MEILOON CPS Wireless Speaker Amplifier User Manual Wireless Speaker Amplifier

Meiloon Industrial Co., Ltd. Wireless Speaker Amplifier Wireless Speaker Amplifier

Users Manual

Wireless Speaker Amplifier Owner’s Manual for OEM Caution: This user guide information is only provided to OEM or module installer. Do not supply to end user. 1. Introduction The CPS 8Wi Wireless Speaker Amplifier is a radio device that transmits and receives radio signals in accordance with the spectrum regulations for the 2.4GHz unlicensed frequency range. The following table shows a major function. Frequency Band: 2403.3~2479.1MHz Power Supply: DC 12V from the testing board Channel Employed: 20 channels Modulation technology: FHSS Modulation Type: FSK Antenna Type: Dipole Antenna Radio Frequency Chipset: WHAM2 Module LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following “Contains TX FCC ID: R48CPS If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE: This equipment complies with IC RSS-102 and FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. OEM integrator is still responsible for testing their and product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC
authorization. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. If the size of the end product is smaller than 8x10, FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following “Contains TX FCC ID: R48CPS. If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu