Micro Star MS6871 Bluetooth USB Hub User Manual

Micro Star International Co Ltd Bluetooth USB Hub Users Manual

Users Manual

MICRO-STAR INT’LMS-6871 (v1.X)Bluetooth USB Hub
FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limits for a class Bdigital device, pursuant to part 15 of the FCC rules. These limits are designed toprovide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radio communications. Op-eration of this equipment in a residential area is likely to cause harmful interference,in which case the user will be required to correct the interference at his own expense.Notice 1The changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Notice 2Shielded interface cables and A.C. power cord, if any, must be used in order tocomply with the emission limits.VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AURESEAU.FCC ID: I4L-MS6871This device complies with part 15 of the FCC Rules. Opera-tion is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) This de-vice must accept any interference received, including inter-ference that may cause undesired operation.FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limits for a class Bdigital device, pursuant to part 15 of the FCC rules. These limits are designed toprovide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radio communications. Operationof this equipment in a residential area is likely to cause harmful interference,in which case the user will be required to correct the interference at his own expense.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one ormore of the following measures:— Reorient or relocate the receiving antenna.— Increase the separation between the equipment and receiver.— Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.— Consult the dealer or an experienced radio/TV technician for help.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the the radiator and your body. Notice 1The changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Notice 2Shielded interface cables and A.C. power cord, if any, must be used in order tocomply with the emission limits.VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AURESEAU.
FCC RequirementThis equipment complies with Part 68 of the FCC Rules. On the bottom of thisequipment is a label that contains, among other information, the FCC registrationNumber, Ringer Equivalence Number (REN) and USOC jack type for thisequipment. You must, upon request, provide this information to your telephonecompany.An FCC compliant telephone cord and modular jack is provided with this equipment.This equipment is designed to be connected to the telephone network or premisewiring use a compatible modular jack which is Part 68 compliant. See installationinstructions for details.The REN is useful to determine the quantity of devices you may connect to yourtelephone line and still have all of those devices ring when your telephone numberis called. In most, but not all areas, the sum of the REN of all devices connectedto on line should not exceed five (5.0). To be certain of the number of devices youmay connect to your line, as determined by the REN, you should contact your localtelephone company to determine the maximum REN for your calling area. If yourtelephone equipment causes harm to the telephone network, the Telephone Com-pany may discontinue your service temporarily. If possible, they will notify youin advance, but if advance notice is not practical, you will be notified as soon aspossible. You will be informed of your right to file a complaint with the FCC.Your telephone company may make changes in its facilities, equipment, operationsor procedures that could affect the proper functioning of your equipment. If theydo, you will be notified in advance to you an opportunity to maintain uninter-rupted telephone service.If you experience trouble with this telephone equipment, please contact MICRO-STAR INTERNATIONAL for information on obtaining service or repairs. Thetelephone company may ask that you disconnect this equipment from the networkuntil the problem has been corrected or until you are sure that the equipment is notmalfunctioning.This equipment may not be used on coin service provided by the telephone com-pany. Connection to party lines is subject to stat tariffs.
Copyright NoticeThe material in this document is the intellectual property of MICRO-STARINTERNATIONAL. We take every care in the preparation of this document, butno guarantee is given as to the correctness of its contents. Our products are undercontinual improvement and we reserve the right to make changes without notice.TrademarksAll trademarks used in this manual are the sole property of their respective owners.Pentium is a registered trademark of Intel Corporation.Windows is a registered trademark of Microsoft Corporation.Revision HistoryRevision Revision History DateV 1.0 First Release Oct. 2004with IVT SolutionFCC ID: I4L-MS6871This device complies with part 15 of the FCC Rules. Operationis subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) This devicemust accept any interference received, including interferencethat may cause undesired operation.
Important Safety PrecautionsAlways read and follow these basic safety precautions carefully when handling anypiece of electronic component.1. Keep this User’s Manual for future reference.2. Keep this equipment away from humidity.3. Lay this equipment on a reliable flat surface before setting it up.4. The openings on the enclosure are for air convection hence protectsthe equipment from overheating.5. All cautions and warnings on the equipment should be noted.6. Never pour any liquid into the opening that could damage or causeelectrical shock.7. If any of the following situations arises, get the equipment checked bya service personnel:zzzzzThe USB cable is damagedzzzzzLiquid has penetrated into the equipmentzzzzzThe equipment has been exposed to moisturezzzzzThe equipment has not work well or you can not get it workaccording to User’s ManualzzzzzThe equipment has dropped and damagezzzzzIf the equipment has obvious sign of breakage8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENTUNCONDITIONED, STORAGE TEMPERATURE ABOVE 600C ORBELOW -200C, IT MAY DAMAGE THE EQUIPMENT.
ਥᏵҬ೯೽եф౗ᆅ౛ᒤݤೕۓǺಃΜΒచ࿶ࠠԄᇡ᛾ӝ਱ϐեф౗৔ᓎႝᐒǴߚ࿶೚ёǴϦљǵ୘ဦ܈٬Ҕޣ֡όளᏰԾᡂ׳ᓎ౗ǵуεф౗܈ᡂ׳চ೛ीϐ੝܄ϷфૈǶಃΜѤచեф౗৔ᓎႝᐒϐ٬Ҕόளቹៜ०ૐӼӄϷυᘋӝݤ೯ߞǹ࿶ว౜Ԗυᘋ౜ຝਔǴᔈҥջଶҔǴ٠ׯ๓ԿคυᘋਔБளᝩុ٬ҔǶ߻໨ӝݤ೯ߞǴࡰ٩ႝߞೕۓբ཰ϐคጕႝߞǶեф౗৔ᓎႝᐒ໪הڙӝݤ೯ߞ܈π཰ǵࣽᏢϷᙴᕍҔႝݢᒟ৔܄ႝᐒ೛ഢϐυᘋǶ
CONTENTS1. Introduction ................................................................................................... 11.1 Bluetooth Technology .............................................................................. 11.2 MSI™ Bluetooth USB Hub ..................................................................... 11.3 Hardware Specifications ........................................................................... 22. Installation .................................................................................................... 52.1 Package Checkup ...................................................................................... 52.2 Software Installation ................................................................................. 52.3 Hardware Installation ............................................................................... 63. Software Operations ..................................................................................... 73.1 Introduction to BlueSoleilTM .................................................................... 73.2 Basic Operations ..................................................................................... 103.3 Getting Started ........................................................................................ 173.4 BlueSoleil User Guides .......................................................................... 324. Technical Support ........................................................................................ 455. Glossary ....................................................................................................... 47
User’s Guide11. Introduction1.1 Bluetooth TechnologyThe term “Bluetooth” refers to a worldwide standard for the wireless ex-change of data between two devices. In order to exchange data, two Bluetoothdevices must establish a connection. Before a connection is established, onedevice must request a connection with another. The second device accepts (orrejects) the connection.The originator of the request is known as the client. The device that ac-cepts (or rejects) the request is known as the server. Many Bluetooth devices canact as both client and server.A client Bluetooth device runs a software program that requests a connec-tion to another device as part of its normal operation. For example, the programmay request a connection to a remote computer, a printer, or a modem. Becominga Bluetooth client normally requires an action by the device operator, such as anattempt to browse a remote computer, print a file, or dial out on a modem.Every Bluetooth device that provides a service must be prepared to re-spond to a connection request. Bluetooth software is always running in thebackground on the server, ready to respond to connection requests.1.2 MSI™ Bluetooth USB HubMSI BTUB (Bluetooth USB Hub) is designed for providing wirelessconnectivity and USB 2.0 Hub function. Integrating a bluetooth module, it be-comes a Bluetooth-enabled USB hub. It extends one HUB port of PC / Notebookto 3 USB ports and 7 Bluetooth device notes. It fully supports Wide Range SelfPower Mode for USB 2.0/1.1/1.0 Devices. The rich profiles enable Bluetooth USB Hub to communicate withBluetooth mouse / keyboard / keypad / game pad supporting HID and exchangephoto/voice file with Bluetooth embedded Cellular phone. The coverage for theBluetooth Keypad is around 10 meters.
