MS 4 Imager User's Manual Ms4manual
2010-05-18
: Microscan Ms4Manual ms4manual bfd67ff5-e080-4103-8ffb-738df1f47de2 _att
Open the PDF directly: View PDF
Page Count: 390 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- MS-4 Imager User’s Manual
- Table of Contents
- About the MS-4 Imager
- About This Manual
- Highlighting
- Host Communications
- Warning and Caution Summary
- Statement of Agency Compliance
- Statement of RoHS Compliance
- 1 Quick Start
- Step 1 - Check Required Hardware
- Step 2 - Connect the System
- Step 3 - Position Imager and Symbol
- Step 4 - Install ESP
- Step 5 - Select Model
- Step 6 - Select Communications Protocol
- Step 7 - Locate the Symbol in the FOV
- Step 8 - Calibrate Settings
- Step 9 - Test Read Rate
- Step 10 - Configure the Imager in ESP
- Step 11 - Make Menu Changes and Save in ESP
- 2 Using ESP
- 3 Communications
- Communications by ESP
- Communications Serial Commands
- Host Port Connections
- Host Port Protocol
- ACK / NAK Options
- Polling Mode Options
- RS-422 Status
- Auxiliary Port Connections
- Auxiliary Port System Data Status
- Daisy Chain Autoconfigure
- Response Timeout
- LRC Status
- Protocol Configuration Examples
- USB HID Interface
- ASCII Character Entry Modifier
- Preamble
- Postamble
- 4 Calibration
- 5 Read Cycle
- Read Cycle by ESP
- Read Cycle Serial Commands
- Read Cycle Setup
- Multisymbol
- Trigger Mode and Duration
- External Trigger Polarity
- Serial Trigger
- Start Trigger Character (Non-Delimited)
- Stop Trigger Character (Non-Delimited)
- End of Read Cycle
- Capture Mode
- Capture Timing
- Image Processing Timeout
- Image Storage
- Minimum Good Reads
- Setting Up the Imager for EZ Trax
- 6 Symbologies
- 7 I/O Parameters
- I/O Parameters by ESP
- I/O Parameters Serial Commands
- Symbol Data Output
- No Read Message
- Bad Symbol Message
- No Symbol Message
- 1D / Stacked Symbology Qualification
- 2D Symbology Qualification
- Read Duration Output
- Output Indicators
- Beeper
- LED Configuration
- Serial Verification
- EZ Button
- EZ Button Modes
- Configurable Output 1
- Trend Analysis Output 1
- ISO/IEC 16022 Symbol Quality Output 1
- Diagnostic Output 1
- Configurable Output 2
- Trend Analysis Output 2
- ISO/IEC 16022 Symbol Quality Output 2
- Diagnostic Output 2
- Configurable Output 3
- Trend Analysis Output 3
- ISO/IEC 16022 Symbol Quality Output 3
- Diagnostic Output 3
- Power-On / Reset Counts
- Time Since Reset
- Service Message
- Frame Information
- Image Output
- Database Identifier Output
- Quality Output
- Configuring EZ Trax Output
- 8 Symbol Quality
- 9 Matchcode
- 10 Camera and IP Setup
- Camera and IP Setup by ESP
- Camera and IP Setup Serial Commands
- Video
- Evaluation
- Calibration
- Window of Interest
- Configuration Database
- Dynamic Setup
- Pixel Sub-Sampling
- Camera
- Focal Distance
- Focal Distance Table (Read-Only)
- IP Threshold
- Number of Symbols in Field of View
- Image Processing Timeout
- Damaged Symbol
- IP Mode
- Hollow Mode
- Mirrored Image
- Illumination Brightness
- Skew Correction
- 11 Configuration Database
- 12 Terminal
- 13 Utilities
- 14 Output Format
- Appendices
- Appendix A - General Specifications
- Appendix B - Electrical Specifications
- Appendix C - Serial Configuration Commands
- Appendix D - Communications Protocol
- Appendix E - ASCII Table
- Appendix F - Interface Standards
- Appendix G - Object Detector
- Appendix H - Operational Tips
- Appendix I - USB-to-Serial Virtual COM Port Driver
- Appendix J - Glossary of Terms
- Index