Maytag Dv316Lg Users Manual

dv316lg 8d72494d-5863-49c7-b8a0-d11ea2db3dbc Maytag Clothes Dryer DV316LG User Guide |

2015-01-23

: Maytag Maytag-Dv316Lg-Users-Manual-269525 maytag-dv316lg-users-manual-269525 maytag pdf

Open the PDF directly: View PDF PDF.
Page Count: 98

ABS Laundry
Samsung Dryer
Model DV316LG
Maytag Technical Institute 2006 ABS-L2006-002
Notes:
SERVICE Manual
CLOTHES DRYER
Model : DV316LG
Basic Model :
Model code : DV316LGW/XAA
1. Energy Saving
2. Time Saving
3. Super Size Capacity
4. Fuzzy Algorithm
5. Easy Reversible Door
CLOTHES DRYER THE FEATURE OF PRODUCT
Samsung Electronics Co.,Ltd.
416, Maetan-3Dong, Yeongtong-Gu, Suwon City,
Gyeonggi-Do, Korea, 443-742
Printed in Korea
P/N : DC
URL : http://itself.sec.samsung.co.kr/
-This Service Manual is a property of Samsung
Electronics Co., Ltd.
Any unauthorized use of Manual can be punished
under applicable International and/or domestic
law.
CONTENTS
1. Precautions
1-1. Safety Precautions ............................................................................................................................1-1
1-2. Precautions upon Installation ............................................................................................................1-2
2. PRODUCT SPECIFICATIONS
2-1. THE FEATURE OF PRODUCT .........................................................................................................2-1
2-2. SPECIFICATIONS OF PRODUCTSPECIFICATIONS OF PRODUCT ....................................................................................................2-2
2-3. THE COMPARATIVE SPECIFICATIONS OF PRODUCT .................................................................2-3
2-4. OPTION SPECIFICATIONSSPECIFICATIONS ..............................................................................................................2-4
3. OPERATING INSTRUCTIONS AND INTALLATION
3-1. Each Key and Display .......................................................................................................................3-1
3-2. FUNCTION OF CONTROL KEYS .....................................................................................................3-2
3-3. MAIN FUNCTIONS ...........................................................................................................................3-6
3-4 SPECIAL FUNCTIONS ......................................................................................................................3-8
4. ALIGNMENT AND ADJUSTMENTS
4-1. GENERAL ERROR FUNCTION ........................................................................................................4-1
4-2. TEST MODE .....................................................................................................................................4-2
5. ASSEMBLY AND DISASSEMBLY
5-1. TOOLS FOR DISASSEMBLY AND ASSEMBLY ...............................................................................5-1
5-2. DISASSEMBLY .................................................................................................................................5-2
5-3. ASSEMBLY .......................................................................................................................................5-5
6. TROUBLE SHOOTING
6-1. TROUBLE DIAGNOSIS ....................................................................................................................6-1
6-2. PROBLEM CHECKING AND METHOD OF PCB .............................................................................6-3
6-3 Control Panel .....................................................................................................................................6-4
6-4 Driving Unit .........................................................................................................................................6-5
7. EXPLODED VIEWS AND PARTS LIST
7-1. ASSY-COVER TOP ...........................................................................................................................7-1
7-2. ASSY-TUB OUTER(SPIN BASKET) .................................................................................................7-2
7-3. ASSY-CASE OUTER .........................................................................................................................7-3
7-4. BOLT/SCREW PARTS LIST .............................................................................................................7-4
CONTENTS
8. ELECTRICAL PARTS LIST .....................................................................................................................8-1
9. BLOCK DIAGRAM ..................................................................................................................................9-1
10. WIRING DIAGRAM .............................................................................................................................10-1
11. PCB DIAGRAM .................................................................................................................................... 11-1
12. SCHEMATIC-DIAGRAMS .................................................................................................................12-1
13. CIRCUIT DESCRIPTIONS ..................................................................................................................13-1
14. REFERENCE INFORMATION
14-1. MODEL NAME ..............................................................................................................................14-1
14-2. TERMINOLOGY ............................................................................................................................14-2
14-3. FABRIC CARE CHART .................................................................................................................14-3
14-4. ELECTRICAL WARNINGS ...........................................................................................................14-4
14-5. Q & A .............................................................................................................................................14-5
1-1
41#Suhfdxwlrqv
4041#Fdxwlrq#iru#vdihw|#gxulqj#vhuylflqj
1. Do not allow the customer to repair the product.
The person may be injured or the product life may be shortened..
2. Execute A/S after unplugging the power supply unit.
Be careful of the electric shocks.
3. Do not plug several plugs in the same outlet.
It may cause a fire due to overheat.
4. Check for damage, pressing or burning of the power plug or outlet.
Replace it promptly if it has a problem.(It may cause the electric shocks or fire)
5. Do not clean the main body with water.
It may cause electric shocks and fire and shorten the product life)
6. The wiring of the harness shall be free from moisture and tightened during serving.
It shall not be deviated by certain impact.
7. Remove any dust or filth on the housing section,wiring section,connection section during servicing.
Protect from possible cause of fire such as the tracking,shortage etc.
8. Check for any marks of moisture on the electrical parts, harness section etc.
Replace the parts or remove the moisture..
9. Check the assembly status of the parts after servicing.
Maintain the status before servicing..
10. Pull out the power cord by holding the plug.
Be careful of electric shocks and when the cord is damaged.
11. Unplug the power plug from the outlet when the dryer is not used.
Be careful of electric shocks and fire due to the strike of lightning.
12. Do not use or store sprays or flammable materials(including gasoline,alcohol etc.)
around the dryer.
Be careful of explosions or fire due to electric sparks.
13. Do not put bowls of water or wet laundry on the dryer.
If water has penetrated into the dryer, this may cause electric shocks or fire.
14. Do not install the dryer where it will be exposed to bad weather.
It may cause electric shocks and fire and shorten the product life.
1-2
15. Do not push the control buttons with an awl,pin, or sharp materials.
It may cause electric shocks and damage.
16. Check the wash machine is leveled horizontally and installed properly on the floor.
The vibration may shorten the product life..
4051#Lpsruwdqw#Vdihw|#Lqirupdwlrq
To avoid risk of fire, electric shock, serious injury, or death when using your dryer, follow these basic precau-
tions:
1. Read all instructions before using dryer.
2. Install dryer according to Installation Instructions. Refer to the Grounding Instructions in the
Installation Instructions for proper grounding of the dryer.
3. Do not dry articles that have been cleaned in, washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive substances. Vapors could ignite or explode.
4. Do not use dryer to dry clothes which have traces of any flammable substance, such as vegetable oil,
cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing wax or chemicals,
such as mops and cleaning cloths. Flammable substances may cause fabric to catch fire by itself.
5. Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.
6. Do not allow children to play on or in dryer. Close supervision of children is necessary when dryer is
used near children, a safety rule for all appliances.
7. Before dryer is removed from service or discarded, remove doors to drying compartment.
8. Do not reach into dryer if cylinder is revolving.
9. Do not install or store dryer where it will be exposed to water and/or weather.
10. Do not tamper with dryer controls.
11. Do not repair or replace any part of dryer or attempt any service, unless specifically recommended in
user-maintenance instructions or in published user-repair instructions that you understand and have
skills to carry out, if you are a consumer.
12. To reduce risk of electric shock or fire, do not use extension cords or adapters to connect dryer to
electrical power source.
13. Use the dryer only for its intended purpose, drying clothes.
14. Always disconnect dryer from electrical supply before attempting any service. Disconnect power cord by
grasping the plug, not the cord.
15. Do not use heat to dry articles containing foam rubber or similarly textured rubberlike materials.
1-3
16. Always clean the lint filter after every load. A layer of lint in the filter reduces drying efficiency and pro
longs drying time.
17. Use only fabric softeners or products to eliminate static that are appropriate for automatic dryers.
18. Keep your dryer in good condition. Bumping or dropping dryer can damage safety features. If damage
occurs, have dryer checked by qualified service technician.
19. Replace worn power cords and/or loose plugs.
20. Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe
out the cylinder with a damp cloth to remove particles of fiberglass.
21. Always read and follow manufacturers instructions on packages of laundry aids. Heed all warnings or
precautions. To reduce risk of poisoning or chemical burns, keep products away from children at all times,
preferably, in a locked cabinet.
22. Never operate dryer with guards and/or panels removed.
23. Do not operate dryer with missing or broken parts.
24. Do not bypass safety devices.
25. Keep area around the exhaust opening and adjacent surrounding areas free from accumulation of
lint, dust, and dirt.
26. Interior of dryer and exhaust duct should be cleaned periodically by qualified service personnel.
27. Dryer will not operate with loading door open. DO NOT bypass door safety switch by permitting dryer to
operate with door open. Dryer will stop tumbling when door is opened. Do not use dryer if it does not stop
tumbling when door is opened or starts tumbling without pressing or turning the START mechanism.
Remove the dryer from use and call the service person.
28. Remove laundry immediately after the dryer stops.
29. ALWAYS follow the fabric care instructions supplied by the garment manufacturer.
1-4
Hohfwulfdo#Vhuylfh#Lqirupdwlrq
Electrical Dryers
- 240 VAC, 60 Hz, 30 Amps,
3-wire or 4-wire installations
Gas Dryers
- 120 VAC, 60 Hz, 15 Amps, 3wire installa-
tions
About Ground Wires
In the event of an electrical short circuit, a
ZDUQLQJ
To reduce the risk of fire, electric shock, seri-
ous injury or death, all wiring and ground-
ing must conform with the latest edition of
the National Electric Code, or the Canadian
Electrical Code, and such local regulations as
might apply. It is the customers responsibil-
ity to have the wiring and fuses checked by a
qualified electrician to make sure your home
has adequate electrical power to operate the
dryer.
ZDUQLQJ
To avoid risk of personal injury or death due
to electrical shock:
- Observe all local codes and ordinances.
- Disconnect electrical power to unit
before servicing.
- Ground appliance properly.
- Check with a qualified electrician if you
are not sure this appliance is properly
grounded.
- DO NOT ground to gas line.
- DO NOT ground to cold water pipe if
pipe is interrupted by plastic, nonmetallic
gas kets, or other insulating
(nonconducting) materials.
- DO NOT modify plug on power cord.
If plug does not fit electrical outlet, have
proper outlet installed by qualified elec
trician.
- DO NOT have a fuse in the neutral or
ground circuit. A fuse in the neutral or
ground circuit could result in an electrical
shock.
- DO NOT use an extension cord with
this appliance.
- DO NOT use an adapter plug with
this appliance.
- DO NOT pinch powe cord.
ZDUQLQJ
To reduce the risk of fire and exposure to
combustion gases, the dryer MUST be ex-
hausted to the outdoors.
DO NOT exhaust dryer air into a window well,
gas vent, chimney or enclosed, unventilated
area, such as an attic, wall, ceiling, crawl
space under a building or concealed space of
a building.
1-5
Jdv#Gu|hu#Srzhu#Vxsso|
This equipment MUST be grounded. In the
event of an electrical short circuit, grounding
reduces the risk of electric shock by providing
an escape wire for the electrical current. This
unit is equipped with a cord having a ground-
ing wire with a grounding plug. The plug must
be plugged into an outlet that is properly
installed and grounded.
Consult a qualified electrician or servicer if
grounding instructions are not completely un-
derstood, or if doubt exists as to whether the
equipment is properly grounded.
Do not use an extension cord. If the prod-
uct power cord is too short, have a qualified
electrician install a three  slot receptacle.
This unit should be plugged into a separate 60
hertz circuit with the electrical rating as shown
on the serial plate.
Surshu#Jurxqglqj#dqg#Srodul}dwlrq#iru#453#
YrowvZdoo#Rxwohwv
For the safety of our customers and the serv-
ice technician ALL gas dryers have a three!!
prong power cord and MUST be connected to
a properly polarized and grounded wall outlet.
This information was written for those who do
not understand grounding and polarization
of a wall outlet. A 120 VAC wall outlet must
always be wired as shown below.
Srodul}dwlrq-This means that the larger slot
must be neutral and the small slot must be hot
(live).
Plvsrodul}hg-The outlet is miswired so that the
larger slot is hot (live) and the smaller slot is
neutral.
Jurxqghg -This means the round hole con-
nection is connected to ground through a
connection to the main power panel.
Xqjurxqghg-The round hole connection is not
connected to a ground and/or the main power
panel.
Jdv#Frqqhfwlrq#Lqirupdwlrq
ZDUQLQJ
To avoid death, personal injury or property
damage, from fire or explosion, information
in this manual must be followed exactly.
Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
ZKDW#WR#GR#LI#\RX#VPHOO#JDV
- Do not try to light any appliance.
- Do not touch any electrical switch; do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli
er’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
ZDUQLQJ
To reduce the risk of fire and exposure to
combustion gases, the dryer MUST be ex-
hausted to the outdoors.
DO NOT exhaust dryer air into a window well,
gas vent, chimney or enclosed, unventilated
area, such as an attic, wall, ceiling, crawl
space under a building or concealed space of
a building.
1-6
Adjustable
Door
Control
panel
Tools needed for installation
Proper installation is the owner’s responsibility.
HOWEVER, SERVICE CALLS PERFORMED AS A RESULT OF POOR SET-UP, ADJUSTMENT, AND CONNECTION ARE THE
RESPONSIBILITY OF THE INSTALLER.
Make sure you have everything necessary for proper installation.
1. GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.
2. POWER CORD for electric dryers (except Canada).
3. GAS LINES (if a gas dryer) must meet national and local codes.
4. EXHAUST SYSTEM – must be rigid metal or fl exible stiffwalled metal exhaust ducting.
See Exhaust Requirements.
Adjustable leg
Pliers Cutting knife Pipe wrench
(gas only) Nut drivers
Level Screwdriver
(standard) Duct tape Crescent
spanner
4061#Suhfdxwlrqv#xsrq#Lqvwdoodwlrq
1-7
DUCTING REQUIREMENTS
• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.
• Do not use a smaller duct.
• Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation.
Lint accumulation should be cleaned regularly.
• If a fl exible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a fl exible
duct with a thin foil wall. Serious blockage can result if the fl exible metal duct is bent too sharply.
• Never install any type of fl exible duct in walls, ceilings, or other concealed spaces.
• Keep exhaust duct as straight and short as possible.
• Secure joints with duct tape. Do not use screws.
• DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF A
BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY.
THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.
• Plastic fl exible duct can kink, sag, be punctured, reduce airfl ow, extend drying times, and affect dryer
operation.
• Exhaust systems longer than recommended can extend drying times, affect machine operation, and may collect lint.
• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts
and entry of wildlife. Never use an exhaust hood with a magnetic damper.
• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and
the ground or other obstruction. The hood opening should point down.
• Never install a screen over the exhaust outlet.
• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a
house or porch.
• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope
slightly down towards the exhaust hood to reduce condensation and lint buildup.
• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord
before cleaning.
• Check frequently to be sure the exhaust hood damper opens and closes freely.
