Merrytek Technology MC612VDRC Lighting Control Switch User Manual MC612V D RC

Download:
Mirror Download [FCC.gov]
Document ID	3775381
Application ID	yRlNuvQadrk+JTdxc7ZNZg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	177.88kB (2223516 bits)
Date Submitted	2018-03-10 00:00:00
Date Available	2018-03-12 00:00:00
Creation Date	2018-01-31 11:38:19
Producing Software	Corel PDF Engine Version 17.1.0.572
Document Lastmod	2018-03-10 15:14:45
Document Title	MC612V D RC 说明书.cdr
Document Creator	CorelDRAW X7
Document Author:	Administrator

GENERAL
GUIDELINES
FOR
INSTALLATION
MC612V D RC
INSTALLATION
1, The sensor should be installed by a qualified electrician. And ensure
Main sensor installation
that the electricity supply is switched off before installing or servicing
Install the sensor on the LED
plate by using 2 screws
the product.
Detachable sensor installation method 1
Make two holes on the LED plate , push
the sensor into the holes.
Main sensor installation
Detachable sensor installation method 2
Install the sensor on the LED
plate by using 2 screws
Step 1: Cut the following buckle
and the little part off.
2, The company does not accept responsibility for any consequences
resulting from unauthorized modification of the product.
the little part
0.55in/14mm
the following
buckle
3, MC612V D RC should be connected to a stable power supply of
Lighting Control Switch USER’S MANUAL
120/277Vac, 50Hz/60Hz.
The hole
dimension:
φ 0.12in/3mm
4, Microwaves cannot pass through metal or brick walls if thicker than
3mm
(0.12in)
20cm. They will pass through thinner walls but there will be some
Model No.:MC612V D RC
Step 2: Place the sensor towards to the
floor and fix it on the LED plate by screws.
The hole of the wire is 0.15in/3.7mm.
The hole
dimension:
9mm
(0.35in)
attenuation.
5, Installation inside a glass or plastic housing will result in a reduction of
detection sensitivity. Expect a reduction of approximately 20% for every
M0.12x0.31in/3.0x8mm Screw
2X
M0.12x0.31in/3.0x8mm Screw
2X
M0.1x0.31in/2.5x8mm Screw
2X
3mm of thickness.
6, The sensor is designed for indoor use only. The raining or wind blowing
may trigger the Lighting Control Switch even if without human motion when
WIRING SCHEME
outdoor use.
7, Detection area will be affected by speed of motion,height of installation and
volume of moving object.
8, Daylight sensor was tested on sunny environment with no lampshade.
INSTALLATION & WIRING
MC612V D RC
The sensor has 6-position terminal blocks :
L(Phase) N(Neutral) L’ (Switched phase / control)
0-10V(+,-) (Connected to 0-10V interface)
SEC
0-10V Dimmable
LED Driver
The sensor is designed for installation at 8.2ft ~ 26.2ft
/2.5-8m in height.
Use 10-18 AWG copper wire only, both solid and stranded
MC612V D RC
MI20180131A0
FEATURES
DETECTION PATTERN
● Sensor parameters can be conveniently set by a remote controller.
SETTINGS
Slow walk
Fast walk
● The mini motion detector is separately from sensor power part, it
will be easier to fix motion detector on the surface of tri-proof light
and hidden the power part behind it.
● This sensor is particularly designed for the lights which have limited
space, for examples, LED linear, batten, and LED tri-proof lights.
100%
75%
50%
25%
100%
75%
50%
25%
32.8ft 26.2ft 19.7ft 13.1ft 6.6ft
10m 8m
6m
4m
2m
6.6ft 13.1ft 19.7ft 26.2ft 32.8ft
6m
8m
10m
2m 4m
32.8ft 26.2ft 19.7ft 13.1ft 6.6ft
10m 8m
6m
4m
2m
6.6ft 13.1ft 19.7ft 26.2ft 32.8ft
6m
8m
10m
2m 4m
Detection area, hold time and daylight sensor can be set by using DIP switches
on the sensor. Note that reducing the detection area will also reduce the sensitivity.
1, Detection area
I: up to 100%
II: up to 75%
III: up to 50%
IV: up to 25%
4,Stand-by dimming level
This is the pre-setting dimming level you
would like to have after the hold time in
the long absence of people.
I: 10%
II: 20%
III: 30%
IV: 40%
40%
● Using pluggable design between motion detector and power part,
easy to reinstall or maintain.
● 0-10V interface can match up with Merrytek stand-alone daylight
Mounting height:9.8ft/3M
harvesting sensor Ms01.
