Microhard Systems 04P11 MHX910 A 900MHz SPREAD SPECTRUM OEM MODULE User Manual MHX910AmanualREV0 10 FCC
Microhard Systems Inc MHX910 A 900MHz SPREAD SPECTRUM OEM MODULE MHX910AmanualREV0 10 FCC
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 493858 |
| Application ID | gNjOwsPuz7C6G1KH4hmm1w== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 19.56kB (244497 bits) |
| Date Submitted | 2004-12-03 00:00:00 |
| Date Available | 2004-12-03 00:00:00 |
| Creation Date | 2004-11-01 18:59:25 |
| Producing Software | Acrobat Distiller 5.0 (Windows) |
| Document Lastmod | 2004-11-29 13:33:51 |
| Document Title | Microsoft Word - MHX910AmanualREV0.10.FCC.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | llei |
Operating Manual MHX-910A 900 MHz Spread Spectrum OEM Module Revision 0.10, November 1, 2004 Microhard Systems Inc. #17, 2135 - 32nd Ave. N.E. Calgary, Alberta T2E 6Z3 Phone: (403) 248-0028 Fax: (403) 248-2762 www.microhardcorp.com MHX 910A Operating Manual Warranty Microhard Systems Inc. warrants that each product will be free of defects in material and workmanship for a period of one (1) year for its products. The warranty commences on the date the product is shipped by Microhard Systems Inc. Microhard Systems Inc.’s sole liability and responsibility under this warranty is to repair or replace any product which is returned to it by the Buyer and which Microhard Systems Inc. determines does not conform to the warranty. Product returned to Microhard Systems Inc. for warranty service will be shipped to Microhard Systems Inc. at Buyer’s expense and will be returned to Buyer at Microhard Systems Inc.’s expense. In no event shall Microhard Systems Inc. be responsible under this warranty for any defect which is caused by negligence, misuse or mistreatment of a product or for any unit which has been altered or modified in any way. The warranty of replacement shall terminate with the warranty of the product. Warranty Disclaims Microhard Systems Inc. makes no warranties of any nature of kind, expressed or implied, with respect to the hardware, software, and/or products and hereby disclaims any and all such warranties, including but not limited to warranty of non-infringement, implied warranties of merchantability for a particular purpose, any interruption or loss of the hardware, software, and/or product, any delay in providing the hardware, software, and/or product or correcting any defect in the hardware, software, and/or product, or any other warranty. The Purchaser represents and warrants that Microhard Systems Inc. has not made any such warranties to the Purchaser or its agents MICROHARD SYSTEMS INC. EXPRESS WARRANTY TO BUYER CONSTITUTES MICROHARD SYSTEMS INC. SOLE LIABILITY AND THE BUYER’S SOLE REMEDIES. EXCEPT AS THUS PROVIDED, MICROHARD SYSTEMS INC. DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PROMISE. MICROHARD SYSTEMS INC. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE USED IN ANY LIFE SUPPORT RELATED DEVICE OR SYSTEM RELATED FUNCTIONS NOR AS PART OF ANY OTHER CRITICAL SYSTEM AND ARE GRANTED NO FUNCTIONAL WARRANTY. Indemnification The Purchaser shall indemnify Microhard Systems Inc. and its respective directors, officers, employees, successors and assigns including any subsidiaries, related corporations, or affiliates, shall be released and discharged from any and all manner of action, causes of action, liability, losses, damages, suits, dues, sums of money, expenses (including legal fees), general damages, special damages, including without limitation, claims for personal injuries, death or property damage related to the products sold hereunder, costs and demands of every and any kind and nature whatsoever at law. IN NO EVENT WILL MICROHARD SYSTEMS INC. BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL, BUSINESS INTERRUPTION, CATASTROPHIC, PUNITIVE OR OTHER DAMAGES WHICH MAY BE CLAIMED TO ARISE IN CONNECTION WITH THE HARDWARE, REGARDLESS OF THE LEGAL THEORY BEHIND SUCH CLAIMS, WHETHER IN TORT, CONTRACT OR UNDER ANY APPLICABLE STATUTORY OR REGULATORY LAWS, RULES, REGULATIONS, EXECUTIVE OR ADMINISTRATIVE ORDERS OR DECLARATIONS OR OTHERWISE, EVEN IF MICROHARD SYSTEMS INC. HAS BEEN ADVISED OR OTHERWISE HAS KNOWLEDGE OF THE POSSIBILITY OF SUCH DAMAGES AND TAKES NO ACTION TO PREVENT OR MINIMIZE SUCH DAMAGES. IN THE EVENT THAT REGARDLESS OF THE WARRANTY DISCLAIMERS AND HOLD HARMLESS PROVISIONS INCLUDED ABOVE MICROHARD SYSTEMS INC. IS SOMEHOW HELD LIABLE OR RESPONSIBLE FOR ANY DAMAGE OR INJURY, MICROHARD SYSTEMS INC.'S LIABILITY FOR ANYDAMAGES SHALL NOT EXCEED THE PROFIT REALIZED BY MICROHARD SYSTEMS INC. ON THE SALE OR PROVISION OF THE HARDWARE TO THE CUSTOMER. Proprietary Rights The Buyer hereby