Microsoft RM-223 GSM/WCDMA Cellular Phone with BT/WLAN User Manual P2954 en

Microsoft Mobile Oy GSM/WCDMA Cellular Phone with BT/WLAN P2954 en

UserManual.wiki >

RM-223 User Manual >

Contents

User Manaul

Connections72ConnectionsWireless LANYour device supports wireless local area network (wireless LAN). With wireless LAN, you can connect your device to the internet and compatible devices that have wireless LAN. For information about using your device with other compatible UPnP devices through wireless LAN, see ‘Home network with Gallery’, p. 52 and ‘Home network with music player’, p. 21.To use wireless LAN, a wireless LAN must be available in the location and your device must be connected to the wireless LAN.Some places, like France, have restrictions on the use of wireless LAN. Check with your local authorities for more information.Features using wireless LAN, or allowing such features to run in the background while using other features, increase the demand on battery power and reduce the battery life.Your device supports the following wireless LAN features:•IEEE 802.11b/g standard•Operation at a frequency of 2.4 GHz•Wired equivalent privacy (WEP) with keys up to 128 bits, Wi-Fi protected access (WPA), and 802.1x encryption methods. These functions can be used only if they are supported by the network.Wireless LAN connectionsTo use wireless LAN, you must create an internet access point (IAP) in a wireless LAN. Use the access point for applications that need to connect to the internet. See ‘Wireless LAN access points’, p. 73. Important: Always enable one of the available encryption methods to increase the security of your wireless LAN connection. Using encryption reduces the risk of unauthorized access to your data. A wireless LAN connection is established when you create a data connection using a wireless LAN internet access point. The active wireless LAN connection ends when you close the last application using the connection. To end all the connections simultaneously, see ‘Connection manager’, p. 77.You can use wireless LAN during a voice call or when packet data is active. You can only be connected to one wireless LAN access point device at a time, but several applications can use the same internet access point.P2954_en.book Page 72 Tuesday, July 3, 2007 2:51 PM

Connections75When the device is locked, you cannot use Bluetooth connectivity. See ‘Phone and SIM card’, p. 118 for more information on locking the device.SettingsPress , and select Tools > Bluetooth. When you open the application for the first time, you are asked to define a name for your device.Select from the following:Bluetooth—To connect wirelessly to another compatible device, first set Bluetooth connectivity On, then establish a connection. To switch off Bluetooth connectivity, select Off.My phone's visibility—To allow your device to be found by other devices with Bluetooth connectivity, select Shown to all. To set a time after which the visibility is set from shown to hidden, select Define period. To hide your device from other devices, select Hidden.My phone's name—Edit the name shown to other devices using Bluetooth wireless technology.Remote SIM mode—To enable another device, such as a compatible car kit enhancement, to use the SIM card in your device to connect to the network, select On. For more information, see ‘Remote SIM mode’, p. 77.Security tipsWhen you are not using Bluetooth connectivity, select Bluetooth > Off or My phone's visibility > Hidden. In this way, you can better control who can find your device with Bluetooth connectivity, and connect to it.Do not pair with or accept connection requests from an unknown device. In this way, you can better protect your device from harmful content.Send data using Bluetooth connectivitySeveral Bluetooth connections can be active at a time. For example, if you are connected to a compatible headset, you can also transfer files to another compatible device at the same time.For Bluetooth connectivity indicators, see ‘Essential indicators’, p. 74. Tip! To send text using Bluetooth connectivity, open Notes, write the text, and select Options > Send > Via Bluetooth.1Open the application where the item you want to send is stored. For example, to send an image to another compatible device, open Gallery.P2954_en.book Page 75 Tuesday, July 3, 2007 2:51 PM

Connections762Select the item and Options > Send > Via Bluetooth. Devices with Bluetooth connectivity within range start to appear on the display.Device icons: computer, phone, audio or video device, and other device.To interrupt the search, select Stop.3Select the device with which you want to connect.4If the other device requires pairing before data can be transmitted, a tone sounds, and you are asked to enter a passcode. See ‘Pair devices’, p. 76.5When the connection has been established, Sending data is shown. Tip! When searching for devices, some devices may show only the unique address (device address). To find the unique address of your device, enter the code *#2820# in the standby mode.Pair devicesTo pair with compatible devices and view your paired devices, in the Bluetooth application main view, press .Before pairing, create your own passcode (1-16 digits), and agree with the owner of the other device to use the same code. Devices that do not have a user interface have a factory-set passcode. The passcode is used only once.1To pair with a device, select Options > New paired device. Devices with Bluetooth connectivity within range start to appear on the display.2Select the device, and enter the passcode. The same passcode must be entered on the other device as well.Some audio enhancements connect automatically to your device after pairing. Otherwise, scroll to the enhancement, and select Options > Connect to audio device.Paired devices are indicated by in the device search. To set a device as authorized or unauthorized, scroll to a device, and select from the following options:Set as authorised—Connections between your device and this device can be made without your knowledge. No separate acceptance or authorization is needed. Use this status for your own devices, such as your compatible headset or PC, or devices that belong to someone you trust. indicates authorized devices in the paired devices view.Set as unauthorised—Connection requests from this device must be accepted separately every time.To cancel a pairing, scroll to the device, and select Options > Delete. If you want to cancel all pairings, select Options > Delete all.P2954_en.book Page 76 Tuesday, July 3, 2007 2:51 PM

