Meade Ds Gen 1 Instruction Manual English Only 6 00

: Meade Meade-Ds-Gen-1-Instruction-Manual-719727 meade-ds-gen-1-instruction-manual-719727 meade pdf

Open the PDF directly: View PDF .
Page Count: 20

DS

P/N 14-0500-00 06/00

®

CONTENTS

Introduction ........................................................................................................................5

Unpacking ..........................................................................................................................5

Assembly: 60mm and 70mm models ................................................................................5

Assembly: 80mm, 90mm, 114mm, and 127mm Models ....................................................7

Balancing the Tube in the Mount........................................................................................7

Attaching the Viewfinder ....................................................................................................7

Focusing the Viewfinder ................................................................................................9

Aligning the Viewfinder ..................................................................................................9

Observing Through the Telescope......................................................................................9

The Focuser and the Eyepiece-Holder ........................................................................10

Astronomical Observing................................................................................................10

Eyepieces and Magnification........................................................................................10

The Barlow Lens ..........................................................................................................10

A Note About Power......................................................................................................11

Collimation of the Telescope's Optical System ................................................................11

Maintenance......................................................................................................................11

Questions and Repairs ................................................................................................11

Appendix 1: Optical Alignment of 114mm and 127mm Models: ......................................13

Appendix 2: Telescope Control Systems ..........................................................................15

#490 Manual Slow-Motion Control set ........................................................................15

#492 Dual-Motor Electronic Control System................................................................15

To Install the #492 System ..........................................................................................15

Operating Notes on the #492 Dual-Motor Electronic Control System ........................17

#493 Autostar Computer Control System ....................................................................18

To Install the #493 System ..........................................................................................18

Appendix 3: Optional Electronic and Computer Drive Systems ......................................19

#490 Manual Control Set..............................................................................................19

#492 Dual-Motor Electronic Control System................................................................19

#493 Autostar Computer Control System ....................................................................19

#495 Autostar Handbox................................................................................................19

#497 Autostar Handbox................................................................................................19

- 3 -

® The name “Meade,” the Meade logo, and “Autostar” are trademarks registered with the U.S. Patent Office and in

principal countries throughout the world. All rights reserved.

© 2000 Meade Instruments Corporation.

- 4 -

1

2

3

4

5

6

11

7

19

821

9

18

20

10

12

13

13

13

14

16

17

15

A

Introduction: Meade Digital Electronic Telescope Series (DS) models are illustrated in the fol-

lowing figures: Fig. A — 60mm and 70mm refracting telescopes; Fig. B — 80mm and 90mm

refracting telescopes; Fig. C — 114mm and 127mm reflecting telescopes. Telescope optical

specifications (diameter, D, and focal length, F) are printed on a foil plate affixed to the opti-

cal tube. Example: 60mm models have a diameter D = 60mm and a focal length F = 700mm.

Meade DS instruments are available in a variety of trade names (Polaris, Saturn, TeleStar,

etc.), with different levels and types of accessorization. All of these telescopes, however,

share the same basic optical tube assemblies, mechanical mountings, tripods, and other fea-

tures. The instructions provided here apply equally well to all DS trade names.

All Meade DS telescopes are similar in assembly and operation. Fig. A is used in these

instructions for most references where assembly or operation is identical among all the

models. Differences among the models, where these differences affect assembly or opera-

tion, are pointed out below.

Users of DS models which include (either as part of the original telescope or purchased sep-

arately as an optional feature) an additional telescope control system (such as the #490

Manual Slow-Motion Control Set, the #492 Dual-Motor Electronic Control System, or the #493

Autostar Computer Control System) should first assemble the basic telescope; instructions for

adding one of these optional control systems are given in Appendix 2 of this manual.

Unpacking: Locate and remove the following components and parts from the packing box:

optical tube (A-1); viewfinder (A-4) and viewfinder bracket (A-5); yoke mount (A-6); tripod legs

(A-7); poly bag with 3 bolts and nuts for attaching the tripod to the yoke (60mm and 70mm

models only); accessory shelf (A-8); one or more eyepieces (A-9); diagonal mirror (A-10, not

included with 114mm and 127mm models). On 60mm and 70mm models the optical tube is

factory-attached to the yoke mount and the tripod legs are packed separately in the packing

box. On all other models the yoke mount is factory-attached to the three tripod legs and the

optical tube is packed separately in the packing box.