ELECTRIC AND GAS DRYER
Weather Hood Type
Recommended Use only for short-run installation
No. of 90°
elbows Rigid Metallic Flexible* Rigid Metallic Flexible*
0 24.4 m (80 ft.) 12.4 m (41 ft.) 22.6 m (74 ft.) 10.1 m (33 ft.)
1 20.7 m (68 ft.) 11.2 m (37 ft.) 18.9 m(62 ft.) 8.8 m (29 ft.)
2 17.4 m (57 ft.) 10.1 m (33 ft.) 15.5 m(51 ft.) 7.6 m (25 ft.)
3 14.3m (47 ft.) 9.0 m (29 ft.) 12.5 m(41 ft.) 6.5 m (21 ft.)
* Do not use non-metallic fl exible duct.
4” (10 .16 cm) 2.5” (6.35 cm)
1-8
If new dryer is installed into an existing exhaust system you must make sure:
• The exhaust system meets all local, state, and national codes.
• That fl exible plastic duct is not used.
• Inspect and clean all lint buildup from inside the existing duct.
• The duct is not kinked or crushed.
• The exhaust hood damper opens and closes freely.
The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
This can be measured with the dryer running with a manometer at the point where the exhaust duct connects
to the dryer. A no-heat setting should be used. The dryer tumbler shoul
REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD
SUFFOCATING.
LOCATION CONSIDERATIONS
The dryer should be located where there is enough space in front for loading the dryer, and enough space
behind for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or the
left, use the accessory exhaust kit. Instructions are included with the kit. It’s important to make sure the room
has enough fresh air. The dryer must be located where there is no air-fl ow obstruction.
On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air for
combustion and proper dryer operation.
THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO
WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR OF COMBUSTIBLE MATERIALS,
GASOLINE, AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE
LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT LINT-FREE.
ALCOVE OR CLOSET INSTALLATION
WARNING – The dryer must be exhausted to the outside to reduce the risk of fi re when
installed in an alcove or closet.
• No other fuel-burning appliance should be installed in the same closet as the dryer.
• WARNING: To reduce the risk of fi re, this dryer MUST BE EXHAUSTED TO THE OUTDOORS.
See EXHAUST INFORMATION section.
• Minimum clearances between the dryer and adjacent walls or other surfaces are: 2” in front,
17” on top, 1” on either side, and 2.375” in the back.
• Closet front must have two unobstructed air openings for a combined minimum total area of
72 in² with 3” minimum clearance on the top and bottom. A louvered door with equivalent space
clearance is acceptable.
1-9
MOBILE HOME INSTALLATION
The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and
Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).
When installing a dryer in a mobile home, provisions for anchoring the dryer to the fl oor must be made.
Locate in an area that has adequate fresh air.
A minimum of 72 in² (183 cm² ) of unobstructed space is required.
All mobile home installations must be exhausted to the outside with the exhaust duct termination securely
fastened to the mobile home structure, using materials that will not support combustion.
The exhaust duct may not terminate underneath the mobile home.
See Exhausting section for more information.
EXHAUSTING
Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown
into the room.
In the United States:
• All dryers must be exhausted to the outside.
• Only rigid or fl exible metal duct should be used for exhausting.
In Canada:
• All dryers must be exhausted to the outside.
Outside the U.S. and Canada:
• Refer to local codes.
WARNING –The dryer must be exhausted to the outside to reduce the risk of fi re when installed
n an alcove or closet.
NEVER USE PLASTIC OR NON-METAL FLEXIBLE DUCT.
If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.
Use only metal exhaust duct that is non-fl ammable to ensure containment of
exhaust air, heat, and lint.
1-10
GAS REQUIREMENTS
Use only natural or LP (liquid propane) gases.
THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL
CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED
STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).
Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP
(liquid propane) gas, it must be converted for safe and proper performance by a qualifi ed service technician.
A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line
on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off valve
be installed within 6’ of your dryer.
Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the fl oor.
Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge
connection, must be installed immediately upstream of your dryer’s gas supply connection.
Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the
system.
DO NOT reuse old fl exible metal gas lines. Flexible gas lines must be design certifi ed by the American Gas
Association (CGA in Canada).
NOTE: • Any pipe joint compound used must be resistant to the action of any liquefi ed petroleum gas.
• As a courtesy, most local gas utilities will inspect a gas appliance installation.
GAS IGNITION – Your dryer uses an automatic ignition system to ignite the burner.
There is no constant burning pilot.
COMMONWEALTH OF MASSACHUSETTS INSTALLATION INSTRUCTIONS
Your dryer must be installed by a licensed plumber or gas fi tter. A “T” handle manual gas valve must be
installed in the gas supply line to your dryer. If a fl exible gas connector is used to install your dryer, the
connector must have a maximum length of 3’ (36”).
WARNING – Gas leaks may occur in your system, creating a dangerous situation.
Gas leaks may not be detected by smell alone.
Gas suppliers recommend you purchase and install a UL-approved gas detector.
Install and use in accordance with manufacturer’s instructions.
1-11
ELECTRICAL REQUIREMENTS
NOTE: Wiring diagram is located on plate below the control panel.
WARNING –
• Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check
with a qualifi ed electrician or serviceman if you are in doubt as to whether your dryer is properly
grounded. Do not modify the plug provided with your dryer – if it doesn’t fi t the outlet, have a proper
outlet installed by a qualifi ed electrician.
• To prevent unnecessary risk of fi re, electrical shock, or personal injury, all wiring and grounding must be
done in accordance with local codes, or in the absence of local codes, with the National Electrical Code,
ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest
Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical services
for your dryer.
• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Lastest
Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and local
codes and ordinances.
GROUNDING
This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of
electrical shock by providing a path of least resistance for electrical current.
GAS MODELS
Your dryer has a cord with an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided with your dryer – if it doesn’t fi t the outlet, have a proper outlet installed
by a qualifi ed electrician.
NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT WATER
PIPES.
ELECTRIC MODELS
Your dryer has a cord with an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected
to a permanent grounded metal wiring system, or an equipment grounding conductor must be run with
the circuit conductors and connected to the equipment grounding terminal.
1-12
ELECTRICAL CONNE CTIONS
Before operating or testing, follow all grounding instructions in the Grounding section.
An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN
EXTENSION CORD.
GAS MODELS – U.S. and Canada
A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required.
ELECTRIC MODELS – U.S. Only
Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require 120/208
volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label
located behind the door. A 30-ampere fuse or circuit breaker on both sides of the line is required.
• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.
• The power cord is NOT provided with U.S. electric model dryers.
IMPORTANT:
When local codes allow, the dryer electrical supply may be connected by means of a new power supply
cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240 volts, 30-
ampere with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade
lugs with turned up ends, or with tinned leads.
1. size of the conductors and the type of cord.
2. 3/4” (1.9 cm) UL-listed strain relief
• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be
retained at the dryer cabinet with a suitable UL-listed strain relief.
• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,
(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding
through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA type 14-30R.)
ELECTRIC MODELS – Canada Only
• A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker
on both sides of the line is required.
• All Canadian models are shipped with the power cord attached. The power cord should be plugged into
a 30-ampere receptacle.
NOTE: It is not permissible to convert a dryer in Canada to 208 volts.
REPLACEMENT PARTS AND ACCESSORIES
If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your
dryer or a SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).
1-13
INSTALLATION
Parts and literature are packaged inside your dryer drum. To install:
1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-by-side, to allow access to
gas, electrical, and exhaust connections.
Lay two of the carton cushion-tops on the fl oor. Tip your dryer on its side so it will lay across both cushion-tops.
2. Set your dryer back in an upright position.
3. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer to the exhaust hood. The
crimped end of the duct sections must point away from your dryer.
DO NOT use sheet metal screws when assembling ducting. These joints should be taped.
Never use plastic fl exible exhaust material.
Tip for tight installations: install a section of exhaust system to your dryer before putting it in place.
Use duct tape to secure this section to your dryer, but do not cover louvers in dryer cabinet.
4. Review Electrical Requirements section.
BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.
U.S. MODELS:
IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION.
The dryer frame is grounded to the neutral conductor at the terminal block.
A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes,
or if local codes do not permit grounding through neutral. If the 4-wire system is used, the dryer frame cannot be grounded to the
neutral conductor at the terminal block. Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.
Remove the terminal block cover plate.
Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block.
NOTE: A strain relief must be used.
Do not loosen the nuts already installed on the terminal block. Be sure they are tight.
Use a 3/8” (1cm) deep well socket.
5. Review Gas Requirements section.
Remove the pipe thread protective cap.
Apply pipe joint compound or about 1 1/2 wraps of Tefl on tape over all threaded connections.
NOTE: Pipe joint compound must be resistant to the action of any liquefi ed petroleum gas.
Connect the gas supply to your dryer.
An additional fi tting is required to connect the 3/4” (1.9 cm) female thread end of a fl exible connector to the 3/8” (1 cm) male
threaded end on the dryer.
Securely tighten the gas line fi tting over threads.
Turn on the gas supply. Check all gas connections for leaks using a soap solution.
If bubbles appear, tighten the connections and recheck.
DO NOT use an open fl ame to check for gas leaks.
1-14
3-WIRE SYSTEM CONNECTIONS
1. Loosen or remove center terminal block screw.
2. Connect neutral wire (white or center wire) of the power cord to the center, silver-colored
terminal screw of the terminal block. Tighten screw.
3. Connect the other wires to outer terminal block screws. Tighten screws.
4. Tighten strain relief screws.
5. Insert tab of terminal block cover into your dryer’s rear panel slot.
Secure cover with hold-down screw.
• External ground connector
• Neutral grounding wire (green/yellow)
• Center silver-colored terminal block screw
• Neutral wire (white or center wire)
• 3/4” (1.9 cm) UL-listed strain relief
WARNING: If converting from a 4-wire electrical system to a 3-wire, the ground strap must be
reconnected to the terminal block support to ground the dryer frame to the neutral conductor.
4-WIRE SYSTEM CONNECTIONS
1. Remove center terminal block screw.
2. Connect ground wire (green or unwrapped) of power cord to external ground conductor screw.
3. Connect neutral wire (white or center wire) of power cord and appliance ground wire (green
with yellow stripes) under central screw of the terminal block.
4. Connect the other wires to outer terminal block screws. Tighten screws.
5. Tighten strain relief screws.
6. Insert tab of terminal block cover into your dryer’s rear panel slot.
Secure cover with hold-down screw.
• External ground connector
• Green or bare copper wire of power cord
• 3/4 in. (1.9 cm) UL-listed strain relief
• Center silver-colored terminal block screw
• Grounding wire (green/yellow)
• Neutral wire (white or center wire)
6. With a level, check your dryer and make necessary adjustments to the leveling legs.
7. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are
complete. Plug in your dryer, and check operation by using the checklist below.
8. (GAS MODELS ONLY)
The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat
setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait
5 minutes. Be sure the gas supply to your dryer has been turned on. In order to confi rm gas ignition,
check the exhaust for heat.
FINAL INSTALLATION CHECKLIST
□ Dryer is plugged into electrical outlet and properly grounded.
□ Exhaust ductwork is hooked up and joints taped.
□ Plastic fl exible duct is NOT used.
□ Use rigid or stiff-walled fl exible metal vent material.
□ Dryer is level with all legs fi rmly on the fl oor.
□ Gas models – gas is turned on with no gas leaks.
□ Start your dryer to confi rm that it runs, heats, and shuts off.
1-15
Dryer Exhaust Tips
WARNING: Plastic or non-metal fl exible duct presents a potential fi re hazard.
1. Let your dryer exhaust the air easily.
2. Use 4” diameter rigid metal duct.Tape all joints, including at the dryer.
Never use lint-trapping screws.
3. Keep ducts as straight as possible.
4. Clean all old ducts before installing your new dryer.
Be sure vent fl ap opens and closes freely.
Inspect and clean the exhaust system annually.
Don’t let a poor exhaust system slow drying by:
1. Restricting your dryer with a poor exhaust system.
2. Using a plastic, thin foil, or non-metal fl exible duct.
3. Using unnecessarily long duct runs with many elbows.
4. Allowing crushed or clogged ducts and vent.
1-16
1. Unplug power cord.
2. Remove two door hinge
screws.
3. Lift the door and remove
from
dryer.
6. Place the door on the other
side and reattach it to dryer.
4. Remove two screws on the
opposite side of door hinge. 7. Reassemble holder lever.
5. Remove two screws on holder
lever.
8. Reassemble the screws in
the
remaining holes.
Door Reversal
2-1
2. PRODUCT SPECIFICATIONS
2-1. THE FEATURE OF PRODUCT
2-2
5051#VSHFLILFDWLRQV#RI#SURGXFW
ZDVK#W\SH FRONT LOADING TYPE
GLPHQVLRQ
Div Inches (cm) Div Inches (cm)
A. Height 38”(96.5) C. Depth with
door open 90° 49”(124.5)
B. Width 27”(68.6) D. Depth 30.25” (77.0)
ZHLJKW 56.8kg
KHDWHU#UDWLQJ 5300W
SRZHU#FRQVXPSWLRQ
NO HEAT 268W
HEATING 5445W
2-3
5061#RYHUYLHZ#RI#WKH#GU\HU
3-1
61#RSHUUDWLQJ#LQVWDOODWLRQV#DQG#LQVWDOODWLRQ
6041#RYHUYLHZ#RI#WKH#FRQWURO#SDQHO
1. Digital Graphic Display
The display window shows the estimated time remaining in the cycle after the Cycle Selector dial is
pressed. The estimated time remaining may fl uctuate as the cycle progresses.
The Drying light will illuminate and remain lit until the cycle is complete.
When your dryer is in the cool-down phase, the Cooling light will illuminate.
When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate.
When the cycle is complete, “END” will appear in the display panel until the dryer door is opened or
Power key is pushed.
If your dryer is paused during a cycle, the indicator lights will blink until the Cycle Selector dial is
pressed.
2. Dry Level Selection Button
To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the Dry Level
button. An indicator light will illuminate next to the desired dryness level.
Press the button repeatedly to scroll through the settings. Larger or bulkier loads may require the
Very Dry (select models) or More Dry setting for complete dryness.
The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing
at the end of the cycle. Damp Dry (select models) is designed to partially dry items.
Use for items that lay fl at or hang to dry.
3. Temp Selection Button
To select the correct temperature for the load, press the Temp button. An indicator light will
illuminate next to the desired temperature. Press the button repeatedly to scroll through the
settings.
High – For sturdy cottons or those labeled Tumble Dry.
Medium – For permanent press, synthetics, lightweight cottons, or items labeled Tumble Dry Medium.
Medium Low – For lower heat than Medium to dry synthetic or washable knit fabrics.
Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.
Extra Low – Provides the lowest heated dry temperature possible.
4. Time Selection Button
When using Manual Dry cycles, time can be adjusted by pressing time selection button.
During the Sensory Dry cycle, the time light indicator is off because exact drying times are
determined by fl uctuating humidity levels.
3-2
5. Signal Selection Button
When the cycle is complete, a chime will sound.
When the Wrinkle Prevent option is selected, the chime will sound intermittently.
Adjust the volume of the chime or turn it off by pressing the Signal button.
Press the button repeatedly to scroll through the choices.
