Microchip Technology BZR ATSAMB11-ZR210CA BLE Module User Manual ATSAMB11 ZR210CA USER MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	3531010
Application ID	wLRHlLdBoFyZOVZH/MBqBA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.6kB (107529 bits)
Date Submitted	2017-08-28 00:00:00
Date Available	2017-08-28 00:00:00
Creation Date	2017-07-06 14:48:34
Producing Software	GPL Ghostscript 9.06
Document Lastmod	2017-07-06 14:48:34
Document Title	Microsoft Word - ATSAMB11-ZR210CA USER-MANUAL
Document Creator	PScript5.dll Version 5.2.2
Document Author:	C17148

ATSAMB11-ZR210CA DESIGN-IN GUIDELINES
ATSAMB11-ZR210CA module is based on Microchip Atmel’s industry-leading low-power 2.4GHz
Bluetooth Low Energy (BLE) ATSAMB11-XR2100A SiP (System in a Package).
The ATSAMB11-XR2100A is an ultra-low power Bluetooth SMART (BLE 4.1) System in a Package with
Integrated MCU, Transceiver, Modem, MAC, PA, TR Switch, Power Management Unit (PMU), and a
26MHz crystal. It is a stand-alone Cortex-M0 application processor with embedded Flash memory and
BLE connectivity.
The qualified Bluetooth Smart protocol stack is stored in dedicated ROM, the firmware includes L2CAP
service layer protocols, Security Manager, Attribute protocol (ATT), Generic Attribute Profile (GATT) and
the Generic Access Profile (GAP). Additionally, application profiles such as Proximity, Thermometer,
Heart Rate, Blood Pressure, and many others are supported and included in the protocol stack.
The ATSAMB11-ZR210CA module contains the ATSAMB11-XR2100A SiP, a 2.4 – 2.5GHz antenna, RF
matching. The following connections are required for proper operation:
•
•
•
•
Power supply, minimum 2.3V, typically 3.6V, maximum 4.3V, to power the BLE module (VBAT)
Power supply, minimum 2.3V, typically 3.3V, maximum 3.6V for VDDIO. Note that VBAT must
be greater than or equal to VDDIO
Logic control for Chip_En signal
A 32.768KHz real time clock or crystal
When the module is placed in the system, a provision for the antenna must be made. There should be
nothing under the portion of the module which contains the antenna. This means the antenna should
not be placed directly on top of the motherboard PCB. This can be accomplished by, for example,
placing the module at the edge of the board such that the antenna extends beyond the board edge by
3.0mm. Alternatively, a cut out in the motherboard can be provided under the antenna. The cutout
should be at least 7.5mm x 3.0mm. Ground vias should be placed all around the perimeter of the
cutout. No large component should be placed near the antenna.
The module is too small (7.5 x 10.5mm) to put the FCC ID on the module and to be readable. Microchip
has applied for the FCC ID to be added to the Datasheet and to the shipping package instead of the
module. In addition, the product User Manual must contain the following statement:
“Contains Transmitter Module FCC ID: 2ADHKBZR or Contains FCC ID: 2ADHKBZR
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation”.
A sample label is shown below.
The module must be installed into the end product to provide a separation distance of at least 5mm
from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter.
If the module’s label is not visible when installed, then an additional permanent label referring to the
enclosed module” “Contains Transmitter Module FCC ID: 2ADHKBZR” or “Contains Transmitter Module
IC: 20266-SAMB11ZR” must be installed on the product in a visible location.
A user’s manual for the finished product should include the following statement:
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Re-orient or relocate the module/product
Increase the separation between the equipment and the module/product
Consult the dealer or an experienced radio/TV technician for help
Changes and modifications made to the equipment without the approval of manufacturer could void the
user’s authority to operate this equipment.
Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of
the device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5bb888f1-64f0-11e7-0000-85200af4a749
Producer                        : GPL Ghostscript 9.06
Modify Date                     : 2017:07:06 14:48:34-07:00
Create Date                     : 2017:07:06 14:48:34-07:00
Creator Tool                    : PScript5.dll Version 5.2.2
Document ID                     : uuid:5bb888f1-64f0-11e7-0000-85200af4a749
Format                          : application/pdf
Title                           : Microsoft Word - ATSAMB11-ZR210CA USER-MANUAL
Creator                         : C17148
Author                          : C17148

EXIF Metadata provided by EXIF.tools