Micro Star MS5654 PND User Manual 5654manual en

Download:
Mirror Download [FCC.gov]
Document ID	948235
Application ID	9MdDSQj0WO+cLl/Y0SrThQ==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	243.72kB (3046537 bits)
Date Submitted	2008-05-29 00:00:00
Date Available	2008-05-29 00:00:00
Creation Date	2008-03-10 17:21:10
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2008-05-29 12:09:27
Document Title	Microsoft Word - 5654manual_en.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	frankhuang

MS-5654
User guide
IMPORTANT
Satellite signals are required for this product to function in Navigation
Mode. There may be occasions within your home or surrounding area when
the signal strength is limited and Navigation Mode may not be possible.
This is quite normal for products of this type. If you experience difficulty in
receiving a signal in your car you may need to use an external antenna
(optional).
Safety
The Global Positioning System
The Global Positioning System (GPS) is a satellite based system that provides
location and timing information around the globe. GPS is operated and controlled
under the sole responsibility of the Government of the United States of America,
who are responsible for its availability and accuracy. Any changes in GPS
availability and accuracy, or in environmental conditions, may impact the
operation of your Personal Navigation Device (PND).
Using Your PND in the Car
When using your PND while driving it is essential that you drive with due care
and attention. Never modify the settings or program your PND while driving. Only
look at the PND map when it is safe to do so. Only follow the PND instructions
when the road regulations allow you to do so. When mounting the PND in your
car make sure that it does not obscure your view or impede the operation of any
driving controls.
Prohibited Areas
Do not operate your PND in hospitals or near any electrical medical
equipment.
Do not operate your PND in aircraft.
Do not operate your PND in a petrol station forecourt.
Battery
Your PND uses a Li-ion battery. Do not use it in humid, wet or corrosive
environments. Do not operate or store your PND in high temperatures (>60℃) or
in direct sun light. Do not pierce or break the battery casing.
Failure to follow these cautions will invalidate the warranty and may
cause the battery to leak acid, become hot, explode or ignite and
cause injury or damage.
If you come into contact with leaked battery acid wash the contact
area thoroughly and seek medical attention.
The Li-ion battery contained in this unit must be recycled or disposed of properly.
Do not dispose of in household waste or burn.
CONTENTS
IMPORTANT.............................................................................................2
Safety........................................................................................................2
The Global Positioning System .......................................................................2
Using Your PND in the Car ..............................................................................2
Prohibited Areas...............................................................................................2
Battery..............................................................................................................2
CONTENTS..............................................................................................3
Getting Started .........................................................................................4
Position of the controls ....................................................................................4
Car Adapter ......................................................................................................6
External Antenna (sold separately)..................................................................6
Switching On/ Off .............................................................................................6
Sleep Mode......................................................................................................7
Connect to PC..................................................................................................9
GPS ........................................................................................................10
Safety Instructions .........................................................................................10
Handsfree ...............................................................................................11
Paired List ......................................................................................................11
Dial .................................................................................................................13
Last Calls .......................................................................................................14
Auto Answer ...................................................................................................15
Travel Kit ................................................................................................16
Music..............................................................................................................16
Video ..............................................................................................................18
Photo..............................................................................................................21
UnitConverter .................................................................................................24
Currency Converter........................................................................................25
Settings...................................................................................................26
Display ...........................................................................................................27
Language .......................................................................................................29
Restore...........................................................................................................30
System Info ....................................................................................................31
Firmware Upgrade (advanced feature)..........................................................32
FM Adjust .......................................................................................................33
Technical Specifications .........................................................................35
Getting Started
This device combines GPS functionality with a photo viewer and Bluetooth
Hands-free. Before you begin to install and use this product, please read this
manual carefully for fully exploiting the functions of this product. If you experience
any problems, go through the user guide before contacting the customer helpline.
Position of the controls
1. Power Button
2. SD Card Slot
3. Touch Panel
4. Menu Button
5. Indicator Light*
6. TMC Antenna Jack
7. USB Port
8. Strap Hole
9. Battery Switch
10. Headphone Jack
11. External GPS Antenna
Port
12. Speaker
13. Stylus Pen/ Slot (Slide
the stylus pen out of
the slot when needed.)
*: When charging the light will be red; when fully charged the light will become green.
