Microboards Technology Pf 3 Users Manual PRF QRG 2.PMD

PF-3 to the manual 7eba5c9e-f4a4-4ca9-9873-56284862f4f3

: Microboards-Technology Microboards-Technology-Pf-3-Users-Manual-555885 microboards-technology-pf-3-users-manual-555885 microboards-technology pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

PF-3 Print Factory Installation
Quick Reference Guide
for Windows Vista, XP, or 2000
For a more in-depth look at the 4. After the physical hardware setup is complete, you will be instructed to connect
the PF-3 Print Factory to the computer. Once this occurs, Windows will find
installation process, please refer to
your new hardware and run through the driver installation process.
the Installation section of the User’s
5. Windows Vista: Drivers for Vista are pre-installed when the CX-1 Installer is
Manual.
Be sure your computer meets the
Minimum System Requirements as stated
in the User’s Manual and that you have
read these instructions and the Manual
prior to contacting Microboards Technical
Support with installation or configuration
questions!
Do NOT connect your PF-3 Print Factory to your
computer until you are prompted to do so by the PF-3
Print Factory Installer

PF-3 Print Factory Installation:
1. Unpack the PF-3 Print Factory and place it in the selected workspace. This
space should have enough vertical space to allow for easy loading of media into
the input hopper and have enough room behind the PF-3 Print Factory to allow
the unloading of rejected discs.
2. Insert the PF-3 Print Factory Installation disk into the CD/DVD ROM drive on
your computer. The installer should open automatically.

run. By pre-installing the drivers, your PC will install the hardware without
intervention once the USB connection is made.
Windows XP: Do not allow the
Search the Internet option to attempt
to find the drivers for you. Select
the option to Install from a list or
specific location and click Next.
Check the Search Removable Media
box and click Next.
Windows 2000: Select the option
to Search for a suitable driver, and
click Next. Check the CD-ROM
Drives Box and click Next. Click
the Next button again when you are
notified that the driver has been
found.

6. If the Microsoft Digital Signature screen appears, click the Yes or Continue
Anyway button at the bottom of the screen.

F.

Click Finish once the installation is complete. You will also have the
opportunity to register the software on-line.

10. The Microboards Printer Toolbox Installation
The Microboards Toolbox is installed silently during the PF-3 installation. This
application is used to monitor the PF-3 Print Factory and for general maintenance
functions.

After the installation completes, the Toolbox will start up. You will see an icon
appear in the tool tray in the lower right corner of your Windows desktop. To
access the Toolbox, double-click the icon circled below.
The Toolbox will also automatically start up after rebooting the PC.
The Installation disc can be used to just re-install the Toolbox, if necessary.
Place the CD in your PC’s CD/DVD ROM drive and select the option to reinstall.
You will have the option of reinstalling SureThing, the Toolbox, or both at once.

For more information on configuration options, please see the PF-3
Print Factory Configuration Quick Reference Guide on the other side
of this page, or refer to the appropriate sections of the User’s Manual.

7. Once the drivers for this component have been installed, you will be prompted to
install the ink cartridges. Click the Next button when complete.
8. Click the Finish button when complete.
Installation of SureThing CD Labeler will occur next.
9. SureThing CD Labeler Installation
A.
B.

Click the Next button at the Welcome screen.

C.

To install to the default
directory, click Next on the
Select Destination Directory
screen. If you wish to install to
a different location, select that
location before clicking Next.

D.

Select the option to add a
desktop shortcut and the
location in which the Start Menu
shortcut will be created, or make
no changes to select the default locations. Click Next when the locations
are suitable.

If the installer does not automatically open, click the Start button and select
Run from the Start menu. Click the Browse button and go to the CD/DVD drive,
highlight Setup.exe, click the Open button, then click OK.
Please follow all directions on each window before clicking the Next button.
3. You will first be guided through the hardware setup. Do not click the Next
button until you have completed each step.

Read the Software License and Warranty information and click the I Accept
button to continue the installation of SureThing.

E.

Installation Troubleshooting Guide:
Hardware not installing on
PC

1. Turn on power to PF-3 Print Factory (back panel)
2. Reseat USB connection
3. Installation CD in drive?

Printer not responding

1. Ink cartridge installed correctly?
2. Turn on power to Printer (front and rear panels).

In order to guarantee quality results from the PF-3 Print Factory,

ONLY V102C and V101B
INK CARTRIDGES CAN BE USED!
As is true with all printers, the quality of ink cartridge and the quality of the ink
within the cartridge will affect your output. To ensure quality results, the PF-3
Print Factory will not operate with any other ink cartridges in place.

Click Start on the next screen to install the application.

The use of refilled ink cartridges will void your warranty!
Please visit our Technical Support website at www.microboards.net

820-00229-01

PF-3 Print Factory Configuration
Quick Reference Guide
for Windows Vista, XP, or 2000

Print Image Diameter Settings

Print Image Alignment

Printer Toolbox

The Microboards PF-3 Print Factory includes the ability to mask the print image
diameters to ensure that your media is not being printed outside of the printable
surface. While SureThing Disc Labeling software creates circular templates 120mm
in diameter, other applications may not limit the design to the correct size.