Assembly: 60mm and 70mm Models — Attach the three (aluminum) tripod legs to the base

of the yoke mount, as shown in Fig. A. In attaching each leg, slide one of the bolts through

the hole (A-12) at the top of the leg, thread the hex nut on to the opposite end of the bolt, and

- 5 -

WARNING! Never use a Meade®DS

Telescope to look at the Sun! Looking at or

near the Sun will cause instant and irre-

versible damage to your eye. Eye damage is

often painless, so there is no warning to the

observer that damage has occurred until it is

too late. Do not point the telescope or its

viewfinder at or near the sun. Do not look

through the telescope or its viewfinder as it is

moving. Children should always have adult

supervision while observing.

CAUTION: Use care to install batteries

as indicated by the battery compart-

ment. Follow battery manufacturers'

precautions. Do not install batteries

backward or mix new and used batter-

ies. Do not mix battery types. If these

precautions are not followed, batteries

may explode, catch fire, or leak.

Improperly installed batteries void your

Meade warranty.

Assembly and Operating Instructions for

Meade®Digital Electronic Telescope Series

60mm (2.4"), 70mm (2.8"), 80mm (3.1"), 90mm (3.5") Refracting Telescopes; 114mm

(4.5"), and 127mm (5") Reflecting Telescopes

Numbered references are to the figures on the pages of this manual. Example: “D-4” refers to

item 4 of Fig. D.

- 6 -

B

1

5

2

7

8

9

9

9

3

4

6

1

3

4

5

6

7

2

5

6

7

1

2

3

4

8

11

9

10

10

10

C

D

1

2

3

4

5

5

E

use a “+” (Phillips-head) screwdriver to tighten the bolt to a “firm feel.” Do not overtighten. Note

that each tripod leg includes a flip-lock (A-13) for adjusting the overall length of the tripod.

These flip-locks should all face inward as the legs are attached to the yoke mount.

With the tripod legs attached to the yoke mount and sitting on a flat surface, spread the legs

out gently until all legs are fully spread out. Attach the accessory shelf (A-8) to one of the tri-

pod legs by placing one of the shelf’s flanges (A-20) at one edge of a tripod leg and then

pulling the shelf around the leg until the other shelf flange snaps into place. (To remove the

accessory shelf, push one of the flanges with both thumbs from the outside surface of the tri-

pod leg.) The accessory shelf can be pushed up or down the tripod leg to a convenient height.

The telescope should now appear as in Fig. A, except that the viewfinder (A-4) has not yet

been attached.

Note: Assembly of 60mm and 70mm models supplied with hardwood tripods is similar to the

assembly described above. Each tripod leg attaches with one of the supplied bolts (D-5)

through holes at the top of the leg; a washer and wing nut (D-6) fasten each leg to the base

of the yoke mount (D-7). The metal flange (D-1) of each wood tripod leg should face inward.

Attach the metal, triangle-shaped accessory shelf (D-2) to each of the three tripod legs using

the thumbscrews (D-3) and wing nuts provided. To adjust tripod height, slide the inner section

of each tripod leg up or down, securing it in position with firm-feel tightening (do not over-

tighten) of the thumbscrew (D-4).

Assembly: 80mm, 90mm, 114mm, and 127mm Models — Place the tripod (with yoke mount

attached) on a flat surface and gently spread the three tripod legs outward until they are fully

spread out. Each of these models includes a cradle ring system (B-1 or C-1), permitting the

optical tube to be moved upward or downward within the cradle rings for proper balancing of

the tube on the yoke mount. As the yoke mount/tripod assembly is removed from the pack-

ing box, only the lower-half (E-1) of each cradle ring is present. Locate the upper half (E-4)

of each cradle ring in the packing box and connect each upper-half ring to its respective lower-

half ring by inserting the flange (E-2) of each upper-half ring into the slot (E-3) located at the

top of the lower-half ring. Be certain that each flange (E-2) is firmly seated into the corre-

sponding slot. Each upper-half ring should now close down to form a complete circular ring

without undue pressure being required. Open the upper-half rings and place the optical tube

into the cradle rings. See Fig. F. Close the rings and tighten (to a firm-feel only) the latches

(E-5). The telescope should now appear as in Figs. B or C, except that the viewfinder (B-6)

or (C-6) has not yet been attached. The flip-lock (B-9 or C-10) on each tripod leg permits

adjustment of tripod height.

Balancing the Tube in the Mount (80mm, 90mm, 114mm, and 127mm models only): Loosen

slightly (by rotating half a turn counterclockwise) the vertical lock (B-2 or C-2). Placing your hand

on the upper end of the optical tube, move the tube up and down in a vertical direction within the

U-shape yoke mount (B-4 or C-4). The tube should move easily and be well-balanced about the

vertical axis of motion; if not, slightly loosen the cradle ring latches (E-5), move the optical tube

up-or-down within the cradle rings to achieve good balance, and re-tighten the latches (E-5).