acknowledges that Microhard Systems Inc. has a proprietary interest and intellectual property rights in the Hardware, Software and/or Products. The Purchaser shall not (i) remove any copyright, trade secret, trademark or other evidence of Microhard Systems Inc.’s ownership or proprietary interest or confidentiality other proprietary notices contained on, or in, the Hardware, Software or Products, (ii) reproduce or modify any Hardware, Software or Products or make any copies thereof, (iii) reverse assemble, reverse engineer or decompile any Software or copy thereof in whole or in part, (iv) sell, transfer or otherwise make available to others the Hardware, Software, or Products or documentation thereof or any copy thereof, except in accordance with this Agreement. ii MHX 910A Operating Manual Regulatory Requirements WARNING To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 23 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. WARNING This device can only be used with Antennas listed in Appendix A. Please Contact Microhard Systems Inc. if you need more information or would like to order an antenna. WARNING MAXIMUM ERP FCC Regulations allow up to 36 dBm effective radiated power (ERP). Therefore, the sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36 dBm. WARNING EQUIPMENT LABELING This device has been modularly approved. The manufacturer, product name, and FCC and Industry Canada identifiers of this product must appear on the outside label of the end-user equipment. SAMPLE LABEL REQUIREMENT: FCCID: NS904P11 IC: 3143A-04P11 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. MHX 910A Operating Manual iii Contents CONTENTS .............................................................................................................................................................. III HISTORY....................................................................................................................................................................V TABLES AND FIGURES .......................................................................................................................................VII TABLES ....................................................................................................................................................................................... VII FIGURES ...................................................................................................................................................................................... VII 1. INTRODUCTION ...............................................................................................................................................1 1.0 1.1 2. CONFIGURATION ............................................................................................................................................4 2.0 2.1 3. OVERVIEW ....................................................................................................................................................................... 4 OUTPUT POWER LEVEL ..................................................................................................................................................... 4 INSTALLATION.................................................................................................................................................7 3.0 3.1 3.2 3.3 A. PRODUCT OVERVIEW ........................................................................................................................................................ 1 FEATURES ........................................................................................................................................................................ 2 OVERVIEW ....................................................................................................................................................................... 7 ESTIMATING THE GAIN MARGIN ....................................................................................................................................... 7 INTERNAL CABLING .......................................................................................................................................................... 9 INSTALLING EXTERNAL CABLES, ANTENNAS AND LIGHTNING ARRESTORS...................................................................... 