Mb Quart Pvl216 Users Manual MBQ Premium Speaker Front Cover
PVL PVL
PVL268 MBQuartPremiumPVLSeriesSpeakerManual
PVL216 to the manual 73687dab-d05c-4f5f-bd1f-1de6279672bb
2015-02-09
: Mb-Quart Mb-Quart-Pvl216-Users-Manual-554467 mb-quart-pvl216-users-manual-554467 mb-quart pdf
Open the PDF directly: View PDF .
Page Count: 10
Download | |
Open PDF In Browser | View PDF |
www.mbquart.com PREMIUM PVL216 / PVL268 / PVL269 Thank you for choosing MB Quart Premium speakers for your car audio sound system. With proper installation, you are on the path to experiencing your music in a way you only imagined possible. Here at MB Quart, we call this “Sound In Every Detail.” The Premium series speakers have been designed for the enthusiast looking for incredible sound and amazing performance. The Premium series speakers feature the following: - Convertible Coax/Component Capability - 40mm Silk Dome Tweeter - Gold Plated Speaker Terminals - Active Crossover With Variable Tweeter Attenuation And Gold Plated Terminals - Edge Rolled Steel Basket - Spider Woven Tinsel Leads - Motor Damping Magnet Cap - Progressive Long Travel Spider - Progressive Grill - High Energy Magnet - Polypropylene Cone PREMIUM PVL216 / PVL268 / PVL269 Side View Of PTL-40 2.4” 1.95” .37” .63” .41” 1.58” 2.13” Top View Of PXO 2.76” 4.72” Side View Of PXO 1.24” PVL216 2.53” 3.59” 7.24” 5.61” 70 140 70 140 4 70 4 87 38 - 32,000 87 38 - 32,000 140 4 87 38 - 32,000 40mm 16cm 40mm / 1.58” 16cm / 6.5” 40mm / 1.58” 16cm / 6.5” 2 X-Overs 70 140 4 87 38 - 32,000 40mm 16cm 70 140 4 87 38 - 32,000 70 140 87 38 - 32,000 40mm 16cm 40mm 16cm PVL268 8.05” 5.81” 2.38” 3.38” 7.36” 5.11” 40 80 40 80 4 40 4 87 38 - 32,000 87 38 - 32,000 40mm / 1.58” 5x7” / 6x8” 40mm / 1.58” 5x7” / 6x8” 80 4 87 38 - 32,000 40mm 5x7” / 6x8” 2 X-Overs 40 80 4 87 38 - 32,000 40mm 5x7” / 6x8” 40 80 4 87 38 - 32,000 40 80 87 38 - 32,000 40mm 5x7” / 6x8” 40mm 5x7” / 6x8” PVL269 8.05” 5.81” 3.38” 2.38” 7.36” 5.11” 50 110 50 110 4 50 4 88 32 - 32,000 88 32 - 32,000 110 4 88 32 - 32,000 40mm 6x9” 40mm / 1.58” 6x9” 40mm / 1.58” 6x9” 2 X-Overs 50 110 4 88 32 - 32,000 40mm 6x9” 50 110 4 88 32 - 32,000 50 110 88 32 - 32,000 40mm 6x9” 40mm 6x9” PREMIUM PVL216 / PVL268 / PVL269 We strongly recommend that you have your new Premium series speakers installed by your authorized MB Quart dealer. The installation professionals employed by your dealer have the necessary tools and experience to disassemble your vehicle, install your new speakers and reassemble everything properly. If you prefer to perform your own installation, it is very important that you read the entire manual first. GETTING STARTED: - Turn off the audio system. - Check clearance on both sides of mounting surface to ensure that there are no obstructions (windows, tracks, wiring etc). CROSSOVER NETWORK INSTALLATION: - Locate a dry location for mounting of your Premium Crossover Networks. DO NOT MOUNT IN DOORS! - Remove the cover of the crossover by squeezing either side. This exposes the mounting holes for securing the crossover to a flat surface. Prior to pre-drilling pilot holes, ensure that you will not be drilling into wiring, gas tanks, fuel lines etc. - Once the crossover is mounted, snap the protective cover back in place. INPUT IN+ | IN- MID BASS WF+ | WF- VARI-TWEETER TW+ | -6dB | -3dB | 0dB WIRING THE PREMIUM CROSSOVER INPUT IN+: Connect positive speaker wire from radio or amplifier. IN-: Connect negative speaker wire from radio or amplifier. MID BASS WF+: Provides positive output to midrange speaker. WF-: Provides negative output to midrange speaker. VARI-TWEETER TW+: Provides positive output to tweeter. -6dB: Provides negative output to tweeter at -6dB. -3dB: Provides negative output to tweeter at -3dB. 0dB: Provides negative output to tweeter with no manipulation. The negative connection under the VARI-TWEETER section allows for varied degrees of tweeter attenuation. Only connect to one negative terminal with the understanding that 0dB is no manipulation and the loudest selection for tweeter output, -6dB is the quietist selection for tweeter output and -3dB is in the middle. PREMIUM PVL216 / PVL268 / PVL269 Wiring Diagram INPUT IN+ | IN- MID BASS WF+ | WF- VARI-TWEETER TW+ | -6dB | -3dB | 0dB SELECTABLE CLIP INDICATOR AMBERSOFT CLIP REDHARD CLIP GREENPRE CLIP CLIP INDICATOR GREENPRE CLIP LEVEL 9V BASS BOOST 0dB 12dB MULTIPLIER FREQUENCY 9V 0.2V BASS BOOST 0dB X1 12dB BASS FREQUENCY 30Hz X15 AMBERSOFT CLIP REDHARD CLIP LEVEL 0.2V 80Hz HIGH PASS FILTER SLOPE 6dB 