MediaTek RT3090-1T1R 802.11b/g/n 1T1R WLAN Mini Card User Manual H110UI1 USER S GUIDE

Download:
Mirror Download [FCC.gov]
Document ID	1276582
Application ID	iOjxgZhF8YNfkq7xux5rCA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.04kB (813059 bits)
Date Submitted	2010-05-05 00:00:00
Date Available	2010-11-02 00:00:00
Creation Date	2010-05-05 18:44:32
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2010-05-05 18:44:32
Document Title	Microsoft Word - H110UI1 USER'S GUIDE.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	julia.chu

Notebook PC
User’s Guide
Model: H110UI1
First Edition: March 2010
Draft Only
User's Guide
NOTICE
Specifications and information found in this guide are subject to change
without notice. Any changes therefore will be incorporated in future
editions. The manufacturer assumes no responsibility for errors or
omissions in this document.
TRADEMARKS
Windows™ is the trademark of Microsoft Corporation.
Intel® is the trademark of Intel Corporation.
Bluetooth® is the trademark owned by its proprietor.
Other trademarks are properties of their respective owners.
Page II
User's Guide
Standards
The following standards are adopted throughout this guide:
„
Notebook in boldface (with or without capitalization) refers to the notebook
computer that you have purchased.
„
Boldface type is also used to highlight important information in this
document.
„
Whenever extra caution is called for, the information will be boxed in a dark
frame preceded by "Note:" or "Warning:".
Page III
User's Guide
This page is left blank intentionally.
Page IV
User’s Guide
Contents
CONTENTS
CHAPTER 1 BEFORE YOU BEGIN....................................................................... 1-1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
CHECKING WHAT YOU RECEIVED ................................................................. 1-1
EXAMINING YOUR COMPUTER ....................................................................... 1-2
THE SYSTEM LED ......................................................................................... 1-7
THE FIVE STATUS LEDS ................................................................................ 1-8
THE POWER SWITCH WITH LED.................................................................. 1-10
THE  KEY............................................................................................. 1-11
OPERATING TEMPERATURE.......................................................................... 1-13
THE AC ADAPTER ....................................................................................... 1-14
CHAPTER 2 BATTERY............................................................................................ 2-1
2.1
2.2
2.3
2.4
2.5
2.6
2.7
BATTERY PACK.............................................................................................. 2-1
RECHARGING THE BATTERY PACK ................................................................ 2-1
QUESTIONS AND ANSWERS ........................................................................... 2-2
BATTERY MAINTENANCE............................................................................... 2-3
POWER CONSUMPTION ................................................................................... 2-3
REDUCING POWER CONSUMPTION ................................................................. 2-4
REMOVING THE BATTERY PACK .................................................................... 2-4
CHAPTER 3 MEMORY............................................................................................ 3-1
3.1
3.2
LIMITATION OF 32-BIT WINDOWS™ OS........................................................ 3-2
REMOVING MEMORY MODULE ...................................................................... 3-3
CHAPTER 4 WIRELESS LAN/BLUETOOTH MODULE ................................... 4-1
4.1
REMOVING WIRELESS LAN/BLUETOOTH MODULE ....................................... 4-1
CHAPTER 5 WWAN MODULE (OPTIONAL) ..................................................... 5-1
5.1
5.2
REMOVING WWAN MODULE ........................................................................ 5-1
INSERTING THE SIM CARD ............................................................................ 5-3
CHAPTER 6 THE HARD DISK DRIVE ................................................................. 6-1
6.1
REMOVING THE HARD DISK DRIVE .............................................................. 6-1
CHAPTER 7 THE EXTERNAL ODD (OPTIONAL)............................................. 7-1
Page V
Contents
7.1
7.2
User's Guide
CONNECTING THE EXTERNAL ODD TO THE SYSTEM .................................... 7-1
LOADING DISCS ............................................................................................. 7-2
APPENDIX A - AGENCY REGULATORY NOTICES........................................ A-1
Page VI
User's Guide
Before You Begin
Chapter 1 Before You Begin
Please read this section before you start using your computer.
1.1
Checking What You Received
Your notebook package should contain the following items:
(a)
(a)
(b)
(c)
(d)
(e)
(f)
(b)
Note:
(c)
(d)
(e)
The Notebook.
