Mcculloch Pro Mac 54 54Cc Users Manual OM, McCulloch, ProMac 54, 61, 95390009100, 95390009200, 1999 04, Chain Saw
PRO MAC 61 59CC to the manual 37837df6-2964-4912-afe9-9fdd20f9150c
2014-12-13
: Mcculloch Mcculloch-Pro-Mac-54-54Cc-Users-Manual-125031 mcculloch-pro-mac-54-54cc-users-manual-125031 mcculloch pdf
Open the PDF directly: View PDF 
.
Page Count: 13
| Download | |
| Open PDF In Browser | View PDF |
PRO MAC 54 PRO MAC 61 54CC 59CC A. B. C. D. E. F. G. H. I. L. 18”/45cm 68T 3/8” 20”/50cm 72T 3/8” 20”/50cmSP 72T GB DE FR NL NO FI SE DK ES PT IT GR HU 3/8” PRO MAC 54 PRO MAC 61 225735B 225739B 86826B (7/32”) 225735B 225739B 86826B (7/32”) 225736B 225740B 86826B (7/32”) 225736B 225740B 86826B (7/32”) 225737B 225740B 86826B (7/32”) Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice. Im Sinne des Fortschritts behält sich der Hersteller das Recht vor, technische Änderungen ohne vorherigen Hinweis durchzuführen. La Maison se réserve la possibilité de changer des caractéristiques et des données de ce manuel à n’importe quel moment et sans préavis. Door konstante produkt ontwikkeling behoud de fabrikant zich het recht voor om rechnische specificaties zoals vermeld in deze handleiding te veranderen zonder biervan vooraf bericht te geven. Produsenten forbeholder seg all rett og mulighet til å forandre tekniske detaljer i denne manualen uten forhåndsvarsel. Jatkuvan tuotteen parannusohjelman tähden valmistaja pidättää oikeuden vaihtaa ilman ennakkovaroitusta tässä ohjekirjasessa mainittuja teknisiä yksityiskohtia. Tilverkaren reserverar sig rätten att ändra fakta och uppgifter ur handboken utan förvarning. Producenten forbeholder sig ret til ændringer, hvad angår karakteristika og data i nærværende instruktion, når som helst og uden varsel. La firma productora se reserva la posibilidad de cambiar las características y datos del presente manual en cualquier momento y sin previo aviso. A casa productora se reserva a possibilidade de variar características e dados do presente manual em qualquer momento e sen aviso prévio. La casa produttrice si riserva la possibilità di variare caratteristiche e dati del presente manuale in qualunque momento e senza preavviso. Λγω προγράµµατος συνεχούς βελτίωσης προϊντων, το εργοστάσιο επιφυλάσσεται του δικαιώµατος να τροποποιεί τις τεχνικές λεπτοµέρειες που αναφέρονται στο εγχειρίδιο αυτ χωρίς προηγούµενη ειδοποίηση. Folyamatos gyártmány felùjítási müsorunk következtében, a gyártó cég fenntartja a jogát ebben a Használati leirt müszaki adatok elözetes értesítés nélküli változtatására. THIS PRODUCT MEETS THE SAFETY STANDARD REQUIREMENT OF THE EUROPEAN MACHINERY DIRECTIVE DISPLACEMENT (cm ) ................................................................................................................ BORE AND STROKE (mm).......................................................................................................... ENGINE OUTPUT (kW)................................................................................................................ ENGINE SPEED AT MAX POWER (min-1) .................................................................................... MAXIMUM SPEED (min-1) ............................................................................................................ MINIMUM SPEED (min-1) ............................................................................................................. DRY WEIGHT (Kg) (NO BAR AND CHAIN) .................................................................................. CHAIN PITCH (9,525 mm)........................................................................................................... CHAIN GAUGE (mm)................................................................................................................... BAR LENGTHS (cm).................................................................................................................... No. OF SPROCKET TEETH ........................................................................................................ OIL TANK CAPACITY (cm3) ......................................................................................................... FUEL TANK CAPACITY (cm3) ...................................................................................................... SOUND PRESSURE LEVEL (AT THE OPERATOR’S EAR). LpAav (dBA) (EN 27182 - EN 608) ... SOUND POWER LEVEL LwAav (dBA) (ISO 9207 - EN 608) ........................................................ VIBRATION LEVEL (ISO 7505 - EN 608) (m/s2)............................................................................ SPECIFICATIONS 3 UK 54 45x34 2,6 8.200 11.000 2.500 6,25 3/8” 1,5 45/50 7 390 590 101 109 9,25 QUESTO PRODOTTO È CONFORME ALLA DIRETTIVA EUROPEA SULLA SICUREZZA DELLE MACCHINE CILINDRATA (cm ) .................................................................................................................... ALESAGGIO x CORSA (mm) .................................................................................................... POTENZA (kW)......................................................................................................................... REGIME Dl MASSIMA POTENZA (min-1) .................................................................................. REGIME MASSIMO (min-1) ........................................................................................................ REGIME DI MINIMO (min-1) ....................................................................................................... PESO A SECCO (Kg) (SENZA BARRA E CATENA) ................................................................... PASSO CATENA (9,525 mm) ................................................................................................... SPESSORE CATENA (mm)....................................................................................................... LUNGHEZZA BARRA (cm)........................................................................................................ No. DENTI DEL PIGNONE ........................................................................................................ CAPACITÀ SERBATOIO OLIO (cm3) ......................................................................................... CAPACITÀ SERBATOIO MISCELA (cm3) .................................................................................. PRESSIONE SONORA ALL’ORECCHIO DELL’OPERATORE LpAav (dBA) (EN 27182 - EN 608). POTENZA SONORA LwAav (dBA) (ISO 9207 - EN 608)............................................................ VIBRAZIONI (ISO 7505 - EN 608) (m/s2) .................................................................................. CARACTÉRISTIQUES TECHNIQUES DATI TECNICI 3 I 54 45x34 2,6 8.200 11.000 2.500 6,25 3/8” 1,5 45/50 7 390 590 101 109 9,25 CE PRODUIT EST CONFORME À LA NORME EUROPÉENNE POUR LA SÉCURITÉ DES MACHINES CYLINDRÉE (cm )..................................................................................................................... ALÈSAGE / COURSE (mm)....................................................................................................... PUISSANCE MOTEUR (kW)...................................................................................................... REGIME MOTEUR PUISSANCE MAX (min-1)............................................................................. REGIME MAXIMUM (min-1)........................................................................................................ REGIME DE RALENTI (min-1) .................................................................................................... POIDS A VIDE (Kg) (SANS BARRE NI CHAÎNE) ........................................................................ PAS DE LA CHAÎNE (9,525 mm) ............................................................................................. JAUGE (mm)............................................................................................................................. LONGUEUR DE GUIDE (cm)..................................................................................................... NOMBRE DES DENTS DE PIGNONS....................................................................................... CAPACITÉ DU RÉSERVOIR HUILE (cm3) .................................................................................. CAPACITÉ DU RÉSERVOIR ESSENCE (cm3)............................................................................ PRESSION SONORE À L’OREILLE DE L’OPERATEUR. LpAav (dBA) (EN 27182 - EN 608)...... NIVEAU DE BRUIT LwAav (dBA) (ISO 9207 - EN 608) .............................................................. VIBRATIONS (ISO 7505 - EN 608) (m/s2) .................................................................................. 