Microsoft BH-220 Bluetooth Headset User Manual User Man QTLBH 220
Microsoft Mobile Oy Bluetooth Headset User Man QTLBH 220
User Man_QTLBH-220
Nokia Luna User Guide
Issue 1
Introduction
About your headset
With the Nokia Luna Bluetooth Headset, you can handle calls hands-free, even when
you are using two phones at the same time. Remove the headset from the cradle, and
it's instantly ready for use.
The surface of this product is nickel-free.
Warning:
This product may contain small parts. Keep them out of the reach of small children.
Parts of the product are magnetic. Metallic materials may be attracted to the product.
Do not place credit cards or other magnetic storage media near the product, because
information stored on them may be erased.
Read this user guide carefully before using the product. Also, read the user guide for
the device that you connect to the product.
For more information, go to www.nokia.com/support.
About Bluetooth connectivity
You can use Bluetooth to make a wireless connection to other compatible devices, such
as mobile devices.
Devices do not need to be in direct line-of-sight, but they must be within 10 metres (33
feet) of each other. The connection may be affected by obstructions such as walls or
other electronic devices.
This device is compliant with Bluetooth Specification 2.1 + EDR supporting the following
profiles: Headset Profile 1.1 and Hands-Free Profile 1.5. Check with the manufacturers
of other devices to determine their compatibility with this device.
2
Get started
Keys and parts
8
1Microphone
2Earpiece
3Charging indicator light
4Cradle
5Charger connector
6NFC area
7Bluetooth indicator light
8Multifunction key
Charge the battery
Before using the headset, you must charge the battery.
Warning:
Use only chargers approved by Nokia for use with this particular model. The use of any
other types may invalidate any approval or warranty, and may be dangerous. Use of
unapproved chargers may present a risk of fire, explosion, or other hazard.
1 Connect the charger to a wall outlet.
2 Place the headset in the cradle.
3 Connect the charger cable to the charger connector in the cradle. The red charging
indicator light switches off when the battery is fully charged.
4 Disconnect the charger from the cradle, then from the wall outlet.
When you unplug a charger, hold and pull the plug, not the cord.
The fully charged battery has power for up to 2 hours of talk time and up to 35 hours
of standby time. If you keep the headset in the cradle, the standby time is up to 2
months.
3
When the battery charge is low, you hear a voice prompt. In addition, a red indicator
light flashes and the headset beeps every 5 minutes. If you have deactivated voice
prompts, the headset beeps every 5 minutes.
Check the battery charge
With your headset switched on and connected to your phone, press the multifunction
key. A green light indicates a sufficient charge level. If the light is yellow, you may need
to recharge the battery soon. If the light is red, recharge the battery.
Switch the headset on or off
Switch on
Press the headset down to remove it from the cradle. The headset switches on, and a
green indicator light flashes once.
The headset connects to the last connected phone. If you have never paired the headset
with a phone, or you have cleared the pairings, pairing mode is activated.
Switch off
Place the headset in the cradle, and press down on the headset to lock it into place. The
headset switches off, and a red indicator light flashes once. All active calls and
connections are ended.
If not connected to a phone within 30 minutes, the headset switches off.
Tip: Don't have the cradle with you? To switch the headset off, press and hold the
multifunction key for 5 seconds. To switch the headset on, press the multifunction key.
Wear the headset
The headset comes with different sized earpads. Select the earpad that fits the best and
is the most comfortable for your ear. To change the earpad, gently pull the current
earpad from the earpiece, and push the new earpad into place.
Gently push the earpiece into your ear.
When you're not using your headset, keep it in the cradle. You can thread a wrist strap
through the holes in the cradle, and carry it with you easily.
Pair the device
Pair and connect the headset to your phone
Before using the headset, you must pair and connect it to a compatible phone.
4
You can pair your headset with 8 phones, but you can only connect it to a maximum of
2 phones at the same time.
With some phones, you may need to make the connection separately after pairing.