AC Adapter.
AC Power Cord.
CD Disc (Including Drivers, and User’s Guide).
Battery Pack.
External ODD (optional).
(f)
You should keep the original factory carton and packing materials in case you
need to ship the unit back for servicing.
Page 1-1
Before You Begin
1.2
User's Guide
Examining Your Computer
Before you start using your computer, you need to get acquainted with your notebook's
main features and interfaces:
Panoramic View
Internal Microphone
2-in-1 Media Card Reader (SD/SD-HC, MMC)
Webcam Lens
Speaker
Webcam LED
Touch Pad
Kensington Lock
Ventilation Holes
RJ45 LAN Connector
Keyboard
Two USB Connectors
LCD Screen
Power Switch with LED
Page 1-2
User's Guide
Before You Begin
Front View
Ventilation Holes
Speaker
Rear View
Battery Pack
Page 1-3
Before You Begin
User's Guide
Left View
DC-In Jack
HDD LED
DC-In Jack LED
USB Connector
VGA Connector
Headphone / Microphone Jack
Ventilation Holes
Right View
2-in-1 Media Card Reader (SD/SD-HC, MMC)
RJ45 LAN Connector
Power Switch with LED
Kensington Lock
Two USB Connectors
Page 1-4
User's Guide
Before You Begin
Bottom View
Battery Pack
Ventilation Holes
Speaker
Warning:
For better ventilation of heat generated and gathered inside the system unit,
you are advised not to block the ventilation holes. For notebook with
ventilation holes on the system chassis, please avoid putting system unit on
fabric surfaces when it is powered on. Fabric surfaces not only tend to
block the ventilation holes located on the system chassis, fabric threads
(especially from carpets and rugs) would invariably come off and get inside
the system unit which in turn would deteriorate the overall performance of
the system’s ventilation.
Page 1-5
Before You Begin
Note:
User's Guide
Some external USB devices consume more power than this system unit can
provide. In this case, these USB devices have their own power cords. To make
sure this kind of USB devices can function properly, please connect these
devices to the AC source first before connecting to the system unit.
Mono Connector Plug
Stereo Connector Plug
Two Types for Audio Jack
Headphone / Microphone Jack
Page 1-6
The system’s headphone jack supports both stereo and mono connection plugs.
User's Guide
1.3
Before You Begin
The System LED
The HDD LED
Below is how the LED would behave in different situations:
Note:
White
The system is accessing the hard disk drive.
Off
The system is not accessing the hard disk drive.
The HDD LED are located on the left side of the system unit. For exact
location, please refer to the Left View diagram in Chapter 1.2.
Page 1-7
Before You Begin
1.4
User's Guide
The Five Status LEDs
The DC-In LED
Below is how the DC-In LED would behave in different situations:
White
Amber
The system is running on AC power and the
battery is not inserted.
The battery is charging.
The Webcam LED
This LED would be lit when the Webcam is in use.
The Caps Lock LED
The LED would be lit when the keyboard is in Caps Lock mode. In
this mode, all characters you type are in uppercase.
The Wireless Button With LED
Press fn+ f12 to power on and power off the Wireless LAN/Bluetooth
module or the WWAN module, or any combination of these two
modules. The main purpose of this button is to provide you a quick
way to turn off the power of wireless connection functions when
entering venues like airplanes, airports, and hospitals where the usage
of wireless connection functions is prohibited or not advisable.
Below is how the Wireless Button with LED would behave in
different situations:
White
Amber
Either the Wireless LAN/Bluetooth module or
the WWAN module (or both of these two
modules) is powered on.
Both the Wireless LAN/Bluetooth and
WWAN modules are powered off.
The Speaker On/Off LED
This LED would be lit when the speaker is turned on.
Page 1-8
User's Guide
Note:
Before You Begin
For exact locations of these Status LEDs, please refer to the Panoramic View
and Left View diagrams in Chapter 1.2.
Page 1-9
Before You Begin
1.5
User's Guide
The Power Switch With LED
The Power Switch With LED
This Power Switch is programmable by the user. For details on how to program
this switch, please refer to the Power Options of Control Panel in Windows™
System. This switch has a LED indicator that shows whether the system is
powered on or not.