3 59 47x34 2,82 8.200 11.000 2.500 6,25 3/8” 1,5 45/50 7 390 590 101 109 8,02 59 47x34 2,82 8.200 11.000 2.500 6,25 3/8” 1,5 45/50 7 390 590 101 109 8,02 F 54 45x34 2,6 8.200 11.000 2.500 6,25 3/8” 1,5 45/50 7 390 590 101 109 9,25 59 47x34 2,82 8.200 11.000 2.500 6,25 3/8” 1,5 45/50 7 390 590 101 109 8,02 UK SYMBOL MEANING GENERAL DESCRIPTION A 1 - BAR Read operator’s manual carefully 2 - CHAIN 3 - FUEL TANK CAP 4 - OIL TANK CAP Wear safety clothing: 5 - STOP / RUN LEVER 1 Approved safety glasses or face shield 6 - STARTER HOUSING 2 Approved safety helmet 7 - STARTER HANDLE 8 - FRONT HANDLE 3 Approved ear defender 4 Approved gloves 5 Approved safety footwear 9 - AIR FILTER COVER 10 - SPIKE/SPACER 11 - CARBURETOR ADJUSTMENT SCREWS 12 - SAFETY CHAIN BRAKE 13 - BAR RETAINING NUTS Do not smoke while refuelling or while operating the machine 14 - CHAIN CATCHER 15 - MUFFLER SHIELD 16 - REAR HANDLE Warning - Caution 17 - THROTTLE TRIGGER LOCKOUT 18 - THROTTLE TRIGGER Choke fully opened (hot start /run) 19 - CHAIN BRAKE COVER 20 - CHAIN ADJUSTER SCREW Choke partially opened Choke closed (cold start) Brake engaged / disengaged Beware of kickback Do not cut with the end on the bar, this may cause kickback Never use the machine with only one hand Always use the machine with both hands SAFETY PRECAUTIONS B 1 All operators should read this manual carefully before using this chainsaw; only use this machine for usage specifically mentioned in this manual. Wear suitable clothing. This should include snugly-fitting (safety) clothing, sturdy boots, heavy duty gloves, goggles or a face screen and ear plugs or ear mufflers. Wear a helmet if there is risk of falling objects or projections from trees. 2 Always hold the chainsaw firmly with both hands when the engine is running. Always maintain a firm foothold. Ensure you are able to stop the engine quickly if necessary.Do not work up a tree unless you have received suitable training and have the appropriate equipment (belts, ropes, safety hooks etc.) for this type of work. We strongly recommend that all first-time chainsaw users obtain practical instruction on safe chainsaw usage before operating the chainsaw. Do not operate this machine when tired or under the influence of any substances, drugs or alcohol which can impair vision, dexterity or judgement. Prolonged use of chainsaws or other machines exposing the operator to vibration may produce Whitefinger’s Disease (Raynaud’s Phenomenon). This may reduce the hands’ ability to feel and regulate temperature and may 1 UK 3 4 5 6 produce general numbness. Continual or regular users should therefore monitor closely the condition of their hands or fingers. If any of the symptoms appear, seek immediate medical advice. Never carry the chainsaw with the engine running. Whenever carrying a chainsaw, even for short distances, the chain should be covered by the chain guard (scabbard) and the bar should point backwards. When transporting the chainsaw in a vehicle, secure the saw to prevent fuel spillage. To avoid kick-back, do not attempt to cut with the nose of the bar. Ensure the engine is running at full throttle before commencing to cut. To avoid kick-back, do not let the nose of the bar come into contact with logs, branches, the ground or any other obstruction. Do not allow any part of the chain to come into contact with rock, nails or wire fence Ensure the chain is kept sharp and correctly tensioned. Keep the spike or the saw body against the wood when cutting. Use only genuine accessories and spare parts. We recommend you have your unit periodically checked and serviced by an authorised dealer. Do not use chainsaw above shoulder height. Do not operate the chainsaw near a naked flame or spilled fuel. Only operate the chainsaw outside and in well ventilated areas. After re-fuelling, always wipe off any spilled fuel. Move the chainsaw away from the fuelling point before starting the engine. Keep by-standers and animals out of the work area; at a minimum distance of 10 m or twice the timber length. If necessary, use warning signs to keep on-lookers at a distance. Carefully survey the working site to note any hazards, eg. roads, paths, electricity cables, dangerous trees etc. Do not use the chainsaw if the device for stopping the chain (safety chainbrake) does not work correctly. Never place hands on the chain whilst the engine is running. Ensure someone is within hearing distance in case of an accident. If this is not possible, it is recommended that users operating chainsaws in remote areas carry an adequate first-aid kit with them and ensure someone knows their location. Never leave the engine running while the tool is unattended. ONLY USE ORIGINAL SPARE PARTS AND ACCESSORIES. BAR AND CHAIN INSTALLATION C Ensure engine is always switched off before fitting or adjusting chain. Wear a pair of protective gloves when fitting or adjusting chain. A. Clutch guard B. Inner bar plate C. Bar mounting bolts D. Chain tensioning screw E. Oil hole F. Outer bar plate G. Bar retention nuts H. Sprocket I. Adjusting screw 2 Remove the clutch guard (A) and the outer bar plate (F). Check that the oil hole (E) is free from impurities. Fit the chain over the sprocket (H). Ensure correct direction of cutter tooth. Put the bar in position over studs (C) slide it towards the sprocket. Fit the chain into the bar groove and slide the bar forwards. Make sure that the tang chain tensioning screw (D) fits into the hole in the bar (E). Replace the outer bar plate and the clutch guard. Screw the two bar retention nuts finger tight (G). Tension the chain by turning the adjusting screw (I) clockwise while raising the tip of the bar. The tension is sufficient if the chain is snug on the bar but still moves freely around the bar when pulled by hand. Tighten the two bar retention nuts securely. Always use the combination tool to install and tension the chain. RUNNING IN A NEW CHAIN The chain must always be cold when carrying out adjustment. 1 Let the chain run slowly for a few minutes. Check that the oil pump is delivering oil onto the chain. 2 Stop the engine and adjust the chain tension. 3 Check the tension of a new chain more frequently during initial usage and adjust as necessary. 4 Repeat adjusting until the chain does not stretch any more. Never touch the chain while the engine is running. FUEL MIX D Use only fuel recommended by this manual. This product is fitted with a 2-stroke engine and therefore requires a 2-stroke petrol and oil mix. Use leaded (4 Star) or unleaded petrol with a minimum octane rating of 90. Only use oil from sealed containers. In order to obtain a good fuel mix, put the oil into the container before the petrol. The use of sub-standard petrol or oil may reduce performance or reduce the life of certain components. LEADED PETROL If using leaded petrol, the correct fuel mix is achieved by either using 5% (20:1) of a well known brand of 2-stroke engine oil, or else 2.5% (40:1) of special McCulloch engine oil. UNLEADED PETROL If using unleaded petrol, you must use a totally synthetic 2stroke engine oil or McCulloch branded 2-stroke engine oil. In either case use 2.5% (40:1) of oil. IMPORTANT Always shake this fuel mix vigorously each time you use it. We recommend to carry out this operation each time you use the fuel. Fuel mix properties deteriorate with time, we therefore recommend that you only make the quantity of fuel mix you will need for each usage. Do not use fuel mix more than a week old as this could damage the engine. UK WARNING Do not smoke when re-fuelling. Always open the fuel cap slowly. Re-fuel in open spaces only, keeping away from naked flames or sparks. Always store fuel in an approved container. SAFE STORAGE OF FUEL Petrol is highly inflammable. Put out all cigarettes, pipes and cigars before working with petrol. Avoid spilling petrol. Store fuel in a cool, well ventilated place, in an approved container specifically designed for the purpose. Never store engine with fuel in the tank in enclosed, poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light such as in a furnace, water heater, clothes dryer etc. Petrol fumes can cause an explosion or a fire. Do not store large amounts of fuel. CHAIN LUBRICATION IMPORTANT The service life of the bar and chain depends on good lubrication. Always use chain lubricating oil of medium viscosity. We recommend special McCulloch chain lubricating oil. Never use waste oil for this purpose. This results in damage to the bar, the chain and the oil pump. Refill the chain oil tank each time the saw is refuelled. IMPORTANT The chain oil feed is reduced to a minimum when the regulating bolt is completely closed (turning clockwise) To prevent possible restarting problems avoid running the fuel tank dry. This also helps to extend engine life. NOTE: Saw chain stretches during use particularly when it is new, and it will occasionally be necessary to adjust and tighten it. A new chain will require adjustment after about 5 minutes of operation. • The mechanical oil pump for chain lubrication can be adjusted. The feed rate of the chain oil pump can be adjusted by means of the regulating screw (A) (see details in the illustration). The oil feed rate is increased by turning the regulation bolt counterclockwise . IMPORTANT - The chain oil feed is reduced to a minimum when the regulating bolt is