Microsoft 1491 802.11 b/g/n WLAN Module User Manual

Microsoft Corporation 802.11 b/g/n WLAN Module Users Manual

Users Manual

Model 1491 OEM Manual Page 1 of 2 Microsoft Corp. Model 1491 installation instructions General Guidelines The final end product user manual should NOT provide any instructions on how to remove or install this device. End Product Labelling The Final end product label must contain the following statement on the product label: For United States & Canada “This Device Contains FCC ID: C3K1491” ”This Device Contains IC: 3048A-1491” For Taiwan Notes for OEM Integrators This device is for use only in the Xbox console system for which it was designed, and installed during the console manufacturing process. The antenna must be installed such that 20 cm is maintained between the antenna and users. The transmitter module may not be co-located with any other transmitter or antenna. The transmitter module is approved using the FCC “unlicensed modular transmitter” approval method, therefore the module must only be used with the originally approved antennas. The end user should NOT be provided any instructions on how to remove or install the device. User Manual Statements The end product user manual must contain the following statements; For customers in Singapore For customers in Taiwan 低功率電波輻性電機管理辦法 第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使 用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發 現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾
Model 1491 OEM Manual Page 2 of 2 消費者保護法第二十四條第二項：「輸入之商品或服務，應附中文標示及說明書，其內容不得較原產地之標示及說明書簡略 For customers in Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003, CNR-Gen, et CNR-210 du Canada. Son fonctionnement est assujetti aux deux conditions suivantes : (1) Cet appareil ne peut pas provoquer d’interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement non désiré. To comply with IC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. For Customers in the United States "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.” A statement to caution the user that changes or modifications not expressly appproved by Microsoft could void the user’s authority to operate the equipment. (reference FCC Section 15.21) “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” (reference FCC Section 15.19(a)(3) ) “This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” (reference FCC Title 47 Section 15.105)

Navigation menu