Below is how the power LED would behave in different situations:
Note:
On
The system is in full operation.
Off
The system is powered off.
Blinking
The system is in Sleep mode.
The Power Switch is located on the right side of the system. For exact location,
please refer to the Right View diagram in Chapter 1.2.
For more details on Sleep and Hibernate, please refer to Power Options (of
Windows™ System) in the Control Panel of your Microsoft™ Windows™
operating system.
Page 1-10
User's Guide
1.6
Before You Begin
The  Key
The  Function Key is located near the bottom-left corner of the keyboard. This key is
used together with other keys to activate certain pre-defined functions. To activate these
functions, press and hold down  together with the keys described below:
Opening the Help Menu
Press this key combination (fn+f1) for the Windows™ Help menu.
Brightness Decreasing
Press this key combination (fn+f2) to decrease the brightness of LCD display.
Brightness Increasing
Press this key combination (fn+f3) to increase brightness of LCD display.
LCD / External Monitor Switch
Press this key combination (fn+f4) to switch between LCD only, external
monitor only, and LCD/ external monitor simultaneously.
Media Previous Track
Press this key combination (fn+f5) to skip to the previous track/chapter of
media playback.
Media Play/Pause
Press this key combination (fn+f6) to play or pause media playback.
Media Stop
Press this key combination (fn+f7) to stop media playback.
Media Next Track
Press this key combination (fn+f8) to skip to the next track/chapter of media
playback.
Volume Decreasing
Press this key combination (fn+f9) to decrease the audio volume.
Page 1-11
Before You Begin
User's Guide
Volume Increasing
Press this key combination (fn+f100) to increase the audio volume.
Mute / Un-Mute Switch
Press this key combination (fn+f11) to mute and un-mute the audio volume.
Turning on Wireless Module
Press this key combination (fn+f12) to power on and power off the Wireless
LAN/Bluetooth and WWAN modules, or any combination of these two
modules.
Press this key combination (fn+ ) to break the MS-DOS application program
you are running. Its function is the same as the industry standard “break” key.
Print Screen Switch
Press this key combination (fn+ ) to capture the screen image. Its
function is the same as the industry standard “prt sc” key.
Page 1-12
User's Guide
1.7
Before You Begin
Operating Temperature
Operating Temperature
: 10ºC to 35ºC.
Page 1-13
Before You Begin
1.8
User's Guide
The AC Adapter
Connect to the system
Once the adapter is connected to a wall socket, it starts providing power to the system unit
as well as charging the battery.
Page 1-14
User's Guide
Battery
Chapter 2 Battery
2.1
Battery Pack
Your notebook is equipped with a high-energy rechargeable Lithium Ion (Li-Ion) battery
pack. Battery life will vary depending on the product configuration, product model,
applications loaded on the product, power management settings of the product, and the
product features used by the customer. As with all batteries, the maximum capacity of this
battery will decrease with time and usage.
2.2
Recharging The Battery Pack
Your notebook supports both on-line and off-line recharge. Follow the procedure below to
recharge battery:
• Make sure the battery pack is installed in the notebook.
• Connect the AC adapter to the notebook and to an electrical outlet.
When the notebook is OFF, a depleted Li-Ion battery will take three hours to recharge.
Page 2-1
Battery
2.3
Q:
A:
User's Guide
Questions And Answers
I can feel a mild heat next to the battery pack during recharge. Is it normal?
The battery will generate heat during recharging and discharging. There is a
protection circuit inside the notebook to prevent overheating. User needs not to
worry.
Q:
A:
My battery operation time is not as long as it should be. Why?
Q:
I did not use my spare battery for a few days. Even though it was fully recharged,
there wasn't as much power left as a newly charged one. Why?
A:
The batteries will self-discharge (1% per day for Li-Ion) when they are not being
recharged. To make sure a battery pack is fully charged, recharge before use.
Always keep the battery inside the notebook and have the AC adapter connected
whenever possible.
Q:
A:
I did not use my spare battery for months. I have problem in recharging it.