6. Wrinkle Prevent Selection Button
Wrinkle Prevent provides approximately 90 minutes of intermittent tumbling in unheated air at the
end of the cycle to reduce wrinkling. Press the Wrinkle Prevent button to activate this feature.
The indicator light above the pad will illuminate when Wrinkle Prevent is selected.
Chasing lights appear in the display when the Wrinkle Prevent option is selected. The load is dry, and
can be removed at any time during the Wrinkle Prevent cycle.
7. Select Cycle Option
Adjust Time – Time can be added or subtracted from the automatically set times in the Manual
Dry cycles (Time Dry, Freshen Up, Delicates, Wrinkle Release, or Air Fluff cycles).
To add or subtract time from the cycle, press the Adjust Time arrow pad up or down until the desired
time is displayed.
My Cycle – Choose your favorite cycle including cycle, temp, dry level option, etc.
Rack Dry – Rack Dry is available at Time Dry cycle. Temperature will be set only to Extra Low.
8. Cycle Selector
To select a cycle, rotate the Cycle Selector dial to the desired cycle.
The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Towels, Perm Press and
Delicates cycles are Sensor Dry cycles.
Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected
dryness level (very dry to damp dry) is reached.
Normal – Dry loads such as cotton, underwear, and linens use this cycle to get various levels of heat
for drying.
Heavy Duty – Use this cycle to get high heat for heavy fabrics such as jeans, corduroys, or work
clothes.
Towels – Dry loads such as bath towels.
Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent press fabrics
automatically. The cycle minimizes wrinkling by providing a longer unheated cool-down
period at the end of the cycle.
Delicates – The Delicates cycle is designed to dry heat-sensitive items at a low drying temperature.
Freshen Up – This cycle removes odors and freshens garments.
Time Dry – Time Dry allows you to select the desired cycle time in minutes.
Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow to set the drying time.
Press the arrow repeatedly to scroll through the time settings.
Wrinkle Release – The Wrinkle Release cycle will release wrinkles from items that are clean, dry,
and only slightly wrinkled, such as clothes from a crowded closet, suitcase or items that have been
in the dryer too long after the cycle has ended. Wrinkle Release can be used with any temperature
selection.
Air Fluff – The Air Fluff cycle tumbles the load in room temperature air.
9. Start/Pause Selection Button
Press to pause and restart programs.
10. Power Button
Press once to turn your dryer on, press again to turn it off. If your dryer is left on for more than 10
minutes without any buttons being touched, the power automatically turns off.
3-3
6051#F\FOH#FKDUW
Cycle
Default Drying Cooling Wrinkle
prevent
Temp con-
trol
Sensor dry
level Time Time Time Time
Sensor
Dry
Normal High
(Medium) Normal dry 44 min 39 min 5 min 90 min
Heavy
Duty
High (No
change) Normal dry 60 min 55 min 5 min 90 min
Towels High (Me-
dium) Normal dry 52 min 47 min 5 min 90 min
Perm Press
Medium
Low
(No change)
Normal dry 34 min 24 min 10 min 90 min
Delicates Low (No
change) Normal dry 29 min 24 min 5 min 90 min
Extra
Delicates
Extra Low
(No change) Normal dry 29 min 24 min 5 min 90 min
Manual
Dry
Freshen Up High (No
change) - 30 min 25 min 5 min -
Time Dry High - 40 min 35 min 5 min -
Wrinkle
Release Medium - 25 min 20 min 5 min -
Air Fluff - (No
change) - 20 min - 20 min -
Quick Dry High - 30 min 25 min 5 min -
3-4
6061#PDLQ#IXQFWLRQ
CHILD LOCK
A function to prevent children from playing with your dryer.
SETTING/RELEASING
If you want to set or release Child Lock, press both the Time and Signal buttons at the same time for 3
seconds.
How to Set:
1. It can be set while your dryer is running.
2. Once you set the Child Lock function, no button, except for the Power button,
can be controlled until you release the Child Lock function.
3. The Child Lock indicator will be lit.
Notice:
1. If the power is on again, the Child Lock function remains unchanged.
2. To release that function, follow the instructions above.
Notice:
When other buttons, except for the Power button, do not respond, check the Child Lock indicator.
MY CYCLE
Lets you activate your customized cycle that includes Dry Level, Temp, Time option, etc.
By pushing the My Cycle button, you activate the settings used during the previous My Cycle mode.
(Default : Normal Cycle)
If My Cycle mode is activated, My Cycle button will be lit.
You can select all options in My Cycle mode as follows.
1. Select cycle using Cycle Selector dial.
2. After cycle selection, set each option.
Note: At this time, the option will follow as per each cycle’s default option selection.
Then you can start My Cycle by pushing the Start/Pause button in My Cycle mode.
The cycle and options you select will be displayed next time you choose My Cycle.
3-5
Rack Dry
INSTALLING THE DRYING RACK
1. Open dryer door.
2. Position drying rack in tumbler, placing the rear legs in the two recessed areas of the dryer’s
back wall.
3. Place the front lip of the drying rack on top of the lint fi lter.
4. Place items to be dried on the rack, leaving space between them so air can reach all surfaces.
5. Close dryer door.
6. Use the Time Dry cycle. Select time according to moisture and weight of the items. Start dryer.
It may be necessary to reset the timer if a longer drying time is needed.
SUGGESTED ITEMS SUGGESTED TEMP. SETTINGS
Washable sweaters (block to
shape and lay fl at on rack) Heat (Low/Extra Low)
Stuffed toys (cotton or
polyester fi berfi lled) Heat (Low/Extra Low)
Stuffed toys (foam or
rubber-fi lled) Air Fluff
Foam rubber pillows Air Fluff
Sneakers Fluff or Heat
WARNING – Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the item
and lead to a fi re hazard.
3-12
Memo
4-1
71#DOLJQPHQW#DQG#DGMXVWPHQWV
7041#Huuru#lwhpv#dqg#Gldjqrvwlf#Frghv
1. An occurrence of an Error will make a sound of error melody for 5sec and continuously show one of the
Error Displays from the following errors.
Display Description Trigger Action Taken
tS Dryer Thermistor Short
Sensed
The Thermistor
resistance is
very low.
Check for:
- Clogged lint screen.
- Restricted vent sys-
tem.
- Check Thermistor
resistance.
tO Dryer Thermistor Open
Sensed
The Thermistor
resistance is
very high.
Check for:
- Clogged lint screen.
- Restricted vent sys-
tem.
- Check Thermistor
resistance.
do Door Open
Running the
dryer with door
open
Check for:
- Close the door, and
run the dryer
- Loose or open wire
terminals in Door
Sense circuit.
FE Power source frequen-
cy Error
Invalid power
source
Frequency
Check for:
- Not using regular
power source
frequency
- Invalid power fre-
quency sense circuit
dF Door Circuit Failure
Invalid state for more
than 256
milliseconds
Check for:
- Loose or open wire
terminals in Door
Sense circuit.
hE Heater Error Invalid heating Temp in
running the dryer
Check for:
- Restricted vent sys-
tem.
- Check Thermistor
resistance.
bE Button Error
Invalid state
of key circuit short
for 75secs
Check for:
- Display PCB key
circuit short or not
od Over Dry
Invalid Dry
time in
excess Dry time
Check for:
- Sensor bar Open
- using Adjust time Up
excessively
Et EEprom Fail
Invalid state
of Eeprom
communication
Check for
- PCB on EEprom
circuit
4-2
7051#WHVW#PRGH
Continuous Run Mode:
1. Press Signal + Dryness Level for 3 sec during Power On State (Normal User Mode) .
2. Once in Continuous Run Mode, 7-Segment will toggle display “cc” and the remaining time.
3. The previous cycle will restart during Continuous Run Mode until continuous run mode is
disabled.
4. During Continuous Run Mode, press Signal + Dryness Level for 3 seconds to return to normal
user mode. 7-segment will no long display “cc” and only display the remaining time.
4-2-1. Continuous Run Mode
4-2-2. Special Test Mode
Defi nition of Special Test Mode:
- Dryer must be on before Service Mode can be entered.
- Press Signal and Temp Keys for 3 seconds, or until 3 beeps are heard.
- The machine will now be in Service Mode.
- Upon entry into Service Mode, the Sensor Bar Touch Data will be shown (Default Special Test Mode).
How to Enter:
- To enter Special Test Mode press Signal and Temp Keys for 3 seconds for 3 seconds or until the control
beep.
(same for all Frontier models.)
4-3
4-2-3. Sensor Bar Touch Data Mode
Defi nition of Sensor Bar Touch Data Mode:
-While in Power On pressing Signal and Temp Keys for 3 seconds
-This action will put the dryer into sensor bar touch data mode
- Dryer will display Sensor Bar data. This mode is default mode of entering service mode
How to Enter:
- While in Power off pressing Signal and Temp Keys for 3 seconds (same for all Frontier models.)
4-2-4. Cycle Count Mode
Defi nition of Cycle Count Mode:
- While in Service Mode pressing the Signal key will put the dryer into the cycle count mode
- Cycle number executed will display.
How to Enter:
- To enter Special Test Mode press While in Service Mode pressing the Signal key for 3 seconds or until
the control beep.
(same for all Frontier models.)
4-4
4-2-5. Software Version Mode
Defi nition of Software Version Mode:
- While in Service Mode pressing the Temp key will put the dryer into the software version mode
How to Enter:
- To enter Special Test Mode press Temp Key until the control beep.
(same for all Frontier models.)
ex) In case of “U105”, U0 means major version “v1“ 05 means minor version “05”
4-2-6. System Check Mode
Special Test Mode:
- While in Power Off, pressing the Dryness Level + Power keys simultaneously will put the dryer into the
System Check mode
- “ t2 “ will display.
- System Check Mode Progress
t2 mode Function Performed Start/Pause Motor(CW) Relay On → Heater Relay On → Heater Relay Off →
Motor(CW) Relay Off (Circulation)
5-1
81#DVVHPEO\#DQG#GLVDVVHPEO\
8041#WRROV#IRU#GLVDVVHPEO\#DQG#DVVHPEO\
NO. TOOL
1Box driver 10mm
13mm
19mm
Heater (1)
Motor (1), Balance (5), 2 holes of each left and right of the
shock absorber 1 Pulley hole
2Double-ended
spanner 10, 13,19mm Replaceable for the box driver.
Since the bolt runs idle when the box driver is used, use the
box driver 17mm.
3 Vice pliers Tool to protect the idle and abrasion of the bolt for the
box driver.
4 Other(Driver, Nipper, Long nose) General tools for the after service.
5 JIG for the Tub 1 (Disassemble and Assemble)
######
5-2
Part Name Descriptive Picture How To Do
Top
Removal
Drum Baffl e
Removal
Console
Removal
####
5-2. DISASSEMBLY
Warning! To avoid risk of electrical shock, personal injury or death, disconnect the power to the washing machine.
1.Disconnect power supply to unit.
2.Remove 2 10mm screws from
dryer back.
3.Slide Top Cover towards the rear
and lift from unit.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove four screws located at
the sound dampening seem.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove two screws mounting
the Heater PCB Board.
4.Disconnect the black and white
connectors.
5.Remove four screws attaching
Console to dryer
6.Rotate Console down and
remove from dryer.
5-3
Part Name Descriptive Picture How To Do
Front Panel
Removal
Front Bulk-
head
Removal
Moisture
Sensor
Removal
####
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove four screws attaching
Front Panel to dryer.
5.Remove two screws in the door
area.
6.Pull Front Panel forward and
disconnect the Interior Light
harness.
7.Lift the Front Panel off the three
tabs across the bottom and
remove.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove Front Panel.
5.Remove screws retaining
Console Back Cover.
6. Disconnect Interior Light wiring
harness.
7.Disconnect Moisture Sensor
wiring harness.
8.Remove four Bulkhead retaining
screws.
9.Lift Bulkhead from Cabinet and
remove.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove Front Panel.
5.Disconnect Moisture Sensor wire
harness.
6.Remove sensor attachment
screw.
5-4
Part Name Descriptive Picture How To Do
Drum Re-
moval
Rear Roller
Removal
Motor/Blow-
er
Assembly
Removal
(1)
####
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove Front Panel.
5.Remove Console Back Cover.
6.Remove Front Bulkhead.
7.Remove belt from Idler Pulley.
8.Grasp the Drum with one hand
and the belt with the other. Lift
the Drum and slide out the front.
Carefully spread the cabinet as
needed to gain additional
clearance.
1.Disconnect power supply to unit.
2.Remove Rear Bulkhead.
3.Remove Roller Keeper and nut.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove Front Panel.
5.Remove Console Back Cover.
6.Remove Belt from Idler Pulley.
7.Remove Drum.
8.Remove the two screws securing
the Blower Intake Panel to the
Blower Housing. Remove Blower
Intake panel.
9.Removed the screw at the
bottom of the blower housing.
10.Remove the blower attachment
screw under the Thermistor.
11.Remove two screws attaching
the motor bracket to the base.
12.Disconnect the Motor wire
harness and the two wires to the
belt switch.
5-5
Part Name Descriptive Picture How To Do
Motor/Blow-
er
Assembly
Removal
(2)
Rear Bulk-
head
Removal
Burner Re-
moval
Heater As-
sembly
Removal
####
13.Slide the Motor Blower.
Assembly toward the heater and
lift to disengage the tabs on the motor
from the slots in the base.
14.Remove the 14mm nut securing the blower
wheel to the shaft. The nut is a left hand
thread.
QRWH=#D#zuhqfk#fdq#eh#sodfhg#rq#erwk##
# # hqgv#ri#wkh#Prwru#Rxwsxw#Vkdiw1
15.Remove Blower Wheel.
16.Remove the three screws
securing the blower housing to
the motor bracket.
17.Remove the three screws
securing the blower housing to
the motor bracket .
18.Use a wide blade screwdriver to pop off the
motor retentionclamps.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove Front Panel.
5.Remove Console Back Cover.
6.Remove Belt from Idler Pulley.
7.Remove Drum.
8.Remove 7 screws from the back.
9.Lift the rear bulkhead off the right
and left side hangers.
1.Disconnect power supply to unit.
2.Shut off gas supply.
3.Disconnect gas line.
4.Remove two screws securing
burner to bracket.
QRWH=#Wkh#Ljqlwhu#Edu#lv#iudjloh1#Eh#
# # fduhixo#qrw#wr#gdpdjh#Ljqlwhu#zkhq##
# # uhprylqj#Exuqhu#Dvvhpeo|1
5.Remove the two screws attaching
the housing to the burner bracket.
The screws are recessed from view.
6.Slide Burner Assembly from dryer.
1.Disconnect power supply to unit.
2.Remove Top Cover.
3.Remove Console.
4.Remove Front Cover.
5.Remove Heater Assembly retaining screw.
6.Slide Heater Assembly out the front of dryer.
7.Remove the wiring terminals from the Heater
Assembly.
8.Reinstall by aligning the tabs on the back
bulkhead with the notches in the Heater As
sembly.
5-6
5-3. REASSEMBLY
Reassembly procedures are in the reverse order of dissasembly procedures.
6-1
91#WURXEOH#VKRRWLQJ
9041#WURXEOH#GLDJQRVLV
- As the micom dry machine is confi gured of the complicate structure, there might be the
service call.
Below information is prepared for exact trouble diagnosis and suitable repair guide.
Caution for the Repair and Replacement
Please follow below instruction for the trouble diagnosis and parts replacement.
1) As some electronic components are damaged by the charged static electricity from the resin
part of wash machine or the human body, prepare the human body earth or remove the potential differ
ence of the human body and wash machine by contacting the power supply plug when the work contact
ing to PCB is executed.
2) Since AC220~240V is applied to the triac T1 and T2 on P.C.B, the electric shock may occur by
touching and be careful that the strong and weak electricity are mixed.
3) As the P.C.B assembly is designed for no trouble, do not replace the P.C.B assembly by the
wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not op
erated normally.
6-2
No Problem What To Do
1
Will Not Start or Run
• All wires are hooked up to their corresponding terminals.
• Dryer is plugged in.
• Blown fuse or circuit breaker.
• Door switch functional...door closed. Check for error code 3 (See Table for code
defi nition).
• Start/Pause rotary selector dial functional.
• Control Board operational.
• Belt off or broken and Belt Cut-off Switch operates.
• Drive motor functional.
• Check motor winding resistance: 2.88ohms between pin #3 and 4, 3.5ohms
between pin #4 and 5.
2 Motor runs/ tumbler will not turn • Belt off or broken/damaged.
• Idler tension spring too weak or stretched.
• Idler pulley jammed or stuck.
3Runs a few minutes and then
stops
• Lint buildup around drive motor.
• Low voltage present.
• Blower impeller blocked in blower housing.
• Drive motor - start switch contacts stuck closed.
4Blows fuses or trips circuit
breaker
- Is the belt connected well?
- Is the winding of the motor continuous?
(Rotor winding, stator winding, generator)
- Is the motor protector normal?
• If above points are not found, the PCB assembly is out of order.
Replace it.
5Blows fuses or trips circuit
breaker
(Gas Model)
• During ignition the dryer will draw X amps. With the burner ON, the dryer will
draw X amps. If the dryer is drawing amperages above this, then the house
wiring, fuse box or circuit breaker is suspected to be at fault.
• Igniter harness loose and shorted to base.
• Incorrect wiring or wire shorted to ground.
• Drive motor winding shorting to ground.
6 Will not heat (motor runs)
Open heating element.
• Hi-Limit trips easily or is open.
• Regulating thermostat trips easily or is open.
• Membrane switch open.
• Check Thermistor.
7Will Not Dry Gas Model
Poor Gas Ignition
When the dryer is operated on a heat setting, the igniter should be energized and
burner shall fi re within 45 seconds at 120 VAC. The failure of a component in this
system will usually be indicated by one of three symptoms:
8 The igniter does not glow
If the igniter does not heat up, remove power and using an ohmmeter, check the
following:
• Open fl ame sensor
• Open igniter
• Shorted booster coil
• Open wiring
• Bad motor switch ( Neutral supply)
• No power from control ( L1 supply)
9 Igniter glows - No gas ignition
If the igniter heats up but the main burner fl ame is not ignited, remove power and
using an ohmmeter, check the following:
• Open secondary coil
• Open holding coil
• Open wire harness
• Stuck fl ame sensor (Stuck closed)
10 The gas is ignited but the fl ame
goes out
If a normal ignition takes place and after a short while the fl ame goes out, check
for the following:
• Radiant sensor contacts opening prematurely.
• Weak gas valve coil may open when stressed by higher Temps.
• Weak Hi-Limit
• Poor venting
• Bad drum seals
11
Improper drying
clothes wrinkled
Rough texture
long dry time
• Lint fi lter is not clean.
• Restriction in exhaust.
• Outside exhaust hood damper door stuck closed.
• Exhaust too long, too many elbows, fl ex ductwork installed.
• Poor intake air available for the dryer.
• Incorrect tumbler speed. Tumbler belt slipping.
• Blower impeller bound; check for foreign material in blower area.
• Customer overloading dryer.
• Check clothing labels for fabric content and cycle selected.
• Clothes too wet due to insuffi cient spin out by washer.
12 Noisy and/Or Vibration
• Thumping Check for loose tumbler baffl e, rear tumbler roller(s) worn or
misaligned, out-of-round tumbler or high weld seam on tumbler.
• Ticking Check for loose wire harness or object caught in blower wheel area.
• Scraping Check for front or rear bulkhead felt seal out of position or worn
tumbler front bearings.
• Roaring Check for blower wheel rubbing on blower housing or bad motor
bearings.
• Popping or squealing sound. Check for a sticky or frayed belt.
6-3
9051#SUREOHP#FKHFNLQJ#DQG#PHWKRG#RI#SFE
-If you plug in the power cord and turn Power S/W on, memorized data is displayed.
If any data is not displayed, check the followings.
90504#Wkh#Sduw#Ri#Srzhu#Vrxufh#
The Voltage Of
Betweenⓐand ⓑIs
As Big As 12V?
Yes
No
The Voltage Of
Betweenⓒand ⓓ Is
As Big As 12V?
Yes
No
The Voltage Of
Betweenⓔand ⓓ Is
As Big As 5V?
Check The Trans
Check The Diode
(D11,D12,D16,D17,D18)
And Condenser(CE3)
Exchange IC3(7805) And Check
The Condenser(CE5)
No Power ON
Yes
No
6-4
905051#Uhvhw#Sduw
Check The Curve
Output Of ⓐ ?
Yes
Check The Micom
Number 67 ?
Check D11,12,16,17,18
Check TR2,R35
Check The Part Of
Oscillator
Yes
The Value Of Measurement
Result Of Between Micom 25
And Gnd Is 5V?
No Check The Power Source
Check IC4
Yes
25
7533
IC4
R40 100
CE7 1UF
905061#Lqwhuuxsw#Sduw
6-5
905071#Fkhfnlqj#Wkh#Sduw#Ri#Dq#Rvfloodwru
The Value Of Measurement
Result Of Between Micom 25
And Gnd Is 5V?
No Check The Power Source
Check IC4
Yes
905081#Fkhfn#Wkh#Sduw#Ri#Ex}}hu
ⓐ Part Confirm DC12V ?
No Check The Part Of Power Source
Exchange BUZZER1,
Check R5,R46
Yes
6-6
Memo
8-1
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
8. ELECTRICAL PARTS LIST
-You can search for updated part codes through ITSELF web site.
URL : http://itself.sec.samsung.co.kr/
H0001 DC96-00791A ASSY-MOTOR DUCT;MDE7800AYW,240V/60HZ 1 SNA
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 2 SA
U0095 6602-001314 BELT-TIMING GEAR;0724,RUBBER(GOODYEAR),T 1 SA
H0032 DC96-01112A ASSY-MOTOR;MDE9700AYW,DRYER/MOTOR 1 SA
H0002 DC31-00055A MOTOR-DRYER;-,WINGS-PJT,-,120V 60Hz,-,-, 1 SA
DC96-00790B ASSY-BRACKET MOTOR;MDE9700AYW,DRYER/MOTO 1 SA
H0004 DC61-01213A BRACKET-MOTOR;WINGS-DRYER,HGI,T2.0,-,-,- 1 SA
H0073 DC61-01215A SPRING-TENSION;WINGS-DRYER,HSWR,-,-,-,-, 2 SA
C0103 3405-001077 SWITCH-MICRO;125V,15A,180gf,2 1 SA
Z0051 6002-000488 SCREW-TAPPING;PH,+,-,2S,M3,L16,ZPC(YEL), 1 SA
Z0033 6009-001342 SCREW-SPECIAL;TH,+,-,M5,L11,ZPC(YEL),SWR 1 SA
DC61-01449A HOLDER-BRACKET;MDE9700AYW,HSWR,T2.5,W30, 1 SNA
H0082 DC96-00882B ASSY-BRACKET IDLER;MDE9800AYW,DRYER/IDLE 1 SA
R0165 DC61-01228A HOLDER-SHAFT;WINGS-DRYER,NYLON#6,-,-,-,N 1 SA
H0008 DC61-01230A BRACKET-IDLER;WINGS-DRYER,SECC(EGI),T2.0 1 SNA
H0083 DC66-00401A SHAFT-IDLER;WINGS-DRYER,STS-410,-,-,-,-, 1 SNA
H0081 DC97-07509B ASSY-ROLLER;MDE9700AYW,DRYER/MOTOR/IDLER 1 SA
H0084 DC66-00402A ROLLER-IDLER;WINGS-DRYER,POM,-,-,-,-,MOT 1 SA
6601-001291 BEARING-OILLESS;-,ID13,OD21.8,L22,FE+OIL 1 SNA
DC97-07508A ASSY-COVER DUCT;MDE7800AYW,DRYER 1 SNA
W0035 DC32-00007A THERMISTOR;N3S1-K41-S1,10K,10KOHM 25,-40 1 SA
F0005 DC47-00016A THERMOSTAT;B-2,-,250V,25A,-20~150,-40~15 1 SA
W0013 DC61-01240A BRACKET-THERMISTOR;WINGS-DRYER,TB-54,-,- 1 SA
U0371 DC61-01241A GUIDE-DUCT FAN;WINGS-DRYER,TB-54,-,-,-,W 1 SA
H0013 DC63-00536A COVER-DUCT FAN;WINGS-DRYER,TB-54,-,-,-,- 1 SA
Z0039 6002-000470 SCREW-TAPPING;TH,+,-,1,M4,L10,ZPC(YEL),S 5 SC
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 3 SA
Z0053 6021-001201 NUT-INCH;LEFT TURN,3/8”-24,ZPC(YEL),MSW 1 SA
H0080 DC61-01214A SPRING-PLATE;WINGS-DRYER,SK-5,-,-,-,-,-, 2 SA
H0048 DC67-00180A FAN;WINGS-DRYER,FRPP(15%),-,-,-,MO 1 SA
DC66-00440A BLADE-BLOWER;WINGS-DRYER,FRPP(15%),-,-,- 1 SNA
H0040 DC61-01205A BUSH-FAN;WINGS-DRYER,STS430,-,-,-,-,FAN 1 SNA
Z0006 6002-000213 SCREW-TAPPING;TH,+,-,1,M4,L12,ZPC(YEL),S 2 SNA
R0001 DC97-10356A ASSY-DRUM;DV736E4/XAA,FRONTIER 1 SNA
Z0006 6002-000213 SCREW-TAPPING;TH,+,-,1,M4,L12,ZPC(YEL),S 3 SNA
Z0020 6006-001174 SCREW-TAPPING;WE,TH,+,M4,L12,ZPC(YEL) 11 SA
I0064 DC61-01521A CASE-FILTER;DV736E4/XAA(FRONTIER),FRPP(G 1 SA
M0066 DC61-01522A DIE-RACK DRY;WINGS-DRYER,TB-54,-,-,NTR,P 1 SA
N0006 DC61-40081A HOLDER-WIRE;DAWH-2NC,NYLON66,-,-,-,-,NTR 1 SA
U0372 DC97-07526A ASSY-DUCT OUTLET;MDE7800AYW,SRYER/ELECTR 1 SA
SNA
D0111 DC63-10001K SPONGE-EPDM;SWF-P12,EPDM,-,T3,W15,L530,B 1 SNA
DC67-00127A DUCT-OUTLET(F);WINGS-DRYER,AL-COAT,T0.6, 1 SNA
DC67-00128A DUCT-OUTLET(B);WINGS-DRYER,AL-COAT,T0.6, 1 SNA
D0111 DC72-00032A SPONGE-EPDM;MDE7800AYW,EPDM,-,T5,W20,L40 1 SNA
D0111 DC72-00032C SPONGE-EPDM;MDE7800AYW,EPDM,-,T5,W20,L38 1 SNA
R0015 DC97-08300A ASSY-DRUM BACK;MDG7800AWW,GAS/PREMIUM/ST 1 SNA
8-2
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
Z0007 6002-000239 SCREW-TAPPING;TH,+,-,2S,M4,L8,ZPC(YEL),S 9 SC
Z0004 DC60-50145A NUT-HEX;-,MSWR10,-,-,-,-,-,-,M10 2 SA
H0074 DC60-60060A WASHER;-,T2,-,ID12,OD24,-,YEL,- 4 SA
R0170 DC61-01237A BRACKET-DRUM BACK;WINGS-DRYER,SECC(EGI), 1 SA
R0170 DC61-01238A BRACKET-DRUM BACK;WINGS-DRYER,SECC(EGI), 2 SA
H0081 DC97-07523A ASSY-ROLLER;MDE7800AYW,DRYER/EPDM 2 SA
6601-001291 BEARING-OILLESS;-,ID13,OD21.8,L22,FE+OIL 1 SNA
R0164 DC61-01227A GUIDE-ROLLER;WINGS-DRYER,PP,-,-,-,BLU,- 1 SNA
R0165 DC61-01228A HOLDER-SHAFT;WINGS-DRYER,NYLON#6,-,-,-,N 2 SA
R0168 DC66-00394A ROLLER;WINGS-PROJECT,EPDM,-,-,BLK,-,I 1 SNA
DC66-00400A SHAFT-ROLLER;WINGS-DRYER,STS-410,L56,OD1 1 SNA
R0005 DC66-00398B DRUM-BACK;WINGS-DRYER,STS430M,-,-,-,HAIR 1 SA
U0374 DC97-07521B ASSY-DUCT AIR;MDG4800AWW,GAS DRYER/WING 1 SA
DC67-00134B DUCT-AIR(F);WINGS-DRYER,AL-COAT,T0.6,-,- 1 SNA
DC67-00135B DUCT-AIR(B);WINGS-DRYER,AL-COAT,T0.6,-,- 1 SNA
R0016 DC97-10354A ASSY-DRUM FRONT;DV736E4/XAA,FRONTIER-DRY 1 SNA
R0163 4713-001199 LAMP-INCANDESCENT;120V,83mA,10W,NTR,-,-, 1 SA