Your PF-3 Print Factory has been factory aligned to .1mm precision. Fine tuning
may be required depending on the media brand and printable surface type you are
using to provide full surface coverage.

The Printer Toolbox contains
several utility functions for the
PF-3 Print Factory. The toolbox
will open automatically after
installation of the PF-3, and
each time the PC boots up. It
can also be run by doubleclicking the PF3 Toolbox icon
in the tool tray.

The default Inner Diameter setting is 360 (36mm). If you are using a print template
with an inner hub of less than 36mm, you must change the Inner Diameter setting
to match that of the template for the image to print correctly.

1. Access the Printing Preferences for the Microboards PF3. How this is done
will depend on the Operating System and the currently selected Start Menu
layout.

To change the Diameter settings, please follow these steps:

In Windows Vista, select the Control Panel from the Start button. Once the
Control Panel opens, select Printer from the Hardware and Sound section.

1. Access the Printing Preferences for the Microboards PF3. How this is done
will depend on the Operating System and the currently selected Start Menu
layout.

In Windows 2000 or Windows XP with the Classic Start Menu layout, you will
need to go to the Settings selection, then to the Printers and Faxes from the
Start button.

In Windows Vista, select the Control Panel from the Start button. Once the
Control Panel opens, select Printer from the Hardware and Sound section.

In the Windows XP Start Menu layout, select Printers and Faxes from the
Windows Start button.

In Windows 2000 or Windows XP with the Classic Start Menu layout, you will
need to go to the Settings selection, then to the Printers and Faxes from the
Start button. Right-click the Microboards PF3 and select Printing Preferences.
In the Windows XP Start Menu layout, select Printers and Faxes from the
Windows Start button.

NOTE: THE ALIGNMENT VALUES MUST BE ENTERED THROUGH THE
PRINTERS AND FAXES WINDOW FOR THE SETTINGS TO BE SET AS THE
DEFAULT SETTINGS, NOT FROM WITHIN ANY APPLICATION!!!
2. Right click on the icon for the Microboards PF3 and select Printing
Preferences…

2. Click the Diameter Settings
tab.

3. On the Print Quality tab, select Photo for the Print Mode and Best or Max
DPI for the Print Quality.

3. Verify that the Enable
Masking option is checked.
The first Microboards PF3
Series printer will have this
option checked by default; any
subsequent printer installed will
not have this option checked.

Photo Best or Max DPI should always be selected when aligning the printer, in
order to insure the greatest accuracy during the alignment process. Other
settings may not result in the best alignment.

4. The Outer Diameter setting
will define where the masking
clips the outer edge of the print image. In the example shown below, the image
will print to the default diameter of 118mm (the Parameter Unit is set to 0.1mm).
The Inner Diameter setting will define how far towards the center of the disc
the image will print. This setting will need to be changed when printing to hubprintable media. The default of 36mm diameter of unprinted area is shown
below.
5. Click the Apply button to save the changes.

4. Select the Alignment tab. The .1mm
Resolution setting must be selected
before setting alignment values (see
below). Set the Top and Left Side
alignment values to those required for
image alignment.

The functions of the Toolbox
include:

• Printhead Cleaning Utilities
• Pen Calibration
• Automatic Margin Calibration
• Test Print
• Belt Exerciser
• Low Ink warnings
For more information on the Toolbox, please refer to the User’s Manual.

Be sure your computer meets the Minimum System Requirements as stated
in the User’s Manual and that you have read these instructions and the
Manual prior to contacting Microboards Technical Support with installation
or configuration questions!

These settings will change the size of the top and left margins, respectively.
Decreasing the values will move the image up or to the left, increasing will
adjust down or to the right.
5. Click the Apply button to save the changes, found on the bottom of the Printing
Preferences window.
6. Verify the alignment by printing a full disc image on the media. Repeat these
steps if further alignment adjustments are required.

For further details on the alignment process, please refer to the
section on Alignment in the PF-3 Print Factory User’s Manual.

In order to guarantee quality results from the PF-3 Print Factory,

ONLY V102C and V101B
INK CARTRIDGES CAN BE USED!
As is true with all printers, the quality of ink cartridge and the quality of the ink
within the cartridge will affect your output. To ensure quality results, the PF-3
Print Factory will not operate with any other ink cartridges in place.

The use of refilled ink cartridges will void your warranty!
Please visit our Technical Support website at www.microboards.net

820-00229-01



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : PageMaker 7.0
Modify Date                     : 2007:11:21 08:23-06:00
Create Date                     : 2007:11:21 08:23-06:00
Format                          : application/pdf
Title                           : PRF-3 QRG 2.PMD
Creator                         : andrews
Document ID                     : uuid:f141efd3-7bfd-4f13-b1fd-ec1c904a6b21
Instance ID                     : uuid:18ce5a8d-3354-42de-8efa-ef8162edba5b
Page Count                      : 2
Author                          : andrews

EXIF Metadata provided by EXIF.tools