12dB 15Hz 1KHz CHANNELS 1&2 CHANNELS 3&4 HIGH PASS LOW PASS (x1) 20Hz (x15) 300Hz 300Hz 4.5KHz CROSSOVER DUPE (3&4) HP-FULL PROTECT POWER 40Hz 4.5KHz CROSSOVER LP-BP LP-BP HP-FULL MONO STEREO INPUT MODE 4CH 2CH - + VERY IMPORTANT TINSEL TO MID BASS CONNECT “WF” WIRE FROM CROSSOVER TO THE SPADE OR SCREW DOWN TERMINAL WITH TINSEL WIRE TO MID BASS NO TINSEL WIRE IF THE TWEETER IS MOUNTED AS A COAXIAL IN THE CENTER OF THE MID BASS, CONNECT THE WIRE FROM THE TWEETER TO THE SCREW CLAMP WITHOUT TINSEL WIRE. THEN CONNECT (The above illustration shows the positive terminal view. “TW” WIRE FROM CROSSOVER The negative terminals are opposite. TO THE SPADE OR SCREW Be sure to identify the tinsel wire for your mid bass.) DOWN WITHOUT TINSEL WIRE PREMIUM PVL216 / PVL268 / PVL269 Tweeter Mounting Options Separate From Mid Bass (Component) Flush Mount Method Top Mounted Method Mounting Surface Mounting Brackets Cup Mounting Screws Mounting Bracket Washers Mounting Bracket Screws Mounting Surface Surface Angle Mount Method Cup Mounting Screws Mounting Surface Tweeter Mounting In The Center Of The Mid Bass (Coaxial) Guide Pin Indents Grille Tweeter Assembly Tweeter Post Assembly Wires Bottom View Of Tweeter Assembly Guide Pins Lock Washer Screw Tweeter Post 1. Place the tweeter grille onto the tweeter assembly to prevent damage to the delicate silk dome 2. Route the red & black tweeter wires through the opening in the top of the tweeter assembly 3. Line up the 4 guide pins on the tweeter post with the 4 indents on the bottom of the tweeter assembly 4. Fasten the tweeter post to the tweeter assembly using the provided screw and lock washer Phase Plug 1. Un-screw the phase plug by turning counter-clockwise and remove 2. Route the tweeter wires through the center of the speaker until they come out the back of the speaker 3. Screw the tweeter post assembly clockwise until snug PREMIUM PVL216 / PVL268 / PVL269 Speaker, Tweeter and Crossover Placement Options: Factory sound systems vary greatly. Some systems have coaxials (tweeter fixed in the center of the midrange) in the door, while others have factory component (tweeter is separate from midrange) systems. If your system has the factory component offering then you will want to locate your factory tweeter mounting location and compare it to the diagram below. Some vehicles already have the tweeter in the ideal location, while others often position the tweeter in the top corner of the door pane which is less than ideal. A good rule of thumb is to try and mount the tweeter within 8 inches of the midrange woofer for optimal imaging and tonal balance. When selecting an optimal mounting location, ensure that you are clear of any obstructions within the door. Cutting or drilling into moving parts or electrical accessory wires can be very dangerous and costly. Woofers should typically be installed in the factory locations. Simply ensure that the new woofer will not obstruct the window or other moving parts in the door. The Crossover should NEVER be mounted in the shell of the door. This can damage the crossover through vibration and moisture which is NOT covered under warranty. The Crossover can be mounted in a kick panel, under a seat or in the trunk as long as the area is not located near any moving parts in the vehicle which could cut or pull the wires resulting in a short circuit. All wiring to and from the crossover should avoid all moving parts in the vehicle which could potentially damage the wiring. Take great care when running wires through the door frame and into the door as wires can easily be cut. A rubber grommet should be used on both holes and wire loom should be wrapped around the exposed wires as shown in the diagram below. Alternate Tweeter Location Crossover Ideal Tweeter Location Mid Bass Route speaker wires through rubber grommet between door jam and door as shown. Use wire loom to protect the wires. www.mbquart.com PREMIUM PVL216 / PVL268 / PVL269 car audio PART#U1010
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2010:11:18 10:45:51-05:00 Create Date : 2010:11:18 10:44:32-05:00 Metadata Date : 2010:11:18 10:45:51-05:00 Creator Tool : CorelDRAW Format : application/pdf Title : MBQ Premium speaker manual front cover Creator : Mike Document ID : uuid:01601795-8a4d-4d6b-856a-372d6108ca94 Instance ID : uuid:e9b6b2f1-1329-41da-a886-4dda6b80c0d9 Producer : Corel PDF Engine Version 3.0.0.576 Page Count : 10 Author : Mike Creation Date--Text : Mod Date--Text :EXIF Metadata provided by EXIF.tools