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 1 SA
Z0028 6002-000445 SCREW-TAPPING;TH,+,-,2S,M4,L18,PASS,STS4 3 SA
Z0052 6002-001320 SCREW-TAPPING;TH,+,2S,M4,L8,PASS,STS304, 3 SA
A0125 6046-000310 STAND OFF;ID11.5,L2,NTR,NYLON66,DAWH-3NA 3 SA
F0118 DC47-00021A SOCKET-LAMP;-,MDE7800,E12,125V,0.6A,-,12 1 SA
Z0004 DC60-50145A NUT-HEX;-,MSWR10,-,-,-,-,-,-,M10 2 SA
H0074 DC60-60060A WASHER;-,T2,-,ID12,OD24,-,YEL,- 4 SA
F0227 DC61-01220A GUIDE-LAMP;WINGS-DRYER,TB-54,-,-,-,BLK,I 1 SA
F0041 DC63-00531A COVER-LAMP;WINGS-DRYER,PC(LEXAN#141R),-, 1 SA
I0056 DC63-00538A COVER-FILTER(F);WINGS-DRYER,TI-42,-,-,-, 1 SA
I0057 DC63-00675A COVER-FILTER(B);DV736E4/XAA,TI-42,-,-,-, 1 SA
H0081 DC97-07523A ASSY-ROLLER;MDE7800AYW,DRYER/EPDM 2 SA
6601-001291 BEARING-OILLESS;-,ID13,OD21.8,L22,FE+OIL 1 SNA
R0164 DC61-01227A GUIDE-ROLLER;WINGS-DRYER,PP,-,-,-,BLU,- 1 SNA
R0165 DC61-01228A HOLDER-SHAFT;WINGS-DRYER,NYLON#6,-,-,-,N 2 SA
R0168 DC66-00394A ROLLER;WINGS-PROJECT,EPDM,-,-,BLK,-,I 1 SNA
DC66-00400A SHAFT-ROLLER;WINGS-DRYER,STS-410,L56,OD1 1 SNA
SNA
Q0001 DC97-08894A ASSY-GUIDE SENSOR(M);MDE9700AYW,TOUCH SE 1 SNA
W0001 DC96-00766A ASSY-WIRE HARNESS;GR-PJT,SUB/TOUCH SENSO 1 SA
Q0002 DC97-08889A ASSY-GUIDE SENSOR;MDE9700AYW,YOUCH SENSO 1 SA
Q0003 DC61-01231A PLATE-SENSOR;WINGS-DRYER,STS-430,T0.8,-, 2 SA
Q0004 DC61-01235A GUIDE-SENSOR;WINGS-DRYER,TI-42,-,-,-,GRY 1 SA
A0371 DC97-10362A ASSY-S.DRUM FRONT;DV736E4/XAA,FRONTIER-D 1 SA
F0117 6041-001035 RIVET-RH;K1661-0512,AL(A5052),OD3.9,L11 4 SNA
DC61-01236A BRACKET-DRUM FRONT;WINGS-DRYER,SECC(EGI) 4 SNA
R0002 DC66-00435A DRUM-FRONT;DV736E4/XAA,SECC(EGI),T1.0,-, 1 SNA
R0172 DC97-10355A ASSY-DRUM WRAPPER;DV736E4/XAA,FRONTIER(G 1 SA
Z0041 6002-001204 SCREW-TAPPING;TH,+,-,1,M4,L16,PASS,STS43 12 SA
8-3
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
DC02-00014A CHEMICALS-BOND;MDE7800AYW,-,-,-,ASSY-FEL 25 SNA
A0356 DC63-00597C SHEET-DAMPING;MDE9700AYW,BUTYL,T1.5,W100 6 SNA
R0003 DC66-00397A DRUM-WRAPPER;WINGS-DRYER,STS-304,T0.6,-, 1 SNA
R0006 DC66-00436A DRUM-LIFTER;DV736E4/XAA,TI-42,-,-,-,GRY, 3 SA
F0024 DC97-07618A ASSY-GASKET PAD;MDE7800AYW,DRYER/DRUM-WR 2 SNA
A0001 DC97-10370A ASSY-CASE;DV736E4/XAA,FRONTIER-DRYER 1 SNA
0203-001508 TAPE-OPP;W50,,YEL 1 SNA
V0007 6801-001310 CARD-REGISTRATION;USA,XAA,ENGLISH,MOJOJI 1 SNA
6902-000340 BAG PE;HDPE,T0.015,W230,L360,TRP,8,2- 1 SNA
DC65-60115A BAND-PP;-,PP,T0.8,W17.5,-,WHT,- 15.2 SNA
DC68-02173A LABEL-PACKING;W/M,-,ART,-,W90,L175,-,WHT 1 SNA
V0004 DC68-02219A LABEL-WARNING;MAYTAG,-,ART+LAMI,-,W170,L 1 SNA
A0244 DC68-02235A LABEL-CAUTION;MAYTAG,-,ART+LAMI,-,W95,L4 1 SNA
A0244 DC68-02236A LABEL-CAUTION;MAYTAG,-,YUPO,-,W90,L37.0, 1 SNA
V0002 DC68-02238A LABEL RATING;MAYTAG,-,YUPOJI,-,W136,L37, 1 SNA
DC68-02298A LABEL-POWER CORD;WF326,SEA,ART+LAMI,-,W1 1 SNA
V0002 DC68-02309B LABEL RATING;DV316,SEC,YUPOJI,-,W106,L25 1 SNA
A0243 DC68-02312A MANUAL-BOOK;DV316,SEA,ENGLISH,U.S,100MOJ 1 SNA
DC68-02313A LABEL-CLEARANCE;DV316,-,ART+LAMI,-,W140, 1 SNA
DC68-02319A LABEL-DIAGRAM SCHEMATIC;DV316,-,YUPO,-,- 1 SNA
V0004 DC68-02320A LABEL-WARNING;DV316,SEA,ART+LAMI,-,-,-,- 1 SNA
V0004 DC68-02321A LABEL-WARNING;DV316,SEA,ART+LAMI,-,-,-,- 1 SNA
A0244 DC68-02322A LABEL-CAUTION;DV316,SEA,ART+LAMI,-,-,-,- 1 SNA
V0004 DC68-02324A LABEL-WARNING;DV316,SEA,ART+LAMI,-,-,-,- 1 SNA
DC68-20091B LABEL-BAR CODE;MOJO,W32,L125.5,-,- 1 SNA
DC69-00367A SHEET-PE;GW10-PJT,PE-FOAM,T0.5,L1050,W9 1 SNA
D0053 DC69-00923A CUSHION-DOOR;MDE9700AYW,PS-FOAM,T8,W40,L 1 SNA
A0015 DC69-00935B PACKING CASE-DESIGN;DV316LGW,SW3,-,-,W74 1 SNA
X0007 DC69-00965A CUSHION-BOTTOM;DV736E4/XAA,PS-FOAM,-,-,- 1 SNA
A0197 DC69-00967A CUSHION-TOP;WF326LAW,PS-FOAM,-,-,-,-,-,N 1 SNA
DC69-90009A TAPE-SCOTCH PAR;FILAMENT-TAPE,-,W50,-,- 1.4 SNA
W0002 DC96-00038G ASSY POWER CORD;DV4006,EP3(16A)DRYER 1 SA
C0027 DC97-10371A ASSY-CONTROL;DV736E4/XAA,FRONTIER-DRYER 1 SNA
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 7 SA
Z0020 6006-001174 SCREW-TAPPING;WE,TH,+,M4,L12,ZPC(YEL) 5 SA
Z0048 6009-001476 SCREW-HEX;HEX,+,-,M5,L10,ZPC3(BLK),SWRCH 2 SA
F0125 DC61-01525A FRAME-PLATE(U);DV736E4/XAA,SECC(EGI),-,- 1 SNA
N0006 DC61-40081A HOLDER-WIRE;DAWH-2NC,NYLON66,-,-,-,-,NTR 1 SA
A0364 DC61-60074A CLAMPER-WIRE SADDLE;-,NYLON#66(DAWS-6NB) 1 SA
W0037 DC96-00763A ASSY-FLAT WIRE HARNESS;GR-PJT,FLAT WIRE 1 SA
W0004 DC96-00765A ASSY-M.WIRE HARNESS;GR-PJT,GAS USA 1 SA
P0001 DC97-08634A ASSY-COVER TOP;GW-PJT,- 1 SA
P0053 DC63-00523A COVER-TOP;GW-PJT,SECC(EGI),T1.0,W684,L56 1 SNA
W0059 DC63-10002Q SPONGE-HARNESS;KS-PJT,PU-FOAM,-,T3,W100, 1 SNA
F0037 DC97-10357A ASSY-FRONT;DV736E4/XAA,FRONTIER-DRYER 1 SNA
Z0027 6001-001773 SCREW-MACHINE;TH,+,-,M5,L12,PASS,STS430, 2 SA
8-4
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
Z0008 6002-000444 SCREW-TAPPING;TH,+,-,2S,M4,L14,PASS,STS4 2 SA
Z0020 6006-001174 SCREW-TAPPING;WE,TH,+,M4,L12,ZPC(YEL) 3 SA
F0064 DC97-10353A ASSY-FRAME FRONT;DV736E4/XAA,FRONTIER-DR 1 SNA
Z0027 6001-001773 SCREW-MACHINE;TH,+,-,M5,L12,PASS,STS430, 2 SA
Z0008 6002-000444 SCREW-TAPPING;TH,+,-,2S,M4,L14,PASS,STS4 2 SA
D0048 DC61-01222A BRACKET-HINGE;WINGS-DRYER,SECC(EGI),T1.6 2 SA
F0103 DC61-01524A FRAME-FRONT;DV736E4/XAA,SECC(EGI),-,-,WH 1 SNA
F0042 DC64-00828A DOOR-S/W;GD-PJT,PA,T13.6,H38.5,W44.3,-, 1 SA
SNA
D0111 DC72-00032B SPONGE-EPDM;MDE7800AYW,EPDM,-,T3,W15,L34 4 SA
D0113 DC97-07510A ASSY-HOLDER LEVER;MDE7800AYW,DRYER/DOOR 1 SA
DC61-01239A HOLDER-LEVER;WINGS-DRYER,POM,-,-,-,GRY,- 1 SNA
H0073 DC61-01295A SPRING-TENSION;WINGS-DRYER,HSWR,CD1.2,ID 2 SNA
D0109 DC61-01296A GUIDE-LEVER;WINGS-DRYER(ENTRY),POM,-,-,- 2 SNA
DC63-00556A COVER-HOLDER;WINGS-DRYER,POM,-,-,-,-,-,G 1 SNA
D0001 DC97-10867A ASSY-DOOR;DV316LGW,FRONTIER(DRYER) 1 SNA
Z0006 6002-000213 SCREW-TAPPING;TH,+,-,1,M4,L12,ZPC(YEL),S 8 SNA
Z0008 6002-000444 SCREW-TAPPING;TH,+,-,2S,M4,L14,PASS,STS4 15 SA
D0072 DC61-00891A GUIDE-HINGE;HAUZEN(DOM),POM,-,-,-,WHT,HI 4 SA
D0081 DC61-01523A HOLDER-GLASS;DV736E4/XAA,TB-53,-,-,-,GRY 1 SA
D0108 DC61-01532A HINGE-DOOR;WF326LAW,ZNDC,T3.8,-,-,-,-,FR 1 SA
D0105 DC61-01576A SUPPORT-HINGE;FRONTIER-PJT,STS430,T1.2,- 1 SNA
D0094 DC62-00198B SEAL-DOOR;WINGS-DRYER,SILICON,GRY,-,-,-, 1 SA
D0061 DC64-00993A DOOR-GLASS;WINGS-DRYER,GLASS,T5,-,-,-,TR 1 SA
D0107 DC66-00395A LEVER-DOOR;WINGS-DRYER,POM,-,-,-,-,NTR,- 1 SA
D0010 DC97-10338A ASSY-COVER DOOR;WF326LAW,FRONTIER 1 SA
D0106 DC63-00673A COVER-DOOR;WF316LAW,ABS,T2.8,-,-,-,-,CR- 1 SNA
D0066 DC64-01120A DOOR-SAFETY;WF326LAW,PET,T2.8,-,-,-,NTR, 1 SA
DC64-01121A DECORATION-DOOR;WF326LAW,STS430,T0.6,-,- 1 SNA
0203-001838 TAPE-DOUBLE FACE;4930,EPDM,T0.6,W41,R213 10 SNA
C0002 DC97-10358A ASSY-PANEL CONTROL;DV736E4/XAA,GOOD MODE 1 SNA
Z0006 6002-000213 SCREW-TAPPING;TH,+,-,1,M4,L12,ZPC(YEL),S 5 SNA
C0105 DC64-01108A BUTTON-ENCODER;WF326LAW,ABS,-,-,WHT,FRON 1 SA
C0029 DC97-10511A ASSY-KNOB ENCODER;FRONTIER,LOWES 1 SA
C0075 DC64-01084A KNOB-ENCODER(I);K4-PJT,ABS,-,-,-,-,WHT,- 1 SNA
C0104 DC64-01106A KNOB-ENCODER;WF326LAW,ABS,-,-,-,-,WHT,-, 1 SNA
DC97-10866A ASSY-S.PANEL CONTROL;FRONTIER(DRYER),DV3 1 SA
DC61-01546A GUIDE-ENCODER;DV326LGS,ABS,-,-,-,NTR,FRO 1 SNA
C0044 DC64-01105A BUTTON-PUSH(P);WF326LAW,ABS,-,-,WHT,FRON 1 SA
C0043 DC64-01110A BUTTON-PUSH(F);WF326LAW,ABS,-,-,WHT,FRON 1 SNA
C0008 DC64-01112A WINDOW-ENCODER;WF326LAW,SAN,-,-,-,-,TRAN 1 SNA
DC64-01118A BUTTON-PUSH(AG);WF326AW,ABS,-,-,TRANSPAR 1 SNA
C0082 DC64-01122A PANEL-CONTROL;DV736E4/XAA,ABS,-,-,-,-,WH 1 SNA
A0242 DC64-01126A INLAY-PANEL;WF316LAW,PET,T0.188,-,-,WHT, 1 SNA
DC64-01139A BUTTON-PUSH(C);WF326LAW,ABS,-,-,TRANS,FR 1 SNA
8-5
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
C0106 DC64-01158A MASCOT;WF326LAW,NICKEL,T0.5,W10.5,L65 1 SNA
C0108 DC66-00413A LEVER-POWER;GW-PJT,POM,-,-,-,-,NTR,ENTRY 1 SA
Y0162 MFS-F12DL-S0 ASSY PCB PARTS(S);MFS-F12DL-S0 FRONTIER 1 SA
0401-000005 DIODE-SWITCHING;1N4148,75V,150mA,DO-35,T 8 SNA
Y0063 0601-001028 LED;ROUND,Y-GRN,3mm,569nm 30 SNA
Y0063 0601-001751 LED;ROUND,RED,3MM,630NM,- 1 SNA
Y0051 1003-000337 IC-DARLINGTON DRIVER;KID65783AP,DIP,18P, 1 SNA
2003-000642 R-METAL OXIDE(S);300ohm,5%,1W,AA,TP,3.3x 11 SNA
2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V 1 SNA
Y0087 3404-001022 SWITCH-TACT;15V,20mA,130±40gf,6x6x5mm,S 11 SNA
3711-000651 HEADER-BOARD TO CABLE;BOX,12P,1R,2.5mm,S 1 SNA
3711-003133 HEADER-BOARD TO CABLE;BOX,13P,1R,2.5mm,S 1 SNA
C0011 DC07-00038A LED DISPLAY;CSV-KSW07EG,FRONTIER-PJT,-,7 1 SNA
DC34-00003A SWITCH PRESSURE;V7_PJT,DC28V,10mA,24,-,J 1 SNA
DC41-00045A PCB-SUB;FRONTIER,FR-1,NL 1,-,T1.6,197x 1 SA
DC61-01207A GUIDE-PCB(S);WINGS-DRYER,HIPS,-,-,-,NTR, 1 SNA
DC61-01514A GUIDE-LED(B);WF-G106AW,HIPS,-,-,-,NTR,FR 1 SNA
DC61-01516A GUIDE-LED(C);WF-G106AW,HIPS,-,-,-,NTR,FR 1 SNA
DE02-00036A CHEMICALS-FLUX SOLDER;KS-77S,-,-,-,-,KOK 2 SNA
DE02-00060A CHEMICALS-ALCOHOL;ALL,MODEL,-,-,-,-,-,- 1 SNA
DE02-00083A SOLDER-WIRE;S63S,D3.0,-,-,-,-,-,-,- 10 SNA
DE02-00086A SOLDER-WIRE FLUX;RS60S,-,D1.2,60SN/40PB, 1 SNA
Y0052 DE13-20017A IC-DRIVE;KID65003AP,DIP,16P,STICK,TR-AR 2 SNA
DE39-60001A WIRE-SO COPPER;,PI0.6,SN,T,52MM TAPING_W 53 SNA
DC97-10875A ASSY-HOLDER PCB;DV316LGW/XAA,FRONTIER/PC 1 SNA
A0367 DC61-01229A HOLDER-PCB;WINGS-DRYER,SECC(EGI),T0.8,-, 1 SA
Y0161 MFS-FTDT-00 ASSY PCB PARTS(M);MFS-FTDT-00 1 SA
0103-002581 RESIN-PUR;CPU-55B/UEP 700FB,-,-,94V0 94.7 SNA
0103-002582 RESIN-PUR;UEP 700FA/CPU-55A,-,-,94V0 47.3 SNA
0401-000005 DIODE-SWITCHING;1N4148,75V,150mA,DO-35,T 4 SNA
0402-000137 DIODE-RECTIFIER;1N4007,1KV,1A,DO-41,TP 5 SNA
0501-000316 TR-SMALL SIGNAL;KSA928A-Y,PNP,1000mW,TO- 2 SNA
E0002 0504-001014 TR-DIGITAL;KSR1005,NPN,300MW,4.7K/10K,TO 1 SNA
0604-000118 PHOTO-COUPLER;TR,20-300%,200mW,DIP-4,ST 2 SNA
Y0053 1103-001203 IC-EEPROM;524C20D21,256x8,DIP,8P,9.6x6.4 1 SNA
1202-000001 IC-VOLTAGE COMP.;7533,TO-92,3P,-,SINGLE, 1 SNA
1405-001129 VARISTOR;460VDC,7500A,22.5X10.1MM,BK 1 SNA
2001-000034 R-CARBON;220OHM,5%,1/4W,AA,TP,2.4X6.4MM 1 SNA
2001-000042 R-CARBON;1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 1 SNA
2001-000047 R-CARBON;2.2KOHM,5%,1/4W,AA,TP,2.4X6.4M 1 SNA
2001-000052 R-CARBON(S);3.3KOHM,5%,1/2W,AA,TP,2.4X6. 1 SNA