The battery is heat sensitive and can only be charged to its maximum if the battery
and its environmental temperature remain within 15-25°C (59-77°F). The more the
temperature deviates from this range during recharging, the less chance there is for
the battery to be fully charged. In order to recharge the pack to its full capacity,
users are requested to cool down the unit by unplugging the AC Adapter. Wait until
it is cooled down. Then plug in the AC Adapter to start recharging again.
If you happen to leave your battery pack to go through an extended period of selfdischarge, say more than three months, the battery voltage level will become too
low and needs to be Pre-Charged (to bring the battery voltage level high enough)
before it automatically (for Li-Ion only) resumes its normal Fast Charge. PreCharge may take 30 minutes. Fast Charge usually takes 2~3 hours.
Page 2-2
User's Guide
2.4
Battery
Battery Maintenance
To maintain the battery pack's maximum capacity, you should occasionally let the
notebook deplete its battery power completely before recharging.
To carry out a complete depletion of the battery, disconnect the AC adapter and let your
notebook consume the remaining battery power. To speed up the depletion, use the HDD
as much as possible, and the LCD should be set as bright as possible. When the battery is
empty, wait for the notebook to cool down (especially the battery). The temperature should
be within 15-25°C (59-77°F). Then insert the AC adapter to recharge the battery.
2.5
Power Consumption
The Windows™ operating system has incorporated the latest state-of-the-art ACPI
(Advanced Configuration Power Interface) power management methodology. In order to
fully utilize the power of your battery packs, it would be a good idea for you to spend
sometime to acquire a basic understanding of the power management concept from your
operating system.
In Windows™ Operating Systems, you can go through Power Options of the Control
Panel according to the version of Windows™ Operating System the notebook applies.
We shall not describe them in details.
Page 2-3
Battery
2.6
User's Guide
Reducing Power Consumption
Although your notebook (together with the operating system) is capable of power
conservation, there are measures you can take to reduce the power consumption:
• Use the AC power whenever possible.
• Lower the intensity of the LCD backlight. A very bright screen translates to higher
power usage.
• Try to use the HDD to read and write files, instead of using the external USB
ODD.
Note:
2.7
Whenever system is powered on or powered off, make sure the battery pack is
installed in the battery pack compartment.
Removing The Battery Pack
This battery pack can easily be removed and replaced. Make sure that the computer is
properly shutdown before changing the battery pack. If you would like to change the
battery pack while power is on, make sure this battery pack is not the only electrical source
to the system unit. Follow the steps below to remove the battery pack.
•
•
Battery Pack
•
•
To insert the battery pack, reverse the steps above.
Page 2-4
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Push the battery latch to unlock
position as shown by #1and #2.
Remove the battery pack as shown
by #3.
User's Guide
Memory
Chapter 3 Memory
Your notebook is equipped with a DDR3-800/DDR2-667 SO-DIMM configurable
memory unit. The table below illustrates the possible ways system memory can be
configured.
Total Memory
1024MB
2048MB
Socket
1024MB
2048MB
Groove for indicating the
orientation of the module
1.25” max
DDR3 S.O.DIMM Memory Module
Groove for indicating the
orientation of the module
1.25” max
DDR2 S.O.DIMM Memory Module
Note:
Depending on the edition of Windows™ operating system your notebook
applies, the minimum memory requirement would vary. It is recommended that
if you use Windows™ 7 operating system, your system memory should be at
least 1024MB.
Page 3-1
Memory
3.1
User's Guide
Limitation Of 32-bit Windows™ OS
Below description applies to 32-bit Windows™ OS only, unless otherwise specified. 32-bit
Windows™ OS is confined to the limitation of 4GB (232-1) of addressable memory space.
This would not be an issue when you use Windows™ to view the system memory. That is
when you have installed 4GB memory as listed above, Windows™ would report the system
memory to be 4GB.
However, if you installed 4GB memory and use other application programs to detect
memory size, the reported “available memory size” can be as low as 3GB.
There is no such limitation in 64-bit Windows™ OS.
Page 3-2
User's Guide
3.2
Memory
Removing Memory Module
Below is the procedure on how to remove the memory module.
•
•
•
•
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Remove the battery pack as shown
in Chapter 2.
Push the lock to the right as shown
to unlock the D-part.
•
Remove D-part as shown by #1.
•
Pull the spring-locks sideways as
shown by #1.
