A-2Interface : Host Channel 1* Ultra 2 LVD SCSI (68 pin) Disk Channels 4* EIDE ATA-100 Drives Hot Swap, User Replaceable Up to Four 3.5" drives ( 1" height )Maximum Fault >480 GBTolerant CapacityDrive MTBF >1,000,000 hrsHost Requirement Host IndependentOperating Systems O/S Independent and TransparentData Rebuild Automatic Data RegenerationLCD Display Panel 2 x 16 CharactersCooling Fans 6 cm Ball Bearing Fan 2 FansPower Supply Capacity 200W AC Input Voltage 115 / 230V ( +/10% ) , 60/50 HzEnvironmental Relative Humidity 10% to 85% Non-condensing Temperature Operating : 5 ~ 40 Storage : -25 ~ 60Safety testing Under apply UL, CE and FCC Class B Dimensions 165mm(W) * 295mm(D) * 280mm(H)Weight 7 kgs ( W/O Disk Drive )" * " Default Settings *** Various trademarks belong to their respective owners.Appendix

Navigation menu