MINI Hawk High Performance Imager User's Manual Minihawkmanual
2011-04-13
: Microscan Minihawkmanual minihawkmanual ceb38a48-6b4d-4573-8780-cb34f81c348c _att
Open the PDF directly: View PDF
Page Count: 380 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- MINI Hawk High Performance Imager User’s Manual
- Table of Contents
- About the MINI Hawk High Performance Imager
- MINI Hawk Communications
- Warning and Caution Summary
- Statement of Agency Compliance
- Statement of RoHS Compliance
- 1 Quick Start
- Step 1 — Check Hardware
- Step 2 — Connect the System
- Step 3 — Position Imager and Symbol
- Step 4 — Install ESP
- Step 5 — Select Model
- Step 6 — Select Protocol and Connect
- Step 7 — Locate the Symbol in the Field of View
- Step 8 — Calibrate
- Step 9 — Test Read Rate
- Step 10 — Configure the Imager in ESP
- Step 11 — Save Configuration in ESP
- 2 Using ESP
- 3 Communications
- Communications by ESP
- Communications Serial Commands
- Host Port Connections
- Host Port Protocol
- ACK/NAK Options
- Polling Mode Options
- RS-422 Status
- Auxiliary Port Connections
- Auxiliary Port System Data Status
- Daisy Chain Autoconfigure
- Response Timeout
- LRC Status
- Protocol Configuration Examples
- USB HID Interface
- ASCII Character Entry Modifier
- Preamble
- Postamble
- 4 Calibration
- 5 Read Cycle
- Read Cycle by ESP
- Read Cycle Serial Commands
- Read Cycle Setup
- Multisymbol
- Trigger Mode and Filter Duration
- External Trigger Polarity
- Serial Trigger
- Start Trigger Character (Non-Delimited)
- Stop Trigger Character (Non-Delimited)
- End of Read Cycle
- Capture Mode
- Capture Timing
- Image Processing Timeout
- Image Storage
- Minimum Good Reads
- Setting Up the Imager for EZ Trax
- 6 Symbologies
- 7 I/O Parameters
- I/O Parameters by ESP
- I/O Parameters Serial Commands
- Symbol Data Output
- No Read Message
- Read Duration Output
- Output Indicators
- Beeper
- LED Configuration
- Serial Verification
- EZ Button
- EZ Button Modes
- Configurable Output 1
- ISO/IEC 16022 Symbol Quality Output 1
- Diagnostics Output 1
- Configurable Output 2
- Trend Analysis Output 2
- ISO/IEC 16022 Symbol Quality Output 2
- Diagnostics Output 2
- Configurable Output 3
- Trend Analysis Output 3
- ISO/IEC 16022 Symbol Quality Output 3
- Diagnostics Output 3
- Power On/Reset Counts
- Time Since Reset
- Service Message
- Frame Information
- Image Output
- Database Identifier Output
- Quality Output
- Configuring EZ Trax Output
- 8 Symbol Quality
- 9 Matchcode
- 10 Camera and IP Setup
- Camera and IP Setup by ESP
- Camera and IP Setup Serial Commands
- Video
- Evaluation
- Calibration
- Window of Interest
- Configuration Database
- Dynamic Setup
- X-Mode™
- Pixel Sub-Sampling
- Camera Settings
- Camera Settings (3 Megapixel)
- Focal Distance
- Focal Distance (3 Megapixel)
- Focal Distance Table (Read-Only)
- Focal Distance Table (Read-Only) (3 Megapixel)
- Increment Focus Position
- Decrement Focus Position
- Increment Focus Position (3 Megapixel)
- Decrement Focus Position (3 Megapixel)
- Illumination Brightness
- Color Filter
- Skew Correction
- Morphological Pre-Processing
- Morphological Operation and Operator Size
- 11 Configuration Database
- 12 Terminal
- 13 Utilities
- 14 Output Format
- Appendices
- Appendix A — General Specifications
- Appendix B — Electrical Specifications
- Appendix C — Serial Configuration Commands
- Appendix D — Communications Protocol
- Appendix E — ASCII Table
- Appendix F — Interface Standards
- Appendix G — Operational Tips
- Appendix H — Using an External Trigger
- Appendix I — USB-to-Serial Virtual COM Port Driver
- Appendix J — MINI Hawk Image Output
- Appendix K — Glossary of Terms