The memory module would pop up
as shown by #2.
Remove the memory module as
shown by #3.
Memory Module
•
•
Page 3-3
Memory
To insert the memory modules, reverse the steps above.
Page 3-4
User's Guide
User's Guide
Memory
This page is left blank intentionally.
Page 3-5
User's Guide
Wireless LAN Module
Chapter 4 Wireless LAN/Bluetooth Module
Your notebook is equipped with a Wireless LAN / Bluetooth module. The Wireless LAN
/ Bluetooth module supports the wireless LAN and Bluetooth function.
4.1
Removing Wireless LAN/Bluetooth Module
Below is the procedure on how to remove the Wireless LAN / Bluetooth module.
•
•
•
•
•
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Remove the battery pack as shown
in Chapter 2.
Push the lock to the right as shown
to unlock the D-part.
Remove D-part as shown by #1.
Wireless LAN/Bluetooth
module
Page 4-1
Wireless LAN Module
User's Guide
•
•
•
•
Disconnect the two cables as shown
by #1.
Remove the two screws as shown by
#2.
The Wireless LAN module would
pop up as shown by #3.
Remove the Wireless LAN module
as shown by #4.
To insert the Wireless LAN / Bluetooth module, reverse the steps above.
Note:
Page 4-2
Depending on the different types of the Wireless LAN / Bluetooth module,
some modules are with two cables, while other modules are with three cables.
User's Guide
WWAN Module (Optional)
Chapter 5 WWAN Module (Optional)
Depending on configurations, your notebook is equipped with an optional proprietary
WWAN module. The WWAN module supports WWAN (Wireless Wide Area Network)
function. In order for this WWAN module to carry out its intended function, in addition to
inserting the WWAN module, you also need to insert a SIM card into your system unit.
5.1
Removing WWAN Module
Below is the procedure on how to remove the WWAN module.
•
•
•
•
•
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Remove the battery pack as shown
in Chapter 2.
Push the lock to the right as shown
to unlock the D-part.
Remove D-part as shown by #1.
WWAN module
Page 5-1
WWAN Module (Optional)
User's Guide
•
•
•
•
Disconnect the two cables as shown
by #1.
Remove the two screws as shown by
#2.
The WWAN module would pop up as
shown by #3.
Remove the WWAN module as shown
by #4.
To insert the WWAN module, reverse the steps above.
Note:
Page 5-2
Depending on the different types of WWAN module, some modules are with
two cables, while other modules are with three cables.
User's Guide
5.2
WWAN Module (Optional)
Inserting the SIM Card
Below is the procedure on how to insert the SIM card.
SIM Card Slot
SIM Card
•
•
•
•
Make sure the system is properly shutdown.
Flip the system upside down as shown.
Remove the battery pack as shown in Chapter 2.
Insert the SIM card into the slot as shown.
Note:
The SIM card is designed to work with the WWAN module. Before use, please
make sure the WWAN module is also installed into the system unit.
Page 5-3
WWAN Module (Optional)
This page is left blank intentionally.
Page 5-4
User's Guide
User's Guide
The Hard Disk Drive
Chapter 6 The Hard Disk Drive
Your notebook is equipped with an industry standard 2.5”/9.5mm hard disk drive.
6.1
Removing The Hard Disk Drive
Below is the procedure on how to remove the hard disk drive.
•
•
•
•
•
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Remove the battery pack as shown
in Chapter 2.
Push the lock to the right as shown
to unlock the D-part.
Remove D-part as shown by #1.
Hard Disk
Page 6-1
The Hard Disk Drive
User's Guide
•
Page 6-2
•
Remove the four screws as shown
by #1.
Pull the handle in a lateral direction
to unlock the hard disk drive as
shown by #2.
•
•
Tilt up the hard disk drive as shown.
Remove the hard disk drive.
User's Guide
The Hard Disk Drive
•
•
Remove the four screws as shown
by #1.
Remove the HDD bracket from the
HDD drive as shown by #2.
To insert the HDD drive, reverse the steps above.
Page 6-3
The Hard Disk Drive
This page is left blank intentionally.
Page 6-4
User's Guide
User's Guide
The External ODD (Optional)
Chapter 7 The External ODD (Optional)
Depend on the model, your notebook may be shipped with an external ODD. You can
connect the ODD to an USB connector.
