Microhard Systems 08P24 n920 - 900 MHz OEM Frequency Hopping Module User Manual n920FSmanualREV0 40 FCC

Download:
Mirror Download [FCC.gov]
Document ID	941069
Application ID	loTjqogzzAfvM5oieAiyJg==
Document Description	Revised User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.86kB (248263 bits)
Date Submitted	2008-05-14 00:00:00
Date Available	2008-04-18 00:00:00
Creation Date	2008-05-13 03:42:44
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2008-05-13 13:44:47
Document Title	Microsoft Word - n920FSmanualREV0.40.FCC.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	hshenouda

Operating Manual
n920
900 MHz Spread Spectrum OEM Transceiver
Revision 0.10, May 12, 2008
Microhard Systems Inc.
#17, 2135 – 32nd Ave N.E.
Calgary, Alberta T3K 4Z4
Phone: (403) 248-0028
Fax: (403) 248-2762
www.microhardcorp.com
Warranty
Microhard Systems Inc. warrants that each product will be free of defects in material and workmanship for a period of one (1)
year for its products. The warranty commences on the date the product is shipped by Microhard Systems Inc. Microhard Systems
Inc.’s sole liability and responsibility under this warranty is to repair or replace any product which is returned to it by the Buyer
and which Microhard Systems Inc. determines does not conform to the warranty. Product returned to Microhard Systems Inc. for
warranty service will be shipped to Microhard Systems Inc. at Buyer’s expense and will be returned to Buyer at Microhard
Systems Inc.’s expense. In no event shall Microhard Systems Inc. be responsible under this warranty for any defect which is
caused by negligence, misuse or mistreatment of a product or for any unit which has been altered or modified in any way. The
warranty of replacement shall terminate with the warranty of the product.
Warranty Disclaims
Microhard Systems Inc. makes no warranties of any nature of kind, expressed or implied, with respect to the hardware, software,
and/or products and hereby disclaims any and all such warranties, including but not limited to warranty of non-infringement,
implied warranties of merchantability for a particular purpose, any interruption or loss of the hardware, software, and/or product,
any delay in providing the hardware, software, and/or product or correcting any defect in the hardware, software, and/or product,
or any other warranty. The Purchaser represents and warrants that Microhard Systems Inc. has not made any such warranties to
the Purchaser or its agents MICROHARD SYSTEMS INC. EXPRESS WARRANTY TO BUYER CONSTITUTES
MICROHARD SYSTEMS INC. SOLE LIABILITY AND THE BUYER’S SOLE REMEDIES. EXCEPT AS THUS
PROVIDED, MICROHARD SYSTEMS INC. DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PROMISE.
MICROHARD SYSTEMS INC. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE USED IN
ANY LIFE SUPPORT RELATED DEVICE OR SYSTEM RELATED FUNCTIONS NOR AS PART OF
ANY OTHER CRITICAL SYSTEM AND ARE GRANTED NO FUNCTIONAL WARRANTY.
Indemnification
The Purchaser shall indemnify Microhard Systems Inc. and its respective directors, officers, employees, successors
and assigns including any subsidiaries, related corporations, or affiliates, shall be released and discharged from any
and all manner of action, causes of action, liability, losses, damages, suits, dues, sums of money, expenses
(including legal fees), general damages, special damages, including without limitation, claims for personal injuries,
death or property damage related to the products sold hereunder, costs and demands of every and any kind and
nature whatsoever at law.
IN NO EVENT WILL MICROHARD SYSTEMS INC. BE LIABLE FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL, INCIDENTAL, BUSINESS INTERRUPTION, CATASTROPHIC, PUNITIVE OR OTHER
DAMAGES WHICH MAY BE CLAIMED TO ARISE IN CONNECTION WITH THE HARDWARE,
REGARDLESS OF THE LEGAL THEORY BEHIND SUCH CLAIMS, WHETHER IN TORT, CONTRACT OR
UNDER ANY APPLICABLE STATUTORY OR REGULATORY LAWS, RULES, REGULATIONS,
EXECUTIVE OR ADMINISTRATIVE ORDERS OR DECLARATIONS OR OTHERWISE, EVEN IF
MICROHARD SYSTEMS INC. HAS BEEN ADVISED OR OTHERWISE HAS KNOWLEDGE OF THE
POSSIBILITY OF SUCH DAMAGES AND TAKES NO ACTION TO PREVENT OR MINIMIZE SUCH
DAMAGES. IN THE EVENT THAT REGARDLESS OF THE WARRANTY DISCLAIMERS AND HOLD
HARMLESS PROVISIONS INCLUDED ABOVE MICROHARD SYSTEMS INC. IS SOMEHOW HELD
LIABLE OR RESPONSIBLE FOR ANY DAMAGE OR INJURY, MICROHARD SYSTEMS INC.'S LIABILITY
FOR ANYDAMAGES SHALL NOT EXCEED THE PROFIT REALIZED BY MICROHARD SYSTEMS INC.