SPECIFICATIONS
Operating voltage
120/277Vac, 50/60Hz
Rated Load
120Vac 50/60Hz 3.6A Ballast;
277Vac 50/60Hz 3.4A Ballast
HF system
5.8GHz±75MHz, ISM wave band
Transmitting power
<0.5mW
Power consumption
≤1.0W(stand-by)
Detection Range(Diameter)
39.4ft/12m Max.
Max. Mounting height
26.2ft/8m
Hold time
Sensor: 8S/30S/1min/5min/10min/15min/30min
Remote control: 8S/1min/5min/15min/30min
Stand-by Period
Sensor: 0S/1min/3min/5min/10min/30min/+∞
Remote Control: 0S/1min/5min/30min/+∞
Stand-by DIM Level
Sensor: 10%/20%/30%/40%
Remote Control: 10%/20%/30%/40%/50%
Daylight sensor
Slow walk
Fast walk
Sensor: 5lux/15Lux/30Lux/50Lux/100lux/150lux/Disable
Remote Control: 5lux/15Lux/50Lux/150lux/Disable
Operating temperature
-35˚C~70˚C
IP rating
IP20
100%
75%
50%
32.8ft 26.2ft 19.7ft 13.1ft 6.6ft
10m 8m
6m
4m
2m
100%
75%
50%
6.6ft 13.1ft 19.7ft 26.2ft 32.8ft
6m
8m
10m
2m 4m
32.8ft 26.2ft 19.7ft 13.1ft 6.6ft
10m 8m
6m
4m
2m
6.6ft 13.1ft 19.7ft 26.2ft 32.8ft
6m
8m
10m
2m 4m
Mounting height:19.7ft/6M
(Note: Please do not set the detection sensitivity to 25% when mounting at the height of 19.7ft/6m)
Slow walk
Fast walk
100%
32.8ft 26.2ft 19.7ft 13.1ft 6.6ft
10m 8m
6m
4m
2m
100%
6.6ft 13.1ft 19.7ft 26.2ft 32.8ft
6m
8m
10m
2m 4m
32.8ft 26.2ft 19.7ft 13.1ft 6.6ft
10m 8m
6m
4m
2m
6.6ft 13.1ft 19.7ft 26.2ft 32.8ft
6m
8m
10m
2m 4m



E489677
5,Daylight sensor
The sensor can be set to only allow the lamp to
illuminate below a defined ambient brightness
threshold. The settings are as follows:
8S
3, Stand-by period
Refers to the time period the lamp remains at
a pre-setting dimming level before it completely
switches off in the long absence of people.
I: 0s
II: 1min
III: 3min
IV: 5min
V: 10min
VI: 30min
VII: +∞
* When set to “+∞ ”mode, the low light is maintained until motion is detected.
Mounting height:26.2ft/8M
(Note: Please do not set the detection sensitivity to 25%/50%/75% when mounting at the height of 26.2ft/8m)
UL file number
2, Hold time
Refers to the time period the lamp remains at
100% illumination after no motion is detected.
I: 8s
II: 30s
III: 1min
IV: 5min
V: 10min
VI:15min
VII:30min
I: 5lux, darkness operation only
II: 15lux, darkness operation only
III: 30lux, twilight operation
IV: 50lux, twilight operation
V: 100lux, twilight operation
VI: 150lux,twilight operation
VII: Disable
*When set to Disable, the daylight sensor will switch on the lamp when motion
is detected regardless of ambient light levels.
*It should be set to Disable mode if the motion sensor is connected to
stand-alone daylight sensors.
NOTE1
Remote Control Setting
Button
Description
Name
Sensor module
Metal fitting
Transmit
Uploads the settings
Detection Area
25%/50%/75%/100%
Side wave
Hold time
The timeout from 100% to dim
8S/1min/5min/15min/30min
Main wave
Daylight Threshold
5Lux/15Lux/50Lux/150Lux/ Disable
Stand-by period
The timeout from dim to off
0S/1min/5min/30min/+∞
Stand-by DIM level
10%/20%/30%/40%/50%
Press “Reset” button for factory testing purpose only.
Reset
Detection
Area
Hold
Time
Daylight
sensor
Stand-by
period
Stand-by
dim level
100%
1min
Disable
3min
20%
Press this button to set the current suitable
daylight threshold.
Ambient Threshold
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
Permanent ON/OFF
ON-OFF
When the microwave module is built into a metal lighting luminaire or installed in a sensor near
a wall, the side wave will be reflected by the metal base or the wall. It can disturb the main wave.