7.1
Connecting The External ODD To The System
The illustration below shows how to connect the external ODD to the system.
USB Connector
Page 7-1
The External ODD (Optional)
7.2
User's Guide
Loading Discs
ODD Indicator
Emergency Hole
Eject Button
Follow the steps below to load a disc.
1. When the system is powered on, press the eject button to open the disc tray.
2. Gently grasp and pull the disc tray until it is full opened.
3. Put the disc in the disc tray with the label side facing up.
4. Gently push the center of the disc tray until it locks into place.
Follow the steps below to remove discs:
1. Press the eject button and wait for the disc tray to partially open (when the ODD
indicator is off). Gently pull the disc tray out until it is full opened.
2. Gently unlock and lift the disc out of the disc tray.
3. Gently push the center of the disc tray until it locks into place.
Note:
Press the eject button will not open the disc tray when the system is off. In this
case, you can open the disc tray by inserting a paper clip into the emergency hole
next to the eject button.
Note:
If the disc is not seated properly when the disc tray is closed, the disc might be
damaged, and the disc tray might not open fully when you press the eject button.
Page 7-2
User’s Guide
Appendix A
Appendix A - Agency Regulatory Notices
A.1
Safety Instructions
CAUTION: Please read these safety instructions carefully.
CAUTION: Please keep this User's Manual for future reference.
CAUTION: Please disconnect this equipment from AC outlet before
cleaning. DO NOT use liquid or sprayed detergent for cleaning. Use a clean
moistened cloth.
CAUTION: The wall socket used should be positioned near the equipment
and should be easily accessible.
CAUTION: Please keep this equipment free from humidity.
CAUTION: Place the equipment on a reliable surface at all times. A drop or
fall can cause severe damage.
WARNING: The openings of the enclosure are for air ventilation and are
meant to protect the equipment from overheating. DO NOT COVER THE
VENTILATION OPENINGS.
Page A-1
Appendix A
User's Guide
CAUTION: Verify the voltage of the power source before connecting the
unit to any power outlet.
WARNING: DO NOT step on or place anything over the power cord.
CAUTION: All cautions and warnings on the equipment should be noted.
WARNING: If the equipment is not used for a long period of time,
disconnect the equipment from the power source to avoid damage from power
spikes.
WARNING: NEVER pour any liquid into any openings; a fire or electrical
shock is possible.
WARNING: For safety reasons, other than pre-designated ports, doors, and
the equipment should be opened only through qualified service personnel.
CAUTION: If one of the following situations should arise, the equipment
should be checked by an authorized technician:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to excessive moisture.
d. The equipment does not work well, or you fail to get it to work
according to user's manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
Page A-2
User’s Guide
Appendix A
CAUTION: DO NOT LEAVE THE EQUIPMENT IN TEMPERATURES
BELOW -20ºC(-4ºF) OR ABOVE 60ºC(140ºF). IT MAY CAUSE
DAMAGE TO THE EQUIPMENT.
WARNING: This computer contains an internal lithium battery-powered
real-time circuit. There is a risk of explosion and injury if the battery is
incorrectly replaced or handled. Do not attempt to recharge, disassembled,
immerse in water, or dispose of it in fire. Replacement should be done through
your notebook dealer.
WARNING: THE CD-ROM/DVD-ROM IN THIS NOTEBOOK
EMPLOYS A LASER SYSTEM.
a. To ensure proper use of this product, please read the relevant
instructions carefully and retain for future reference.
b. Should the unit ever require maintenance, contact your local dealer.
c. Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure.
d. To prevent direct exposure to Laser Beam, do no try to open the
enclosure.
CAUTION: The internal CD-ROM/DVD-ROM drive is classified as a
CLASS 1 LASER PRODUCT. Label is located on the outside of the CDROM/DVD-ROM drive with the following wordings:
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
Page A-3
Appendix A
User's Guide
WARNING: Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Explosionsgefahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch
denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des Herstellers.
WARNING: Your notebook contains a Ni-MH or Li-Ion battery pack.
There is a risk of fire and chemical burn if the battery pack is handled
improperly. Do not disassemble, crush, puncture, short external contact, dispose
of in water or fire, or expose it to temperature higher than 60ºC.