10 APPROVED ANTENNAS ............................................................................................................................15 MHX 910A Operating Manual: Contents iii History Revision Date Action 0.10 2004-11-01 Created MHX 910A Operating Manual: History FW Rev. Note For FCC Approval Tables and Figures Tables Table 1 Path Loss ..........................................................................................................................................................8 Table 2 Cable Loss ......................................................................................................................................................10 Figures Figure 1 Gain Calculation.............................................................................................................................................7 Figure 2 System Deploying ...........................................................................................................................................8 Figure 3 Suggested Internal Cabling .............................................................................................................................9 MHX 910A Operating Manual: Tables and Figures vii 1. Introduction 1.0 Product Overview The MHX-910A is a very high-performance wireless module. When used properly very long distance communication at very high speeds can be accomplished. The MHX-910A operates in the 902 - 928 MHz ISM band, using frequency-hopping spread-spectrum module is capable of providing reliable wireless data transfer between almost any equipment which uses an RS232, RS422, or RS485 interfaces. The small-size and superior RF performance of this product makes it ideal for many applications. Typical uses for this module include: SCADA Remote Telemetry Surveillance Traffic Control Industrial Controls Remote Monitoring Fleet Management GPS Wireless Video Robotics Security Display Signs Railway Signaling Many others While a pair of MHX-910A modules can link two terminal devices (“pointto-point” operation), multiple modules can be used together to create a network of various topologies, including “point-to-multipoint” and “repeater” operation. Multiple independent networks can operate concurrently, so it is possible for unrelated communications to take place in the same or a nearby area without sacrificing privacy or reliability. MHX 910A Operating Manual: Chapter 1 Introduction 1.1 Features Key features of the MHX-910A include: transmission within a public, license-exempt band of the radio spectrum1 – this means that it can be used without access fees (such as those incurred by cellular airtime); Transparent, low latency link providing true 115.2 kbps continuous throughput Communicates with virtually all PLCs, RTUs, and serial devices through RS232, RS422 and RS485 interface 3.3V or 5V logic level compatibility Industrial temperature specifications Supports point-to-point, point-to-multipoint, Store and Forward Repeater, TDMA, Multimaster Maximum allowable transmit power, (1W) Low power consumption in Sleep Mode (Real-Time Clock wakeup) 32-bit CRC, selectable forward error correction with retransmission Separate diagnostics port - transparent remote diagnosis and online network control Backwards Compatible with MHX-910 ease of installation and use – the MHX-910A module uses a subset of standard AT style commands, very similar to those used by traditional telephone line modules. While the typical application for the MHX-910A is to provide a short- to mid-range wireless communications link between DTEs, it can be adapted to almost any situation where an asynchronous serial interface is used and data intercommunication is required. 902-928 MHz, which is license-free within North America; may need to be factory-configured differently for some countries. MHX 910A Operating Manual: Chapter 1 Introduction MHX 910A Operating Manual: Chapter 1 Introduction 2. Configuration 2.0 Overview This chapter provides a detailed description of the various operating parameters of the MHX-910A. 2.1 Output Power Level The Output Power Level determines at what power the MHX-910A transmits. The MHX-910A’s sensitive receiver can operate with very low power levels, so it is recommended that the lowest power necessary is used; using excessive power contributes to unnecessary “RF pollution”. The allowable settings are: *2 1 mW 10 mW 100 mW 1000 mW Ideally, you should test the communications performance between units starting from a low power level and working upward until the RSSI is sufficiently high and a reliable link is established. The conditions will vary widely between applications; the output power settings can be calculated based on following information. • Transmitter antenna gain • Cable loss • Effective radiated power (ERP) requirement by FCC Regulations Power Setting = 36 – Antenna Gain – Cable Loss The power setting must be no more than the above calculation value. Any higher is a violation of FCC rules. MHX 920 