Attaching the Viewfinder: Because the main telescope has a fairly narrow field of view,

locating objects directly in the main telescope can sometimes be difficult. The viewfinder (A-

4) is a small, wide-field telescope with crosshairs that permits easy object location. With the

viewfinder and main telescope aligned to each other, so that both point to the same position

in the sky, the observer first locates an object in the viewfinder; the object is then also posi-

tioned within the field of the main telescope.

The viewfinder bracket (A-5) attaches to the focuser housing at the position shown in Figs. A,

B, or C. (On 114mm and 127mm models the viewfinder bracket attaches to the mounting

block (C-7) located on the main telescope tube, near the focuser.) Using a “+” (Phillips-head)

- 7 -

- 8 -

1

2

3

F

1

2 8

7

4

5

6

3

33

]

30mm

(1.2")

24mm

(0.94")

148mm

(5.8")

176mm

(6.9")

6 x 30mm

5 x 24mm 1

32

G

H

J

K

screwdriver, secure the bracket in position by tightening the two attachment screws (G-1)

inside the bracket (these screws are placed inside the bracket at the factory) into the mating

threads (G-6) located on the focuser housing, or (in the cases of 114mm and 127mm models)

located on the mounting block (C-7).

Slide the viewfinder (G-2), eyepiece-end (G-8) first, into the viewfinder bracket. (Remove the

rubber eyecup (G-8) from the viewfinder before sliding the viewfinder into the bracket.

Replace this rubber eyecup after the viewfinder is positioned in the bracket.) Tighten (to a

firm-feel only) the four alignment thumbscrews (G-3) to hold the viewfinder in the bracket.

Focusing the Viewfinder: Each Meade DS telescope is supplied with one of two viewfinder

models, 5 x 24mm or a larger 6 x 30mm. Identify the viewfinder of your telescope from Fig.

H. Focusing the 5 x 24mm viewfinder is accomplished by turning the viewfinder eyepiece (H-

1) on its internal thread. Generally a few turns are sufficient to achieve proper focus. The 6 x

30mm viewfinder is locked into permanent focus at infinity. Look through the 6 x 30mm

viewfinder at a distant land object; if the focus is not sharp, then follow this procedure: (a)

loosen the focus lock ring (H-2) a few turns, permitting the lens cell (H-3) to be rotated; (b) look-

ing through the viewfinder at a distant land object, rotate the lens cell until the object is sharply

focused; (c) tighten the focus lock ring (H-2) up against the lens cell.

Important Note: Objects appear upside-down and reversed left-for-right when observed in the

viewfinder. With refracting telescope Models DS-60, DS-70, DS-80, and DS-90, objects

viewed through the main telescope with the diagonal mirror (A-10) in place are seen right-side-

up, but reversed left-for-right. This image inversion is of no consequence when observing

astronomical objects, and in fact all astronomical telescopes yield inverted images. During ter-

restrial observing, where a fully-correctly-oriented image (right-side up and correct left-for-right)

is desirable, an optional Meade 45° Erecting Prism (available in either 0.965" or 1.25" format

to suit the appropriate Meade telescope model) is available. See the optional accessories

sheet which accompanies the telescope or consult the Meade Telescope Catalog. Note that for

reflecting telescopes, including Meade Models DS-114 and DS-127, no means of image inver-

sion is available; while these telescopes may be used for terrestrial observing, the image will

not be correctly oriented in either right-side-up or left-for-right orientations.

Aligning the Viewfinder: Loosen the vertical (A-14) and horizontal (A-15) locks, by turning

the lock knobs about one turn counterclockwise, permitting the telescope to move freely on

both axes. Place a low-power (e.g., 25mm) eyepiece in the focuser of the main telescope and

point the telescope at an easy-to-find land object (e.g., the top of a telephone pole). Turn the

focuser knob (A-16) so that the image is sharply focused, and center the object precisely in

the main telescope’s field of view. Re-tighten the lock-knobs (A-14) and (A-15). Then, looking

through the viewfinder, turn the viewfinder’s four alignment screws (G-3) until the viewfinder’s

crosshairs point precisely at the same object as centered in the main telescope. The viewfind-

er is now aligned to the main telescope. The right-hand image in Fig. J shows an object cen-

tered in the main telescope before the viewfinder (the left-hand image) has been aligned to

the main telescope. Fig. K shows these same images after the viewfinder and main telescope

are aligned.

Assembly of the basic telescope is now complete. If your telescope includes one of the DS

optional features, continue to Appendix 2 to complete the assembly of the optional feature

before observing.