2MS-6871 Bluetooth USB Hub1.3 Hardware SpecificationsHardwareHW Interface 1 Upstream cable (USB Series A Plug) 3 Downstream USB connectors (USB Series A Receptacle) Compliant USB 2.0 / 1.1 / 1.0 Compliant Bluetooth 1.2 / Bluetooth 1.1 Class 2 Complaint Dimension Appearance: 73.5 x 73.5 x 21.5 mm USB Cable 90 cm including the connector PVC cover 3Kgf – 1 minutes Pull Test Weight 69g Antenna Type Printing circuit antenna LED 1 Bluetooth LED: Blue Flashing: pairing / USB connection Main Component CSR-BC02 External Flash ROM Size 8Mbits Power DC + 5V (from upstream USB port) Support Over current protection Housing Plastic (PC) Temperature Storage: -20 oC ~ 60oC Operation: 0 oC ~ 50oCRadio FrequencyOperating Temperature 0°C ~ 70°CChannel Frequency For USA, Canada, Japan: Frequencies: 2.400 – 2.4835 GHz, 79 channels For France: Outdoor use limited to 10 mW within the band, Frequencies: 2.454 – 2.4835 GHz, 23 channels For Italy: If used outside of own premises, general authorization is required Spread Spectrum Frequency Hopping Hopping Sequence 10 Types Hopping Rate 1600 hops/s (Nominal) 3200 hops/s (Page State) Maximum Input Level -5 dBm
User’s Guide3Output Power Class Class II Output Power Level 0~6 dBm (Max.) Transmit Central Frequency Tol erance <= 5KHz Sensitivity ≤ -82 dBm @ BER ≤ 0.1% Indoor Coverage Up to 10 meters Outdoor Coverage Up to 30 meters Throughput Asymmetric: 721 Kbps for one way and 57.6 Kbps in another way Symmetric: 432.6 Kbps in both direction Modulation Scheme GFSK with BT = 0.5 Physical Links Support ACL/SCO Links Network Capability Support Piconet Point-to-Point connection Piconet Point-to-Multipoint connection Scatternet connection Concurrent Connectivity Maximum 8 stations (in one piconet), 1 Server 7 Slaves Software3-Slot Packets Support 5-Slot Packets Support Slot Offset Support Timing Accuracy Support Switch Support Hold Mode Support Sniff Mode Support Test Mode Support Park Mode Support RSSI Support Power Control Support Authentication Support (Based on 8-Round SAFER+ Encryption Scheme) Link Manager Encryption Support (Using 4-LFSR with 8 and 128 Effective Key Length) Profiles Generic Access Profile Support
4MS-6871 Bluetooth USB HubService Discovery Profile Support Serial Port Profile Support Dial-Up Networking Profile Support Fax Profile Support LAN Access Profile Support Generic Object Exchange Profile Support File Transfer Profile Support Object Push Profile Support Synchronization Profile Support Personal Area Network Profile Support Hard Cable Replacement Profile Support Human Interface Device Profile Support Audio Gateway Profile Support Headset Profile Support Windows 98 Support Windows 98 SE Support Windows ME Support Windows 2000 Professional Edition Support Windows XP Professional Edition Support Host Systems Windows XP Home Edition Support
User’s Guide52. Installation2.1 Package CheckupUnpack the package and inspect all of the items carefully. If any of the itemsis damaged or missing, please contact your local dealer as soon as possible.Also, keep the box and packing materials at hand, in case you need to ship theunit in the future.2.2 Software Installation1. Insert the supplied CD disk into the CD-ROM drive.2. The CD will auto-run and the setup screen will appear.3. Click on Bluetooth Software and follow the on-screen instructionsto complete the installation.4. After completion of the installation, please restart your computer.SoftwareCDUser’sGuideBluetooth USB Hub
6MS-6871 Bluetooth USB Hub2.3 Hardware InstallationConnect the Bluetooth USB Hub to any available USB ports on thetarget devices with which you wish to establish wireless Bluetoothconnection. The target devices can be a desktop PC, a laptop PC, orany other types of PCs with Windows® OS & USB ports.After installation, make sure the Bluetooth USB Hub is placed ata location free from signal obstruction. Concrete walls, metalsubstances, paints with metal composites,... etc. will cause signalobstruction and disable the Bluetooth function.MSI Reminds You...To make sure that the hard-ware & software have beensuccessfully installed, go toControl Panel after restart-ing your system. Double-clickSystem and click the DeviceManager tab. If the hardware& software installation iscomplete, the MSI BluetoothDevice should appear.