ON THE SALE OR PROVISION OF THE HARDWARE TO THE CUSTOMER.
Proprietary Rights
The Buyer hereby acknowledges that Microhard Systems Inc. has a proprietary interest and intellectual property rights in the
Hardware, Software and/or Products. The Purchaser shall not (i) remove any copyright, trade secret, trademark or other evidence
of Microhard Systems Inc.’s ownership or proprietary interest or confidentiality other proprietary notices contained on, or in, the
Hardware, Software or Products, (ii) reproduce or modify any Hardware, Software or Products or make any copies thereof, (iii)
reverse assemble, reverse engineer or decompile any Software or copy thereof in whole or in part, (iv) sell, transfer or otherwise
make available to others the Hardware, Software, or Products or documentation thereof or any copy thereof, except in accordance
with this Agreement.
ii
N920 Operating Manual
n920 Regulatory Requirements
PLEASE READ THIS SECTION CAREFULLY
WARNING:
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 23 cm or
more should be maintained between the antenna of this device and persons during device operation. To
ensure compliance, operations at closer than this distance is not recommended. The antenna used for this
transmitter must not be co-located in conjunction with any other antenna or transmitter.
WARNING:
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received including interference that may cause undesired
operation.
WARNING:
Changes or modifications not expressly approved by Microhard Systems Inc. could void the user’s authority
to operate the equipment. This device has been tested with MMCX and Reverse Polarity SMA connectors
with the antennas listed in Appendix A When integrated in OEM products, fixed antennas require
installation preventing end-users from replacing them with non-approved antennas. Antennas not listed in
the tables must be tested to comply with FCC Section 15.203 (unique antenna connectors) and Section 15.247
(emissions).
WARNING:
MAXIMUM EIRP
FCC Regulations allow up to 36 dBm equivalent isotropically radiated power (EIRP). Therefore, the sum
of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36 dBm.
WARNING:
EQUIPMENT LABELING
The FCC and IC numbers depend on the model of the radio module. Do NOT use the Marketing
Name of the product but the Model to distinguish the Certifications Numbers. This device has
been modularly approved. The manufacturer, product name, and FCC and Industry Canada
identifiers of this product must appear on the outside label of the end-user equipment.
SAMPLE LABEL REQUIREMENT for Model: n920:
Contains:
FCC ID: NS908P24
IC : 3143A-08P24
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received including interference that may cause
undesired operation.
iii
Contents
Warranty ....................................................................................................................................................................... ii
Warranty Diclaims........................................................................................................................................................ ii
Indemnification............................................................................................................................................................. ii
Proprietary Rights......................................................................................................................................................... ii
n920 Regulatory Requirements ................................................................................................................................... iii
CONTENTS .............................................................................................................................................................. IV
2.
GENERAL ...........................................................................................................................................................1
2.0
2.1
3.
PRODUCT OVERVIEW ........................................................................................................................................................ 1
OUTPUT POWER LEVEL ..................................................................................................................................................... 2
INSTALLATION.................................................................................................................................................4
3.0
3.1
3.2
OVERVIEW ....................................................................................................................................................................... 4
ESTIMATING THE GAIN MARGIN ....................................................................................................................................... 4
ANTENNAS AND CABLING ................................................................................................................................................. 6
3.2.1 ........................................................................................................................Internal Cabling
...............................................................................................................................................................................6
3.2.2 ............................................................Installing External Cables, Antennas and Lightning Arrestors
...............................................................................................................................................................................7
iv
N920 Operating Manual
2. General
2.0 Product Overview
The N920 is a high-performance embedded wireless data transceiver.
Operating in the 902 - 928 MHz ISM band, this frequency-hopping spreadspectrum module is capable of providing reliable wireless data transfer
between almost any type of equipment which uses an asynchronous serial
interface. The small-size and superior RF performance of this module make
it ideal for many applications.
While a pair of N920 modules can link two terminal devices (“point-topoint” operation); multiple modules can be used together to create a
network of various topologies, including “point-to-multipoint” and
“repeater” operation. Multiple independent networks can operate
concurrently, so it is possible for unrelated communications to take place in
the same or a nearby area without sacrificing privacy or reliability.