Operating Manual: Chapter 2 Configuration WARNING In order to comply with the FCC/IC adopted RF exposure requirements, this transmitter system will be installed by the manufacturer's reseller professional. Installation of all antennas must be performed in a manner that will provide at least 23 cm clearance from the front radiating aperture, to any user or member of the public. IMPORTANT: FCC Regulations allow up to 36 dBi effective radiated power (ERP). Therefore, the sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36 dBi. 1 mW = 0 dBm 10 mW = 10 dBm 100 mW = 20 dBm 1000 mW = 30 dBm For example, when transmitting 1 Watt (30 dBm), with cabling losses of 2 dB, the antenna gain cannot exceed 36 - 30 + 2 = 8 dBi. If an antenna with a gain higher than 8 dBi were to be used, the power setting must be adjusted appropriately. Violation of FCC regulations can result in severe fines. MHX 920 Operating Manual: Chapter 2 Configuration 3. Installation 3.0 Overview The installation, removal or maintenance of all antenna components must be carried out by qualified and experienced personnel. The MHX-910A complies with FCC part 15 at the modular level for operation in the license-free 902-928 MHz ISM band. This chapter provides guidelines for installing and deploying equipment which incorporates the MHX-910A module. 3.1 Estimating the Gain Margin Successful communication between MHX-910A modules is dependent on three main factors: • System Gain • Path Loss • Interference System gain is a calculation in dB describing the performance to be expected between a transmitter-receiver pair. The number can be calculated based on knowledge of the equipment being deployed. The following four factors make up a system gain calculation: 1. Transmitter power (user selectable 0, 20 to 30dBm) 2. Transmitter gain (transmitting antenna gain minus cabling loss between the transmitting antenna and the MHX-910A module) 3. Receiver gain (Receiving antenna gain minus cabling loss between the receiving antenna and the module) 4. Receiver sensitivity (Specified as -105dBm on the MHX-910A module) In the following illustration, the transmitting antenna has a gain of 6 dB, and the receiving antenna has a gain of 3 dB. The cable loss between the module and the antenna is 2 dB on both the transmitting and receiving side. Cable Loss = 2 dB Antenna Gain = 6 dB Cable Loss = 2 dB Antenna Gain = 3 dB Transmitter Receiver 30 dBm Output Power Sensitivity = -105 dBm Figure 1 Gain Calculation MHX 910A Operating Manual: Chapter3 Installation The power level has been set to 30dBm (1W) on the transmitter, and the receiver sensitivity for the MHX-910A is -105dBm. System gain can be calculated: Base Height (m) 30 - 2 + 6 + 3 - 2 + 105 = 140 dB. Mobile Height (m) Distance (km) Figure 2 System Deploying When deploying your system, care must be taken to ensure the path loss (reduction of signal strength from transmitter to receiver in dB) between equipment does not exceed the system gain (140 dB in the above example). It is recommended to design for a gain margin of at least 20 dB to ensure reliable communication. Gain margin is the difference between system gain and path loss. Referring to the same example, suppose the path loss is 113 dB, the gain margin would be 30 dB, which is more than adequate for reliable communication. Path loss is a very complicated calculation which mainly depends on the terrain profile, and the height of the antennas off the ground. The following table provides path loss numbers for varying antenna heights and antenna separation: These numbers are real averages taken from rural environments. They do not apply to urban, non-line-of-sight environments. Table 1 Path Loss Distance (km) Base Height (m) Mobile Height (m) Path Loss (dB) 15 2.5 116.5 30 2.5 110.9 15 2.5 124.1 15 117.7 15 10 105 16 15 2.5 135.3 16 15 128.9 16 15 10 116.2 16 30 10 109.6 16 30 122.4 16 30 2.5 128.8 Once the equipment is deployed, you can verify the signal strength by entering into Command Mode and reading Register S123. This register provides the average signal strength in dBm. The minimum strength for communication is roughly -105dBm. For consistent reliable communication, you should try to deploy the equipment such that signal strength exceeds 85dBm. MHX 920 Operating Manual: Chapter 3 Installation 3.2 Internal Cabling This section describes the recommended procedure for installing cabling and antennas for use with the MHX-910A module. The most common method for installing the module is to run a cable from the module’s MCX connector to a reverse TNC bulkhead connector on the chassis of the equipment as shown in Figure 3. This cable can be purchased from Microhard Systems. Reverse