User’s Guide73. Software Operations3.1 Introduction to BlueSoleil™BlueSoleil is a Windows-based software from IVT that allowsyour Bluetooth® enabled desktop or notebook computer towirelessly connect to other Bluetooth enabled devices.BlueSoleil allows MS Windows users to wirelessly access awide variety of Bluetooth enabled digital devices, such ascameras, mobile phones, headsets, printers, and GPSreceivers. You can also form networks and exchange datawith other Bluetooth enabled computers or PDAs.Platforms supported by BlueSoleil include: Windows 98SE,ME, 2000, and XP.1. Bluetooth FunctionsIn order to connect and share services via Bluetooth wirelesstechnology, two devices must support the same BluetoothProfile(s) as well as opposite device roles (i.e., one must bethe server, and the other must be the client). Bluetoothenabled devices often support multiple profiles, and if in-volved in multiple connections, can perform different de-vice roles simultaneously.BlueSoleil supports the following Bluetooth functions(Profiles) in the following device roles:
8MS-6871 Bluetooth USB HubNotes:1. Only one Headset or AV Headphone connection can existat a time, since since there is only one virtual Bluetoothaudio device.2. The Headset and AV Headphone Profiles do not work onWindows 98SE or Windows Me.2. Main WindowBy default, BlueSoleil starts with the Main Window open.Use the Main Window to perform your primary connection
User’s Guide9operations. The Main Window displays the local device (redball) as well as the remote devices detected in range. Differ-ent icons distinguish different types of remote devices.At the top of the Main Window are Service Buttons. Afteryou search for the services supported by a remote device, thesupported services of the selected device will be highlightedLocal Device — Basic Operations:- Hover your mouse over the red ball to display the local device’s Bluetooth name and address.- Click on the red ball to start or stop searching for Bluetooth devices in range.- Right-click on the red ball to display a pop-up menu of related operations (e.g., General Inquiry, My Services, Security, etc.).Remote Devices — Icon Meanings- White — Idle. The normal state of the device.- Yellow—Selected. You have selected the device.- Green — Connected. The device is connected to your local device.Remote Devices — Operations- Single-click to select.- Double-click to search for the services supported by the device.- Right-click to display a pop-up menu of related operations (e.g., Refresh Devices, Pair Devices, Connect, etc.).Services — Icon Meanings- White — Idle. The normal state.- Yellow — Available. The service is available on the selected device.- Green — Connected. The service is active in a connection with the remote device.
10MS-6871 Bluetooth USB HubServices — Operations- Hover your mouse over the service icon to display the name of the service.- Single-click on the service icon to connect.- Right-click on the service icon to display a pop-up menu of related operations.3.2 Basic Operations1. Insert AdapterBlueSoleil supports Windows systems enabled with Bluetoothwireless technology via either a USB adapter or aCompactFlash (CF) card.IMPORTANT! Be sure to insert the Bluetooth adapterBEFORE you install the software!USB Adapter:1. Insert the USB adapter into the USB port of your computer.CompactFlash Card:1. Insert the CompactFlash card into your computer. To usea CF card in a PC Card (PCMCIA) slot, first plug the cardinto a CF-to-PC Card adapter.2. The Found New Hardware Wizard will automatically start.Make sure the installation CD is still in your computer. Fol-low the wizard to install the card drivers.
User’s Guide112. Install the SoftwareIMPORTANT! If you have any Bluetooth software pre-viously installed on your computer, you must com-pletely remove it first!1. Insert the BlueSoleil software installation CD into the CDdrive of your computer.2. Use My Computer or Windows Explorer to access yourCD drive. In the CD, click on SETUP.EXE.3. Follow the directions on your screen to install the software.4. As prompted, when software installation is complete, re-start your computer.3. Start BlueSoleil1. Start BlueSoleil. Click on the BlueSoleil icon on yourdesktop, or go to Start | Programs | IVT BlueSoleil | BlueSoleil.Note: BlueSoleil will detect each insertion or removal of theUSB adapter. Alternatively, you can start BlueSoleil beforeplugging in the USB adapter.2.The very first time you use BlueSoleil, the Welcome toBluetooth screen will appear. Assign your Windows system aname and device type, to be shown to other Bluetooth en-abled devices. In most cases, you should leave the securitysetting checked. Click OK.
12MS-6871 Bluetooth USB Hub4. Search for Other Bluetooth Enabled DevicesBefore it can connect, your computer must first detect otherBluetooth enabled devices in range.Initiate a Device Search1. Make sure that the Bluetooth enabled device you wish toconnect to is turned on, with sufficient battery power, andset in discoverable mode. Have any necessary passkeys ready.If necessary, you may also need to enable the service youwant to use on the remote device. Refer to the remote device’suser documentation for instructions.If you haven’t done so already, you may also want to assignthe device a Bluetooth name. Refer to the device’s user docu-mentation for instructions.2. In the Main Window, click on the red ball to start thedevice search. Alternatively, you can click My Bluetooth |My Device Inquiry or View | Refresh Devices or press F5.3. After a few seconds, an icon will appear around the centerball for each Bluetooth enabled device detected within theradio range.Note:- The Main Window can display only eight discovered de vices at a time. If BlueSoleil discovered more than eight devices, use the scroll bar to view the remaining devices discovered by BlueSoleil.- To sort the devices by device name, device address, or device type, click View | Arrange Devices.4. Wait several seconds until BlueSoleil reports the name of
User’s Guide13each device.5. If the device you want is not listed, make sure that thedevice is turned on and discoverable and try searching again.You have multiple options for starting another search:- If you start another search by double-clicking on the red ball or clicking My Bluetooth | My Device Inquiry or View | Refresh Devices, then the list of previously detected de vices will not be cleared.- If you start another search by pressing F5, then the list of previously detected devices will be cleared.5. Establish ConnectionNote: These are generic instructions for any type of Bluetoothenabled device. Refer to the instructions in Chapter 3 forspecific details for the type of service you plan to use.Normally, a connection is initiated from the client. Checkthe chart in Chapter 1 to verify which device role BlueSoleilsupports for the service you wish to use.- On the server side, start the service- On the client side, initiate the connectionStart the ServiceIf you would like to use your computer as a server in aBluetooth connection, you must first start (enable) the ap-propriate service(s) on your system.1. Access the Service Window. Click View | Service Window.2. If the icon for a service is highlighted (yellow), then theservice has already been started. If the icon is white, thenyou need to start the service in order to use it. Right-click