As the result of this, the microwave motion senor might not perform optimally. Reducing the
detection sensitivity or the side wave will help to solve such problems.
FCC Warnning:
A. Movement Motion detect 9.8ft~19.7ft/3-6m
B. Presence detect 9.8ft~19.7ft/3-6m
C. Presence detect with daylight harvesting 9.8ft~19.7ft/3-6m
D. High mounting: 19.7ft~49.2ft/6-15m
E. High mounting with daylight harvesting : 19.7ft~49.2ft/6-15m
Auto mode
Microwave detection includes two parts called main wave and side wave. Main wave normally
detects the motion signal. Side wave does not effect motion detection but might disturb main
wave if the microwave motion sensor is built-in a sealed metal luminaire as microwave can not
pass through metal.
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution:
Adjust the light level when motion detected.
Dim+ / Dim -
4 optional quick settings
1/2/3/4
Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
*Note 1: MH02 is a common used remote control for a various of sensor, MC612V D RC only
works under Mode A.
*Note 2: 1/2/3/4: These 4 optional quick setting are factory default settings, see table chart 1
below.
1. Factory default settings:
According to the default settings, short press 1/2/3/4, then press
to transmit.
2. Modification:
Short press 1/2/3/4 number key, select your own sensor settings such as "Detection Range /
Hold Time / Daylight Sensor / Stand-by Period / Stand-by Dimming Level" , then press
to
transmit.
3. Save the modification:
After you have set the customized parameters, long press the numeric keys 1/2/3/4 number
key for more than 3s and will save the current settings to the 1/2/3/4 number key.
Quick
Setting
Detection
Area
Hold
Time
Daylight
sensor
Stand-by
period
Stand-by
dim level
100%
100%
100%
100%
8S
8S
1min
5min
Disable
5Lux
15Lux
50Lux
0S
1min
1min
30min
10%
10%
10%
10%
As the control angle of the Infrared Remote Control is fixed (30°), if the
sensors are installed too close to each other, the settings of both sensors will
be configured. Please refer to the below chart for the distance of the
installation of each sensor:
Mounting height
Distance between each sensor
26.2ft/8m
14ft/4.28m
19.7ft/6m
10.5ft/3.2m
9.8ft/3m
5.2ft/1.6m
8.2ft/2.5m
4.3ft/1.32m
The load will
not illuminate Load has failed.
Power is switched off.
Continuous movement in the
detection area.
French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le
fonctionnement.
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit
être installé et utilisé à distance minimum de 20cm entre le radiateur et votre corps.
Remedy
Adjust setting.
Replace load.
Switch on.
Check detection area setting.
The load is
The lamp (containing sensor) is
permanently installed in an area too close to
illuminated. reflective surfaces, i.e. metal,
glass or concrete walls.
1, Make sure installation area
suitable with at least 30cm space
between lamp and surrounding
reflective surfaces.
2, Reduce sensitivity (detection area).
The load will
Speed of moving object is not in
not illuminate
the range of 0.5-3m/s or the
despite
detection radius is too small.
movement.
Check detection area setting.
The remote The battery on the remote
control is not control is run out.
The remote control is not
working.
aligned with sensor.
may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
Déclaration d'exposition aux radiations
FAQ
Cause
English: This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two
installed and operated with minimum distance 20cm between the radiator & your body.
Distance between each sensor
Incorrect daylight
sensor setting selected.
ISED Statement
conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that
(Table chart 1: 1/2/3/4 Quick Setting for MC612V D RC)
Question
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Motion sensor
Motion sensor
15° 15°
Shenzhen Merrytek Technology Co..Ltd
No.3 Building, 380 Xiangshan Avenue, No.3 Industrial Park Luotian, Songgang Town, Bao’an District, Shenzhen 518105, Guangdong, China
www.merrytek.com
Change the battery.
Change the remote angle.
Email:sales@merrytek.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Administrator
Create Date                     : 2018:01:31 11:38:19+08:00
Modify Date                     : 2018:03:10 15:14:45+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Format                          : application/pdf
Creator                         : Administrator
Title                           : MC612V D RC 说明书.cdr
Creator Tool                    : CorelDRAW X7
Metadata Date                   : 2018:03:10 15:14:45+08:00
Producer                        : Corel PDF Engine Version 17.1.0.572
Document ID                     : uuid:845f1348-673c-4c5a-bfc4-40901864963e
Instance ID                     : uuid:b6dbb688-53c5-4e7c-baa1-0764e780395e
Page Count                      : 2

EXIF Metadata provided by EXIF.tools