completely closed (turning clockwise). STARTING AND STOPPING E IMPORTANT. Never start or operate unless bar and chain are properly installed. Before starting always move the saw away from the fuelling area and place it on firm, flat surface, the guide bar to the front. STARTING COLD ENGINE Check that the chain brake is in the disengaged position moving the lever (L) backwards (towards the front handle). Move the stop/run lever (A) up to the cold start position (choke closed |–– • |) When in the cold start position, this lever also partially opens the throttle. Hold the saw firmly as shown in illustration and pull the starter rope until the engine fires once. Once you hear the engine start, or attempt to start, move the stop/run lever (A) to the intermediate position (choke open |–– •| | ). ATTENTION: The throttle remains partially open in this position and the chain may run. This allows the engine to warm up. Pull the starter rope until the engine starts. Allow engine to warm up for a few seconds, holding the saw firmly. Beware of moving chain. ATTENTION: Squeeze and then release the accelerator trigger (B). This will allow the throttle too close and the chain should no longer move. STOP To stop the engine, move the stop/run lever (A) down, to the “STOP” position. IMPORTANT. After lengthy use of the chain saw at full speed, we recommend to run the engine for a few seconds at idle speed before stopping it. STARTING A WARM ENGINE Leave the start/run lever (A) onto the run position (in the middle). Pull the starter handle until the engine runs. IMPORTANT: The automatic accelerator opening system will only function if the start/run lever (A) is moved up to the cold start position, and then back down to the run position (in the middle). Do this if the engine fails to run after starting. STARTING A WARM ENGINE AFTER FUELLING In the fuel tank as run completely dry, procede to start as with a cold engine. USAGE F IMPORTANT Before using a chain saw read the Operator’s Manual and all safety precautions carefully. FELLING TREES – Make sure that there are no bystanders or animals in the work area. – Study the direction of the fall of the tree and then plan your exit path away from the planned direction of fall. – Don’t fell trees when there is a strong wind. 1 Clear the tree base of interfering limbs and brush. Clean the work area from stones or other objects which could damage the chain. If the tree has large protruding roots, remove them before felling (see illustrations). 2 A) Cut a felling notch (A) of 45°on the side you want the tree to fall to a depth of about one third of the trunk diameter (d). Then make a felling cut (B) about 5 cm higher than the felling notch on the opposite side of the tree. Make sure that the felling cut does not go right through the trunk. A hinge (C) must always be left to provide control over the direction of the fall. 3 UK B) Use wedges to control the moment and direction of the fall. 3 When the tree starts to fall, walk away along your preplanned escape path. ROUTINE MAINTENANCE CUTTING FALLEN TRUNKS 4 A) Limbing thick branches. For limbing and bucking leave the lower limbs to support the log off the ground. B) Supported at one end only. Begin with a bottom cut made by the upper side of the bar (A); the depth of the cut should be about one third of the log diameter. Finnish with a top cut (B) meeting the first one. With this technique splitting, cracking can be avoided C) Supported at both ends. Begin with a top cut about one third of the log diameter. Then finish with a bottom cut (B) meeting the first one. this technique avoids the risk of pinching the bar in the log. D) If the log is supported along its whole length it may be cut normally from above. Take care not to touch the ground with the chain. • When working on a slope always stand on the uphill. • When cutting prepared timber, use clamps or chocks to secure work. • Use extreme caution when cutting small size brush and saplings which may catch the chain and pull you off balance. CHAIN: Check tension regularly. A new chain will require more frequent adjustment. Loosen retention nuts. Tighten chain (see assembly instructions). Tighten retention nuts and adjust. CARBURETTOR ADJUSTMENT G We suggest carburetor adjustments are made by an authorized servicing dealer. The carburetor has three adjustment screws: • L: The needle screw L governs the fuel flow at low speed and also the acceleration from low to full speed. To set screw L: close screw L turning it clockwise without forcing. Then