MEIAN Technology MC-335R Wireless PIR Detector User Manual MC 335R Wireless PIR Detector

Shenzhen Meian Technology Co.,Ltd . Wireless PIR Detector MC 335R Wireless PIR Detector

Users Manual

拨码开关功能说明拨码开关Current consumption： Static≤30μA，Alarm≤20mA（433MHz） 4.2 pet-immunity guidebook The installation height of 2.2m to 2,4m is available pet-immunity height2.2-2.4m2.2-2.4m≤15Kgthe pet is smaller than 15kgthe top of the detecting area is the non-pet-immunityareaNOOK2.2--2.4m2.2-2.4m≤20Kg15。the pet is smaller than 20kgprevent direct the places where the pets can clamb up XP/N 20110301-2MC-335R Wireless PIR Detector4.3 Introduce DIP function:MC-355R can choose 3 kinds of pulse as follows:1-pulse： Alarm 1-pulse.2-pulse: Alarm 2-pulse。3-pulse： Alarm 3-pulse(Factory default)。Higher pulse counting and lower catch performance and can avoid false alarm 1 2Modes1-pulse2-pulse3-pulseON ON OF F OFF OFF OF F
6. Customer service Our products are very reliable，but for some special reasons, the working performance will be limited in certain range. We here list some cases as follows： ①. The voltage of control panel is not stable； ②. Low-voltage of the detector.For any help please contact with our company and your could visit our website for more information.Warning: We are not responsible for the problem caused by improper operation by users!① Set as Test Mode to precess walk-test,pulse count set as 1,2 or3。 ④ Make sure the detection centre at the proper place. Should properly adjust the detection area if you can not get an ideal detection area.② Walk across the far edge of coverage area at the speed of 1 step/second(about0.75m/s) The LED will flash for seconds then alarm（as shown in the right figure）5. Walk test in coverage area:⑤ After adjust the detection angle , should redo the walk test as above.⑥ Please change TEST mode to NORMAL mode after the Walk-test .③ Do walk-test in opposite direction to confirm the boundary of both sides, Make sure the detection centre pointing to the centre of protected area.MC-355R can set three modes as follows:Test Mode：Emitting alarm signa nce detector is triggered. No time-lag between two emissions.Power-saver mode：Send detection signal of detector and battery status Coding Mode：Press tamper switch for more than 3 seconds and send an identification code to receiver. Dip switch 3 and 4 set modesModesON OFF TestOFF ON Power-saverOFF OFF Coding34Press the tamper switchfor study the ID code Insert one new battery4.4. Coding method between detector and control panel:① Coding set：Install the battery LED flashes，whenthe detector gets stable after seconds，press tamper switch for more than 3seconds and detector will send a wirelesssignal. If the control panel receives thesignal and give the response sound then code successfully. Please refer to controlpanel manual for details.② If short-circuit pin “A” with a jumperthen the tamper alarm function invalid. 4.5. Detection distance adjustment and battery changes① Shorten detection distance by pushing down the PCB and vice versa User can adjust it to meet different need. As shown on the right picture, the detection distance is the farthest.②When the signal between detector and control panel becomes weak. That means a low battery condition. Users should change new battery with same type. Pull out the base cover and change battery.Please pay attention to the positive and negative.P/N 20110301-2FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. nce detector is trigg eredl oo

Navigation menu