** When not using the unit for a long period of time, you are advised to turn the unit off by this
switch. Use the stylus to operate the switch.
Battery Information
The device is integrated with a 1000mAH/ 3.7V Li-polymer battery. It allows the
unit to be used for approximately 2 hours, without being connected to a power
source.
The battery icon which is shown at different point on the display depending on
which screen is currently being displayed. The icon indicates the current battery
status.
: means the battery capacity is full.
: means the battery capacity is 80%.
: means the battery capacity is 60%.
: means the battery capacity is 40%.
: means the battery capacity is 20%.
You can also go to the Main Menu / Settings / Power Status to view the actual
percentage of the remaining battery capacity.
The display shows the “Low Battery!” message automatically. When the battery
capacity drops below 15%, this message will be shown for 2 seconds. However,
when battery capacity drops below 5%, this message will stay on the screen until
the user connects the unit via the car charger or the battery capacity becomes
too low to power the unit.
Charging the Battery
Before using your PND for the first time, we recommend you to charge the unit
for 5 hours via the USB cable or 2 hours via the car charger in order to charge
the battery.
Plug the USB cable or the car charger into the USB socket
When you use the PND in your car, we recommend that you always use the car
charger in order to maintain the battery level.
*Disclaimer: some laptops could have insufficient power through the USB port to
charge the unit; this could lead to damage to your laptop USB port. MS-5654 will
not be held in any way responsible for the damages caused to any laptop by
charging the device through the laptop USB port
*It is recommended that when charging via the USB cable that the power switch
is set to the Off position.
When the device is connected to the car charger/USB cable the battery icon will
change to
, and LED indicator light on the front of the unit will be lit red.
When the battery is fully charged, and the car charger/USB cable is still
connected. The icon will change to
, and the LED indicator light on the front of
the unit will turn green.
Car Adapter
When using your PND in the car we recommend that you always use the in-car
charger to power the unit, especially on long journeys.
Plug the in-car charger into the USB socket on the unit. Plug the other end of the
adapter into the car’s cigarette-lighter / 12V DC socket.
External Antenna (sold separately)
If the GPS receiver fails to acquire a valid signal when mounted in your car it may
be due to a heat reflecting coating or heating elements in your windscreen. In
these cases use an external antenna.
The antenna has a magnet and can be positioned in various locations in or
outside your car to obtain the best signal reception. Push the antenna into the
socket on the rear of the unit until it clicks into place. Then position the antenna
so that you receive a valid signal.
Position the antenna on the roof of your car
Plugs into the back of the PND
*External Antenna Optional
Switching On/ Off
Use the stylus pen to switch the unit on by the power switch on the bottom of the
unit. You will see the booting screen for a short while, then the screen will change
to show the below message to warn you about driving safety. Tap on the
button to continue.
The screen will then change to the Main Menu screen shown below. This is the
starting point for using all of your MS-5654 features.
Sleep Mode
You can use Sleep mode to conserve battery power if the unit is not going to be
used for a short while, for example if you have scheduled a stop at a service
station. NOTE: if the unit is not to be used for a long period of time, the unit
should be switched off by the On/Off switch.
Press the Power Button for 3 seconds to put the unit into Sleep Mode.
Press the Power button for 3 seconds to wake up the device, the display show
the same screen as when the unit was put into sleep mode.
SD Card Installation
If you have a SD or MMC memory Card, you may install it to extend the storage
capacity of the unit, or to view photos saved on the card. When installing it can
only be fitted one way – the wording side facing towards you and the cut-off
corner at the bottom as shown. Insert the card and push it in so that it clicks into
place.
Insert a SD card into the slot, and you will see the below message.
If you need to remove the SD card, push the card in and it will eject from the slot.
You will then see the below message.
Note: the card slot can also be used as a card reader, refer to the following
section to operate the unit as an SD card reader..
Connect to PC
You can connect the unit to a PC for transferring data. Insert a SD/ MMC card to
the card slot; you can then use the unit as a card reader.
1. Power on the unit.
2. Plug B-type end of the supplied USB cable to the mini USB port on the unit,
then plug the other end into your computer.
3. The system will try to recognize and connect to the device; the unit display will
show the below screen.
4. Once the device has been connected to you will find 2 new USB devices
under ”My Computer”. The second device represents the memory card slot,
and is only available when a SD/ MMC card is inserted. Copy or move the data
needed between your PC and the unit.
GPS
You have chosen a cutting-edge navigation system. Congratulations! Please
enjoy using it. This navigation system leads you straight to your destination,
whether you are travelling by car or on foot. You can navigate and plan your
route with an easy-to-use and intuitive interface, just by using your finger or the
stylus. You can also use this application to plan your trip to suit your personal
preferences and interests and to save interesting destinations before you set off
on your journey. This manual leads you through the main features of the system.
Safety Instructions
y The driver’s attention should always be on the road. If you are the driver of the
vehicle, we do not recommend you to operate this unit while driving. Plan your
route before departure and pull over if you need to change route parameters.
y The MS-5654 has a built-in Safety Mode that will prevent you from using the
screen functions if your car is in motion. Unless a passenger will be the only
one to operate the MS-5654, we strongly encourage you to turn on the Safety
Mode.
y It is also important that you look at the display only if it is absolutely safe to do
so.
y You should always observe traffic signs and road geometry before obeying
instruction from the MS-5654.
10
Handsfree
This device can be linked to a mobile phone as a Bluetooth Hands-free device.
After being linked to a mobile phone, you can use the MS-5654 to call and
answer the phone without holding your mobile phone. Tap on the Hands-free
icon on the Main Menu to enter.
To operate the Hands-free function, tap on Bluetooth option to switch it on. You
will see a message as below. Remember the passkey for later usage.
Then you can see the menu as below.
Paired List
To use the Hands-free function, you have to pair the device with a mobile phone
first. If the MS-5654 has been paired with any mobile phone, you can see it on
Paired List. If the Paired List option is dark in colour and can not be entered,
that means there is no paired phone.
Follow the procedure below to pair your phone with the device.
1. Switch on the Bluetooth feature on your mobile phone and on your MS-5654. A
pop-up message will prompt to tell the passkey, 0000.
11
2. Place the MS-5654 and your phone nearby, and press relative keys on your
phone to make it search for new devices.
3. When the searching is complete, you should see a new device named
“MS-5654” on the list.
4. Select it from the list, and then your phone will ask you to enter a passkey.
Enter 0000 as the pop-up message prompts. Then the MS-5654 is now on the
paired list of your phone.
5. Select the MS-5654 and press the required buttons to connect it. Now you can
see your phone on the paired list of the MS-5654.
6. Or you can also connect your phone and the MS-5654 via the MS-5654 when
you want to operate the Bluetooth feature. Tap on the phone name in the
button to start connecting.
paired list of the MS-5654 first and then tap on
You will see the “Connecting” message on the display.
7. Your phone will ask if you want to accept the connection request from the
MS-5654. Press Yes to continue. You will see the “Connection Completed!”
message on the display.
8. If you want to disconnect the Bluetooth connection, press the relative buttons
on your phone to disconnect it from the MS-5654.
9. If you connected several phones to the MS-5654, the Paired List will list them
all. If need be, tap on a phone name and tap on
the device list. A confirm window will prompt, tap on
tap on
to cancel and exit.
12
button to delete it from
button to delete, or
Dial
Once a phone is paired and connected to the MS-5654, the Hands-free features
of the MS-5654 are now enabled. You can dial from and answer your phone via
the MS-5654.
Tap on Dial to begin entering a number to dial out, you will see the number pad
as below.
Tap to enter the phone number you want to call, and then tap on the
button. If a number is dialled wrong, tap on
once to erase a digit at a time.
While dialling, the display will change to the below.
Wait until the call is answered, then the MS-5654 becomes a Hands-free device.
You do not have to hold the phone, nor the MS-5654 to make the phone call. This
13
is useful when you are driving a vehicle.
button to hang up the call.
y Tap on
y Tap on
y Tap on
button to mute the volume.
y Tap on
button to adjust the volume.
button to mute your voice.
When a phone call is received while the MS-5654 and your phone are connected,
you will see the below screen appear. The name or number of the caller will be
shown on the first line of the display.
y Tap on
button to answer the call.
y Tap on
button to hang up the call.
y Tap on
y Tap on
button to mute the ring volume.
y Tap on
button to adjust the volume.
button to mute your voice.
Note: if Auto Answer is set to On, the call will be answered automatically after 3
seconds automatically.
Last Calls
The device records also the dialled calls, answered calls, and missed calls. You
can look them up and make a phone call to any of them when needed.
Dialled Number
If you have made a call via the MS-5654, you will see the number in the list.
14
y Tap on a number and then tap on
button to call that number again.
if you want to delete the number from the list. A message will
y Tap on
prompt you to confirm.
Answered Calls
If you have answered a call via the MS-5654, you will see that number on the list.
y Tap on a number and then tap on
button to call the number back.
y Tap on
if you want to delete that number from the list. A message will
prompt you to confirm.
Missed Calls
If there are any incoming calls that you did not answer, you will see the numbers
on the list.
y Tap on a number and then tap on
button to call the number back.
if you want to delete the number from the list. A message will
y Tap on
prompt you to confirm.
If there are no numbers recorded in a list, you will see the “No record!” message
on the display.
Auto Answer
The MS-5654 supports answering incoming calls automatically, tap on Auto
Answer to set it to On/Off. If it is set On, any received call will be answered
automatically after 3 seconds. If it is set Off, then you have to tap on the
button to answer the call when it comes.
15
Travel Kit
This device integrates several multimedia programs. You can watch video clips,
view photo, and also listen to music. Enter each function to enjoy your media
files.
Music
This device supports MP3, WMA formats. Enter "Music" function to read music
list.
Note 1: if the music file was saved into the Memory card, enter the Memory card
folder to find it.
Note 2: if the music file was saved into a specific folder, enter the folder to find it.
Note 3: press Menu button to go back main menu.
Tap on the screen to select a file from the list to play; you will see the display
shows as below.
y Tap
once to pause the playback.
y Tap
once to play the previous track. Or press it longer to rewind the
playback and find the section you need.
16
once to skip and play the next track. Or press it longer to fast-forward
y Tap
the playback and find the section you need.
once to select the repeat mode.
y Tap
to set Repeat One.
Tap
Tap
to repeat all.
to play the files once in regular sequence.
Tap
y Tap on
button to mute the volume.
y Tap on
button to adjust the volume.
17
Video
This device supports MPEG4, WMV formats. Enter Video function to watch video
clips.
Note 1: if the video clip was saved into the Memory card, enter the Memory card
folder to find it.
Note 2: if the video clip was saved into a specific folder, enter the folder to find it.
Note 3: press Menu button to go back main menu.
Enter Video function, you will see the figure as below, supported video clips will
be listed.
You can set to preview the selected clip. If the
clip will be played in thumbnail. Press the
icon is activated, the tapped
icon to play it in full screen. If you
, the tapped clip will be played in full
tapped again to make the icon become
screen without previewing.
Tap on the
icon to enter Settings. You can select if to resize the clip to fit the
screen for watching. And you can set the Zoom Mode to be Letter Box or Pan
Scan. Tap on
to apply and exit the settings.
18
Tap on the
icon to read the information of the software company.
Tap on the
icon to view the detail information of the selected clip.
Once a clip is selected and being playing, you can tap on the screen to call the
function buttons.
19
y
: Tap on this button to pause the playback. Tap on
to resume to play.
: Tap on these buttons to adjust volume. Tap on
to mute.
: Tap on this button to set playing mode as Random or Ordinal.
: Tap on this button to set repeat mode as Repeat Loop, Repeat One, or
Repeat List.
: Tap on this button to go to the list and find a file to open.
20
Photo
This device supports jpg, bmp, png, gif formats (up to 12MegaPixel file). Enter
"Photo" function to see thumbnails for all the photo files.
Note: press Menu button to go back main menu.
icon on the list, it means that photo is unsupported. Tap on
If you see an
a photo you want to view, and then you can tap on the left or right triangle to view
the previous or next photo.
To view pictures (bmp and jpeg formats only) from a SD card:
1) Copy all the pictures you want to view into the SD card.
2) Insert the SD card into the slot. In Photo thumbnails list, tap on "SD Card"
folder to enter.
3) You will see thumbnails of photos on the card, view and operate as you do to
photos on unit.
Tap on the photo, you will see Exit
and More
and lower corner of right side. Tap on
buttons on the upper
button to go to previous level menu.
Tap on
button to open the Tool Bar. After 5 seconds idling, the buttons and
the tool bar will disappear, tap the photo again to see and operate the buttons.