1.1 Features
Key features of the N920 include:
transmission within a public, license-exempt band of the radio
spectrum1 – this means that it can be used without access fees
(such as those incurred by cellular airtime).
a serial I/O data port with handshaking and hardware flow
control, allowing the N920 to interface directly to any
equipment with an asynchronous serial interface.
ease of installation and use – the N920 module uses a subset
of standard AT style commands, very similar to those used by
traditional telephone line modems.
all units in a system are physically identical, and can be
configured as a master, repeater or slave using the AT
command set. No hardware modifications are required
Selectable pseudo-random hopping patterns, intelligently
designed to offer the possibility of separately operating
multiple networks while providing security, reliability and
high tolerance to interference.
32-bit of CRC error detection and auto re-transmit to provide
accuracy and reliability of data.
902-928 MHz, which is license-free within North America; may need to be factoryconfigured differently for some countries.
TDMA (time division multiple access) support, allowing
multi-slave access in point-to-point mode.
roaming ability, allowing repeaters and slaves to resynchronize with a new master if the synchronization pulse
from the original master is lost.
While the typical application for the N920 is to provide a short- to midrange wireless communications link between DTEs, it can be adapted to
almost any situation where an asynchronous serial interface is used and data
intercommunication is required.
2.1 Output Power Level
The Output Power Level determines at what power the N920 transmits.
The N920’s sensitive receiver can operate with very low power levels, so it
is recommended that the lowest power necessary is used; using excessive
power contributes to unnecessary “RF pollution”.
Ideally, you should test the communications performance between units
starting from a low power level and working upward until the RSSI is
sufficiently high and a reliable link is established. The conditions will vary
widely between applications, the output power settings can be calculated
based on following information.
•
Transmitter antenna gain
•
Cable loss
•
Equivalent Isotropically Radiated Power (EIRP) requirement by FCC
Regulations
Power Setting = 36 – Antenna Gain – Cable Loss
The power setting must be no more than the above calculation value. Any
higher is a violation of FCC rules. See IMPORTANT warning below.
Table 1 Output Power
Power Setting
(dBm)
Approx. Output Power
(mW)
20
21
22
23
24
25
26
27
28
29
30
100
125
160
200
250
320
400
500
630
800
1000
The power setting must be no more than the above calculation value. Any
higher is a violation of FCC rules. See IMPORTANT warning below:
OEMs must take precaution to satisfy the maximum RF exposure and EIRP
maximum limits in accordance with the compliance limits herein.
The conducted power is continuously variable from 0.001 to 1.0 Watt. For
operations in mobile RF exposure conditions, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 23
cm from all persons with the maximum allowable antenna gains of 1.5 dBi
(Quarter Wave), 2 dBi (Rubber Ducky), 5.15 dBi (Transit), 8.15 dBi (Omni
Directional), 12.5 dBi (Patch) and 14.15 dBi (Yagi). For antennas with the
gains greater 6dBi, the appropriate cable with loss in dB shall be used in
order to maintain the EIRP (conducted powerin dBm + antenna gain in dBi
cable loss in dB) less than 36 dBm. Antenna(s) used for this transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter.
3. Installation
3.0 Overview
The N920 complies with FCC part 15 at the modular level for operation in
the license-free 902-928 MHz ISM band. This chapter provides guidelines
for installing and deploying equipment which incorporates the N920
module.
3.1 Estimating the Gain Margin
Successful communication between N920 modules is dependent on three
main factors:
•
System Gain
•
Path Loss
•
Interference
System gain is a calculation in dB describing the performance to be
expected between a transmitter-receiver pair. The number can be calculated
based on knowledge of the equipment being deployed. The following four
factors make up a system gain calculation:
1.
Transmitter power
2.
Transmitter gain (transmitting antenna gain minus cabling loss between
the transmitting antenna and the N920 module)
3.
Receiver gain (Receiving antenna gain minus cabling loss between the
receiving antenna and the module)
4.
Receiver sensitivity (Specified as -108dBm on the N920 module)
In the following illustration, the transmitting antenna has a gain of 6 dB,
and the receiving antenna has a gain of 3 dB. The cable loss between the
module and the antenna is 2 dB on both the transmitting and receiving side.