When the headset is connected to a phone, the Bluetooth indicator light flashes slowly.
Pair and connect the headset using NFC
With Near Field Communication (NFC), you can pair and connect your headset to your
compatible phone easily.
If the compatible phone supports NFC, activate its NFC feature, remove the headset from
the cradle, and touch the NFC area of the cradle with the NFC area of your phone. The
headset connects to the phone automatically.
You can also disconnect the headset using NFC. For details on NFC, see the user guide of
the phone.
If the phone does not support NFC, pair the headset manually.
Pair the headset manually
1 Make sure your headset is switched off and your compatible phone on.
2 If you have never paired the headset with a device, or you have cleared the pairings,
switch the headset on.
If you have previously paired your headset with another device, press and hold the
multifunction key for 5 seconds.
Pairing mode is activated, and a blue indicator light starts to flash quickly. Follow
the voice prompts.
3 Within 3 minutes, activate Bluetooth on the phone, and set it to search for Bluetooth
devices. For details, see the user guide of the phone.
4 On your phone, select the headset from the list of found devices.
5 If required, enter the passcode 0000.
In some devices, you may need to make the connection separately after pairing.
5
Pair and connect the headset to two phones
When you use the headset for the first time, it automatically pairs and connects to your
phone. You can also connect your headset to another phone, and manage calls from,
for example, both your personal and your work phones at the same time.
1 Make sure Bluetooth is activated on both phones.
2 To switch the headset off, press and hold the multifunction key for 5 seconds.
3 Press and hold the multifunction key for 5 seconds to activate pairing mode, and
pair the headset with the second phone.
4 Switch the headset off and back on. The headset connects to both phones.
Make calls
Make and receive calls
To make and receive calls using your headset, you need to connect it to your phone.
Make a call
Make a call in the normal way.
Answer a call
Remove the headset from the cradle.
End a call
Press the headset into the cradle, or press the multifunction key.
Reject a call
Press the headset into the cradle, or press the multifunction key twice.
Switch a call between your headset and phone
Press and hold the multifunction key for 2 seconds.
You can redial the last called number or use voice dialling, if your phone supports these
features with the headset.
Redial the last called number
When no call is in progress, press the multifunction key twice.
Use voice dialling
When no call is in progress, press and hold the multifunction key for 2 seconds, and
follow the instructions in the user guide of your phone.
6
Handle calls from two phones
If your headset is connected to two phones, you can handle calls from both at the same
time.
End an ongoing call, and answer a call on another phone
Press the multifunction key.
Put an ongoing call on hold, and answer a call on another phone
Press and hold the multifunction key for 2 seconds.
Switch between active and held calls
Press and hold the multifunction key for 2 seconds.
End an ongoing call, and activate a held call
Press the multifunction key.
If you redial or use voice dialling, the call is made on the phone you last had an active
call on with the headset.
Change the volume
Set the desired volume level on your connected phone. The selected volume level is
saved as the minimum volume level for that phone. The headset remembers the set
volume level for each connected phone separately.
Your headset adjusts the volume automatically according to the level of background
noise.
Settings
Deactivate voice prompts
1 To switch the headset off, press and hold the multifunction key for 5 seconds.
2 Press and hold the multifunction key for 5 seconds. Pairing mode is activated, and
a blue indicator light starts to flash quickly.
3 Press and hold the multifunction key for 2 seconds. You hear a voice prompt, and a
yellow indicator light flashes once.
Activate voice prompts
1 To switch the headset off, press and hold the multifunction key for 5 seconds.
2 Press and hold the multifunction key for 5 seconds. Pairing mode is activated, and
a blue indicator light starts to flash quickly.
3 Press and hold the multifunction key for 2 seconds. You hear a voice prompt, and a
green indicator light flashes once.
7
Clear the pairings
1 To switch the headset off, press and hold the multifunction key for 5 seconds.
2 Press and hold the multifunction key for 9 seconds. The headset beeps twice, and
the red and green indicator lights alternate.