21
Slideshow
Tap on the
button to view the photos show one by one automatically.
After tapping on the
button, slideshow tool bar will prompt instead.
y Tap on
button again to stop slideshow.
y Tap on
button to set the slideshow interval among 2, 3, and 5 seconds.
y Tap on
button to mute the touch tones.
y Tap on
button to adjust the touch tones.
Rotate
Tap on
y Tap on the
again.
y Tap on
button to rotate the current photo.
button again to rotate the photo by 90 degree clockwise
button to restore the photo and zoom in.
22
Zoom in
Tap on
y Tap on the
button to zoom in the photo.
button to zoom in.
y Tap on the
button to zoom out. When the photo is zoomed in, you can
tap and drag it to view the part you need.
y Tap on
button to restore the photo.
Note: when the zoom in or zoom out limitation is met, the zoom in/ zoom out
button will become in gray color and not selectable.
23
UnitConverter
This device integrates a UnitConverter tool. You can use it to easily convert the
units of area, distance, speed, temperature, and weight.
Note: press Menu button to go back main menu.
button to select one option from measurement categories, depends
Tap on
on the unit you need to convert.
For example, if you want to convert cm to m , select Area.
Then tap on the number buttons to enter value To delete last digit, tap on
button. Then tap on
button, you can see the converted value.
The source and target units are both selectable. In this example, tap on cm and/
or m button to select another unit to meet your need.
24
Currency Converter
This device integrates a Currency Converter tool. You can use it to easily convert
the currency.
Note: press Menu button to go back main menu.
The source and target currencies are both selectable. Tap on either button to
select the needed source and target currencies.
After currencies are selected, you have to set the currency rate. Tap on
button to enter Currency Rate setting page.
Tap on the number buttons to set the rate of the source and target currencies. To
button. After entering, tap on
button to save the
delete last digit, tap on
currency rate for further usage. And the device will go back to the previous menu.
Tap on the number buttons to enter the digits of source currency. To delete last
digit, tap on
value.
button. Then tap on
button, you can see the converted
25
Settings
NOTE: You do not need to enter the Settings menu before you start to navigate.
Tap on the Settings icon on the Main Menu, the following screen is displayed.
To exit this page or any subsequent page, tap on the Exit
upper-right corner of the screen or press the menu button.
button at the
The
and
button means there are more options available. Tap on one of
them to scroll through the list to view the other options.
Note: when there is no option above/ below, the
grey in colour and is no longer selectable.
button will become
Volume
Tap 'Volume' you can modify the volume level of the Touch tones and the
hands-free volume. You can increase or decrease the level by clicking
. Click
or
to mute the volume.
You can also check or un-check the Touch Tones, to enable or disable having
the beep sound when you touch the screen.
Note: when the minimum or maximum volume level is met, the volume down/
volume up button will become grey in colour and is no longer selectable.
26
Display
Tap on the Display option to enter display submenu. There are 3 tabs to select
and adjust: Brightness, Backlight Timeout, and Screen Calibration.
Brightness: With this item, you can change the brightness of the screen. Adjust it
darker or brighter by tapping
or
button.
Note: when the minimum or maximum brightness level is met, the level down/
level up button will become grey in colour and is no longer selectable.
Backlight Timeout: Select an option to set the idling time to shut down the display
to save battery power. If you want it to display continuously, select “Never”.
Screen Calibration: This function calibrates the unit to respond to your screen
taps. You will need to use this function only if the unit begins to respond
inconsistently to your screen taps. Tap on
27
button to start.
Follow the on screen directions to tap on the centre of the cross to calibrate.
When the steps are done, you will see the second screen, tap on the screen to
save and apply the new calibration settings.
28
Language
Tap to select a language from the list to suit your need.
Power Status
Enter this option to find out the battery power status.
While charging, the status will be in motion, and de-noted “Charging”.
If the battery is fully charged and the unit is still on charge, the display will show
as the figure below.
29
Restore
This is to allow you to restore the settings back to default values. When
necessary, tap on the “Restore” option.
button to restore all the settings back to default. After this has been
Tap on
done, the message “Finished!” will be displayed.
Or tap on
to cancel and exit.
30
System Info
Tap on ‘System Info’ to access information about the unit and any inserted
memory card. There are 2 tabs to select and read: Devices and Storage.