Cable Loss = 2 dB
Antenna Gain = 6 dB
Cable Loss = 2 dB
Antenna Gain = 3 dB
Transmitter
Receiver
30 dBm
Output Power
Sensitivity =
-105 dBm
Figure 1 Gain Calculation
The power level has been set to 30dBm (1W) on the transmitter, and the
receiver sensitivity for the N920 is -108dBm.
System gain would be calculated to be:
30 - 2 + 6 + 3 - 2 + 108 = 143 dB.
Base Height (m)
Mobile
Height
(m)
Distance (km)
Figure 2 System Deploying
When deploying your system, care must be taken to ensure the path loss
(reduction of signal strength from transmitter to receiver in dB) between
equipment does not exceed the system gain (140 dB in the above example).
It is recommended to design for a gain margin of at least 20 dB to ensure
reliable communication. Gain margin is the difference between system gain
and path loss. Referring to the same example, suppose the path loss is 100
dB, the gain margin would be 40 dB, which is more than adequate for
reliable communication.
Path loss is a very complicated calculation which mainly depends on the
terrain profile, and the height of the antennas off the ground.
The following table provides path loss numbers for varying antenna heights
and antenna separation: These numbers are real averages taken from rural
environments. They do not apply to urban, non-line-of-sight environments.
Table 2 Path Loss
n920 Operating Manual
Distance
(km)
Base Height
(m)
Mobile Height
(m)
Path Loss
(dB)
15
2.5
116.5
30
2.5
110.9
15
2.5
124.1
15
117.7
15
10
105
16
15
2.5
135.3
16
15
128.9
16
15
10
116.2
16
30
10
109.6
16
30
122.4
16
30
2.5
128.8
Once the equipment is deployed, you can verify the signal strength by
entering into Command Mode and reading Register S123. This register
provides the average signal strength in dBm. The minimum strength for
communication is roughly -108dBm. For consistent reliable
communication, you should try to deploy the equipment such that signal
strength exceeds -95dBm.
3.2 Antennas and Cabling
This section describes the recommended procedure for installing cabling
and antennas for use with the N920 module.
3.2.1
Internal Cabling
The most common method for installing the module is to run a cable from
the module’s MMCX connector to a reverse TNC bulkhead connector on
the chassis of the equipment as shown in Figure 3. This cable can be
purchased from Microhard Systems.
Reverse TNC Connector
RG316 Cable
with MMCX
male
connector
and Reverse TNC
bulkhead
connector
N920
MMCX female
Figure 3 Suggested Internal Cabling
Cable losses are negligible for the short piece used within the chassis.
Additional losses up to 0.5 dB may be present in the MMCX and Reverse
TNC connections.
n920 Operating Manual
3.2.2
WARNING:
To satisfy FCC RF exposure
requirements for mobile
transmitting devices, a separation
distance of 23 cm or more should
be maintained between the
antenna of this device and
persons during device operation.
To ensure compliance, operations
at closer than this distance is not
recommended. The antenna used
for this transmitter must not be
co-located in conjunction with
any other antenna or transmitter.
Installing External Cables, Antennas and Lightning
Arrestors
Never work on an antenna system when there is lightning in the area.
Direct human contact with the antenna is potentially unhealthy when the
N920 is generating RF energy. Always ensure that the N920 equipment is
powered down during installation. At all times a distance of 23 cm must be
maintained between the antenna and any person when the device is in
operation.
Surge Arrestors
The most effective protection against lightning is to install two lightning
(surge) arrestors, one at the antenna, the other one at the interface with the
equipment.
The surge arrestor grounding system should be fully
interconnected with the transmission tower and power grounding systems to
form a single, fully integrated ground circuit. Typically, both ports on surge
arrestors are N-female.
External Filter
WARNING:
Direct human contact with the
antenna is potentially unhealthy
when the N920 is generating RF
energy. Always ensure that the
N920 equipment is powered
down during installation.
WARNING:
Never work on an antenna
system when there is lightning in
the area.
Although the N920 is capable of filtering out RF noise in most
environments, there are circumstances that require external filtering.
Paging towers and cellular base stations in close proximity to the N920
antenna can desensitize the receiver. Microhard Systems’ external cavity
filter eliminates this problem. The filter has two N-female ports and should
be connected in line at the interface to the RF equipment.
Weatherproofing
Type N and RTNC connectors are not weatherproof. All connectors should
be taped with rubber splicing tape (weatherproofing tape), and then coated
with a sealant.