3 When the headset switches on, pairing mode is activated. Follow the voice prompts.
Product and safety information
Battery and charger information
This device has an internal, nonremovable, rechargeable battery. Do not attempt to remove the battery from the device as you
may damage the device.
This device is intended for use when supplied with power from the following chargers: AC-16 . The exact charger model number
may vary depending on the type of plug. The plug variant is identified by one of the following: E, X, AR, U, A, C, K, or B. For
example, the model numbers for the charger can be, among others, AC-16C, AC-16U, AC-16X, etc. The charger model offered to
China mainland is AC-16C and the compatible cable is CA-179.
The battery can be charged and discharged hundreds of times, but it will eventually wear out.
Talk and standby times are estimates only. Actual times are affected by, for example, device settings, features being used,
battery condition, and temperature.
If the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and
reconnect it.
If the battery is completely discharged, it may take several minutes before the charging indicator is displayed.
When your charger is not in use, unplug it from the electrical plug and the device. Do not leave a fully charged battery connected
to a charger, as overcharging may shorten the battery’s lifetime. If left unused, a fully charged battery will lose its charge over
time.
Always keep the battery between 15°C and 25°C (59°F and 77°F). Extreme temperatures reduce the capacity and lifetime of the
battery. A device with a hot or cold battery may not work temporarily.
Do not dispose of batteries in a fire as they may explode. Dispose of batteries according to local regulations. Recycle when
possible. Do not dispose as household waste.
Use the charger for its intended purpose only. Improper use or use of unapproved chargers may present a risk of fire, explosion,
or other hazard, and may invalidate any approval or warranty. If you believe the charger is damaged, take it to a service centre
for inspection before continuing to use it. Never use a damaged charger. Only use the charger indoors.
Take care of your device
Handle your device, battery, charger and accessories with care. The following suggestions help you protect your warranty
coverage.
Handle your device, charger and accessories with care. The following suggestions help you protect your warranty coverage.
•Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode
electronic circuits. If your device gets wet, allow the device to dry.
•Do not use or store the device in dusty or dirty areas. Moving parts and electronic components can be damaged.
8
•Do not store the device in high temperatures. High temperatures can shorten the life of the device, damage the battery,
and warp or melt plastics.
•Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside
the device and damage electronic circuits.
•Do not attempt to open the device.
•Unauthorised modifications may damage the device and violate regulations governing radio devices.
•Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and mechanics.
•Only use a soft, clean, dry cloth to clean the surface of the device.
•Do not paint the device. Paint can clog moving parts and prevent proper operation.
Recycle
Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you
help prevent uncontrolled waste disposal and promote the recycling of materials. Check how to recycle your Nokia products at
www.nokia.com.cn/werecycle.
9
Copyright and other notices
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares that this Nokia Luna product is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/
phones/declaration_of_conformity/.
© 2011 Nokia. All rights reserved.
Nokia, Nokia Connecting People, and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia
Corporation. Nokia tune is a sound mark of Nokia Corporation. Other product and company names mentioned herein may be
trademarks or tradenames of their respective owners.
Reproduction, transfer, distribution, or storage of part or all of the contents in this document in any form without the prior
written permission of Nokia is prohibited. Nokia operates a policy of continuous development. Nokia reserves the right to make
changes and improvements to any of the products described in this document without prior notice.
The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either
express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose,
are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document
or withdraw it at any time without prior notice.
For the most current product information, please refer to www.nokia.com.cn.
To the maximum extent permitted by applicable law, under no circumstances shall Nokia or any of its licensors be responsible
for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
The availability of particular products may vary by region. Please check with your Nokia dealer for details. This device may
contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion
contrary to law is prohibited.
FCC/INDUSTRY CANADA NOTICE
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference
received, including interference that may cause undesired operation. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the
receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. NOTE: Changes or modifications not expressly approved by Nokia could void the user's authority to operate the
equipment.
/Issue 1 EN
10