TNC connector RG316 Cable with MCX male connector and Reverse TNC bulkhead connector MHX-910A MCX female connector Figure 3 Suggested Internal Cabling Cable losses are negligible for the short piece used within the chassis. Additional losses up to 0.5 dB may be present in the MCX and Reverse TNC connections. MHX 910A Operating Manual: Chapter3 Installation 3.3 Installing External Cables, Antennas and Lightning Arrestors WARNING To satisfy FCC RF exposure requirements for mobile transmitting devices, separation distance of 23 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be colocated in conjunction with any other antenna or transmitter WARNING Direct human contact with the antenna is potentially unhealthy when a MHX910A is generating RF energy. Always ensure that the MHX-910A equipment is powered down during installation. The installation, removal or maintenance of all antenna components must be carried out by qualified and experienced personnel. Never work on an antenna system when there is lightning in the area. Direct human contact with the antenna is potentially unhealthy when the MHX-910A is generating RF energy. Always ensure that the MHX-910A equipment is powered down during installation. At all time, a distance of 23 cm must be maintained between the antenna and any person when the device is in operation. Surge Arrestors The most effective protection against lightning is to install two lightning (surge) arrestors, one at the antenna, the other one at the interface with the equipment. The surge arrestor grounding system should be fully interconnected with the transmission tower and power grounding systems to form a single, fully integrated ground circuit. Typically, both ports on surge arrestors are N-female. External Filter Although the MHX-910A is capable of filtering out RF noise in most environments, there are circumstances that require external filtering. Paging towers, and cellular base stations in close proximity to the MHX-910A antenna can desensitize the receiver. Microhard Systems’ external cavity filter eliminates this problem. The filter has two N-female ports and should be connected in line at the interface to the RF equipment. Weatherproofing Type N and RTNC connectors are not weatherproof. All connectors should be taped with rubber splicing tape (weatherproofing tape), and then coated with a sealant. Cabling The following coax cables are recommended: WARNING Never work on an antenna system when there is lightning in the area. 10 Table 2 Cable Loss Cable Loss (dB/100ft) LMR 195 10.7 LMR 400 3.9 LMR 600 2.5 MHX 910A Operating Manual: Chapter3 Installation Factors to take into consideration when choosing a cable are: • price; • bend radius limitations (the lower performance cables generally can bend more sharply) • performance requirements; and, • distance between the equipment and the antenna. When installing the cable, always begin fastening at the top near the antenna connector/surge arrestor. The cable must be supported at the top with a hose clamp or wrap lock, and at 5 ft intervals down the length of the tower. Overtightening the fasteners will dent the cable and reduce performance. If properly grounded surge arrestors are not installed at both the top and the bottom of the cable, then the cable should be grounded to the tower at these locations using a cable grounding kit. If the tower is non-conductive, then a separate conductor, physically separate from the cable, should be run down the tower. MHX 910A Operating Manual: Chapter3 Installation 11 Antenna Before choosing an antenna, you should have some knowledge of the path loss and the topology of the equipment. If the equipment is in a fixed location and is to communicate with only one other unit also in a fixed location, then a Yagi antenna is suitable. Choose a Yagi with enough gain to ensure adequate gain margin. When deploying the Yagi, point the antenna towards the intended target, ensuring the antenna elements are perpendicular to the ground for vertical polarization. In applications where there are multiple units that you must communicate with or units, which are in motion, you may select an Omni-directional antenna with appropriate gain. To comply with FCC regulations, .you must limit ERP to 36 dBm or less. FCC Regulations allow up to 36dBm effective radiated power (ERP). Therefore, the sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36dBm with respect to the isotropic radiator. ERP is calculated as follows: ERP = Tx Power (dBm) - Cable/Connector Loss (dB) + Antenna Gain (dBi) Antenna Gains must be in dBi when calculating the 36dBm ERP limit. 