Observing Through the Telescope: Place the diagonal mirror (A-10) in the telescope’s eye-

piece-holder (A-17) and tighten the thumbscrews of the eyepiece-holder to secure the diago-

nal mirror in place. (Note that DS 114mm and 127mm reflecting telescope models do not

include, and do not require, a diagonal mirror.) Place a low-power (e.g., 25mm) eyepiece into

the diagonal mirror (or, with DS 114mm and 127mm models, directly into the eyepiece-hold-

er), and tighten the eyepiece in place with the thumbscrews (A-18) provided.

- 9 -

The diagonal mirror permits a comfortable 90°angle for observing sky objects with DS 60mm

through 90mm refracting telescopes; in addition the diagonal mirror results in an upright, but

reversed left-for-right, image through the telescope during terrestrial observations. Loosen the

vertical (A-14) and horizontal (A-15) locks, by turning the lock knobs about one turn counter-

clockwise. The telescope’s main tube now moves easily in either vertical or horizontal direc-

tions. Alternately, “partially-locking” these locks provides a comfortable “drag”, neither too

loose nor too tight, in the motion of the telescope tube about the vertical and horizontal axes.

Experiment to find the best lock-knob tensions.

Begin by observing easy-to-find land objects. Obtain a sharp image by turning the focuser

knob (A-16). Use the viewfinder to locate objects before observing them in the main tele-

scope. Start the observation of any object, astronomical or terrestrial, with a low-power eye-

piece (see Eyepieces and Magnification, below), stepping up to higher power eyepieces, if

desired, after the image is centered and focused in the main telescope.

The Focuser and Eyepiece-Holder: Depending on the telescope model, Meade DS tele-

scopes are supplied with an eyepiece-holder (G-4) that accepts eyepieces of either .965"

(24.5mm) or 1.25" (31.7mm) barrel-diameter. DS models of 70mm and larger also include a

separate eyepiece-holder that accepts giant, wide-field eyepieces of 2" (50.8mm) barrel-diam-

eter, such as the optional Meade MH50mm eyepiece. This 2" eyepiece-holder ring threads on

to the end of the focuser drawtube and replaces the standard eyepiece-holder (G-4) when 2"

eyepieces are employed. The focuser drawtube lock (G-5) helps to prevent focuser slippage

when heavier accessories are added to the eyepiece end of the telescope.

Astronomical Observing: With the telescope focused on a celestial object such as the

Moon, a planet, or a deep-space galaxy or nebula, the object is seen to move quite rapidly

through the telescopic field of view. This apparent motion is caused by the Earth’s rotation on

its axis once every 24 hours. To follow, or “track,” the object, place a hand on the main tele-

scope tube and move the telescope on one or both of its vertical and horizontal axes. Tracking

astronomical objects, particularly at higher powers, is greatly facilitated with the addition of a

manual or electronic telescope control system. See Appendix 2.

Eyepieces and Magnification: The magnification, or power, of a telescope is determined by

two factors: the focal length, F, of the main telescope (this focal length is printed on a label

affixed to the telescope tube or focuser), and the focal length of the eyepiece employed. Each

Meade telescope is supplied with one or more eyepieces; some models also include a Barlow

lens, described below, which doubles or triples eyepiece power. To calculate the power at

which the telescope is operating, use this formula:

Focal Length of Main Telescope

__________________________

Power = Focal Length of Eyepiece

Example: Meade 60mm DS telescopes have a focal length of 700mm. The power obtained

with a 25mm eyepiece is calculated as:

700mm

_______

Power = 25mm = 28 times (written as “28X”)

The optical type of an eyepiece (e.g., SR, H, MA, MH, etc.) has no bearing on power, but does

affect such characteristics as field of view and image corrections.

The Barlow Lens: Some Meade telescopes include a power multiplier called a Barlow lens.

Consisting of a lens mounted in a 4" (10cm)-long tube, the Barlow doubles or triples the power

- 10 -

obtained when an eyepiece is used alone. In the example above a 25mm eyepiece results in

28X magnification with the Meade 60mm DS telescope; when this same eyepiece is used in

conjunction with a 2x Barlow lens, power is doubled to 56X. To use the Barlow, insert it into

the telescope’s focuser/eyepiece-holder (A-17), followed by the diagonal mirror and an eye-

piece. (With Meade 114mm and 127mm DS telescopes, insert the Barlow into the telescope’s

focuser/eyepiece-holder, followed directly by an eyepiece.)

A Note About Power: The most common mistake of the beginning observer is to use pow-

ers which the telescope’s aperture (diameter) and typical atmospheric conditions cannot rea-

sonably support. The result is an image which is fuzzy, ill-defined, and poorly resolved,

through no fault of the telescope. Keep in mind that a smaller, lower-power but brighter and

well-resolved image is far superior to a large, high-power, but dim and poorly-resolved one.