14MS-6871 Bluetooth USB Hubthe icon. In the pop-up menu, select Start Service. The iconshould now be highlighted (yellow). Serial Port icons will alsoreport which COM port is assigned to them.Note:- Icons will appear only for Bluetooth functions (Profiles) which BlueSoleil supports in the Server device role. See chart in the 1.1 Bluetooth Functions.- Depending on your system, multiple icons for Serial COM ports may appear.3. After you have started the service in BlueSoleil, now youare ready to initiate the connection from the remote device.For instructions, refer to the user documentation for theremote device.Initiate the ConnectionIf you would like to use your computer as a client in a Bluetoothconnection, make sure that you have started (enabled) theservice on the remote device. Otherwise, BlueSoleil will notbe able to discover the service and connect to it. Forinstructions, refer to the device’s user documentation.1. Return to the Main Window. Click View | Main Window.2. Double-click on the icon for the device you wish to con-nect to. BlueSoleil will begin to search for information aboutwhich services the device supports.3. After the search, icons will be highlighted (yellow) at thetop of the BlueSoleil Main Window for services that aresupported by the device. Verify that the service you want touse is supported.4. Right-click on the device icon. In the pop-up menu, clickConnect, then select the service. BlueSoleil will start the
User’s Guide15connection. Depending on the security settings of each device,you may need to enter the same passkey on each device inorder to bond the two devices.5. A screen may appear asking if you want to set up auto-matic connections. Click Yes or No.6. If you are connecting to a phone, your phone may ask ifyou want to ask the BlueSoleil computer to your device list.Enter Yes and enter a passkey.7. When the devices have successfully connected, the deviceicon in the Main Window will turn green, and a green line willappear between the red ball and the device icon. A red dot willtravel along the green line from the client to the server. Asignal strength icon will also appear next to the device icon.The BlueSoleil icon in the task tray will also turn green toindicate an active connection.Note: A red check mark will appear next to the name of anydevice that you have previously paired with your computer.8. Depending on which services you are using, additionalscreens may appear, and/or you may need to configure addi-tional connection settings (e.g., user name, password, COMport number, etc.). Refer to the instructions in Chapter 3 foryour specific service. After configuring the appropriate con-nection settings, you should be ready to use your application.9. To end a connection, in the Main Window, right-click onthe icon for a connected device. In the pop-up menu, clickDisconnect.Note: You can only disconnect this way if your computer isacting as a client device. If your computer is acting as aserver device, then you can disconnect in BlueSoleil by click-
16MS-6871 Bluetooth USB Hubing View | Service Window, then right-clicking on the serviceicon. In the pop-up menu, click Stop Service. Alternatively,you can disconnect from the remote device.6. Bluetooth SecurityTo modify your connection’s security settings, click MyBluetooth | Security.BlueSoleil offers three security levels:- Low (Security Mode 1, Non-secure) No security procedure is needed for connections.- Medium (Security Mode 2, Service level enforced security) Authentication or Authorization is requested when a spe cific service is accessed by other Bluetooth enabled devices. If two devices are connecting for the first time, or if two devices do not have a trusted relationship, then the same passkey must be provided on both sides to complete the Authentication. This mode allows you to assign different access rights for each service supported by the server device.- High (Security Mode 3, Link level enforced security) If either of two devices is in Mode 3, Authentication is requested whenever a link connection is initiated between two Bluetooth enabled devices. The passkey must be pro vided on both sides to complete Authentication.Note: In Security Mode 2, the user can add each authenti-cated device into a trusted device list to expedite futureconnections.
User’s Guide173.3 Getting Started1. AV HeadphoneThe AV Headphone Profile enables use of a Bluetooth en-abled headphone to listen to high-quality stereo music playedon a computer.Typical Usage- Listen to music using a Bluetooth enabled AV headphone.Step 1: Connect to the AV headphone.Step 2: Play music using media player software on yourcomputer. Music will transmit wirelessly to the headphone.2. Basic ImagingThe Basic Imaging Profile (BIP) enables users to receivepictures from a Bluetooth enabled digital camera, mobilephone, or other compatible device. It also enables remotecontrol of shooting, display, and other imaging functions.Typical Usage- Control camera to take pictures- Receive pictures sent from BIP-enabled digital devicesControl Camera to Take PicturesStep 1:Connect to the camera. A Bluetooth Camera Con-troller will appear.Step 2: Click the button to capture the image. The capturedimage will be transmitted to your computer and displayed.
18MS-6871 Bluetooth USB HubStep 1: Assign the directory where you would like to saveimage files pushed from the client device. Click My Services| Properties. Click on the Basic Image Push tab. In the Setthe image directory field, browse to select the file location.Click OK.Step 2: Start the BIP service.Step 3: Send pictures from the remote device. For instructions,refer to the user documentation for the remote device.3. Dial-up NetworkingThe Bluetooth Dial-up Networking (DUN) Profile enablesusers to wirelessly dial-up to the Internet through a Bluetoothenabled modem or mobile phone that supports the DUNProfile.Typical Usage- Dial-up to the Internet via a Bluetooth enabled mobile phone.- Dial-up to the Internet via a Bluetooth enabled modem.Dial-up to the Internet via a Bluetooth enabled mobile phone.Step 1: Connect to the phone’s Dial-Up Networking Service.Step 2: The Dial-Up Dialog will appear. Enter the dial-upnumber, User name, and Password. Make sure the correctdial-up number is entered, then click on the Dial button.Note: The default dial-up number *99***1# only workswith certain GPRS phones and service providers in the UnitedStates. If necessary, enter the correct dial-up number foryour Internet Service Provider (ISP).
User’s Guide19Note: After you successfully connect, a screen will ask if youwould like to create a dial-up shortcut on your desktop. Thiswould allow you to conveniently dial up and connect bysimply clicking on the shortcut, without having to manuallystart BlueSoleil. Alternatively, after starting BlueSoleil, youcan start the shortcut by clicking Tools | My Shortcuts.Dial-up to the Internet via a Bluetooth enabled modem.Step 1: Connect to the modem’s Dial-Up Networking Service.Step 2: The Dial-Up Dialog will appear. Enter the dial-upnumber, User name, and Password. Enter the correct dial-upnumber, then click on the Dial button.Note: The default dial-up number *99***1# does NOT workwith modems. You need to enter the correct dial-up numberfor your Internet Service Provider (ISP).Step 3: Use your email, Internet browsing or other applica-tion that utilizes a dial-up connection.Note: After you successfully connect, a screen will ask if youwould like to create a dial-up shortcut on your desktop. Thiswould allow you to conveniently dial up and connect bysimply clicking on the shortcut, without having to manuallystart BlueSoleil.4. FAXThe Bluetooth Fax Profile enables users to send faxes froma computer via a Bluetooth enabled mobile phone or modem.
20MS-6871 Bluetooth USB HubTypical Usage- Send fax via a Bluetooth enabled mobile phone.- Send Fax via a Bluetooth enabled modem.Send fax via a Bluetooth enabled mobile phoneStep 1: Connect to the mobile phone’s fax service.Step 2: Use your fax software to send the message.Send fax via a Bluetooth enabled modemStep 1: Connect to the modem’s fax service.Step 2: Start your fax software. Configure your fax softwarefor the Bluelet Fax Modem (NOT the Bluelet Modem). Re-fer to your fax software’s user documentation for instructions.Step 3: Use your fax software to send the message.5. File TransferThe File Transfer Profile (FTP) enables users to transferfiles and/or folders between Bluetooth enabled laptops,desktops, PDAs, mobile phones, etc.Typical Usage- Connect to a Bluetooth enabled mobile phone and transfer files or folders to/from the phone.- Share a folder on your computer with other Bluetooth enabled devices.- Access a shared folder on another Bluetooth enabled device. Connect to a Mobile PhoneStep 1: Connect to the mobile phone’s FTP service.Step 2: The phone’s folders are shown in a window. Users cancopy/paste/delete files or folders.
User’s Guide21Share a Folder on Your Computer with other Bluetooth En-abled DevicesStep 1: Select the folder you would like to use for file sharingand define the remote user privileges.Click My Services | Properties. Click on the File Transfertab.Share this folder: Browse to select the folder you would liketo share.Share Permissions: Select Read and Write to allow others tocopy, paste or delete files/folders in this folder. Select ReadOnly to allow others to only browse and copy files/foldersfrom this folder.Step 2: Start the FTP service in BlueSoleil. Do not initiatethe connection in BlueSoleil.Step 3: Browse your computer from the remote device. Forinstructions, refer to the user documentation for the remotedevice. When the remote device attempts to connect toyour computer, the Bluetooth Service Authorization screenmay appear. Click Yes.Step 4: After successfully connecting, the remote device canbrowse, copy, paste, and/or delete files on your computer,depending on the remote folder privileges you allowed. Forinstructions, refer to the user documentation for the remotedevice.Access a Shared Folder on Another Bluetooth Enabled Device.Step 1:On the remote device, designate the folder/files toshare. Enable file sharing on the remote device. Forinstructions, refer to the user documentation for the remotedevice.
22MS-6871 Bluetooth USB HubNote: If you do not enable file sharing on the remote device,BlueSoleil will not be able to discover the device’s file sharingservice.Step 2: Start the FTP service and initiate the connection inBlueSoleil.Step 3: A Remote Shared Folder screen will appear, display-ing shared files/folders on the remote device, Use the screento browse, copy, paste, and/or delete files, depending on yourfolder privileges.6. HeadsetThe Headset Profile enables users to use a Bluetooth enabledheadset as wireless earplug or microphone.Typical Usage- Use Headset as a device for audio input/output.Step 1: Connect to the Bluetooth enabled headset.Step 2: Play music on your computer, or chat using networkmeeting tools. You may need to press a multifunction buttonon your headset to transmit audio between the computer andthe headset.Note: For most Bluetooth enabled headsets, after you havesuccessfully connected for the first time, you can quicklyreconnect to BlueSoleil by simply pressing a multifunctionbutton on the headset.
User’s Guide237. Human Interface DeviceThe Bluetooth Human Interface Device (HID) Profile en-ables users to use Bluetooth enabled HID Devices such askeyboards, mice or joysticks to control your computer.Typical Usage- Connect a Bluetooth enabled Mouse and a Keyboard to Your ComputerStep 1: Connect the Bluetooth enabled mouse to yourcomputer.Step 2: Connect the Bluetooth enabled keyboard to yourcomputer, following the instructions in Chapter 2. Beforeyou can use BlueSoleil to connect, you may need to press abutton on the keyboard to make it discoverable.Note:- The first time you connect the mouse or keyboard to your computer, the Found New Hardware Wizard will automati cally launch. In the first screen of the wizard, DO NOT INSERT ANY CD and click Next. Follow the next screens until you complete the wizard. If the wizard reappears, cancel the wizard. You should be able to use the mouse or keyboard with your computer.- The Bluetooth enabled mouse/keyboard can automatically re-connect to your computer after you successfully estab lish the initial connection.
24MS-6871 Bluetooth USB Hub8. LAN AccessThe Bluetooth LAN Access Profile (LAP) allows users toaccess a Local Area Network (LAN) via a Bluetooth enabledLAN access point.Typical Usage- Access a Local Area Network via a Bluetooth enabled LAN access point- Use your computer as a LAN Access PointAccess a LAN via a Bluetooth enabled Access Point (AP)Step 1: Connect to the LAN AP’s LAP service.Step 2: In the Connect Bluetooth LAP Connection dialog,enter the user name and password if necessary. Click Connect.Use your computer as a LAN Access Point (ADVANCEDUSERS ONLY)Step 1: Start the Bluetooth LAN Access service on BlueSoleil.Step 2:Specify any static IP addresses necessary for LAPclients. (Alternatively, you can use DHCP to have the sys-tem dynamically assign IP addresses).(1) In the Network Connections window, right-click In-coming Connection, then select Properties.(2) Select Incoming Connections Properties | Networking-> Internet Protocol (TCP/IP), and click on the Propertiesbutton.(3) Select Specify TCP/IP addresses and enter the range ofIP addresses assigned to LAP clients.
User’s Guide25Note:In order to use a Windows 98SE/Me system as an accesspoint, you must have already installed a Dial-up Adapter andthe Windows Direct Cable Connection component on thesystem.9. Object PushThe Bluetooth Object Push Profile (OPP) enables users tosend and receive Personal Information Management (PIM)data objects (including messages, notes, calendar items, andbusiness cards) to and from a Bluetooth enabled PDA ormobile phone.The objects supported include:- Contacts (*.vcf)- Calendar items (*.vcs)- Notes (*.vnt)- Messages (*.vmg)Typical Usage- Push objects to a Bluetooth enabled mobile phone or PDA.- Receive objects from a Bluetooth enabled mobile phone or PDA.Note: If you would like to push PIM objects to a PDA, makesure that the PDA is ready to receive a PIM object beforeyou start. If necessary, enable Object Push on the PDA. Forinstructions, refer the PDA’s user documentation.Push Objects to a Bluetooth Enabled Mobile PhoneThere are two methods to push objects:
26MS-6871 Bluetooth USB HubMethod 1: From BlueSoleil Main Window: Double-click onthe mobile phone or PDA icon to browse for serviceinformation. The Object Push Service icon should be high-lighted at the top of the screen. Right click the Object PushService icon, and in the pop-up menu click Send My Card.Send My Card: Send your default business card.Get Card: Get the phone’s default business card.Send Objects: Select objects (PIM files ending in .vcf, .vcs, .vnt, or .vmg) and send them to the phone.Exchange cards: Have your computer and the phone to ex-change their default business cards.Method 2: From MS Outlook:(1) Select the contact that you would like to send.(2) In Outlook, click on the Push button on the toolbar, orclick File | Push.(3) The Bluetooth Neighbors screen will appear. In the de-vice list, select the phone or PDA that you wish to push thecontact to. Click on the Push button.Receive Objects from a Bluetooth Enabled Mobile PhoneStep 1: Configure the parameters for the object push. Fromthe Main Window, click My Services | Properties. Click onthe Object Push tab.Step 2: Start the Object Push service. Do not initiate aconnection, only start the service so that your computer willbe ready to receive objects.Step 3: Send objects from the phone. For instructions, referto your phone’s user documentation.