2001-000073 R-CARBON;33Kohm,5%,1/4W,AA,TP,2.4x6.4mm 1 SNA
2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM 3 SNA
2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15 SNA
2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 23 SNA
2001-000432 R-CARBON;1MOHM,5%,1/4W,AA,TP,2.4X6.4MM 2 SNA
8-6
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1 SNA
2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M 6 SNA
2001-001113 R-CARBON(S);270KOHM,5%,1/2W,AA,TP,2.4X6. 1 SNA
2001-001140 R-CARBON(S);39OHM,5%,1/2W,AA,TP,2.4X6.4M 1 SNA
2001-001153 R-CARBON(S);47ohm,5%,1/2W,AA,TP,2.4x6.4m 1 SNA
2003-002036 R-METAL OXIDE(S);51Kohm,5%,2W,AA,TP,4x12 4 SNA
2004-000464 R-METAL;2.2Mohm,5%,1/4W,AA,TP,2.4x6.4m 2 SNA
2201-000153 C-CERAMIC,DISC;10nF,+80-20%,250V,Y5V,-,1 1 SNA
2202-000127 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V 12 SNA
2202-000252 C-CERAMIC,MLC-AXIAL;4.7nF,10%,50V,X7R,TP 2 SNA
2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V 10 SNA
2301-001285 C-FILM,LEAD-PPF;680NF,10%,275V,BK,31X11X 1 SNA
2401-000455 C-AL;10uF,20%,35V,GP,TP,4x7mm,5 1 SNA
SNA
2401-000598 C-AL;1uF,20%,50V,GP,TP,4x7,5 1 SNA
2401-000711 C-AL;2200uF,20%,25V,GP,TP,16x25,7.5 1 SNA
2401-001573 C-AL;47uF,20%,50V,GP,TP,6.3x11,2.5 1 SNA
2401-001778 C-AL;470uF,20%,25V,GP,TP,10x16,5 1 SNA
Y0115 2802-000188 RESONATOR-CERAMIC;8MHz,0.5%,TP,10.0x5.0x 1 SNA
Y0116 3501-001207 RELAY-POWER;12V DC,0.8W,30000MA,1FORMA,1 1 SNA
Y0116 3501-001269 RELAY-POWER;12VDC,-,25000MA,1FORMA,20MS, 1 SNA
3711-000744 HEADER-BOARD TO CABLE;BOX,1P,1R,8MM,STRA 1 SNA
3711-000833 HEADER-BOARD TO CABLE;BOX,2P,1R,8MM,STRA 1 SNA
3711-005688 HEADER-BOARD TO CABLE;BOX,13P,1R,2.5mm,S 1 SNA
3711-005693 HEADER-BOARD TO CABLE;BOX,12P,1R,2.5mm,S 1 SNA
3711-005703 HEADER-BOARD TO CABLE;BOX,6P,1R,2.5mm,ST 1 SNA
C0010 DC13-00148A PLD-MICOM;TMP87PM41N/OTP,DIP,64 PIN 1 SNA
DC26-00005C TRANS-POWER;-,MAH2400AW,9PIN,-,230VAC,23 1 SNA
DC41-00027A PCB-MAIN;MFS-MDE27-00,FR-4,2,-,T1.6,195 1 SNA
Y0003 DC61-01208A GUIDE-PCB(M);WINGS-DRYER,HIPS,-,-,-,NTR, 1 SNA
DE02-00036A CHEMICALS-FLUX SOLDER;KS-77S,-,-,-,-,KOK 2 SNA
DE02-00060A CHEMICALS-ALCOHOL;ALL,MODEL,-,-,-,-,-,- 2 SNA
DE02-00083A SOLDER-WIRE;S63S,D3.0,-,-,-,-,-,-,- 20 SNA
DE02-00086A SOLDER-WIRE FLUX;RS60S,-,D1.2,60SN/40PB, 1 SNA
DE13-20007A IC-OP AMP;KA2904,DIP,-,-,-,-,- 1 SNA
Y0057 DE13-20016A IC-VOLT REGU;KA7805A,TO-220AB,1A,0/125C, 1 SNA
Y0052 DE13-20017A IC-DRIVE;KID65003AP,DIP,16P,STICK,TR-AR 1 SNA
Y0040 DE29-90002A FILTER-EMI BEAD;S,80/100MHZ-MIN65,T,BFS3 1 SNA
Y0010 DE30-20016A BUZZER;CBE2220BA,STICK,-,-,-,-,-,-,- 1 SNA
Z0007 6002-000239 SCREW-TAPPING;TH,+,-,2S,M4,L8,ZPC(YEL),S 1 SC
U0363 6502-000127 CABLE CLAMP;DAWH-18NB,ID15,-,NYLON66,NTR 1 SA
A0364 DC61-60074A CLAMPER-WIRE SADDLE;-,NYLON#66(DAWS-6NB) 1 SA
F0001 DC97-10871A ASSY-FRAME CASE;DV316LGW/XAA,FRONTIER-DR 1 SNA
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 6 SA
Z0007 6002-000239 SCREW-TAPPING;TH,+,-,2S,M4,L8,ZPC(YEL),S 10 SC
Z0062 6002-001384 SCREW-TAPPING;TH,+,WT,C-TITE,M4,L10,ZPC( 1 SNA
Z0019 6006-001170 SCREW-TAPPING;TH,+,WT,TC,M4,L10,ZPC(YEL) 1 SA
8-7
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
Z0020 6006-001174 SCREW-TAPPING;WE,TH,+,M4,L12,ZPC(YEL) 2 SA
6009-001317 SCREW-SPECIAL;CH,+,-,M4,L10,ZPC(YEL),SWR 2 SNA
Z0021 6009-001343 SCREW-SPECIAL;PH,TORX,-,M4,L10,PASS,STS, 1 SA
P0077 DC61-00882A HOLDER-D.WIRE;-,NYLON66,-,-,-,NTR,TT-PJT 1 SNA
F0228 DC61-01224A DIE-HEATER;WINGS-DRYER,SECC(EGI),-,-,NTR 1 SA
F0229 DC61-01233A GUIDE-EXHAUST;WINGS-DRYER,SECC(EGI),T0.8 1 SA
N0006 DC61-40081A HOLDER-WIRE;DAWH-2NC,NYLON66,-,-,-,-,NTR 11 SA
A0364 DC61-60074A CLAMPER-WIRE SADDLE;-,NYLON#66(DAWS-6NB) 1 SA
A0282 DC63-00534A COVER-BACK;WINGS-DRYER,SECC(EGI),T0.8,-, 1 SA
D0111 DC63-10001J SPONGE-EPDM;EPDM,BLK,SDW-801SW,T3XW15XL1 2 SNA
DC67-00202A CAP-PLATE BOTTOM;MDE9700AYW,ABS,T2.0,W54 3 SNA
U0382 DC96-00806A ASSY-BRACKET BURNER;MDE9700AYW,DRYER/GAS 1 SNA
W0061 DC47-00022A HEATER-IGNITER;101D,MDG7800AW,CERAMIC,12 1 SA
U0381 DC61-01232A BRACKET-BURNER;WINGS-DRYER,SECC(EGI),T1. 1 SA
U0387 DC62-00200A TUBE-BURNER;WINGS-DRYER,PRESS(GAS UNIT), 1 SA
U0386 DC62-00201A VALVE-GAS;GD-PJT,-,3WAY,MAX 10BAR,NTR,12 1 SA
U0388 DC63-00623A ABSORBER-IGNITOR;MDE9700AYW,FELT,T2,W10, 1 SA
I0070 DC99-00507A ASSY-PIPE;MDG4800AWW,GAS DRYER/ELBOW ASS 1 SA
DC60-00040A ELBOW;WINGS-DRYER,C3771BE,-,-,-,-,-, 1 SNA
DC61-01223A BRACKET-PIPE;WINGS-DRYER,SECC(EGI),T2.0, 1 SNA
DC62-00234A TUBE-PIPE;WINGS-DRYER,PRESS(GAS UNIT),-, 1 SNA
Z0048 6009-001476 SCREW-HEX;HEX,+,-,M5,L10,ZPC3(BLK),SWRCH 1 SA
DC97-09193A ASSY-SCREW;MDG9700AWW,NUT-CIRCULAR+SCREW 1 SNA
Z0062 6002-000524 SCREW-TAPPING;TH,+,2,M4,L20,ZPC(YEL),SWR 1 SA
Z0063 6021-001130 NUT-CIRCULAR;SPN-4,ID3.8,OD12,BLK,SK-5,H 1 SA
Z0020 6006-001174 SCREW-TAPPING;WE,TH,+,M4,L12,ZPC(YEL) 3 SA
B0070 DC97-07514A ASSY-LEG;MDE9700AYW,DRYER/MAYTAG 4 SA
B0074 DC61-01212A LEG;WINGS-PROJECT,FRPP,-,-,-,- 1 SA
B0075 DC61-01226A BRACKET-LEG;WINGS-DRYER,SECC(EGI),T1.6,- 1 SA
F0028 DC97-07516B ASSY-FRAME;MDG9700AWW,MAYTAG/PREMIUM/GAS 1 SA
F0094 DC61-01199B FRAME;WINGS-PROJECT,PCM,-,-,WHT,T0.8 1 SNA
Y0159 DC61-01314A PLATE-STEEL;MDE7800AYW,PCM(GI),T0.8,W961 1 SNA
X0014 DC61-01225A PLATE-BOTTOM;WINGS-DRYER,SECC(EGI),T1.0, 1 SNA
A0113 DC63-00621A SHEET-INSULATION;MDE9700AYW,FELT,T5,W200 1 SNA
F0117 6041-001035 RIVET-RH;K1661-0512,AL(A5052),OD3.9,L11 4 SNA
A0370 DC97-07519A ASSY-DUCT EXHAUST;MDE7800AYW,DRYER 1 SA
DC61-01234A BRACKET-EXHAUST;WINGS-DRYER,AL-COAT,T0.8 2 SNA
DC67-00131A DUCT-EXHAUST;WINGS-DRYER,SGCC(GI),T0.4,- 1 SNA
D0111 DC72-00032D SPONGE-EPDM;MDE7800AYW,EPDM,-,T3,W15,L32 1 SNA
F0117 6041-001030 RIVET-RH;K1661-00410,AL(A5052),D3.2,L10 2 SNA
P0170 DC97-08855A ASSY-COVER POWER;MDE9700AYW,- 1 SA
F0089 DC63-00540A COVER-POWER;WINGS-DRYER,SGCC(GI),T0.8,-, 1 SA
A0356 DC66-60133C SHEET-DAMPING;SEW-HR125,ASPHALT,T1.8,W50 1 SNA
DC97-10720A ASSY-DUCT;MDG9700AWW,GAS 1 SA
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 3 SA
Q0007 DC32-00008A SENSOR-RADIANT;10RS,GD-PJT,0~150,120,4.5 1 SA
8-8
Loc. No. Code No. Description & Specification QTY SA/SNA REMARK
F0005 DC47-00017A THERMOSTAT;60T21,-,250V,15A/25A,-20~150, 1 SA
A0376 DC97-07602B ASSY-DUCT CONE;MDG9700AWW,GAS/ENTRY 1 SA
Z0050 6002-000231 SCREW-TAPPING;TH,+,-,2S,M4,L12,ZPC(YEL), 3 SA
A0377 DC67-00136B DUCT-CONE(F);WINGS-DRYER,AL-COAT,T0.6,-, 1 SA
A0378 DC67-00137B DUCT-CONE(B);WINGS-DRYER,AL-COAT,T0.6,-, 1 SA
9-1
<1#EORFN#GLDJUDP
9-2
Memo
10-1
431#ZLULQJ#GLDJUDP
10-2
Memo
11-1
441#SFE#GLDJUDP
561
81
71
2
1
4
3
6
7
8911
01
31
21 41 51
4404#PDLQ#SFE#OD\RXW
Item Part Number Description
1 Display
Displays or indicates opera-
tions or
functions
2 Jog_Dial
Starts/stops an operation to
select a
course
3 Power_key Turns the power on/off
4 Key Selects and processes each
function
5 CN1 Detects if the door is open
or closed
6 RELAY1
In case of Power_On/Off,
supplies or
disconnects AC power
7 RELAY2 Disconnects Power from the
Heater
Item Part Number Description
8 CN3 AC1과 GND를 연결함
9 RELAY3 Motor의 정/역 방향을 제어함
10 CN4 Motor의 동작 Wire를 연결함
11 RELAY4 고 RPM진행시 On/Off 제어함
12 CN6 Heat Sink의 온도Sensor를
연결함
13 CN7 수위,온도Sensor를 연결함
14 구동부 냉/온/Pre/Drain 동작용 부품
Item Part Number Description
15 Door System Parts for Door Lock/Unlock
16 CN10 Connects Motor Tacho
Sensor
17 CN8 Connects the silver nano
wire
18 CN9 Connects the driving system
wire
11-2
4405#Frqqhfwru#)#Uhod|#Whuplqdov#Ghvfulswlrq#+PDLQ#SFE,
ڞکڔ
ྙڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڟڭڜڤکڈڨڪگڪڭ
ྚڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڞڪڧڟ ڱڜڧڱڠ
ྛڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ګڭڠ ڱڜڧڱڠ
ྜڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڣڪگ ڱڜڧڱڠ
ྞڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڭڪڧڟ ڟڪڪڭ ڮڊڲ
ڞکڒ
ྙڞۊۉۉۀھۏێ ۏۊ ڢڪڭڰکڟ
ྚڞۊۉۉۀھۏێ ۏۊ ڐڱ
ྛڞۊۉۉۀھۏێ ۏۊ ڐڱ
ྜڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڲڜگڠڭ
ڮڠکڮڪڭ
ྜྷڞۊۉۉۀھۏێ ۏۊ ۏۃۀ گڠڨګ
ڮڠکڮڪڭ
ڞکڑ
ྙڞۊۉۉۀھۏێ ۏۊ ۏۃۀ گڠڨګ
ڮڠکڮڪڭ
ྜڞۊۉۉۀھۏێ ۏۊ ۏۃۀ گڠڨګ
ڮڠکڮڪڭ
ڞکڌ
ڜڄڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڟڪڪڭ
ڧڪڞڦ ڮۄۂۉڼۇ
ڝڄڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڟڪڪڭ
ڧڪڞڦ ڮۄۂۉڼۇ
ڞکڌڋ
ڜڄ ڞۊۉۉۀھۏێ ۏۊ ۏۃۀ
گڜڞڣڪ ڮڠکڮڪڭ
ڝڄ ڞۊۉۉۀھۏێ ۏۊ ۏۃۀ
گڜڞڣڪ ڮڠکڮڪڭ
ڞکڏ
ྙڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڨڪگڪڭ ڮگڜگڪڭ
ྛڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڨڪگڪڭ ڮگڜگڪڭ
ྜڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڨڪگڪڭ ڮگڜگڪڭ
ྜྷڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڨڪگڪڭ ڮگڜگڪڭ
ྞڞۊۉۉۀھۏێ ۏۊ ۏۃۀ ڨڪگڪڭ ڮگڜگڪڭ
ڞکڎ
ྚڞۊۉۉۀھۏێ ۏۊ ڜڞڌ
ྛڞۊۉۉۀھۏێ ۏۊ ڢڭڪڰکڟ
ڞکړ
ྙڞۊۉۉۀھۏێ ۏۊ ڮڤڢڈڜ
ྚڞۊۉۉۀھۏێ ۏۊ ڮڤڢڈڝ
ྛڞۊۉۉۀھۏێ ۏۊ ڤڣ
ྜྷڞۊۉۉۀھۏێ ۏۊ ګڲڨ
ྞڞۊۉۉۀھۏێ ۏۊ ڢڭڪڰکڟ
ڭڠڧڜڴڌ
ڜڄڞۊۉۉۀھۏێ ۏۊ ڜڞڍ
ڝڄڞۊۉۉۀھۏێ ۏۊ ڜڞڍڈڌ
ڞڪڨڨڪک
ڭڠڧڜڴڍ
ڜڄڞۊۉۉۀھۏێ ۏۊ ۏۃۀ
ڣڠڜگڠڭ
ڝڄڞۊۉۉۀھۏێ ۏۊ ۏۃۀ
ڣڠڜگڠڭ
11-3
4406#Frqqhfwru#)#Uhod|#Whuplqdov#Ghvfulswlrq#+DJ0NLW#SED,
ڞکڌ
ྙڞۊۉۉۀھۏێ ۏۊ ڜڞڌ
ྛڞۊۉۉۀھۏێ ۏۊ ڜڞڍ
ڞکڒ
ྙڞۊۉۉۀھۏێ ۏۊ ڢڪڭڰکڟ
ྚڞۊۉۉۀھۏێ ۏۊ ڤڣ
ྛڞۊۉۉۀھۏێ ۏۊ ګڲڨ
ྜڞۊۉۉۀھۏێ ۏۊ ڮڤڢکڜڧڈڝ
ྜྷڞۊۉۉۀھۏێ ۏۊ ڮڤڢکڜڧڈڜ
ྠڞۊۉۉۀھۏێ ۏۊڜڢڈڝ
ྡڞۊۉۉۀھۏێ ۏۊ ڜڢڈڜ
11-4
Memo
12-1
12. SCHEMATIC DIAGRAMS
* This Document can not be used without Samsung’s authorization.
4504#PDLQ#SFE
12-2
* This Document can not be used without Samsung’s authorization.
4505#VXE#SFE
13-1
461#FLUFXLW#GHVFULSWLRQV
46041#RYHUDOO#V\VWHP
13-2
45051#DF#Lqsxw#)#Srzhu#Flufxlw
▶ Function
Generates a required DC power of 12V or 5V in case of supplied or disconnected
AC power.
▶ Description
- When AC 220V is applied to CN3, D17 D20 transforms it to DC 300V.
- DC 300V is generated for the LVT1 secondary source by IC3 and PC1
turning on/off.
- The secondary 12V depends on the ZD1 value.
- The 12V for the LVT1 secondary source is transformed to DC 5V through IC4
13-3
45061#Gulylqj#V|vwhp#Flufxlw
▶ Function
Controls each driving system (VALVE, DOOR S/W, DRAIN-MOTOR) by turning RELAY or
TRIAC on/off.
▶ Description
- MICOM outputs a high signal of 5V from pin # 1 - 7 of IC7 and IC9. 　
- Then, pin # 10 to 16 of IC7 and IC9 are electrically grounded (0V).
- When pin # 10 to 16 are grounded, this creates an electric potential difference from
the 12V that turns on RELAY 5,6,7 and TRIAC2,3,4,5.
- The operating parts (VALVE, DRAIN-MOTOR, DOOR S/W) connected to CN9 turn on if
they are supplied with power.
13-4
45071#Prwru#Flufxlw
▶ Function
Supplies power to the motor and turns it CW/CCW (Right / Reverse direction).
▶ Description
- The operation of TRIAC1 is the same as that of the driving system.
- If the electric potential of R48 is grounded (0V), TRIAC1 turns on.
- CN1 detects if the door is locked or unlocked. If unlocked, it does not apply power to the motor
even if TRIAC1 turns on.
- If the door is unlocked and TRIC turns on, the motor connected to CN4 is supplied with
power and drives CW (right direction).
- Under such conditions, turning RELAY3 on will drive the motor CCW (reverse) as the
wiring is switched to CCW.
- Turning RELAY4 on will switch the winding of the motor to one for higher driving.
13-5
45081#Vhqvru#Ghwhfwlrq#Flufxlw
▶ Function
Detects signals from the sensor and controls the current system.
▶ Description
- The water level sensor is connected to pin 4 of CN7.
- The frequency of the level sensor changes according to the water amount in the tub.
- Then, the frequency is input to MICOM pin 48 for detecting the water amount.
- The DHSEH sensor is connected to CN7 pin 5 and CN6 pins 3,4.
- The resistance of the temp. sensor changes according to the ambient temperature. The
changed resistance is applied to R50 and R51.
- The voltage applied to R50 and R51 is decided according the temp. MICOM stores
the value.
- When voltage is applied to MICOM pins 22 and 23, MICOM compares it to the predefined
one before detecting the current temp.
13-6
45091#Prwru#WDFKR#Lqsxw#V|vwhp
▶ Function
Detects the current RPM of the motor and controls the output.
▶ Description
- The motor TACHO sensor is connected to CN10 B-pin.
- According to the current RPM of the motor, a square wave is applied to pin 8.
- The square wave that is input to TR2 BASE turns the motor on if high (5V), and turns it
off if low (0V). And this operation will be inverted to TACHO NET for a clear wave with no
noise.
- The signal is applied to MICOM pin 13. Then MICOM counts the frequency of the input signal
and detects the current RPM of the motor.
13-8
Memo
14-1
471#UHIHUHQFH#LQIRUPDWLRQ
47041#PRGHO#QDPH
14-2
47051#WHUPLQRORJ\
1) ASSY-MAIN PCB (Imbalance Sensor)
→ To prevent the laundry from gathering on one side of the tube causing noise and vibration, the
washing machine uses an imbalance detection device that evenly disentangles the laundry
before the hydrating cycle starts.
2) DOOR-LOCK S/W
→ Prevents the door from being opened while a cycle is in progress. For safety purposes, it
keeps the door locked even in pause mode or after the washing cycle unless the water level
frequency is greater than 24.8Khz (anti-overfl ow level) or the inside-tube temperature is less
than 65℃ in the hydrating cycle, and 55℃ in the washing cycle.
3) SENSOR-PRESSURE (Anti Over-Flow)
→ When the water supplied is more than 2/3 of the tube capacity due to a malfunction of the
water supply valve, this device automatically starts water-draining and displays “OVER-
FLOW ERROR(E3)” on the LED.
4) THERMISTOR
→ Keeps sensoring and controlling the temperature inside the tube to keep it below your settings.
5) ASSY-THERMAL FUSE (Anti Over-Heat)
→ When the washing heater is overheated due to an error in the thermistor or any other
malfunction, the assy-thermal fuse (built in the heater) is automatically activated to discon
nect the power for your and the product’s safety.
6) ASSY-MAIN PCB (Sensitive Laundry Protection)
→ To avoid any damage to sensitive laundry, the tube temperature is detected and
“ERROR(E8)” is displayed on the LED for Wool or Lingerie courses when the temperature is
over 50䦿.
7) THERMOSTAT (Anti Over-Heat)
→ When the heater (drier) overheats from an error in the thermistor or any other malfunction, the
thermostat (installed on the drying duct) is automatically activated to disconnect the power for
your or product’s safety
8) CHILD LOCK
→ Prevents children from playing with the washing machine.
14-3
<,## SUH0ZDVK
→ The machine does a preliminary wash of about 10 minutes prior to the main wash. This is
particularly effective for cleaning badly stained laundry.
43,##ZHLJKW#VHQVRU
→ The tube automatically rotates when no water is supplied to detect the laundry weight so that
the proper wash time can be determined. (Standard, Boiling, Economy Boil and Dirt courses
and Toweling and Drying cycles)
14-4
47061#IDEULF#FDUH#FKDUW
Resistant material
Delicate fabric
Item may be washed at 95˚C
Item may be washed at 60˚C
Item may be washed at 40˚C
Item may be washed at 30˚C
Item may be hand washed
Dry clean only
Can be bleached in cold water
Do not bleach
Can be ironed at 200˚C max
Can be ironed at 150˚C max
Can be ironed at 100˚C max
Do not iron
Can be dry cleaned using any
solvent
Dry clean with perchloride, lighter
fuel, pure alcohol or R113 only
Dry clean with aviation fuel, pure
alcohol or R113 only
Do not dry clean
Dry flat
Can be hung to dry
Dry on clothes hanger
Tumble dry, normal heat
Tumble dry, reduced heat
Do not tumble dry
44071#HOHFWULFDO#ZDUQLQJV
To reduce the risk of fi re, electrical shock, and other injuries, keep these safety precautions in mind:
- Operate the appliance only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power
company.
- Use only a grounded or polarized outlet. For your safety, this appliance is equipped with a polarized alter
nating current line plug having one blade wider than the other.
This plug will fi t into the power outlet only one way. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug still doesn’t fi t, contact your electrician to replace your outlet.
- Protect the power cord. Power supply cords should be routed so that they are unlikely to be walked on or
pinched by items placed on or against them. Pay particular attention to cords at plugs, convenience re
ceptacles, and the point where they exit from the unit.
- Do not overload the wall outlet or extension cords. Overloading can result in fi re or electric shock.
14-5
NO. Type Part Situation Solution
method
Before consulting cause Management
1 DRUM
WASHER
(MODE
NAME :
Q1*3*)
appear
ance part
Being opened & closed
bad/Being attached &
detached bad
AS rere
commended
In case of
a cover not
being
opened
or closed
- Door is not opened during washing. For models
applied with the boiling or drying the door will not
open until the interior temperature decreases
to a certain safe level. In other cases you are
recommended our engineer’s inspection.
2 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
appear
ance part
Label(sticker) being
detached
consulting …for the specifi ca
tion or label of
product lead the
customer to attach
diretly or send the
engineer to do so.
For other advertise
ment or PR label it
may not be at
tached.
- Is it the label for advertisement? Is it the label
for standards or attentions? -If it is for advertise-
ment it does not matter for the function or the
use even though it is not attached since it is not
related to the function and use. -If it is for st
3 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
appear
ance part
Accessories being not
included
AS rere
commended
..Check whether the
componets are
same as those in
the manual. If not
contact to SVC.
- Sir we really apologize to you for the inconven-
ience that we made from our product which was
bought by you on the basis of your trust in us.
We will try our best to clear your inconvenience
(by mail).
4 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
appear
ance part
Color coming off/rust AS rere
commended
It may be oc
curred when
the machine
is installed in
the humid
place which
causes the
rust or dis
coloring.
- Being rust or being discolored during the use
is normal and natural according to the times and
its use.(except the case occurred at the innitial
purchase). The replacement of case will be
charged and in order to prevent the corrosion
change the location
5 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
display
part
Display part being not lit
up/ not being cleared
AS rere
commended
It is a
symptom
occurred
when it is in
stalled in the
humid place
or the water
is entered its
inside.
- Dry the front operation part a little with the
drier and you are recommended our engineer’s
inspection if it does not work even after doing so.
6 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
display
part
Character being broken
on display
AS rere
commen
ded
- In this case you are recommended our
engineer’s inspection.
7 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
display
part
Display not being cleared AS rere
commen
ded
- In this case you are recommended our
engineer’s inspection.
8 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
display
part
Display malfunction AS rere
commen
ded
- In this case you are recommended our
engineer’s inspection.
9 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
door re
lated
Door sensor not being
detected
Others - In this case you are recommended our
engineer’s inspection.
10 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
a noise A noise being occurred
intermittently during
washing
General
consulting
Please check
whether a
washer is
installed and
used with
removing
the safety
device posi
tioned at its
rear.
- You are recommended our engineer’s inspec-
tion if the safety device is removed and there is
no foreign material such a coin or pin inside.
47081#T#)#D
14-6
11 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
a noise A noise being occurred
intermittently during
dehydrating
General
consulting
..Make a comment
for the customer
to prepare the
memorandum since
he can not be
famaliar with the
contents comple
tely.
Did you
remove the
washer safety
device? It
may be
occurred
when the
laundry is
leaned to
one direction
or the
machine
is not aligned
horizontally
or the foreign
material is
entered.