Most commonly, Meade DS telescopes are best used at powers from about 30X (for land

observing and for extended astronomical objects such as diffuse nebulae and star clusters) to

about 150X (for more detailed study of the Moon and planets). Use higher powers only when

the air is steady and when such powers actually increase the level of visible detail.

Collimation of the Telescope’s Optical System: The optical systems of Meade 60mm

through 90mm refractors are collimated (aligned) at the factory and never require adjustment.

Similarly, it is unlikely that the user of a Meade DS 114mm or 127mm reflecting telescope will

need to adjust the factory-aligned optics of either of these models. Users of 114mm and

127mm models should, however, read Appendix 1 to confirm this point.

Maintenance: The objective lenses of Meade DS 60mm through 90mm refracting telescopes

and the primary and secondary mirrors of DS 114mm and 127mm reflecting telescopes should

be cleaned as infrequently as possible. A little dust on a lens or mirror causes negligible loss

of image quality and should not be considered as reason to clean it. If the telescope’s dust

cover (A-3) is replaced after each observing session, cleaning the optics will rarely be

required. When cleaning a lens or mirror does become necessary, use a camel’s hair brush

or compressed air gently to remove dust. The dew shield (A-19) of 60mm through 90mm

refracting telescopes should be removed to access the lens prior to cleaning.

Questions and Repairs: In the U.S.A. questions concerning any Meade DS telescope,

accessories, or optional systems should be directed to: Customer Service Dept., Meade

Instruments Corp., 6001 Oak Canyon, Irvine, California 92618; FAX: (949) 451-1460;

Telephone: (949) 451-1450. Do not return a telescope or telescope part to Meade

Instruments before calling or writing us first; the great majority of repair situations can be

handled without requiring return of the telescope to us. Outside the U.S.A. please contact the

Meade international distributor in your country. A listing of Meade international distributors is

included in the Meade website www.meade.com.

- 11 -

3

6

25

1

4

L

- 12 -

2

1

3

3

2

1

2

3

4

5

M

N

P

1

2

1

2

3

Q

R

2

1

2

3

4

S

Appendix 1: Optical Alignment of 114mm and 127mm Models

Meade DS 60mm, 70mm, 80mm, and 90mm refracting telescopes are optically aligned (colli-

mated) at the factory prior to shipment, and it is never necessary to re-collimate the optics of

these models. Meade DS 114mm and 127mm reflecting telescope models are also factory-

aligned, but may occasionally require re-alignment, particularly if the telescope has received

rough handling in shipment. Before using one of these models for the first time, check the

alignment of the optics as outlined in this appendix. Good optical alignment is essential for

telescope performance, and in any case the alignment procedure is not difficult to follow.

Refer to Figs. L through S:

The optical systems of Meade DS reflecting telescopes include the following parts: primary mir-

ror (L-1); secondary mirror (L-2); secondary mirror-holder (L-3); secondary mirror-vanes (L-4

and M1); primary mirror-tilt screws (L-5). The telescope’s image is brought to a focus at (L-6).

1. Confirm alignment: To confirm optical alignment look down the focuser drawtube (C-11 and

P-1) with the eyepiece removed. The edge of the focuser drawtube frames reflections of the

primary mirror (P-2), the secondary mirror (P-3), the three (“spider”) vanes (P-4) holding the

secondary mirror, and the observer’s eye (P-5). With the optics properly aligned, all of these

reflections appear concentric (centered), as shown in Fig. P. Any deviation from concentrici-

ty of any of these telescope parts with the eye requires adjustments to the secondary mirror-

holder (Fig. M) and/or the primary mirror cell (Fig. N), as described below.

2. Secondary mirror-vane adjustments: If the secondary mirror (Q-1) is left or right of center

within the drawtube (Q-2), slightly loosen the 3-vane adjustment/lock knobs (M-1) located on

the outside surface of the main tube and slide the entire secondary mirror-holder system up or

down in the slotted holes of the main tube until the secondary mirror is centered in the draw-

tube. If the secondary mirror (Q-1) is above- or below-center within the drawtube, thread

inward one of the adjustment/lock knobs (M-1) while unthreading another of these knobs. Only

make adjustments to two knobs at a time until the secondary mirror appears as in Fig. R.