User’s Guide27Notes:- BlueSoleil creates a Bluetooth folder (with Inbox and Outbox subfolders) in your My Documents folder for use with Ob- ject Push. The Inbox is used to save objects received from other devices. The Outbox is used to save objects sent out from your computer.- Your can set your default business card by clicking My Services | Object Push. In the Send My Business Card field, browse to select a contact as your default business card.10. Personal Area NetworkingThe Bluetooth Personal Area Networking (PAN) Profileenables PCs, laptops, PDAs, and other Bluetooth enableddevices to form either of two kinds of PAN networks. In aGroup ad-hoc Network (GN), which functions as an isolatednetwork, multiple PAN Users (PANUs) are linked togethervia a GN controller. Alternatively, a PAN can consist ofmultiple PANUs linked to a Network Access Point (NAP),which provides access to external Local Area Network (LAN)infrastructure. BlueSoleil supports all three of these deviceroles — GN (controller), PANU, and NAP.Typical Usage- Group Ad-hoc Network (Peer-to-peer networking) One device acts as the GN, and others function as PANU devices. These computers can visit each other or use an application based on TCP/IP.- Access a LAN via a Network Access Point (or a Computer Acting as a NAP) After the computers connect to the NAP, they become members of the LAN and can directly com- municate with other computers in the LAN.
28MS-6871 Bluetooth USB HubConnecting the PAN User (PANU)Step 1: Connect to the server’s Personal Area Network service.Step 2: Wait a few seconds for BlueSoleil to obtain and dis-play your computer’s IP address.Configuring the NAP/GNClick Bluetooth Service | Properties and click on the Per-sonal Area Network tab.Scenario 1 Group Ad-hoc NetworkSelect Set up Bluetooth Personal Area Network and EnableDHCP Server.A DHCP server will be started on the GN. The PANU canobtain an IP address automatically from this DHCP server ifthe PANU does not set static IP address for the BT NetworkAdapter.Scenario 2 Access LAN via PAN-NAPSelect Access LAN Network and select a physical networkadapter, through which the NAP connects to a LAN, as theLAN Adapter.Scenario 3 Access the Internet via NAPSelect Access Internet and select a physical network adapter,through which the NAP connects to Internet, as the WANAdapter. It will automatically enables NAT (Network Ad-dress Translation, please refer to Windows Help Topic) func-tion and a DHCP server.Note: The BT Network Adapter on the PANU side must beset to obtain an IP address automatically. The IP address is inthe form of 192.168.2.xxx, such as 192.168.2.1.
User’s Guide2911. PrinterThe Bluetooth Printer Profile (HCRP) enables your com-puter to connect to a Bluetooth enabled printer.Typical Usage- Print documents on a Bluetooth enabled Printer.Step 1: Connect to the printer’s printer service.(a) If your computer does not have the correct printer driv-ers installed, BlueSoleil will prompt you to do so.Install the driver for the printer, and remember to set theprinter port to the correct COM port number. To determinethe correct COM port number, in the Main Window, right-click on the device icon. In the pop-up menu, select Status.(b) If the printer driver has been installed, a message indi-cates that the printer is ready.Step 2: Print documents using the Bluetooth enabled printer.In the application, be sure to select the correct printer andprinter port.12. Serial PortThe Bluetooth Serial Port Profile (SPP) provides PCs,laptops, PDAs, GPS receivers, cordless serial adapters, andother Bluetooth enabled devices with a virtual serial port,enabling them to connect with each other wirelessly viaBluetooth instead of with a serial cable.BlueSoleil supports four Bluetooth Serial Ports for outgoingconnections and two Bluetooth Serial Ports for incomingconnections.
30MS-6871 Bluetooth USB HubTypical Usage- Connect to other Bluetooth enabled devices via the Serial Port.Connect to a PDAStep 1: Connect to the PDA’s Serial Port service.Step 2: Use ActiveSync or any other application that uses aserial connection.Note:- Serial Port Auto-Connection function. Once a target de vice is assigned to a specific serial port, (e.g., COM5), when- ever an application opens that serial port number, BlueSoleil will automatically connect to the target device. Similarly, whenever an application closes the Bluetooth serial port, BlueSoleil will stop the connection. To check which de vices are assigned to which COM ports, click Tools | Con figurations | Connect With.- Some applications only allow you to use a limited range of COM port numbers. If the application does not allow you to use a COM port number assigned by BlueSoleil, you will not be able to use BlueSoleil with your application.13. Bluetooth SynchronizationThe Bluetooth Synchronization (SYNC) Profile enables us-ers to synchronize PIM objects on their computer with thatof other Bluetooth enabled computers as well as Bluetoothenabled mobile phones, PDAs, and other devices.Four kinds of objects are supported:- Contacts (*.vcf)
User’s Guide31- Calendars (*.vcs)- Notes (*.vnt)- Messages (*.vmg)Supported MS Outlook versions: Outlook 2000, Outlook2002 (xp), Outlook 2003.Typical Usage- Synchronize your computer with a Bluetooth enabled mo- bile phoneStep 1: Connect to the mobile phone’s Synchronizationservice.Step 2: A synchronization dialog will appear. Click on theStart button to synchronize. Contacts, calendars, notes andemails in MS Outlook will be synchronized with those on thephone.Note:- Users can start synchronization from MS Outlook using the Bluetooth Add-In menus and buttons installed with BlueSoleil.- BlueSoleil can act as synchronization server. Click My Services | Properties. Click on the Information Synchroni zation tab, and select the type of PIM objects that you would like to synchronize.