Cabling
The following coax cables are recommended:
Table 3 Cable Loss
Cable
Loss (dB/100ft)
LMR 195
10.7
LMR 400
3.9
LMR 600
2.5
Factors to take into consideration when choosing a cable are:
n920 Operating Manual
•
price;
•
bend radius limitations (the lower performance cables generally can
bend more sharply)
•
performance requirements; and,
•
distance between the equipment and the antenna.
WARNING:
MAXIMUM EIRP
FCC and IC Regulations allow
up to 36dBm effective
isotropically radiated power
(EIRP). Therefore, the sum of
the transmitted power (in dBm),
the cabling loss and the antenna
gain cannot exceed
36 dBm with respect to the
isotropic radiator.
WARNING:
The N920 can only be used with
any antennas listed in Appendix
A.
WARNING:
Be careful with dBi vs dBd gains
on antenna specifications.
Antenna manufactures may not
clearly indicate the gain on the
antenna if it is dBd or dBi. Note
1dBd = 2.15dBi.
When installing the cable, always begin fastening at the top near the
antenna connector/surge arrestor. The cable must be supported at the top
with a hose clamp or wrap lock, and at 5 ft intervals down the length of the
tower. Over-tightening the fasteners will dent the cable and reduce
performance. If properly grounded surge arrestors are not installed at both
the top and the bottom of the cable, then the cable should be grounded to
the tower at these locations using a cable grounding kit. If the tower is nonconductive, then a separate conductor, physically separate from the cable,
should be run down the tower.
Antenna
Before choosing an antenna, you should have some knowledge of the path
loss and the topology of the equipment. If the equipment is in a fixed
location and is to communicate with only one other unit also in a fixed
location, then a Yagi antenna is suitable. Choose a Yagi with enough gain
to ensure adequate gain margin. When deploying the Yagi, point the
antenna towards the intended target, ensuring the antenna elements are
perpendicular to the ground for vertical polarization.
In applications where there are multiple units that you must communicate
with or units, which are in motion, you may select an Omni-directional
antenna with appropriate gain.
See appendix A for a list of approved antennas that can be used with
the N920 radio modem. If you require another type of antenna please
contact Microhard Systems Inc. The N920 CANNOT be used with any
antenna that does not appear in Appendix A.
Microhard Systems Inc. can provide you with approved antennas to ensure
FCC and Industry Canada compliance.
FCC Regulations allow up to 36dBm effective isotropically radiated
power (EIRP). Therefore, the sum of the transmitted power (in dBm),
the cabling loss and the antenna gain cannot exceed 36dBm with
respect to the isotropic radiator.
EIRP is calculated as follows:
EIRP = Tx Power(dBm) - Cable/Connector Loss(dB) + Ant Gain(dBi)
Antenna Gains must be in dBi when calculating the 36dBm EIRP limit.
1dBd = 2.15dBi
Use the guidelines in the previous section for calculating cable and
connector losses. If cabling and connector losses are 2 dB, then the
maximum allowable gain of the antenna will be 8 dB.
Examples of Antenna and Power settings to maintain 36dBm EIRP
Antenna
Power Level
Minimum Cable / Loss
EIPR
8.15 dBi Omni
30dBm
25 feet LMR195 / 2.675dB
35.475dBm
12.5 dBi Patch
23dBm
10 feet LMR195 / 1.07dB
34.43dBm
14.15 dBi Yagi
21dBm
10 feet LMR400 / 0.39dB
34.76dBm
n920 Operating Manual
Examples:
FCC and Industry Canada Regulations allow up to 36dBm effective
isotropically radiated power (EIRP). Therefore, the sum of the
transmitted power (in dBm), the cabling loss and the antenna gain
cannot exceed 36dBm with respect to the isotropic radiator.
Example 1)
What is the maximum power the N920 can be set to comply with FCC
and IC given the following equipment given a Rubber Ducky Ant Gain
2dBi and no cable or connectors in the system?
Max EIRP 36dBm
Max TX power = EIRP – Ant Gain(dBi) + Cable/Connector loss (dB)
Ant Gain dBi = 2dBi
Max TX power = 36dBm – 2dBi + 0dB = 34dBm
We can set the modem to the maximum power setting of 30dBm.
Example 2)
What is the maximum power the N920 can be set to comply with FCC
and IC given the following equipment given a Yagi Ant Gain 12dBd
and cable and connector loss of 4.5 dB?