open screw 1-1/4 full turn (counterclockwise) . If acceleration is not smooth, open another 1/8 turn to increase fuel flow . • H: The needle screw H governs fuel flow at high speed (throttle valve fully open). To set hi speed screw H: close screw H turning it clockwise without forcing . Then open screw 3/4-1 full turn (counterclockwise) . If the engine speed is too high, open the screw about 1/8 turn (counterclockwise). • I: The I (IDLE) screw controls the throttle opening to govern idle speed adjust as necessary. CAUTION: increased idle speed may cause chain movement. The carburetor is adjusted for normal operation during production. When considerable changes of altitude require a supplementary adjustment, contact an authorised service station which offers the latest in tools, parts and technical assistance. 4 H Ensure engine is always switched off before any kind of maintenance operation. 1 BAR – Clean the bar groove (K) and check the lubrication holes (L) in the bar to ensure that they are not clogged. – Grease sprocket periodically. Rotate sprocket and repeat. – Rotate bar periodically to maximise bar life. 2 AIR FILTER – A dust clogged air filter may cause carburetor problems. This may prevent the engine from reaching its maximum r.p.m. and cause high fuel consumption. – Remove cover. – Wash filter in petrol (do not use fuel which is mixed with oil). – The filter can also be cleaned with compressed air. – Replace filter if damaged or if it does not seal tightly in the air box. 3 SPARK PLUG Remove and clean the spark plug every 30 hours. Check the electrode gap (0,5/0,6 mm. - 0.025 inches). – Replace spark plug about every 100 working hours or whenever it is extremely encrusted. – Heavily encrusted electrodes can result from an incorrect carburetor setting or from wrong fuel mixture (too much oil in the fuel mix) or a poor quality of oil in the fuel mix. Check and correct. 4 OIL FILTER The oil filter is on the end of the oil suction hose inside the oil tank. Remove the chain catcher by twisting it anticlockwise and remove the oil filter. Use a piece of bent wire or long forceps. To remove deposits from the oil tank half-fill it with kerosene or petrol and shake thoroughly. Drain off and fill the tank with fresh saw chain oil. Never use waste oil. 5 FUEL FILTER To change fuel filter remove the tank cap and pull out the filter with a piece of bent wire or long forceps. Replace the filter as shown in the illustration and reposition it. It is recommended to replace the fuel filter at least once a year. CHAIN BRAKE – WARNING: Contact your service dealer if anything appears wrong with your chain brake. Do not disassemble or manipulate the mechanism of the chain brake. – Clean the brake mechanism periodically (without disassembling it) and control the wear of the band visually. • PERIODICALLY: It is important to clean the saw thoroughly particularly around cylinder fins to avoid overheating of the engine. • LONG STORAGE: Empty fuel and run engine until dry. UK SAFETY CHAIN BRAKE I Your chain saw is fitted with a safety chainbrake designed to stop the chain in milliseconds in case of kickback. Always hold the saw firmly in both hands. The chain brake does not provide a total protection if the machine is used without taking the necessary precautions and maintenances. The chain brake is intended to engage automatically in case of kickback. The chain brake can also be engaged manually by pushing the chain brake lever forwards.The manual use of the chain brake is recommended only at idle. Always test the chain brake before using your saw. Do this by engaging the brake at idle (see below). Always release the brake before starting. Kickback may occur if the end of the bar (see illustrated angle) touches any solid object. Never attempt to start a cut with the end of the bar. Kickback is a violent upward and rearward movement of the bar and may cause you to lose control of the machine. Therefore you should avoid starting a cut with this part of the bar. Always keep a firm grip on the saw with both hands because, in case of kickback, it is the contact of the left hand with the brake lever which will help to engage the brake. CHAIN BRAKE TESTING: 1 The chain brake (A) is disengaged when brake lever is pulled back and locked(chain can move). 2 The chain brake (A) is engaged when brake lever is in the position (chain cannot rotate).The chain brake should snap into both positions.If strong resistance is felt or lever does not move into either position, DO NOT USE YOUR SAW. Take it immediately to an authorized servicing dealer. 3 CHAIN CATCHER This unit is fitted with a chain catcher below the drive spocket. This is intended to stop the rearward movement of the chain in case of breakage or if it should come out of the bar. It should never be removed. CHAIN SHARPENING L 1 Chain cutter teeth can be sharpened with a round file, as follows: CHAIN FILE SPR 378 GX 7/32” The exact chain type is marked on the bottom half of the drive link which runs inside the bar groove. Filing can be made easier by also using a file holder. The chain can remain fitted on the bar during sharpening. Before commencing, the chain should be tensioned correctly and the chain brake should be activated to prevent the chain from moving. 2 To obtain a correct sharpening the file must be carefully held to maintain 3 basic angles: – “A” Top angle 30° - 35° – “B” External, side angle 85° - 90° – “C” Internal, side angle 60° File in one direction only, from the “inside” of the cutter tooth towards the “outside”. Do not allow the file to touch the chain as you bring it back to re-position it. Each cutter tooth should be filed with the same number of strokes. 3 The file should be held horizontally to the cutter tooth being sharpened. 4 Best results to obtain a precise sideways angle can be obtained by holding the file so that it rises 0,5 mm above the top face of the cutter tooth. 5 DEPTH GAUGE Correct depth gauge height is vital to ensure maximum chain life and cutting efficiency. The height of the depth gauge should be lowered as the cutter tooth is filed back; this height should be checked every 4 or 5 sharpenings. The best way to do this is to use a flat file and a depth gauge tool. The correct setting is 0.65 mm below the top edge of the cutter tooth. The cutter tooth depth gauge should then be rounded (D). FAULT FINDING TABLE Engine runs badly or looses power when cutting Check STOP switch is in the position I. Control fuel level min. 25% tank capacity. Check air filter is clean. Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. Control and adjust the carburetor screws if necessary. Change fuel filter. Contact your dealer. Carefully follow the cutting accessory assembly instructions. Check chain is sharp. Otherwise, contact your dealer. • • • • Engine will not start • • • • • The machine runs but does not cut well • • Engine still gives trouble: contact your dealer. 5 EC Declaration of Conformity GB DK The undersigned, authorised by E.O.P.I., declares that the petrol-driven chainsaw MS55, MS60, manufactured by E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, is in accordance with the European Directives 98/37/CEE (Machinery Directive), 73/23/EEC (Low Voltage Directive), 93/68/CEE (CE Marking Directive) & 89/336/CEE (Directive on electromagnetic compatibility). Directive 2000/14/ECC (Annex V). DE CE Konformitätserklärung ES Der Unterzeichnete, bevollmächtigt durch E.O.P.I., erklärt, daß die Kettensägen mit Benzinmotor MS55, MS60, hergestellt durch E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, den Europäischen Richtlinien 98/37/CEE (Maschinenrichtlinie), 73/23/EEC (Niederspannungsdirektive), 93/68/CEE (CE Kennzeichnungsrichtlinie) & 89/336/CEE (EMV Richtlinie) entspricht. Richtlinie 2000/14/ECC (Anhang V). FR Declaracion de cumplimiento de la directriz de la UE El abajo firmante, autorizado por E.O.P.I., afirma que las motosierras de gasolina MS55, MS60, fabricado por E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, cumple con las directivas Europeas 98/37/CEE (Directiva sobre Maquinaria), 73/23/EEC (Directiva sobre Bajo Voltaje), 93/68/CEE (Directiva sobre Marcas de la CE) & 89/336/CEE (Directiva sobre ‘Compatibilidad Electro Magnetica’). Directiva 2000/14/ECC (Anexo V). Déclaration de conformité Européenne Le soussigné, dûment mandaté par E.O.P.I., déclare que les tronçonneuses thermiques MS55, MS60, fabriqué par E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, est conforme aux Directives Européennes 98/37/CEE (Directive Sécurité Machine), 73/23/EEC (Directive Basse Tension), 93/68/CEE (Directive Marquage CE) & 89/336/CEE (Directive EMC). Directive 2000/14/ECC (Annexe V). NL PT IT EF Erklæring om Overensstemmelse Undertegnede, autorisert av E.O.P.I., erklærer at bensindrevne kjedesager MS55, MS60, produsert av E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, er i overensstemmelse med følgende europeiske direktiver: 98/37/CEE (Maskindirektiv), 73/23/EEC (Direktiv for lavspenning), 93/68/CEE (CE-merkingsdirektiv) & 89/336/CEE (Direktiv