32MS-6871 Bluetooth USB Hub3.4 BlueSoleil User Guides1. BlueSoleil Environment1.1 Main WindowThe Main Window displays the local device (red ball) and theremote devices detected in range. Connecting and discon-necting operations are conducted here. Connections are in-dicated by green dashed lines between the local device andconnected remote devices.By default BlueSoleil starts with the Main Window open. Toreturn to the Main Windows after switching views, clickView | Main Window.The Local Bluetooth enabled device, known as “My Device”,represents the user’s computer that is running BlueSoleil.Operations- Hover your mouse over the red ball to display the local device’s Bluetooth name and address.- Click on the red ball to start or stop searching for Bluetooth devices in range.- Right-click on the red ball to display a pop-up menu of related operations (e.g., General Inquiry, My Services, Security, etc.).Remote Bluetooth DevicesRemote devices are other Bluetooth enabled devices that arein the radio range of your local device. BlueSoleil uses differ-ent icons to indicated different types of remote devices.
User’s Guide33Icon MeaningsThere are 3 states for the service icons, indicated by differ-ent colors.- White — Idle. The normal state.- Yellow — Available. The Bluetooth service is available on the selected remote device.- Green — Connected. The Bluetooth service is active in a connection with the remote device.Operations- Hover your mouse over the service icon to display the name of the service.- Single-click on the service icon to connect.- Right-click on the service icon to display a pop-up menu of related operations.
34MS-6871 Bluetooth USB Hub1.2 Service WindowThe Service Window displays the local Bluetooth services,(i.e., the Bluetooth services supported by BlueSoleil). Usethe Service Window to start and stop services, as well as toconfigure service properties. To access the Service Window,click View | Service Window.Local Service ListThe Local Service List displays all of the Bluetooth servicessupported by the local computer. Use this screen to start/stop services.Icon MeaningsThere are 3 states for the local Bluetooth services, indicatedby different icon colors.- White – Idle. The service has not been started.- Yellow – Started. The local Bluetooth service has been started.- Green – Connected. Some remote device has connected to the service.Operations- Single-click on the icon to select the service.
User’s Guide35- Double-click on the icon to Start/Stop a service.- Right-click to display a pop-up menu of related operations.1.3 MenusBlueSoleil contains the following six menus:- File Menu- View Menu- My Bluetooth Menu- My Services Menu- Tools Menu- Help MenuFile MenuHide — Hide the BlueSoleil window. Connections can stillrun when the window is hidden.Always on Top — Keep the BlueSoleil window always ontop.Exit — Exit BlueSoleil.You can also exit BlueSoleil by right-clicking on the tasktray icon at the bottom of your screen. In the pop-up menu,click Exit.View MenuMain Window — Show the BlueSoleil Main Window.Service Window — Show the BlueSoleil Service Window.Arrange Devices — Arrange remote devices by Device Name,Device Address, or Device Type.Refresh Devices — Refresh the list of remote devices de-tected by BlueSoleil.
36MS-6871 Bluetooth USB HubNote: If you select Refresh Devices, the list of previouslydetected devices will not be cleared. To initiate a new devicesearch that will first clear the list, press F5.My Bluetooth MenuBluetooth Device Inquiry — Search for other Bluetooth en-abled devices in range.Bluetooth Service Browsing — Browse for the services ofthe selected remote device.Security — Configure the security settings of the local de-vice (e.g., passkey requirements, data encryption, etc.).Properties — Configure the properties of the local device (e.g., device name, accessibility, etc.).My Services MenuStart Service — Start the selected local Bluetooth service.Stop Service — Stop the selected local Bluetooth service.Status — View the status of the selected local Bluetoothservice.Properties — Configure the properties of the local Bluetoothservices (e.g., automatic connections, shared file locations,etc.).Tools MenuMy Shortcuts — Display dialog Bluetooth Shortcuts.Connect: Connect the selected shortcut.Delete: Delete the selected shortcut.Find Device — Click to find a device, by either of two searchcriteria:
User’s Guide37By Bluetooth Device Address:Enter a Bluetooth device address, in standard format (xx:xx:xx:xx:xx:xx), and click on the Find button. The device withthe specified address will appear highlighted in the MainWindow.By Name:Check the By Name box, enter the Name of the device, andclick on the Find button. The device with the specified namewill appear highlighted in the Main Window.Add New Device — Add a remote device by entering itsBluetooth device address.Add Device From History — Add a remote device from thehistory list.Add: Add the selected device.Delete: Clear the selected device from the historylist.Configurations->Connect With — If desired, assign a re-mote device to automatically connect with a Bluetooth se-rial port whenever an application opens the specified port.Assign: Assign a device to the selected port.Remove: Remove the Auto-Connection device assignment for the selected port.Configurations-> Unplug HID — Remove Human InterfaceDevices from BlueSoleil.Unplug: Unplug the selected HID device.When you first connect the HID device to your computer,BlueSoleil sets up the devices so that they will automaticallyreconnect in case the connection is ever broken. After youunplug an HID device, it will no longer automatically recon-nect to your computer.
38MS-6871 Bluetooth USB HubBluetooth Device — Advanced hardware configuration, rec-ommended for advanced users only. Please refer to 4.2 Hard-ware Configuration for more details.Help MenuContents and Index — Access BlueSoleil Online Help.About BlueSoleil — Information about your version ofBlueSoleil.2. Device Configurations2.1 Hardware ConfigurationBlueSoleil supports the following kinds of Bluetooth radioadapters: USB and CF card.To access the hardware configuration screens, click Tools |Bluetooth Device…,Bluetooth DeviceSelect the type of Bluetooth enabled device that you plan touse, either a USB adapter or a CompactFlash (CF) card.Advanced ConfigurationThe Advanced Configuration page will be enabled only if youselected CF in the Bluetooth Device screen. Use the Ad-vanced Configuration screen to configure detailed param-eters including COM Port, Baud Rate, Byte Size, Parity, StopBits, and Flow Control.
User’s Guide392.2 Properties ConfigurationTo configure the properties of your local device, click MyBluetooth | Properties…,GeneralDevice NameThe local device’s name, which will be shown to otherBluetooth enabled devices.Device TypeThe device type of your local computer, (i.e., Desktop,Laptop or Server).Device AddressThe address of the local device. Every Bluetooth enableddevice has a unique device.AccessibilityConnecting Mode- Connectable: Permits other Bluetooth enabled devices to connect with your computer.- Non-Connectable: Prohibits other Bluetooth enabled de vices from connecting with your computer.Discovery Mode- General Discoverable: Permits other Bluetooth enabled de vices to detect your computer.- Limited Discoverable: Permits other Bluetooth enabled devices to detect your computer with Limited Inquiry.- Non-Discoverable: Prohibits other Bluetooth enabled de vices from detecting your computer.