Devices: The Devices page shows information about your software version and
capacity of the embedded internal memory.
Storage: The Storage page tells you the total capacity and free capacity of your
storage card (if installed) and the flash disk. If no storage card is installed, the
information will show as N/A.
31
Firmware Upgrade (advanced feature)
You can upgrade the firmware of the unit for better performance or/ and more
functions. Follow the steps below to do so.
Note 1: only advanced users are recommended to operate this feature.
Note 2: before upgrading, please make sure that the battery capacity if filled, or
power the unit with the car charger to ensure the upgrading will not be
corrupted by power failure.
Note 3: do not remove the memory card during upgrading!
Note 4: please visit www.binatonecarrera.com for more information.
1. Download the firmware file from our website. Uncompress the file and copy it
to a SD/ MMC memory card. Insert the card into the card slot of the unit.
2. Tap to enter this option; you will see the screen as shown below on the right.
3. To start upgrading, tap on the
button. The unit will restart automatically
and the “Upgrading…” message will be shown. A few seconds later, the
“Finished!” message will be shown after the upgrading is done.
4. If the upgrade is failed, you will see the below screen, which shows the
“Failed!” message.
32
FM Adjust
The device has a FM broadcasting function. Enable this function, you can
broadcast audio signal of the device, GPS voice and Music tracks playing on the
device, then receive with the FM radio on your car, and output with the speakers.
Enter this setting, you can see 2 options. Tap to select Speaker option to let the
device output audio by itself. Or tap on FM Transmitter option to set the device
broadcast the audio signal to a FM frequency.
When FM Transmitter is selected, you will see the figure below. Here you can
adjust the frequency to broadcast.
Adjust a frequency to broadcast by tapping on the two triangles. Four frequencies
are able to be saved for further usage. After a frequency is adjusted, tap on the
button. You will see a window asking to select a number to save the
frequency. Tap to select a number, then the frequency is selectable on the list.
You can select it from the list when you need to broadcast the audio of the device
next time.
Note: select a frequency with no available station, or the audio signal will be
covered.
33
34
Technical Specifications
Model Name
MS-5654
Display
480 x 272 WQVGA Resolution
4.3” TFT with Touch Panel
Centrality A3 372MHz
Microsoft Windows CE 5.0 Core Version
1G/2G Onboard NAND Flash ROM
64 MB SDRAM
SD Card (Memory type only)
Embedded 15x15 mm patch antenna
External GPS connector x 1
External TMC connector x 1
3.5mm Stereo Headphone Jack x 1
2.5mm Headphone Jack x 1(for TMC)
Integrated 1W Speaker (Mono)
Video playback function
TMC GNS(FM6)
FM Transmitter
Bluetooth function
1500mAH(Max)/3.7V Li-polymer battery
Battery Life: 3 Hrs for GPS
Stylus
USB 1.1
Digital photo stored in SD card should be displayed
Power Button x 1
Battery switch x 1
Menu Key x 1
Charger LED (Yellow -charger/ Green-finish)
Operator:0~50 Degree
Storage:-10~60 Degree
USB Sync Cable
Car charger
Cradle for device
Holder
CD
Manual x1
TMC external antenna x1
(H x W x Depth) (mm): 131 x 78 x 19.8
Below 205 g (w/ battery)
Processor
Software
Memory
Card Slots
GPS antenna
Audio
Special
Power
Input
Interface
Digital frame
Buttons
System / Power
Indicator
Temperature
Standard
Accessory
Dimension
Weight
35
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
RF exposure warning ·
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
This equipment must be installed and operated in accordance with provided instructions.
The equipment must not be co-located or operating in conjunction with any other antenna
or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:05:29 12:09:27+02:00
Create Date                     : 2008:03:10 17:21:10+08:00
Metadata Date                   : 2008:05:29 12:09:27+02:00
Document ID                     : uuid:3d403460-5b4f-4a9e-ad5f-96b88ca4c980
Instance ID                     : uuid:0c5bab42-6c85-41e1-938e-53182cea01d3
Format                          : application/pdf
Title                           : Microsoft Word - 5654manual_en.doc
Creator                         : frankhuang
Has XFA                         : No
Page Count                      : 36
Author                          : frankhuang

EXIF Metadata provided by EXIF.tools