3. Secondary mirror-holder adjustments: If the secondary mirror (R-1) is centered in the

focuser drawtube (R-2), but the primary mirror is only partially visible in the reflection (R-3),

the three “+” (Phillips head) secondary mirror-tilt screws (M-2) should be slightly unthreaded

to the point where the secondary mirror-holder (M-3) can rotate about its axis parallel to the

main tube. Grasp the secondary mirror-holder (avoid touching the mirror surface!) with your

hand and rotate it until, looking through the drawtube, you can see the primary mirror centered

as well as possible in the reflection of the secondary mirror. With the rotation of the second-

ary mirror-holder at this best-possible position, thread in the three Phillips-head screws (M-2)

to lock the rotational position. Then, if necessary, make adjustments to these three Phillips-

head screws to refine the tilt-angle of the secondary mirror, until the entire primary mirror can

be seen centered within the secondary mirror’s reflection. With the secondary mirror thus

aligned the image through the drawtube appears as in Fig. S.

4. Primary mirror adjustments: If the secondary mirror (S-1) and the reflection of the primary

mirror (S-2) appear centered within the drawtube (S-3), but the reflection of your eye and the

reflection of the secondary mirror (S-4) appear off-center, then the primary mirror-tilt requires

adjusting, using the Phillips-head screws of the primary mirror cell (N-3). These primary mir-

ror-tilt screws are located behind the primary mirror, at the lower end of the main tube. See

Fig. N. Before adjusting the primary mirror-tilt screws, first unscrew by several turns (use

either a hex wrench or pliers) the three hex-head primary mirror lock screws (N-2) which are

also located on the rear surface of the primary mirror cell and which alternate around the cell’s

circumference with the three Phillips-head screws. Then by trial and error turn the primary mir-

ror Phillips-head tilt screws (N-3) until you develop a feel for which way to turn each screw to

center the reflection of your eye in the drawtube. (An assistant is helpful in this operation.)

With your eye centered as shown in Fig. P, turn the three hex head primary mirror lock screws

(N-2) to re-lock the tilt-angle of the primary mirror.

The telescope’s optical system is now aligned, or collimated. This collimation should be re-

checked from time to time, with small adjustments (per steps 1, 2, and/or 3, above) effected

as required to keep the optics well-aligned.

- 13 -

- 14 -

2

1

T

1

2

U

Appendix 2: Telescope Control Systems

Depending on the Meade DS telescope model, one of the following manual or electronic con-

trol systems may be included in the telescope’s standard specifications. (Telescope specifi-

cations are generally listed on the box in which the telescope is packed.) Alternately, any of

these control systems may be purchased separately as an optional feature.

#490 Manual Slow-Motion Control Set: The #490 Control Set permits manual tracking of

astronomical and terrestrial objects through the telescope, by turning one or both of the man-

ual control knobs; one slow-motion control is attached to each of the vertical and horizontal

axes of the telescope, as shown in Figs. T and U.

If purchased as an option, the instructions for mounting the #490 are included with the control

set itself. If this feature is standard on your telescope, the control set is preassembled on the

telescope, except the control knobs (T-1 and T-2). Attach these knobs with the provided hex

key. Be sure to align the set screw with the flat on the shaft.

With the lock-knobs (U-1) and (U-2) in their locked positions, the observer may track, or fol-

low, any object, astronomical or terrestrial, by turning one or both of the control knobs (T-1)

and (T-2). To move the telescope rapidly from one point in the sky to another, unlock the lock-

knobs (U-1) and (U-2), relocking them once the desired object has been placed in the tele-

scopic field.

Note that placing each of the two lock-knobs in a “partially-locked” position creates a com-

fortable drag in moving the telescope. Experiment with the lock-knobs to find the optimum lock

tensions for your applications.

#492 Dual-Motor Electronic Control System: With the #492 Electronic Control System

attached to any Meade DS telescope, all motions of the telescope, including moving the tele-

scope to an object, centering it in the field of view, and tracking it (in the case of an astro-

nomical object) to compensate for the Earth’s rotation, may be effected through the pushbut-

ton Electronic Controller (Fig. X).

If purchased as an option, the instructions for mounting the #492 are included with the control

system itself. If this feature is standard on your telescope, the user needs to attach the motor

assemblies to the telescope, as described below.

The #492 System consists of the following components, each of which should be located in

the packing before installation to the telescope is attempted (see Figs. V and Y): battery pack

(Y-1); accepts ten AA-size user-supplied batteries) with cord; two small hex wrenches; two

(identical and interchangeable) motor assemblies (V-1) and (V-4) with cords; one Electronic

Controller handbox (Fig. X). (Note that for clarity cords attached to the motor assemblies and

battery pack are not shown in the accompanying Figs. V and Yof the #492 Control System.)

To install the #492 System:

1. Place ten AA-size batteries inside the battery pack (Y-1), with correct battery orientation as

indicated on the battery pack’s internal holder; attach the battery pack to one of the tripod legs

using the Velcro fastener as shown in Fig. Y, or set it on the accessory shelf (Fig. Y).