1dBd = 2.15dBi Use the guidelines in the previous section for calculating cable and connector losses. If cabling and connector losses are 2 dB, then the maximum allowable gain of the antenna will be 8 dB. 12 MHX 920 Operating Manual: Chapter 3 Installation Examples: FCC and Industry Canada Regulations allow up to 36dBm effective radiated power (ERP). Therefore, the sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36dBm with respect to the isotropic radiator. Example 1) What is the maximum power the MHX-910A can be set to comply with FCC and IC given the following equipment given a Rubber Ducky Antenna Gain 2dBi and no cable or connectors in the system? Max ERP 36dBm Max TX power = ERP – Ant Gain(dBi) + Cable/Connector loss (dB) Ant Gain dBi = 2dBi Max TX power = 36dBm – 2dBi + 0dB = 34dBm We can set the modem to the maximum power setting of 30dBm. Example 2) What is the maximum power the MHX-910A can be set to comply with FCC and IC given the following equipment given a Yagi Antenna Gain 12dBd and cable and connector loss of 4.5 dB? Max ERP 36dBm Max TX power = ERP – Ant Gain(dBi) + Cable/Connector loss (dB) Ant Gain dBi = Ant Gain dBd + 2.15 dB Yagi Gain (dBi) = 12 + 2.15 = 14.15dBi Max TX power = 36dBm – 14.15dB + 4.5dB = 26.35dBm We must round down Hence Max TX power = 26dBm Example 3) What is the maximum power the MHX-910A can be set to comply with FCC and IC given the following equipment given a Omni Antenna Gain 6dBd and cable and connector loss of 2.5 dB? Max ERP 36dBm Max TX power = ERP – Ant Gain(dBi) + Cable/Connector loss (dB) Ant Gain dBi = Ant Gain dBd + 2.15 dB Omni Gain (dBi) = 6 + 2.15 = 8.15dBi Max TX power = 36dBm – 8.15dB + 2.5dB = 30.35dBm Hence Max TX power = 30dBm MHX 910A Operating Manual: Chapter3 Installation 13 14 MHX 920 Operating Manual: Chapter 3 Installation A. Approved Antennas Group Part Number Description Quarter Wave MHS031010 <1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Right Angle MHS031020 <1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Straight MHS031030 <1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Right Angle MHS MHS031040 <1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Straight MHS MHS031050 <1.5dBi, 900MHz 1/4 Wave Antenna MCX Right Angle MHS MHS031060 <1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Straight MHS031000 2dBi, 900MHz Rubber Ducky Antenna RPTNC Swivel Rubber Ducky MHS031070 2dBi, 900MHz Rubber Ducky Antenna Reverse SMA Swivel MHS031080 2dBi, 900MHz Rubber Ducky Antenna Reverse SMA Straight MHS031210 3dBd, 900 MHz Transit Antenna with Ground Plane MHS031220 3dBd, 900MHz Transit Antenna No Ground Plane MHS031230 3dBd, 900MHz Transit Antenna Permanent Mount GP MHS031240 3dBd, 900MHz Transit Antenna Permanent Mount NGP Transit Antennas Mounts for Transit Antennas have a RPTNC Pigtail Yagi Antennas MHS031311 6dBd, 900MHz Yagi Directional Antenna Antenex, RPTNC Pigtail MHS031431 6.5dBd, 900MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail MHS031501 9dBd, 900MHz Yagi Directional Antenna Antenex, RPTNC Pigtail MHS031441 10dBd, 900 MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail MHS031451 11dBd, 900 MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail MHS031401 12dBd, 900MHz Yagi Directional Antenna Antenex, RPTNC Pigtail MHS031411 12dBd, 900MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail MHS031251 3dBd, 900MHz Omni Directional Antenna Antenex, RPTNC Pigtail MHS031461 3dBd, 900 MHz Omni Directional Antenna Bluewave, RPTNC Pigtail MHS031321 6dBd, 900MHz Omni Directional Antenna Antenex, RPTNC Pigtail MHS031471 6dBd, 900 MHz Omni Directional Antenna Bluewave, RPTNC Pigtail Omni Directional WARNING Changes or modifications not expressly approved by Microhard Systems Inc. could void the user’s authority to operate the equipment. This device has been tested with MCX and Reverse Polarity SMA connectors with the antennas listed in Appendix A When integrated in OEM products, fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique antenna connectors) and Section 15.247 (emissions). Please Contact Microhard Systems Inc. if you need more information. MHX 910A Operating Manual: Appendix A Approved Antennas 15 16 MHX 910A Operating Manual: Appendix A Approved Antennas
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 26 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:20374bf0-5110-4bb7-b80e-0c3c888192b1 Producer : Acrobat Distiller 5.0 (Windows) Create Date : 2004:11:01 18:59:25Z Modify Date : 2004:11:29 13:33:51-05:00 Metadata Date : 2004:11:29 13:33:51-05:00 Creator Tool : PScript5.dll Version 5.2 Document ID : uuid:08f21482-9163-49b5-90bd-8c9b31d25f9b Format : application/pdf Creator : llei Title : Microsoft Word - MHX910AmanualREV0.10.FCC.doc Author : lleiEXIF Metadata provided by EXIF.tools