om elektromagnetisk kompatibilitet). Direktiv 2000/14/ECC (Annex V). FI ∆ήλωση Συµµ ρφωσης προς τις Eντολές της EE O υπογεγραµµένος, µε eξουσιοδτηση της E.O.P.I., δηλωνω τι: τα βενζινοκίνητα αλυσοπρίονα MS55, MS60, κατασκευασθέντα απ την E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, ανταποκρίνονται προς τις Eυρωπαϊκές Eντολές, 73/23/CEE Oδηγία χµηλής Tάσης (ασφάλεια), 98/37/CEE (η περί Mηχανηµάτων Eντολή), 93/68/CEE (η περί του Σήµατος CE Eντολή) & 89/336/CEE (η περί Hλεκτροµαγνητικής Συµβαττητας Eντολή). Kαvοvιδµς 2000/14/ECC (V). EU Julistus Vastaavuudesta HU Allekirjoittanut, E.O.P.I. in valtuttaamana, vakuuttaa että bensiinimoottorisahat MS55, MS60, ja jotka on valmistanut E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, on Euroopan direktiivien 98/37/CEE (Koneisto-direktiivi), 73/23/EEC (Matala jännite-direktiivi), 93/68/CEE (CE Merkintä-direktiivi) & 89/336/CEE (Elektromagneettinen Yhteensopivuus-direktiivi) mukainen. Direktiivi 2000/14/ECC (Liite V). SE Dichiarazione di Conformità CE Il sottoscritto, autorizzato dalla E.O.P.I., dichiara che la sega a catena portatile da legno MS55, MS60, costruito dalla E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italia, è conforme alle Direttive Europee: 98/37/CEE (Direttiva Macchine), 73/23/EEC (Direttiva Bassa Tensione), 93/68/CEE (Direttiva Marcatura CEE) & 89/336/CEE (Direttiva Compatibilità Elettromagnetica). Direttiva 2000/14/ECC (Allegato V). GR NO Declaração de Conformidade CE O abaixo assinado, autorizado por E.O.P.I., declara que as serras mecänícas a gasolina MS55, MS60, fabricada por E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, estão de acordo com as Directivas Europeias 98/37/CEE Directiva de Maquinaria), 73/23/EEC (Directiva sobre Baixas Tensões), 93/68/CEE (Directiva de Marcação CE) e 89/336/CEE (Directiva de Compatibilidade Electromagnética). Directiva 2000/14/ECC (Apêndice V). EG Conformiteitsverklaring Ondergetekende, gemachtigd door E.O.P.I., verklaart dat de benzine aangedreven kettingzaag MS55, MS60, geproduceerd door E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy voldoet aan de Europese Richtlijnen 98/37/CEE (Machinerie Richtlijn), 73/23/EEC (Matala jännite-direktiivi), 93/68/CEE (EG Markering Richtlijn) & 89/336/CEE (Richtlijn aangaande elektromagnetische compatibiliteit). Richtlijn 2000/14/ECC (Annex V). EU Overensstemmelse-erklæring Undertegnede, bemyndiget af E.O.P.I., erklærer herved, at benzindrevne kædesave MS55, MS60, E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, er i overensstemmelse med de eurpæiske direktiver 98/37/CEE (Maskineri direktiv), 73/23/EEC (Direktiv for lavspænding), 93/68/CEE (CE mærkningsdirektiv) & 89/336/CEE (EMC-direktiv). Direktiv 2000/14/ECC (Annex V). EC nyilatkozat Alulírott, a E.O.P.I. által meghatalmazott ezennel kijelenti, hogy a benzinmotoros láncfúrész MS55, MS60, amelyet a E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy gyárt, megfelelnek a 98/37/CEE európai irányelvnek (gépi berendezések irányelv), a 73/23/ EEC, a 93/68/CEE európai irányelvnek (CE-irányelv) és a 89/336/CEE (az elektromágneses kompatibilitásra vonatkozó irányelv). Direktíva 2000/14/ECC (Melléklet V). EC Declaration of Conformity Undertecknad, auktoriserad av E.O.P.I., försäkrar att bensindrivna kedjesågar MS55, MS60, tillverkade av E.O.P.I., 23868 Valmadrera (LC), Via Como 72, Italy, är i överensstämmelse med följande europeiska direktiv 98/37/CEE (Maskindirektiv), 73/23/EEC (Lågspänningsdirektiv), 93/68/CEE (CE-märknings-direktiv) & 89/336/CEE (Elektromagnetisk kompatibilitet). Direktiv 2000/14/ECC (Annex V). Electrolux Outdoor Products Via Como 72 23868 Valmadrera (Lecco) Valmadrera, 15.12.01 Pino Todero (Direttore Tecnico) E.O.P.I. Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and trademarks in several countries. © Electrolux Outdoor Products ITALIA Phone + 39 0341 203111 - Fax +39 0341 581671 The Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. PN. 247749 REV. 01 (11/02)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2003:04:07 17:18:11Z Modify Date : 2007:06:18 16:06:52+03:00 Subject : MOEN1999_530247749 Page Count : 13 Creation Date : 2003:04:07 17:18:11Z Producer : Apogee Series3 Pilot v1.0u1 Mod Date : 2007:06:18 16:06:52+03:00 Author : McCulloch Metadata Date : 2007:06:18 16:06:52+03:00 Title : OM, McCulloch, ProMac 54, ProMac 61, 95390009100, 95390009200, 1999-04, Chain Saw Creator : McCulloch Description : MOEN1999_530247749 Page Mode : UseThumbs Page Layout : SinglePageEXIF Metadata provided by EXIF.tools