Microduino MCBL53 mCookie Module WIFI User Manual
Microduino Inc. mCookie Module WIFI
User manual
mCookie-WIFI(ESP) is a WIFI communication module, which can communicate with
Core/Core+/CoreUSB through the serial port or connect with other WIFI devices and is a
complete and system-in-itself wifi network resolution.
Specification
Communication method: Serial passthrough with the default serial port D2(RX),
D3(TX);
Power supply: +3.3V DC 100mA;
Status indicator;
SDIO 2.0, SPI and UART interface;
32-pin QFN sealed ;
With RF switch, balun, LNA, 24 PA dBm, DCXO and power management unit
(PMU) integrated;
With RISC processor, on-chip memory and external memory interface integrated;
With MAC/ baseband processor integrated;
High quality service management;
With I2S interface required by high fidelity audio applications;
All internal power supply contains on-chip low dropout linear regulator;
Proprietary spurious free clock generation architecture;
With WEP, TKIP, AES, and WAPI engines integrated.
Common AT Instruction
All AT instructions are ended with "\r\n ". When debugging the AT commands,
please pay attention to the choice of "\r\n".
Common AT instruction:
o AT+RST Restart the module;
o AT+GMR Check the version information;
o AT+CWMODE=3 Station and access point;
1 Station Mode;
2 AP Mode;
3 AP and the Station.
o AT+CWLAP WIFI SSID List;
o AT+CWSMARTSTART=0 Start smart connection:
0: Adopt AL-LINK technology;
1: Adopt ESP-TOUCH;
2: Adopt AIR-KISS.
o AT+CWSMARTSTOP Stop the smart connection;
o AT+CWJAP="<access_point_name>","<password>" Join in a certain
WIFI;
o AT+CIFSR Display the information of wifi;
o AT+CIPSTATUS Acquire the connection status;
o AT+CIPSTART=4,"TCP","baidu.com",80 Establish TCP/UDP connection
and ports;
o AT+CIPCLOSE Close the connection of TCP/UDP(single connection);
o AT+CIPCLOSE=5 Close multiple connections;
o AT+CIPMUX=1 Start multiple connections.
Documents
AT command instruction：File:ESP8266 AT Instruction Set CN v0.30.pdf
AT command instruction：File:ESP8266 AT Instruction Set EN v0.30.pdf
AT command example：File:ESP8266 AT Command Examples CN v0.5.pdf
AT command example：File:ESP8266 AT Command Examples EN v0.5.pdf
Development
Test program
o Use Microduino IDE-->
example-->_03_microduino_WiFi_ESP8266-->HTTPGET program test is
OK.
Download program
o Stack together with Microduino-WiFi(ESP), Microduino-Core+ and
Microduino-USBttl,
insert USB line into the Microduino-USBttl, other side of USB line insert into
computer, start Arduino IDE, The above program is copied to the IDE, the tool
(tools) -> Board (Board) is selected Microduino Core, and the tools (tools) ->
Serial Port (Serial) select the corresponding serial number. After clicking the
top left corner IDE √ button to compile the program, after the end of the
compilation click -> button is programmed to the board;
Open the serial monitor, set:"\r\n", "115200 baud".
First of prompts is to show connect WiFi successful information
If you see the following description you already visited Baidu Home website.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example,
USB dongle like transmitters is forbidden.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20
cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the
module
is
installed
must
also
display
a
label
referring
to
the
enclosed
module.
This
exterior
label
can
use
wording
such
as
the
following:
“Contains Transmitter Module
FCC ID: 2AKMKMCBL53 Or
Contains FCC ID: 2AKMKMCBL53”
When the module is installed inside another device, the user manual of the host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that
comes with the product
Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission
and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and
15.209 requirement，then the host can be sold legally.
MCBL53：
A
side：
B side：
MDBL53：
A
side：
B side：