2. Attach the vertical motor assembly (V-1) to the vertical control unit by placing the knurled

ring (V-2) of the motor assembly over the reduction gear (V-3). Note that three small plastic

tabs project outward about 3mm (1/8") from the face of the threaded ring near the reduction

gear (V-3). These “locator” tabs must fit into mating slots located just-inside the knurled ring

(V-2). Wiggle the motor assembly (V-1) to engage the reduction gear (V-3) with the internal

gears of the motor assembly (V-1). The knurled ring (V-2) locks into position by threading it

to a mating thread located on the vertical control unit. Turn the knurled ring to a firm-feel only;

do not overtighten.

- 15 -

- 16 -

1

2

3

4

5

V

MEADE

SPEED

IN

FOCUS

OUT

MODE

5

1

2

3

4

6

X

COMPUTER CONTROL

HBX

12v

AZ ALT AUX

W

MEADE

SPEED

IN

FOCUS

OUT

MODE

1

3

2

Y

6

7

- 17 -

3. Attach the horizontal motor assembly (V-4) to the telescope by following the same proce-

dure outlined in step 2, above.

Note: With both the vertical and horizontal motor assemblies attached, the telescope now

appears as in Fig. Y. (Note that cords have been omitted from Fig. Y for clarity.)

4.

Plug in the following cords to the control panel (V-5 and Fig. W):

a. Cord from the vertical motor assembly (V-1) plugs into the ALT (altitude, or vertical) jack

(Fig. W).

b. Cord from the horizontal motor assembly (V-4) plugs into the AZ (azimuth, or horizon-

tal) jack (Fig. W).

c. Cord from the Electronic Controller (Y-2) plugs into the HBX (handbox) jack (Fig. W).

5. Finally, plug the cord from the battery pack (Y-1) into the “12v” jack (Fig. W).

6. As soon as the battery pack is connected to the “12v” jack on the control panel, all four indi-

cator lights on the Electronic Controller (Fig. X) start blinking rapidly. Press the SPEED key

on the Electronic Controller and the telescope slews (moves) momentarily in the vertical and

horizontal directions to test the motors. When the test is complete, Light 1 (see Fig. X) comes

on steady; Lights 2, 3, and 4 turn off.

7. The #492 Dual-Axis Electronic Control System is now operational. Use the four arrow keys

(X-5) to slew the telescope to the desired object. To change speeds, press the SPEED key (X-

6) on the Electronic Controller. Depressing this key consecutively causes telescope speed to

cycle through all of the four available speeds, from fast to very slow.

The speed in operation is indicated by the four indicator lights (1, 2, 3, and 4, Fig. X) on the

Electronic Controller, as follows:

Light 1: 5°/second (fast). Use this speed to move the telescope across the sky rapidly

from one object to another.

Light 2: 0.75°/second (moderate). Use to center objects in the field of the viewfinder.

Light 3: 8 arc-minutes/per second (slow). Use to center objects in the field of view or to

track objects at lower powers.

Light 4: 2 arc-minutes/sec. (very slow). Use to center objects in the field of view or to

track objects at higher powers (e.g., above magnifications of about 80X).

Operating Notes on the #492 Dual-Motor Electronic Control System:

1. For the motors of the #492 System to be operational, the vertical and horizontal lock-knobs

(V-6) and (V-7) must be in their locked positions. Firm-feel tightening of these locks is suffi-

cient. Do not overtighten.

2. When setting up the telescope, always plug in the battery pack to the control panel last,

after plugging in the two motors and the Electronic Controller. Connecting the battery pack to

the control panel before the motors and Electronic Controller are connected may result in false

electrical signals being sent to the motors, causing them to malfunction. In this case unplug

the battery pack from the control panel, wait a few seconds, and plug the battery pack back

into the control panel. This operation clears the motors of any false signals.

3. When using the arrow keys (X-5) to reverse the direction of motion of the telescope (e.g.,

when changing the telescope's direction of motion from horizontal-right to horizontal-left),

there may be a brief pause before the telescope begins moving. This pause is caused by the

internal gears of the motor assemblies.

4. The MODE key of the Electronic Controller (Fig. X) is inoperative on the #492 System;

pressing this key has no effect. (The MODE key is used in certain specialized operations on

other Meade telescope models where equatorial (polar) alignment of the telescope is desired.)

5. The IN and OUT keys are used in conjunction with the optional Meade #1240 Electric

Focuser. With the #1240 unit attached to the telescope’s focuser, precise focusing of the tel-

escopic image may be accomplished directly from the Electronic Controller. Detailed instruc-

tions are included with the #1240 Electric Focuser.

6. Note that the telescope’s accessory shelf (A-8) includes a holder (A-21) for the Electronic

Controller.

