Meade Lightbridge Laser Collimator Instruction Manual 01 LX 200 Rev F

: Meade Meade-Lightbridge-Laser-Collimator-Instruction-Manual-719761 meade-lightbridge-laser-collimator-instruction-manual-719761 meade pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

Instruction Sheet
Laser Collimator
For use with Meade's LightBridge Telescopes
Assembly
Please read the entire instruction sheet before using your Laser Collimator.
Meade's Laser Collimator simplifies the collimation process. Collimation is a method to align your telescope's optics. Your
telescope is aligned at the factory, but shipping and handling can sometimes misalign collimation. Misaligned collimation can
mean dimmer and blurrier images in your telescope eyepiece. Your instruction manual describes how to collimate your
telescope. Meade's Laser Collimator provides a simpler, second method of collimation.
Be aware of the following as you use your Laser Collimator:
Only turn on your laser when you are going to use it. All lasers use up battery power very quickly and have short battery life.
When you turn on the laser, only turn the "on screw" until the laser turns on. Do not overtighten this screw! Overtightening may
damage the collimator.
Note the small "doughnut" attached to your telescope's primary mirror. The doughnut is attached to help you perform alignment
with the Laser Collimator. When you insert the Laser Collimator into your eyepiece and turn it on, the pinpoint of laser light will
normally be close to or on top of this doughnut. However, if it is any distance away from the doughnut, perform the collimation
procedure described in your LightBridge instruction manual before you use the method described below.
DANGER: Invisible laser radiation. Avoid eye or skin exposure to direct or scattered radiation.

STEP 1:
Remove the eyepiece or eyepiece cap from the telescope.

STEP 2:
Point the laser downward. Turn the screw on the side of the laser until the laser turns
on. Do not overtighten this screw.

STEP 3:
Insert the laser collimator into the eyepie holder. Orient the window on the side of the
collimator so that it is pointing towards the bottom of the telescope. Tighten the
collimator in place using the eyepiece holder thumbscrew.
window

doughnut

STEP 4:
Standing at the side of the telescope, check out the primary mirror and look for the laser
pinpoint. If the laser pinpoint is not near or on the "doughnut" attached to the
mirror, remove the laser collimator and use the collimation method described in your
LightBridge telescope manual.
If the pinpoint is very near or on the doughnut, proceed to step 5.

STEP 5:
Using a Philips head screwdriver, adjust the one, two or all three tilt screws on the
secondary mirror holder until the the laser pinpoint is in the center of the doughnut.
Notice that when the pinpoint is on top of the doughnut that the pinpoint brightens considerably. When it is in the center, it dims again.

tilt screws

STEP 6:
Go to the bottom side of the primary mirror tube and look up at the Laser Collimator.
Adjust the one, two or three of the collimation screws on the bottom, until the pinpoint
in the window (see Step #3) of the laser collimator is in the center of the window. Note
that you will have to loosen one or all of the locking screws to tighten or loosen the
collimation screws.

locking
screw

pinpoint
misaligned

pinpoint
centered

collimation
screw

STEP 7:
Return to the secondary mirror holder and readjust the tilt screws, if necessary, to make
sure the pinpoint is centered in the doughnut. Your telescope should now be aligned.

(800) 626-3233

www.meade.com

14-7002-00 1/06



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Create Date                     : 2006:01:04 10:10:07
X Press Private                 : %%DocumentProcessColors:.%%EndComments
Producer                        : QuarkXPress(tm) 6.1
Creator                         : QuarkXPress(tm) 6.1
Title                           : 01-LX-200 rev F.qxd

EXIF Metadata provided by EXIF.tools