Maxtronic Co FIDY Disk Array User Manual Fidy4400 Ch4
Maxtronic International Co Ltd Disk Array Fidy4400 Ch4
Contents
users manual 5
Chapter 4 : " Advanced Information " This chapter describes more information about your Disk Array. The following items are describes in detail. Memory Expansion RAID Controller Updating Firmware 4-1 Advanced Information Memory Expansion Your Disk Array comes with 64MB of memory that is expandable to a maximum of 512MB. These expansion memory module can be purchased from your dealer. Memory Type : 3.3V PC100/133 SDRAM 144pin DIMM. Memory Size : Supports 144pin DIMMs of 64MB, 128MB, 256MB or 512MB. Height : 1.15 Inches ( 29.2 mm ). 64MB 8(8Mx8), 8(4Mx16) or 4(8Mx16) 128MB 16(8Mx8), 8(16Mx8), 8(8Mx16) or 4(16Mx16) 256MB 16(16Mx8), 8(32Mx8) or 8(16Mx16) 512MB 16(32Mx8) 1.15" (29.2mm) 4-2 Advanced Information Installing Memory Modules : 1. Unscrew & Remove cover Terminal Port Host Port Unscrews Figure : Remove Cover 4-3 Advanced Information 2. Install the memory a. The DIMM memory modules will only fit in one orientation. b. Press the memory module firmly into socket from a 45 degree angle, make sure that all the contacts are aligned with the socket. c. Push the memory module forward to a horizontal position. Front Panel Figure : Controller 4-4 Advanced Information Disk Array Controller Block Diagram i960RM RISC Microprocessor Main memory Flash EPROM i960RM Local BUS NVRAM PCI Bridge LCD RS232 Terminal Port PCI BUS IEEE 1394A Dual Channel IDE Dual Channel IDE controller Controller Controller Host channel Disk Disk #1 #2 Disk Disk #3 #4 4-5 Advanced Information Updating Firmware 1. Setup your VT100 Terminal Please configure the VT100 terminal setting to the values shown below : VT100 terminal ( or compatible ) set up Connection Serial Port ( COM1 or COM2 ) Protocol RS232 ( Asynchronous ) Cabling Null-Modem cable Baud Rate 115,200 Data Bits Stop Bit Parity None 4-6 Advanced Information Setup VT100 Terminal Example : Setup VT100 Terminal in Windows Step 1. 4-7 Advanced Information Step 2. 4-8 Advanced Information Step 3. Enter a name for your Terminal. 4-9 Advanced Information Step 4. Select a connecting port in your Terminal. 4-10 Advanced Information Step 5. Port parameter settings 4-11 Advanced Information Step 6. 4-12 Advanced Information Step 7. Select emulate VT100 mode After you have finished the VT100 Terminal setup, you may restart your Disk Array and press " Ctrl + D " keys ( in your Terminal )to link the Disk Array and Terminal together. Press Ctrl to display the disk array Monitor Utility screen on your VT100 Terminal. 4-13 Advanced Information Start to Update Firmware 1. Move the cursor to " Update ROM " and press "Enter". Warning ! Unpredictable results will occur if firmware update is attempted during Host computer and Disk Array activity. All activity to the controller should be stopped before updating firmware. 4-14 Advanced Information 2. Press " Y " to download the new firmware and press " Y " again to confirm the Update. 4-15 Advanced Information 3. Select transfer " Send Text File " and press Enter. 4-16 Advanced Information 4. Locate the new Firmware file on your PC. 4-17 Advanced Information 5. Press " Go " to confirm to download the new firmware. 4-18 Advanced Information 6. Type " Go " to reconfirm and the firmware will begin to be reprogrammed. 7. After verifying, please restart the Disk Array to activate the new firmware. 4-19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 19 Create Date : 2002:05:16 09:58:44 Modify Date : 2002:05:16 09:58:44 Producer : Corel PDF Engine Version 9.397 Author : Maxtronic Creator : CorelDRAW Version 9.397 Title : Fidy4400-Ch4.cdrEXIF Metadata provided by EXIF.tools