- Please check whether the machine-installed
place is not leaned to one direction and then
level it and then check whetehr there is no fo-
reign material inside such a the coin or pin. If the
noise occurs without any problem in the machine
a check is requir
12 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
a noise A noise to touch other
parts
General
consulting
..Make a comment
for the customer
to prepare the
memorandum since
he can not be
famaliar with the
contents comple
tely.
It may be
occurred
when the
laundry is
leaned to
one direction
or the
machine
is not aligned
horizontally
or the foreign
material is
entered.
- Check whether the machine-installed place
is not leaned to one direction and then align it
horizontally and then check whetehr there is no
foreign material inside such as the coin or pin.
If the noise occurs without any problem in the
machine. Inspectio
13 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
a noise A noise of Motor AS rere
commen
ded
Noise during water
darainage -roaring
sound
You are rerecommended our engineer’s inspec-
tion because there may be a problem on the
components.
14 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
a noise A noise being occurred
during water supply
General
consulting
The foreign
material
may be
inserted
inside the
water supply
hose or the
pressure of
water may be
too high or
too weak.
- In case that there is a noise during water sup-
ply open or close the tap little by little to adjust
the water pressure to the proper level. If a noise
occurs continuously disconnect the water supply
hose connected to the machine and check
whether there
15 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
a noise Water leakage being oc
curred at water supply
connection
General
consulting
Lead to re
assembe
when water
supply hose
is departed.
Disconnect the water supply hose and reas-
semble.
16 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water le
akage
related
Water being overfl o
wed from detergent
box(front loading wa
shing machine)
General
consulting
It may be
used with so
much de
tergent or
left alone
for a long
time without
use.
- If the detergent input is impossible insert a
proper amount of detergent inot the detergent
box and if it is clogged take out the box forward
and clean it.
17 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water le
akage
related
Water bein leaked to
fl oor
General
consulting
It is a
symtom
occurred
when the
hose of bot
tom not
outside is
departed or
torn off.
- Check the machine for the water drainage rou-
te under the machine. If the water drains through
the other side not the drainage side check by
the engineers.
18 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water le
akage
related
water being leaked at
water supply connec
tion part
General
consulting
It may be
occurred
when it is
pushed out
due to the
water pres
sure or it has
bad connec-
tion.
- Disconnect the coupler and reassemble it. It
had better to assemble by yourself because the
engineer’s visit for service will be additionally
charged in case of diffi cut installation by custo-
mer. In case of the damage or missing of coupler
you can buy i
19 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
leakage
related
Water leakage being
occurred during water
supply
General
consulting
The leakage
during water
supply can
occur
possibly due
to the bad
connection
of tap and
coupler and
water supply
hose.
- First re-assemble the coupler and then check
by the engineer if it continues.
14-7
20 DRUM
WASHER
(MOEL
NAME
:Q1*3*)
water le
akage
related
Natural
drain(continually)/water
not fi lling tub
General
consulting
It can be
appeared at
the drum
washing ma
chine of
which the
drain hose
is located
at the
bottom.
- For the machine having the drain hose at the
below of that raise the drain hose up and fi x it
to the fi xer at 2/3 point of the machine. If the
hose is used at the fl oor all water supplied will
drain fully.
21 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
smell/
smoke
Burning smell General
consulting
For the initial
use of
product
It may appear
during the
operaiton
with coupling
each other
but it
carefully
watched
by the
customers
who are
using more
than for 3
years.
- Is that a newly bought one?
- A smell is disappeared after 4~5 days passed
in case of newly bought one but it depends upon
the frequency of use. Be sure to use it without
worry. If is not disappeared contact a engineer
22 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
smell/
smoke
Burning/smoke General
consulting
Pull out the plug in
case of smoke or
fi re.
It can be
shown in
case that the
interior
components
of the
products do
not work
normally.
- In this case you are recommended our
engineer’s inspection.
23 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
power
soruce
related
Power not supplied AS
rerecom
mended
It can be
shown in
case that
the power
cord is not
inserted or
electricity is
blacked out
or the interior
components
of the
products do
not work
properly.
- Take out the power cord and put it in again and
check whether the power for the other products
is on. If it is not even after that you are recom-
mended our engineer’s inspection.
24 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
power
soruce
related
Current leakage breaker
being dropped
General
consulting
It may be
occurred when
the humidity is
full inside the
machine.
- In this case you are recommended our
engineer’s inspection.
25 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
power
soruce
related
Autmatic stop during
operation
AS rerecomm
ended
It may be
occurred when
there are too
much laundry.
-Reduce the contents to be washed. If it
continues you are recommended our engineer’s
inspection.
26 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
power
soruce
related
Being power off frequently AS rerecomm
ended
It may be
occurred in
case of the
bad contact of
button.
- In this case you are recommended our
engineer’s inspection.
27 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
operation
related
Button being not operated Consulting It may be
occurred
when the
accumualtion
of foreign
material or
moisture
ingress into
the button.
- In this case you are recommended our
engineer’s inspection.
28 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
operation
related
Being not rotating during
washing
AS rerecomm
ended
It may be
occurred when
the water
supply not
completed
or the cover
not closed
completely
or the
accessories of
products have
a abnormallity.
- First check whether the tap is open and the
cover closed and then request an engineer’s
inspection.
14-8
29 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
4E :front
loading
washing
machine
error
Water level sensor
inferiority
AS rerecomm
ended
This may be
happened
when there
is any foreign
material inside
the water
supply and
drain valve
or the interior
components of
the prodcuts
do not operate
normally.
- Water
level sensor
or mother
rotation.
- Disconnect the water supply hose and check
whether there is a foreign material inserted in it.
And then request an engineer’s inspection.
30 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
5E :front
loading
washing
machine
error
Water being not drained AS rerecom-
mended
It may be
occurred when
the drain hose
is go over the
threshold or
water is not
drained.
It may eb
occurred when
the The fi lter
of pump-drain
moder is fulled
with dregs,
Check the installation of drain hose and then
if there is no trouble request an engineer’s
inspection.
Clean the fi lter of pump-drain motor. Guided by
instruction-manual.
31 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
OE :front
loading
washing
machine
error
3E OVER-FLOW General
consulting
It may be a
case that the
supply water
level is not
detected.
- After Draining the water power off and on and
operate again. If it dose not work after so doing
request an engineer’s inspection.
32 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
UE :front
loading
washing
machine
error
4E UNBALANCE ERR General
consulting
It may be hap-
pened when
the fl oor of the
installed palce
is not fl at or
the clothes are
entangled.
Level the machine or arrange the entangled
clothes. If it does not worked even after so doing
request an engineer’s inspection.
33 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
HE1 : front
loading
washing
machine
error
E5 WATER HEATER ERR General
consulting
It may happen
when the
boiling tem-
peratuer rised
rapidly. (It is
also because
too much
detergent are
used.)
Use the proper amount of detergent and power
off the machine till the temperaure is cooled
down.
And if it does not work even after so doing
request an engineer’s inspection.
34 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
HE : front
loading
washing
machine
error
E6 WATER HEATER ERR AS rerecom-
mended
It may appear
when it dose
not reach to
the set tem-
perature within
a certain time.
- In this case you are recommended our
engineer’s inspection.
35 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
1E :front
loading
washing
machine
error
E7 Water level sensor
ERR
AS rerecom-
mended
It may happen
when there is
a trouble in air
hose or water
level sensor.
- In this case you are recommended our
engineer’s inspection.
36 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
cE : front
loading
washing
machine
error
E8 Abnormal water tem-
perature ERR
AS rerecom-
mended
Check
whether the
hose for hot
and cold water
is connected
to the water
supply hole.
- Check whether the cold water is supplied
through the cold water supply hole and if
it doesn’t work after so doing request an
engineer’s inspection.
37 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
8E : front
loading
washing
machine
error
E9 Water leakage ERR AS rerecom-
mended
Check
whether there
is foreign ma-
terial inserted
in the drain
fi lter.
- In this case you are recommended our
engineer’s inspection.
38 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
tE :front
loading
washing
machine
error
E9 Water leakage ERR AS rerecom-
mended
Check
whether there
is foreign ma-
terial inserted
in the drain
fi lter.
- In this case you are recommended our
engineer’s inspection.
14-9
39 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
11E : front
loading
washing
machine
error
E9 Water leakage ERR AS rerecom-
mended
Check
whether there
is foreign ma-
terial inserted
in the drain
fi lter.
- In this case you are recommended our
engineer’s inspection.
40 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
door : front
loading
washing
machine
error
Ed:Door being not opened AS rerecom-
mended
It may appear
when the the
door is opened
a certain
minutes after
the completion
of washing or
the electricity
is interrupted
in running.
Check of Bad
contact of 1st
door opening
sensor----
*check of
the bending
of 2nd door
switch*Do not
open the door
-There is a cover dettachable at the front bot-
tom. Pull out the cover to fi nd the handle to open
at the right side. Pull out the handle to open
the door.
41 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
front
loading
washing
machine
error
E6:Overheating error AS rerecom-
mended
It may appear
when the
temperarture
rises rapidly.
- In this case you are recommended our
engineer’s inspection.
42 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Cold water being not
supplied
General
consulting
- Check fi rst whether the water supply is cut
and also check whether the foreign material is
inserted. If the foreign material is inserted turn
the connection hose of machine to the left to
disconnect and to fi nd the strainer to trap the
foreign material.
43 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Water being supplied little General
consulting
It may appear
when the tap
is not opened
properly or
there is a for-
eign material
inside.
- Is it checked whether the tap is fully open
or there is a foreign material inserted? - First
check whether the tap is fully open. And there is
no fault turn the hose of the machine to the left
to take out strainer in the hole of water entrance.
Clean i
44 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Detergent being remained General
consulting
It may appear
when the long-
term used
detergent is
not well sol-
uted or when
the water
temperature
is low during
winter.
- Sove the detergent wth the hot water and put it
inot the washing box.
If it is not solved even with the normal detergent
request an engineer’s inspection.
45 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Water being stopped dur-
ing the coming in
General
consulting
It may appear
when the
water is cut
or the water
supply hole is
clogged.
- Is it checked whether the water is cut or there
is a foreign material inserted in the water supply
hole? -First check whether the water is cut and
if there is a blackout push the power button on.
Otherwise turn the machine hose to the left to
take out t
46 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Clothes being damaged General
consulting
- In this case you are recommended our
engineer’s inspection.
47 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
One direction rotation - In this case you are recommended our
engineer’s inspection.
48 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Rotation being not worked
after it sounds with buzz
- In this case you are recommended our
engineer’s inspection.
49 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
supply
related
Water being not supplied
in winter
It may appear
when the tap
and the water
supply hose
are frozen if it
is used at the
veranda in the
winter.
- Make the water supply hole warm and defreeze
it with wet towel.
14-10
50 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
rinsing
related
Rinse being not put in tub General
consulting
It may appear
when the rinse
agent remains
to clog .
-Did the rinse agent drain immediately or part
to put the rinse is clogged after putting the rinse
agent? - The rinse agent does not drain only
when putting it up to the reamer shaped cap
which is in the box of rinse agent. If clogged take
out the cap and
51 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
rinsing
related
Bubble being remained General
consulting
It may appear
when there
is too much
or too little
laundry.
- If there is too much laundry or vinyl clothes the
detergent is not solved. Reduce the laundry or
take out the vinyl clothes separately.
52 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
drain
related
Water being not drained General
consulting
- In this case you are recommended our
engineer’s inspection.
53 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Dehydrating time being
increased again
General
consulting
..Make a comment for
the customer to pre-
pare the memoran-
dum since he can not
be famaliar with the
contents completely.
The vibration
and noise
occur when
the horizon is
broken or the
laundry are
leaned to one
direction. So
It may appear
when the
safety device
is operating to
prevent it.
- If there is too little laundry less than 1KG or
the clothes in the washing tub are severely
entangled it appears.
54 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Washer being worked
for four hours without
stopping
Specifi c
consulting
If the washing
machine
consumes
hours more
than neces-
sary check
whether the
water supply
is too small.
And note that
that the boling
and the drying
course takes
much time.
- Check whether the water supply time is too
much delayed due to the low pressure of water
or boiling or drying is selected. In other cases
request an engineer’s inspection.
55 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Not dehydrating with the
motor being purring after
water is drained
General
consulting
The power
cord for motor
may be cut or
the gear shaft
hardened.
- In this case you are recommended our
engineer’s inspection.
56 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Being stopped with thuds
during dehydration
AS rerecom-
mended
..Make a comment for
the customer to pre-
pare the memoran-
dum since he can not
be famaliar with the
contents completely.
It may ap-
pear when
the horizon
is broken or
there are too
much clothes
to wash.
- check the level of a washing machine.
57 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Not being squeezed well General
consulting
It may appear
when there
are clothes
like vinyl.
-Check whether the vinyl clothes are attached on
to the washing tub so as to prevent the immedi-
ate the outgoing of the moisture to the outside.
Otherwise request an engineer’s inspection.
58 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Water being in at purchas-
ing
AS rerecom-
mended
- There may be remaining water since the prod-
ucts is delivered thorugh the fi nal products test.
It is normal and you can use it without fear.
59 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Dehydration being not
worked at all
General
consulting
It may ap-
pear when
the interior
components
do not work
properly.
- In this case you are recommended our
engineer’s inspection.
60 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
others Action for water being
freezen in winter
AS rerecom-
mended
It may appear
when the
machine is
used at the
outside or the
veranda.
- pour the warm water on to the tap to take out
the water suppy hose and put the hose in to the
water of approximately 50 degree. And then pour
the water in to the washing box to check whether
the drain is well done.
61 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
others being clogged/foreign
materials
General
consulting
….the drainage hose
clogged or foreign
material inside
- After loosening the water supply hose and
check the inlet of water supply whether there is
foreign material inserted such a soil dust.
14-11
62 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
installation
/ connec-
tion
Consulting for installation
of front loading washing
machine
General
consulting
- The drum washing machine is leveled after
removing the safety device at the rear of drum.
And for a removing the safety device refer to
accessories and user’s manual.
63 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
installation
/ connec-
tion
Level check Specifi c
consulting
- Level it by use of a leveller(with a coin weight)
at the front.
64 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
installation
/ connec-
tion
Removal/house moving
reinstallation
Specifi c
consulting
-It is possible to remove and install in the house
but when moving to the other house and install-
ing it assemble the safety device at the back
while moving and remove it after moving. If the
drum is shaken during the moving it causes a
serious damage.
65 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
washing
related
Slow speed of washing
rotation
General
consulting
It may appear
when there
is too much
laundry.
- Check whether the laundry is input over the
proper amount. Otherwise request an engineer’s
inspection.
66 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
washing
related
Clothes being damaged General
consulting
Check
whether there
is foreign
material inside
(coin nail and
other sharp
material) and
so it may
appear due
to the zipper
or button of
jeans.
- Check whether there is foreign material in the
washing tub. In case of dehydrating the weak
material cothes it shall be inserted in the net
during dehydrating. Any other cleaning agent
(decoloration agent) shall not be used except the
detergent and rins
14-12
Memo
Notes:
Be Aware, Be Alert
Always work safely.
On the Job, On the Road, In the Home
Every Time, All the Time
Maytag Technical Institute 34

Navigation menu