7. When using the #492 System, take care that cords do not become wrapped around the tel-

escope; keep the cords “loose” at all times. Do not allow the telescope to slew into the tripod

or other fixed object. Do not touch or hold the telescope tube while it is moving.

8. If the motors stall or do not have sufficient power to move the telescope, place fresh bat-

teries in the battery pack. Long-life alkaline batteries are recommended.

#493 Autostar Computer Control System: Attached to any Meade DS telescope, the #493

Autostar Computer Control System permits fully automatic motorized location (at 5°/second on

both telescope axes) of more than 1400 celestial objects, including the major planets from

Mercury to Pluto; all 110 deep-space Messier objects; the finest galaxies, diffuse nebulae, plan-

etary nebulae, and star clusters from the New General Catalog (NGC), the Index Catalog (IC),

and the Caldwell catalog; hundreds of stars (double stars, variable stars, SAO stars); 15 peri-

odic comets; 50 earth-orbiting satellites; and more. In addition the Autostar System can per-

form an automatic GO TO function to any object of known celestial coordinates (Right

Ascension and Declination). Enter any of the preceding objects into the Autostar display, press

GO TO, and the telescope moves to the object and places it in the telescopic field of view.

To install the #493 system:

Installation of the #493 system is identical to the procedure described in "To Install the #492

System," page 15, except for step 4c. In this step, the cord from the #493 Autostar Computer

Control System plugs into the HBX (handbox) jack (Fig. W).

Instructions for the operation of the #493 Autostar Computer Control System are included with

the System itself.

Important Note: The first time Autostar initializes, it calibrates the motors. If you remove the

motors after a viewing session, mark one of the motors so that you remember the orientation

of the motors. Use the same orientation in subsequent observing sessions; otherwise Autostar

detects what appears to be a motor failure. If this occurs and a motor failure message is dis-

played, the motors have to be recalibrated.

- 18 -

Appendix 3: Optional Electronic and Computer Drive Systems Available

for Your Meade Digital Electronic Series Telescope

Your Meade DS telescope can be equipped with the latest in high-technology electronic drive

systems. These systems attach to Meade DS telescopes in minutes and greatly extend the

usefulness and excitement of telescope operation.

#490 Manual Slow-Motion Control Set

Use the Manual Slow Motion Control Set to manually track astronomical and terrestrial objects

through the telescope by turning one or both of the manual control knobs attached to the ver-

tical and horizontal axes of the telescope. Allows manual micrometric slow-motions of the tel-

escope.

#492 Dual-Motor Electronic Control System

Use the Electronic Control System for pushbutton motions of the telescope on both telescope

axes, simultaneously, at any of the drive speeds; very slow, slow, moderate, and fast. Track

astronomical and terrestrial objects at the push of a button. The #492 system operates from a

small battery pack included with the system, that accepts ten AA-size (user supplied) batteries.

#493 Autostar Computer Control System

With the Meade Autostar system attached to your telescope, fully automatic astronomical

object-location becomes a reality. Bring up the object you want to observe from Autostar’s

1400-object database on to the Autostar display, press GO TO, and the telescope automati-

cally moves to the object and places it in the telescope field of view! In addition, Autostar

enables the telescope to track the object automatically, fully compensating for the earth’s rota-

tion. Objects seem to “stand still” as the telescope follows their motions across the sky.

Supplied with 2 control motors, battery pack and Autostar #495 handbox.

#495 Autostar Handbox

Owners of DS telescopes already equipped with the #492 EC System (see above) need only

purchase the #495 handbox to convert their telescopes to full Autostar operation. See the

description of the #493 Autostar System above for more details.

#497 Autostar Handbox

Includes all the features of the #495 handbox, but offers a database of over 14,000 objects,

including over 5,000 objects from the Index Catalog (IC), 7800 objects from the New General

Catalog (NGC), 109 objects from the Caldwell catalog and over 900 stars from the

Smithsonian Astrophysical Observatory (SAO). The database also includes all 110 Messier

objects, 50 earth-orbiting satellites, 26 asteroids, and 15 periodic comets.

For more information on these electronic features, contact your Meade dealer, or send $3.00

to Meade Instruments for a copy of the Meade General Catalog,

Information on Meade dealers located near you can be obtained by calling toll-free: 1-800-62-

MEADE.

- 19 -

ADVANCED PRODUCTS DIVISION

Meade Instruments Corporation

World’s Leading Manufacturer of Astronomical Telescopes for the Serious Amateur

6001 Oak Canyon, Irvine, California 92618 ■(949) 451-1450

FAX: (949) 451-1460 ■www.meade.com

© 2000