Max EIRP 36dBm
Max TX power = EIRP – Ant Gain(dBi) + Cable/Connector loss (dB)
Ant Gain dBi = Ant Gain dBd + 2.15 dB
Yagi Gain (dBi) = 12 + 2.15 = 14.15dBi
Max TX power = 36dBm – 14.15dB + 4.5dB = 26.35dBm
We must round down
Hence Max TX power = 26dBm
Example 3)
What is the maximum power the N920 can be set to comply with FCC
and IC given the following equipment given a Omni Ant Gain 6dBd
and cable and connector loss of 2.5 dB?
Max EIRP 36dBm
Max TX power = EIRP – Ant Gain(dBi) + Cable/Connector loss (dB)
Ant Gain dBi = Ant Gain dBd + 2.15 dB
Omni Gain (dBi) = 6 + 2.15 = 8.15dBi
Max TX power = 36dBm – 8.15dB + 2.5dB = 30.35dBm
Hence Max TX power = 30dBm
n920 Operating Manual
A. Approved Antennas
Group
Part Number
Description
MHS031010
<1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Right Angle
MHS031020
<1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Straight
MHS031030
<1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Right Angle MHS
MHS031040
<1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Straight MHS
Quarter Wave
MHS031050
<1.5dBi, 900MHz 1/4 Wave Antenna MMCX Right Angle MHS
MHS031060
<1.5dBi, 900MHz 1/4 Wave Antenna Reverse SMA Straight
MHS031000
2dBi, 900MHz Rubber Ducky Antenna RPTNC Swivel
Rubber Ducky
MHS031070
2dBi, 900MHz Rubber Ducky Antenna Reverse SMA Swivel
MHS031080
2dBi, 900MHz Rubber Ducky Antenna Reverse SMA Straight
MHS031210
3dBd, 900 MHz Transit Antenna with Ground Plane
Transit Antennas
MHS031220
3dBd, 900MHz Transit Antenna No Ground Plane
MHS031230
3dBd, 900MHz Transit Antenna Permanent Mount GP
MHS031240
3dBd, 900MHz Transit Antenna Permanent Mount NGP
Mounts for Transit Antennas have a RPTNC Pigtail
Yagi Antennas
MHS031311
6dBd, 900MHz Yagi Directional Antenna Antenex, RPTNC Pigtail
MHS031431
6.5dBd, 900MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail
MHS031501
9dBd, 900MHz Yagi Directional Antenna Antenex, RPTNC Pigtail
MHS031441
10dBd, 900 MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail
MHS031451
11dBd, 900 MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail
MHS031401
12dBd, 900MHz Yagi Directional Antenna Antenex, RPTNC Pigtail
MHS031411
12dBd, 900MHz Yagi Directional Antenna Bluewave, RPTNC Pigtail
MHS031440
8dBi 900 MHz Patch Antenna, RPTNC Pigtail
MHS031430
12.5dBi 900 MHz Patch Antenna, RPTNC Pigtail
Patch Antennas
Omni Directional
MHS031251
3dBd, 900MHz Omni Directional Antenna Antenex, RPTNC Pigtail
MHS031461
3dBd, 900 MHz Omni Directional Antenna Bluewave, RPTNC Pigtail
MHS031321
6dBd, 900MHz Omni Directional Antenna Antenex, RPTNC Pigtail
MHS031471
6dBd, 900 MHz Omni Directional Antenna Bluewave, RPTNC Pigtail
WARNING:
Changes or modifications not expressly approved by Microhard Systems Inc. could void the user’s authority to operate
the equipment. This device has been tested with MMCX connectors with the antennas listed in Appendix A When
integrated in OEM products, fixed antennas require installation preventing end-users from replacing them with nonapproved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique
antenna connectors) and Section 15.247 (emissions). Please Contact Microhard Systems Inc. if you need more
information.
Industry Canada: This device has been designed to operate with the antennas listed below, and having a maximum gain
of 14.2 dBi. Antennas not included in this list or having a gain greater than 14.2 dBi are strictly prohibited for use with
this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than
that required for successful communication. This Class B digital apparatus complies with Canadian ICES-003.
10
n920 Operating Manual

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 5.0 (Windows)
Create Date                     : 2008:05:13 03:42:44Z
Modify Date                     : 2008:05:13 13:44:47-04:00
Metadata Date                   : 2008:05:13 13:44:47-04:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Creator                         : hshenouda
Title                           : Microsoft Word - n920FSmanualREV0.40.FCC.doc
Document ID                     : uuid:ce753814-f197-4157-a738-6cfe5c004b3d
Instance ID                     : uuid:1fb145b4-a722-4c5a-ad82-de886c4557ed
Page Count                      : 14
Author                          : hshenouda

EXIF Metadata provided by EXIF.tools