MEIAN Technology FT-89R Wireless PIR detector User Manual FT 89R Wireless PIR detector

Shenzhen Meian Technology Co.,Ltd . Wireless PIR detector FT 89R Wireless PIR detector

Users Manual

External powered DC12VStatic current consumption: 18mAAlarm current consumption: 30mAWhen powered,the green LED light for 3 seconds and flicker 2 seconds and offthe red LED flicker about isseconds,after3 minutes,the detector comes into work states.Alarm mode:Red LED light about 3S Relay output:NCWireless transmitting distance:150mTransmitting frequency:433MHThe max recharge caurrent: 120mADetection range:12m(25 ) 3.Installation2 Specification3.1 GuideDo not face to cold or heat sourceDo not fact to sun light Keep away from high-voltage wire1.IntroductionInstallation baseshould be stableDo not face to metal wall FT-89R is the best indoor/outdoor motion detector with passive infrared and microwave.It's water proof and all weather resistant with two layer stable housings.FT-89R combines a variety of detection techniques which enable it to work in the most difficult environment where needs high security while maintaining immunity to false alarm.The infrared sensor adopts nice lens produce three-dimensinal thermal imaging of the protected area .Combinging the four-element microwave scanning contributes to an amazing detection capacity.Using this technique allows high sensitivity but lowest false alarm.FT-89R is equipped with unique protection mechanisms against any attempt to damage or to disable its operation.3.2 Disassemble guide2.Pull out the bottom of the cover3.Remove the PCB1.Loose screwInternal battery-poweredLow battery ararm:2t will send Low batteryreport when the detectoy low batteryand send battery resume report when the battery resumeRelay outpnt:N/O(when external powerdisconnect,the Rely output will convertto N/O from N/C afert powered by battery about 2 minutes,external power resume by contrary.)Static current consumption: 18mAAlarm current consumption: 80uA4.Remove the middle caseEnstarlationSuggest installation height:2-3 meters from ground45 cornerfixing Surface fixingA.Mark the drilling points and make holes.B.Draw the cable from back channelC.Fix the base cover on the wall with two screws.D.Put the PCB back on the cover with clips and fasten screws.Suggest corner installation3.3. Stand-by battery replacing and usingWhen battery is lower power, it will send related signalto control panel,so user should replace battery with same spec.(as right fig.)On BUS working mode,if this model of detector more than4pcs in the system,you need put battery inside to assurethe system will not overload.123Open battery box Install new battery Put on the coverand fix with svrewsWireless PIR Detectorz
3.8 Perform motion test to the detect ion area: install th e cover and close thefasten part (refer to the right diagram)1. Start the test at least 2 minutes after power supply2. Crossing to any direction of the detection area, your walking with 0.75m/s will cause the LED indicator to light for 2-3 seconds (refer to the right diagram)3 .Perform motion test from contrary directions in order to confirm the boundary of two sides. Make confirmed that detection center pointing to the center of protected area.4. Away from the detector 3 to 6 m, raise slowly your arm and reach into the detection zone, mark the lower limit of PIR detection. Do the same step to confirm the upper limit.5.the center of detection zone should not uphill incline. To obtain a good detection range , please adjust the vertical detection range, en-sure the detector is in a correct position.6. After MW sensitivity or detection angle are adjusted, walking test must be performed according to the above steps.3.4 Fanction explanation: Solar board connectorGreen LEDPretrigger LEDAnti-strong light switchBattery connectorTrigger plusechoose jumper switchTrigger pluse choose jumper switch 1Tamper switchWiring terminal Red LEDalarm LED 3.5 Function of jumper switch:Trigger pluse count,choose jumper switch 1,accroding to infrnred sensor 1 3.6 Wiring terminal+-AlarmTamp 12VPowerAlarmTamperAlarm:When the external power supply for 2-10 minutes,Alarm ouput is N/CAlarm:When the external power disconnect about 2-10 minutes,Alarm output convert to N/O on wireless modeOne Pluse Two PluseThree PluseTrigger pluse connt,choose jumper switch 2,accroding to infrnred sensor 2One Pluse Two PluseThree Pluse3.7 CodingWhenthe alarm panel enter coding mode,please press the tamper switch of FT-89R for 3 seconds,immediately thenloose,when you can hear a hing sonnd from panel ,which means coding successfally.FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu