Megaphoton H1-1000COBGAA ELECTRONIC BALLAST FOR HID LAMP User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3080444
Application ID	hX4PuXdruJ64A7G0FAQfBw==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	163.55kB (2044314 bits)
Date Submitted	2016-07-29 00:00:00
Date Available	2016-07-29 00:00:00
Creation Date	2017-12-11 06:10:10
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-11 06:10:10
Document Title	Users Manual
Document Creator	Adobe Illustrator CS6 (Windows)

USER MANUAL
for 400W/600W/1000W Metal Halide or High Pressure Sodium Lamps
USER MANUAL
USER MANUAL
USER MANUAL
1.Introduction
3.Product information
4.Wiring Diagram
(a) The interference potential of device or system:
“Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.”
(b) Simple measures that can be taken by the user
to correct interference:
“NOTE: This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. - Consult the
dealer or an experienced radio/TV technician for help.”
Thank you for purchasing Efinity Electronic Ballast. Please review
the following instructions to ensure you receive the best perfor
mance. Each ballast uses a high temperature,resin-sealed compo
nent board for completely silent operation. Each unit is burned-in at
the factory for approximately twelve hours to ensure maximum
reliability.
E-Ballasts use a micro-processor similar to your home computer.
This micro-processor allows the E-Ballast to run halide or sodium
lamps. It is programmed for a "soft-start" and does not require an
initial surge of power to light the lamp. This increase the lamp life
and allows the end user to start multiple ballasts ballasts at the
same time without tripping breakers. To ensure safe operation, this
Programmed for a "soft-start" and does not require an initial surge
of power to light or missing lamp.In case of auto-shutoff, please
disconnect from the power supply, remove the faulty lamp or check
for wiring problems,wait for some minutes then restart your ballast.
3.1. Technical specifications
Model
Version
Product weight
Dimensions (L*W*H)
Temperature case
Temperature ambient
Input voltage +/-10%
Input current at 100%
Input power at 100%
Power factor
Total Harmonic Distortion
Frequency
Power inlet
Power output settings
Ignition voltage:
Inrush current:
Plug type:
-Ballast Case must be Grounded
H1-1000COB-GAA
1000W 120V/240V
3.8kg/8.82lb
H1-600COB-GAA
600W 120V/240V
3.8kg/8.82lb
H1-400COB-GAA
400W 120V/240V
3.8kg/8.82lb
394mmx110mm x73mm 308mmx110mm x73mm 281mmx110mm x73mm
75 ℃ / 167℉
-20 ~ 40 ℃/ -4 ~ 104 ℉
120 V
240 V
120 V
240 V
120 V
8.60 A 4.30 A
5.60 A
2.80 A
3.59A
645 W
1085 W 1055 W 655 W
430 W
>0.99
< 10%
50 - 60 Hz
IEC C14
50%/75%/100%
5 kV
240 V
180 A
430W
≤37.5 Amps ≤50 Amps ≤37.5 Amps ≤50 Amps ≤37.5 Amps ≤50 Amps
Nema 5-15 Nema 6-15 Nema 5-15 Nema 6-15 Nema 5-15 Nema 6-15
3.2. Main Dimension
281mm(400W)
308mm(600W)
394mm(1000W)
2.Controls, connections and indications
73mm
58.5mm
A. Electronic ballast
B. Output connector
C. Power output selector knob
D. IEC connector for power cord
E. Power cord with either NEMA 5-15 or NEMA 6-15 plug
110mm
Electronic Ballast
USER MANUAL
Product Advantage
G ene ra tor re a d y
Runs MH or HPS la mps
High ef fic ien c y e lectro nic balla st
No a co ustic r e a sona nc e
Lower ha rmonic distrotion
High ou tput a nd improve d spectr um
Driver ef fic ien c y a t full power: 95-96%
Ligh t-we ight a nd high ener gy-ef fic ien t.
3.3. HOT SPOT
Tcase max=60°C/140°F
HOT SPOT
3.4 Environment
The product is meant for use in climate rooms. The product may be used in damp
environments. The product may not be used in wet environments or outdoors. The
1000 W lamps function optimal when the ambient temperature is between -20 ~ 40℃
/ -4 ~ 104 ℉.
NEMA 5-15
NEMA 6-15
5.Protections
1.End of Lamp Life(EOL)Protection
2.Short circuit protection
3.Open circuit protection
4.Ignition failure protection
5.Thermal protection
6.Warning
Power surge,power outage,outage overloading may stress or
damagethe lamp.As a safety feature,this Soft-Start technology
also reduces ballast damage caused by a bulb failure.In case of
an unexpected chut-off,please disconnect from the power supply,
remove the faultylamp,check for wiring problems,then plug-in the
ballast power cord.
NOTE: This device complies with Part 18 of the FCC Rules.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment. This product may cause
interference to radio equipment and should not be installed
near maritime safety communications equipment or other
critical navigation or communication equipment operating
between 0.45–30 MHz. If this occurs, please change outlet
or move the lamp far away from other appliance.
7.Disclaimer
Any of following circumstances, will not be Efinity’s warranty:
1.Install the product without following the wiring diagram in this
manual and cause the product damage.
2.Damaged by human reason (like product is soaked in water) or
caused by not following the manual instructions.
3.Install or use the product without following the local laws and regula
tions.
4.Cover the warrant logo personally, or the client /the third party tries
to maintain, repair, change the product and cause the damage.
5.Use of the environment does not meet the provisions of this manual.
6.Damaged by force majeure, like abnormal voltage, earthquake,
flood, fire, thunderstroke, transpor tation accidents, etc.
7.Man-made damage during carrying, transportation.
8.Damaged by unstable match from other company’ (not Efinity’s)
poor design or defective quality products.(like luminaire).
9.Beyond the warranty period
Electronic Ballast
USER MANUAL
for 400W/600W/1000W Metal Halide or High Pressure Sodium Lamps

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Warning                         : Invalid xref table

EXIF Metadata provided by EXIF.tools