Microlab Electronics R4B Soundbar User Manual Statement

Download:
Mirror Download [FCC.gov]
Document ID	4191540
Application ID	xfgavq8HEpaLAM2CWTDlEw==
Document Description	User Manual-Statement
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	85.54kB (1069289 bits)
Date Submitted	2019-03-06 00:00:00
Date Available	2019-03-06 00:00:00
Creation Date	2019-01-11 13:38:09
Producing Software	macOS Version 10.14.1 (Build 18B75) Quartz PDFContext
Document Lastmod	2019-01-11 13:38:09
Document Title	User Manual-Statement
Document Creator	Adobe InDesign CC 2015 (Macintosh)

R-4B II
IMPORTANT SAFETY INSTRUCTIONS
Language
IMPORTANT SAFETY INSTRUCTIONS!
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. DO NOT defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the
manufacturer.
12. USE ONLY with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when
unused for long periods of time.
14. REFER all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
15. DO NOT expose this apparatus to dripping or splashing
and ensure that no objects filled with liquids, such as
vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC
Mains, disconnect the power supply cord plug from the
AC receptacle.
19. Do not install this equipment in a confined or building-in
space such as a book case or similar unit, and remain a well
ventilation conditions at open site. The ventilation should
not be impeded by covering the ventilation openings with
items such as newspaper, table-cloths, curtains etc.
20. The apparatus is intended to be used in moderate climates.
This equipment is a Class II or double insulated
electrical appliance. It has been designed in such a way
that it does not require a safety connection to electrical earth.
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
polarity. Remove batteries from products that are not in use
for extended periods of time. Store batteries in a dry place.
WARNING: Batteries (battery pack or batteries installed)
shall not be exposed to excessive heat such as sunshine, fire
or the like.
WARNING: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
WARNING: Do not recharge non-rechargeable batteries.
WARNING: Avoid exposure to extreme heat or cold.
Please dispose of any used batteries properly, following any
local regulations. Do not incinerate.
WARNING: Do Not Open! Risk of Electrical Shock. Voltages
in this equipment are hazardous to life. No user-serviceable
parts inside. Refer all servicing to qualified service personnel.
Place the equipment near a main power supply outlet and make
sure that you can easily access the power breaker switch.
WARNING: This product is intended to be operated ONLY from
the AC Voltages listed on the back panel or included power
supply of the product. Operation from other voltages other
than those indicated may cause irreversible damage to the
product and void the products warranty. The use of AC Plug
Adapters is cautioned because it can allow the product to be
plugged into voltages in which the product was not designed
to operate. If the product is equipped with a detachable
power cord, use only the type provided with your product or
by your local distributor and/or retailer. If you are unsure
of the correct operational voltage, please contact your local
distributor and/or retailer.
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low
Voltage Directive 2006/95/EC; European Union EMC Directive
2004/108/EC; European Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EC; European Union
WEEE Directive 2002/96/EC; European Union Eco-Design Directive 2009/125/EC; European Union Registration, Evaluation,
Authorization and Restriction of Chemicals (REACH) Directive
2006/121/EC; European Union Radio and Telecommunications
Terminal Equipment (R&TTE) Directive 1999/5/EC.
This product contains batteries that are covered under the
2006/66/EC European Directive, which cannot be disposed of
with normal household waste. Please follow local regulations.
You may obtain a free copy of the Declaration of Conformity
by contacting your dealer, distributor, or Klipsch Group, Inc.’s
worldwide headquarters. Contact information can be found
here: http://www.klipsch.com/Contact-Us
WEEE NOTICE
Note: This mark applies only to countries within the European
Union (EU) and Norway.
This appliance is labeled in accordance with European
Directive 2002/96/EC concerning waste of electrical
and electronic equipment (WEEE). This label indicates
that this product should not be disposed of with household
waste. It should be deposited at an appropriate facility to
enable recovery and recycling.
FCC AND CANADA EMC COMPLIANCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Approved under the verification provision of FCC Part 15 as a
Class B Digital Device.
Caution: Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate
this device.
Caution: To comply with the limits of the Class B digital device,
pursuant to Part 15 of the FCC Rules, this device is to comply
with Class B limits. All peripherals must be shielded and
grounded. Operation with non-certified peripherals or nonshielded cables my result in interference to radio or reception.
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B) Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du Canada.
WIRELESS TRANSMITTER COMPLIANCE INFORMATION
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
Le terme «IC:» avant le numéro de certification radio signifie
seulement que les spécifications techniques d’Industrie
Canada ont été respectées.
This device complies with Industry Canada’s licence-exempt
RSSs. Operation is subject to the following two conditions:(1)
This device may not cause interference; and(2) This device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This equipment complies with FCC and IC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any
other antenna or transmitter.
Cet appareil est conforme à FCC et IC l’exposition aux
rayonnements limites fixées pour un environnement non
contrôlé. Cet appareil doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur et votre corps.
Cet transmetteur ne doit pas être co-situé ou opérant en
liaison avec toute autre antenne ou transmetteur.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : XMP Core 5.4.0
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Metadata Date                   : 2015:07:29 08:55:36-04:00
Create Date                     : 2015:07:29 08:55:33-04:00
Modify Date                     : 2015:07:29 08:55:36-04:00
Format                          : application/pdf
Original Document ID            : xmp.did:4F7E61FD212068118A6DF9B7543F7449
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Parameters              : from application/x-indesign to application/pdf
History Changed                 : /
History When                    : 2015:07:29 08:55:33-04:00
History Action                  : converted
Instance ID                     : uuid:53d63456-e7d0-cb43-82b3-7a0892a3ed86
Document ID                     : xmp.id:da458bb3-ef6c-4ea6-ad73-130697d5428b
Derived From Rendition Class    : default
Derived From Document ID        : xmp.did:f940971b-b2cf-4aa3-be7d-e0f923e223cc
Derived From Instance ID        : xmp.iid:8d6056e3-163f-4fe1-b629-262ee360da5e
Derived From Original Document ID: xmp.did:4F7E61FD212068118A6DF9B7543F7449
Rendition Class                 : proof:pdf
Trapped                         : False
Producer                        : Adobe PDF Library 15.0
Page Count                      : 8
Creator                         : Adobe InDesign CC 2015 (Macintosh)

EXIF Metadata provided by EXIF.tools