Mesa Laboratories ANA Wireless Analog Sensor User Manual M5ZANA User s Man

Download:
Mirror Download [FCC.gov]
Document ID	308540
Application ID	aQjNNiX448CNmKefiUF7Aw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.31kB (141359 bits)
Date Submitted	2003-03-10 00:00:00
Date Available	2003-03-10 00:00:00
Creation Date	2003-03-10 13:42:32
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2003-03-10 13:42:32
Document Title	Microsoft Word - M5ZANA_User's-Man_.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Katie

FCC ID: M5ZANA
Installation and Operation Instructions for the Point Sensor Analog transmitter.
Point Six, Inc.
Wireless Analog Sensor Model Point Sensor Analog
Installation and Operation Instructions
The Point Sensor Analog wireless analog level sensor transmits a digital value
representing either 0-20 MilliAmp, 0-5Volt or 0-10Volt levels and a unique serial
number to a 418 MHz receiver. The Point Sensor Analog is enclosed in a high impact
ABS enclosure for direct surface mounting in the environment to be measured. Point
Sensor Analog is battery operated
Application: Apply the sensor to a surface to with double-sided adhesive tape. Make
sure that the side labeled with FCC ID is visible and away from any metal surfaces.
Service Function: The wireless analog sensor has an installation mode switch. A
momentary push of this switch will start the convert/transmit cycles. When new and until
this button is pushed the Point Sensor Analog will not transmit. The Point Sensor
Analog will transmit a special installation status mark in the data packet immediately
after the installation/start switch is pushed. After the start a push of the installation
switch will result in the immediate transmission of data and ID and installation status
mark.
Battery: A 3.6 Volt lithium battery powers the Point Sensor Analog wireless sensor.
The battery will last for more than 10 years in the idle state (as shipped from the
manufacturer). The Point Sensor Analog will transmit data for as long as 10 years at a
rate of once each minute once started. The Point Sensor Analog is completely covered
with a water resistant conformal coating to protect the electronics from the environment
and condensation. The user may replace the battery. The Point Sensor Analog may be
placed in a quiescent state (battery life greater than 10 years) by holding the installation
switch closed for more than 4 seconds.
FCC ID: M5ZANA
MADE IN USA
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESERED OPERATION
FCC ID: M5ZANA
Point Sensor Analog Data Format
The Point Six, Inc. 418 MHz wireless sensors require a compatible receiver with the
ability to receive, error check and provide RS232 and RS422/485 interface. This
document describes the data format provided by the HA8-wow 418 MHz. Receiver.
The transmit packet from a receiver is approximately 15 milliseconds in duration and
consists of 13 bytes of data:
1-byte ID/Mode field
8-byte serial number
2-byte analog level as a 12-bit number
2-byte CRC-16 error check
The HA8-wow receiver processes this packet. The receiver performs a CRC-16 error
check on the packet. If the data is not accurate it is discarded. When a packet is received
that is error free it is converted to a 29-character packet and transmitted out the serial port
at 19,200 Baud. The data is transmitted serially in ASCII Hex format and terminated with
a CR character. This format requires two bytes for each byte of data; 14 data bytes x
2=28 plus the CR is 29 characters. See the HA8-wow specification for details.
The resulting binary data format of the packet is:
1-byte ID field
this field will contain a byte whose LSBit indicates the service
state of the transmitter, 0=normal, 1=service mode.
8-byte serial#
this field contains the serial number of the 1-Wire sensor.
2-byte data
this field contains the analog data as a 12-bit
number stored MSB first. A value of 0FFF is a full scale reading
and represents 20 milliamp. A zero input level will result in a
reading of 0000.
2-byte CRC-16
this is the originally received data packet CRC as described above.
1-byte checksum
the checksum is a mod 256 sum of all the ASCII character values
in the response but does not include the CR
FCC ID: M5ZANA
Example:
C1283FA60B000000EC000F8AD0AB
This field is the mode indicator, the LS-bit which indicates the
service state of the transmitter, C1=normal, C0=service mode.
C1283FA60B000000EC000F8AD0AB 
This field is the unique serial number of the 1-Wire sensor.
C1283FA60B000000EC000F8AD0AB 
This is analog data field stored MSByte first as a 12-bit number in
a 16-bit field. The number shown is 000F (15) or 15/4096 of full
scale. If this is a 0-20 milliamp input this would be .07 MilliAmp.
If the input is 0-5 Volts this would be 0.0183 Volts.
C1283FA60B000000EC000F8AD0AB 
This field is the CRC-16 error check as was originally received and
checked. This CRC is over the first 11 bytes of the packet starting
with the mode flags and ending with inclusion of the temperature
data.
C1283FA60B000000EC000F8AD0AB 
This field is the mod 256 sum of all the ASCII character values in
the response but does not include the .
C828AE9105000000AA2D2DD474AB 
This is the CR terminator, 0Dhex.
FCC ID: M5ZANA
FCC Radio Frequency Interference Statement
Point Sensor Analog
FCC ID: M5ZANA
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15, Subpart B, of the FCC Rules. This
equipment generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may cause interference
to radio communications.
The limits are designed to provide reasonable protection against such
interference in a residential situation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
ƒ
ƒ
ƒ
ƒ
Reorient or relocate the receiving antenna of the affected radio or television
Increase the separation between the equipment and the affected receiver.
Connect the equipment and the affected receiver to power outlets on separate
circuits.
Consult the dealer or an experienced radio/TV technician for help.
MODIFICATIONS
Changes or modifications not expressly approved by Point Six Inc. could void
the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2003:03:10 13:42:32-05:00
Modify Date                     : 2003:03:10 13:42:32-05:00
Page Count                      : 4
Creation Date                   : 2003:03:10 18:42:32Z
Mod Date                        : 2003:03:10 18:42:32Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Katie
Metadata Date                   : 2003:03:10 18:42:32Z
Creator                         : Katie
Title                           : Microsoft Word - M5ZANA_User's-Man_.doc

EXIF Metadata provided by EXIF.tools