WARNING: Handle the battery pack very carefully. Avoid touching the
metal leads on the connector of the battery case.
CAUTION: Use only approved AC Adapter with your notebook. Using the
wrong type of AC Adapter may cause serious damage to your notebook.
CAUTION: The AC Adapter can accept a line voltage ranging from 100V to
240V and is compatible with most international power sources. If you are
unsure whether your power source is compatible, please contact the local dealer
for assistance.
CAUTION: For continued protection against risk of fire, Replace only with
same type and rating of fuse.
CAUTION: If the computer is not sold to German area, please use only the
local recognized power supply cords that are recommended by the
manufacturer.
Page A-4
User’s Guide
Appendix A
WARNING: Don't expose your notebook to excessive heat or coldness
(frost). Don't drop, spill fluids or open the exterior of the case. This can damage
the notebook and void the warranty.
Caution: This notebook computer contains a certified optical module that is
equivalent as a Class 1 LASER PRODUCT.
Caution: According to ANSI/NFPA 70 of the National Electrical Code
(NEC) Section 820.93, make sure that your CATV system installer has
connected the Co-axial cable shield to the grounding system of the building, as
close to the point of cable entry as practical. The common or earthed side of the
connected (SELV) circuits and any accessible metal parts should be connected
to the screen of coaxial cable.
Page A-5
Appendix A
A.2
User's Guide
Agency Notice
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio or television technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this
device that are not expressly approved by the manufacturer responsible for compliance may
void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI
connector hoods to maintain compliance with FCC Rules and Regulations.
Page A-6
User’s Guide
Appendix A
FCC RF Radiation Exposure Statement
•
•
•
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This EUT is compliant with SAR for general population/uncontrolled exposure limits
in ANSI/IEEE C95.1-1999 and has been tested in accordance with the measurement
methods and procedures specified in OET Bulletin 65 Supplement C.
If this device is going to be operated in 5.15 ~5.25GHz frequency range, then it is
restricted in indoor environment only.
USA and Canada Safety Requirements And Notices
The FCC with its action in ET Docket 93-62 has adopted a safety standard for human
exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified
equipment. The Intel PRO/Wireless LAN MiniPCI Adapter products meet the Human
Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper
operation of this radio according to the instructions found in this manual will result in
exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:
• Do not touch or move antenna while the unit is transmitting or receiving.
• Do not hold any component containing the radio such that the antenna is very close or
touching any exposed parts of the body, especially the face or eyes, while transmitting.
• Do not operate the radio or attempt to transmit data unless the antenna is connected; if
not, the radio may be damaged.
Use in specific environments:
• The use of wireless devices in hazardous locations is limited by the constraints posed
by the safety directors of such environments.
• The use of wireless devices on airplanes is governed by the Federal Aviation
Administration (FAA).
• The use of wireless devices in hospitals is restricted to the limits set forth by each
hospital.
Antenna use:
• In order to comply with FCC RF exposure limits, low gain integrated antennas should
be located at a minimum distance of 20 cm (8 inches) or more from the body of all
persons.
• High-gain, wall-mount, or mast-mount antennas are designed to be professionally
installed and should be located at a minimum distance of 30 cm (12 inches) or more
from body of all persons. Please contact your professional installer, VAR, or antenna
manufacturer for proper installation requirements.
Page A-7
Appendix A
User's Guide
Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (such as a wireless network device) near
unshielded blasting caps or in an explosive environment unless the device has been
modified to be qualified for such use.
Use On Aircraft Caution
Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency
wireless devices because their signals could interfere with critical aircraft instruments.
Canadian Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Avis Canadien
Cet appareil numerque de la classe B respecte toutes les exigences du Reglement sur le
materiel brouilleur du Canada.
Canada Radio Frequency Interference Requirements
This Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210,
Issue 4 (Dec. 2000).
“To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to licensing.”
Cet appareil numérique de la classe B est conforme à la norme NMB-003, No. 2, et CNR210, No. 4 (Dec. 2000).
“Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une
licence, il doit être utilizé à l’intérieur et devrait être placé loin des fenêtres afin de fournir
un écran de blindage maximal. Si le matériel (ou son antenne d’émission) est installé à
l’extérieur, il doit faire l’objet d’une licence.”
Page A-8
User’s Guide
European Union
Appendix A
Notice
Product with the CE Marking comply with the EMC Directive (2004/108/EC) and the Low
Voltage Directive (73/23/EEC) issued by the Commission of the European Community and
if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC).
Compliance with these directives implies conformity to the following European Norms (in
parentheses are the equivalent international standards and regulations):
• EN55022 (CISPR 22)⎯ Electromagnetic Interference
• EN55024 (IEC61000-4-2,3,4,5,6,8,11)⎯ Electromagnetic Immunity
• EN61000-3-2⎯ (IEC61000-3-2)-Power Line Harmonics
• EN61000-3-3⎯ (IEC61000-3-3)-Power Line Flicker
• EN60950 (IEC60950) ⎯ Product Safety
For devices with built-in wireless equipment, the following additional standards apply:
• ETSI301489-17: General Emissions for Radio Equipment
• EN60950: Safety
• ETSI300328-2: Technical Requirements for Radio Equipment
CE Caution: Due to the fact that the frequencies used by 802.11b/802.11g wireless
LAN devices may not yet be harmonized in all countries, 802.11b/802.11g products are
designed for use only in specific countries or regions, and are not allowed to be operated in
countries or regions other than those of designated use. As a user of these products, you are
responsible for ensuring that the products are used only in the countries or regions for
which they were intended and for verifying that they are configured with the correct
selection of frequency and channel for the country or region of use. And deviation from
permissible settings and restrictions in the country or region of use could be an
infringement of local law and may be punished as such.
Page A-9
Appendix A
User's Guide
The wireless LAN device can currently be used indoors only in the following departments
of mainland France.
01
02
03
05
08
09
10
11
12
16
19
2A
2B
21
24
25
26
27
32
35
Ain
Aisne
Allier
Hautes Alpes
Ardennes
Ariège
Aube
Aude
Aveyron
Charente
Corrèze
Corse Sud
Haute Corse
Côte d’Or
Dordogne
Doubs
Drôme
Eure
Gers
Ille et Vilaine
36
37
39
41
42
45
50
54
55
57
58
59
60
61
63
64
65
66
67
68
Indre
Indre et Loire
Jura
Loir et Cher
Loire
Loiret
Manche
Meurthe et Moselle
Meuse
Moselle
Nièvre
Nord
Oise
Orne
Puy du Dôme
Pyrénées Atlantique
Haute Pyrénées
Pyrénées Orientales
Bas Rhin
Haut Rhin
69
70
71
72
75
77
78
79
82
84
86
88
89
90
91
92
93
94
Rhône
Haute Saône
Saône et Loire
Sarthe
Paris
Seine et Marne
Yvelines
Deux Sèvres
Tarn et Garonne
Vaucluse
Vienne
Vosges
Yonne
Territoire de Belfort
Essonne
Hauts de Seine
Seine St Denis
Val de Marne
The wireless LAN device cannot currently be used in any departments of mainland France
other than those listed above.
Maximum allowable EIRP 802.11b wireless LAN cards in the mainland departments of
France not shown in the table above are as follows: (See the ART website at www.arttelecom.fr for information on the French overseas territories.)
Frequency Ranges (MHz)
2400 – 2446.5
2446.5 – 2483.5
Japanese Notice
Page A-10
Indoors
10 mW
100 mW
Outdoors
Not permitted
100 mW on private property
with Ministry of Defense
approval
User’s Guide
Appendix A
DGT Statement
Page A-11
Appendix A
This page is left blank intentionally.
Page A-12
User's Guide

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2010:05:05 18:44:32+08:00
Create Date                     : 2010:05:05 18:44:32+08:00
Format                          : application/pdf
Title                           : Microsoft Word - H110UI1 USER'S GUIDE.doc
Creator                         : julia.chu
Document ID                     : uuid:bfd60f64-3432-4487-bb19-a5f8fd1df851
Instance ID                     : uuid:c421be44-39af-45ef-8ae9-73fdf7f44313
Page Count                      : 54
Author                          : julia.chu

EXIF Metadata provided by EXIF.tools