40MS-6871 Bluetooth USB HubBonding Mode (Pairing Mode)- Accepts Bonding: Allow other Bluetooth enabled devices to pair with your computer. If the other device initiates a pairing procedure with your computer, each device must enter the same passkey before the they will be paired.- Does Not Accept Bonding: Rejects pairing attempts initi ated by other Bluetooth enabled devices.HardwareView information about your Bluetooth hardware.- Manufacturer: The manufacturer of the local Bluetooth device.- HCI Version: The HCI version of the local Bluetooth device.- HCI Edition: The HCI edition of the local Bluetooth device.- LMP Version: The LMP version of the local Bluetooth device.- LMP Subversion: The LMP subversion of the local Bluetooth device.3. Security ConfigurationUse the Security Configuration screens to specify the secu-rity settings of your local device.3.1 Pair / Un-pair DevicesOnce a remote device has paired with your computer byexchanging passkeys, passkeys will no longer be required forfurther connections between your computer and the device.
User’s Guide41How to pair with another deviceAutomaticallyIf a passkey is required for connection, the devices will bepaired automatically the first time they successfully exchangepasskeys and connect. After a device has successfully pairedwith your computer, the remote device icon in the MainWindow will have a red checkmark next to it.ManuallyIn the Main Window, right click on the device icon, and inthe pop-up menu, select Pair Device. In the Enter BluetoothPasskey screen, enter the same passkey that you enter onthe remote device. After a device has successfully paired withyour computer, the remote device icon will have a redcheckmark next to it.How to un-pair with another deviceIn the Main Window, right-click on the device icon, and inthe pop-up menu, select Unpair. The red checkmark next tothe device icon will disappear.3.2 General SecurityTo access the security configuration screen, click MyBluetooth | Security…Security LevelLowIf checked, other devices will be able to access your devicefreely without entering a passkey. However, if the remotedevice requires a passkey to connect, then both devices needto exchange passkeys.
42MS-6871 Bluetooth USB HubMediumThe medium level provides service level security. You canassign the appropriate level of access for each specific service.For more details, see 4.3.4 Local Services Security.HighIf checked, passkeys must be exchanged for every incomingand outgoing connection, unless the two devices have al-ready paired in the past.Bluetooth PasskeySet Default PasskeyUse this setting to create a default passkey for all connections.This saves you the effort of manually creating a passkeywhenever one is required.Data EncryptionEnable Data EncryptionIf checked, the data transmitted will be encrypted.3.3 Managing Device PairingsTo access the device security configuration screen, click MyBluetooth | Security and click on the Devices tab.Paired DevicesThis screen lists devices which have already paired with thelocal device.Remove PairingClick to remove the pairing relationship between the se-lected device and the local device.
User’s Guide43AuthorizationClick to select the local Bluetooth services that you wish toallow the selected paired device to use. A list of local serviceswill appear. Select the services you wish to allow on theremote device, then click OK.Note:The screen will only list the local services that requireauthentication. The local services that do not require au-thentication can be accessed freely. The Authorization but-ton is enabled only when the Security Level is set to Medium.3.4 Local Services SecurityTo access the local services security configuration screen,click My Bluetooth | Security and click on the Services tab.You can only configure security for local services when theSecurity Level is set to Medium. (Set the Security Level inthe General Security screen.)Local Services:AuthenticationIf checked, a passkey is required whenever a remote deviceattempts to connect with this service.EncryptionIf checked, data transmitted between devices for this servicewill be encrypted.Click to select the devices you wish to allow to use theselected service.
44MS-6871 Bluetooth USB HubIn the Service Authorization screen, enter the followingsettings:Trusted DevicesSelect to trust devices listed in this screen to use the selectedservice on your device. A device can freely access the servicefrom your local device when trusted. Click Add/Remove toedit the device list.Trust all devicesConnection requests will be accepted from every device.Prompt user if the device is not trusted for this serviceIf a non-trusted device attempts to access the service, adialog will appear to allow you to accept or reject theconnection.Reject devices from using the service if not trusted for theserviceIf a non-trusted device attempts to access the service, theconnection will be rejected automatically without informingthe user.Notes:If a device is trusted for a service, it may connect to thisservice on your local device without informing you.
User’s Guide454. Technical SupportRefer to the following sources for additional information and forproduct and software updates.The MSI website (http://www.msi.com.tw/) provides updatedinformation on MSI Bluetooth hardware and software.For technical support, please email to support@msi.com.tw.
46MS-6871 Bluetooth USB HubNOTES
User’s Guide475. GlossaryBDABluetooth Device Address. Every Bluetooth device has a unique48-bit binary Bluetooth Device Address (BDA) burned into itsRead-Only Memory (ROM). This address cannot be changedby the end-user.A device’s BDA is usually displayed in hexadecimal format;00:D0:B7:03:2E:9F is a valid BDA.Each Bluetooth device also has an operator-configurable, user-friendly name to help distinguish it from other Bluetoothdevices. The user-friendly name may be up to 99 alphanumericcharacters in length and may contain spaces. My PersonalComputer is a valid user-friendly name.Device InquiryThe process of searching for other Bluetooth devices.DHCPDynamic Host Control Protocol-when enabled, connecting de-vices are assigned an Internet Protocol (IP) address by theserver.FTPFile Transfer ProtocolHCIHost Controller Interface
48MS-6871 Bluetooth USB HubIrDAInfrared Data AssociationIrMCInfrared Mobile CommunicationsLink KeyAn internally-generated unique security key that is exchangedby paired devices as proof of identity before a connection isestablished.LMPLink Manager Protocol—used by Bluetooth for internalcommunications.Page Scan ModeA Bluetooth mode in which a server is actively listening(scanning) for a client to “page” it. The server then answers thepage and attempts to set up a connection with the pagingdevice (the client).PasskeyAn alphanumeric string up to 16 characters in length. Passkeysare also called PIN codes, or Personal Identification Numbers.PiconetA network of devices connected in an ad hoc fashion usingBluetooth technology. A piconet is formed when at least two
User’s Guide49devices, such as a portable PC and a cellular phone, connect. Apiconet can support up to eight devices. When a piconet isformed, one device acts as the master while the others act asslaves for the duration of the piconet connection.PIMPersonal Information Manager—an application, such asMicrosoft Outlook, that is used to manage contacts, keep trackof phone numbers, etc.PINPersonal Identification Number, also referred to as a “pass-key” or “password.”ScatternetA group of independent and non-synchronized piconets thatshare at least one common Bluetooth device. Bluetooth devicesmust have point-to-multipoint capability to engage in scatternetcommunication. There may be a maximum of 10 fully loadedpiconets in a scatternet.Service DiscoveryThe process of determining the services that a Bluetooth serverprovides.SysTrayThe Windows system tray-usually located in the lower-rightcorner of the screen.

Navigation menu