Connections77Receive data using Bluetooth connectivityWhen you receive data through Bluetooth connectivity, a tone sounds, and you are asked if you want to accept the message. If you accept, is shown, and the item is placed in the Inbox folder in Messaging. Messages received through Bluetooth connectivity are indicated by . See ‘Inbox—receive messages’, p. 36.Remote SIM modeTo use the remote SIM mode with a compatible car kit enhancement, set Bluetooth connectivity on, and enable the use of the remote SIM mode with your device. See ‘Settings’, p. 75. Before the mode can be activated, the two devices must be paired and the pairing initiated from the other device. When pairing, use a 16-digit passcode, and set the other device as authorized. See ‘Pair devices’, p. 76. Activate the remote SIM mode from the other device.When remote SIM mode is on in your device, Remote SIM is displayed in the standby mode. The connection to the wireless network is turned off, as indicated by in the signal strength indicator area, and you cannot use SIM card services or features requiring cellular network coverage.When the wireless device is in the remote SIM mode, you can only use a compatible connected enhancement, such as a car kit, to make or receive calls. Your wireless device will not make any calls, except to the emergency numbers programmed into your device, while in this mode. To make calls from your device, you must first leave the remote SIM mode. If the device has been locked, enter the lock code to unlock it first.To leave the remote SIM mode, press the power key, and select Exit remote SIM mode.Connection manager Data connectionsPress , and select Tools > Connectivity > Conn. mgr. > Active data connections. In the active connections view, you can see the open data connections: data calls ( ), high-speed data calls ( ), packet data connections ( ), and wireless LAN connections ( ). Note: The actual time invoiced for calls by your service provider may vary, depending on network features, rounding off for billing, and so forth.To end a connection, select Options > Disconnect. To close all open connections, select Options > Disconnect all.P2954_en.book Page 77 Tuesday, July 3, 2007 2:51 PM

Connections78To view the details of a connection, select Options > Details. The details shown depend on the connection type.Wireless LANTo search for wireless LANs available within range, press , and select Tools > Connectivity > Conn. mgr. > Available WLAN networks.The available wireless LAN view shows a list of wireless LANs within range, their network mode (Infrastructure or Ad-hoc), and signal strength indicator. is shown for networks with encryption, and if your device has an active connection in the network.To view the details of a network, select Options > Details.To create an internet access point in a network, select Options > Define access point.USB Press , and select Tools > Connectivity > USB.To have the device ask the purpose of the USB cable connection each time the cable is connected, select Ask on connection > Yes.If Ask on connection is set to off or you want to change the mode during an active connection, select USB mode and from the following:Media player—to synchronize music with Windows Media Player. See ‘Music transfer with Windows Media Player’, p. 22.PC Suite—to use Nokia PC applications such as Nokia Nseries PC Suite, Nokia Lifeblog, and Nokia Software UpdaterData transfer— to transfer data between your device and a compatible PCImage print—to print images on a compatible printer. See ‘Image print’, p. 51.PC connectionsYou can use your device with a variety of compatible PC connectivity and data communications applications. With Nokia Nseries PC Suite you can, for example, transfer images between your device and a compatible PC.Always create the connection from the PC to synchronize with your device.P2954_en.book Page 78 Tuesday, July 3, 2007 2:51 PM

Connections81configure the internet access point. This step reduces the risk of an unwanted party joining the ad hoc network.Your device notifies you if another device attempts to connect to it and the home network. Do not accept connection requests from an unknown device.If you use wireless LAN in a network that does not have encryption, switch off sharing Nokia N81 files with other devices, or do not share any private media files. To change sharing settings, see ‘Home media settings’, p. 81.Home media settingsTo share media files with other compatible UPnP devices through wireless LAN, you must create and configure your wireless LAN home internet access point, then configure the Home netw. application. See ‘Wireless LAN’, p. 72 and the wireless LAN settings in ‘Access points’, p. 124.The options related to Home network in applications are not available before the Home network settings have been configured.When you access the home media application for the first time, the setup wizard opens, and helps you to define the home media settings for your device. To use the setup wizard later, in the home network main view, select Options > Run wizard, and follow the instructions on the display.To connect a compatible PC to the home network, on the PC, you must install the related software from the DVD-ROM supplied with your device.Configure settingsTo configure the home media application, select Tools > Connectivity > Home netw.> Settings and from the following: Home access point—Select Always ask if you want the device to ask for the home access point every time you connect to the home network, Create new to define a new access point that is used automatically when you use Home netw., or None. If your home network does not have wireless LAN security settings enabled, you get a security warning. You can continue, and switch the wireless LAN security on later; or cancel defining the access point, and first switch on the wireless LAN security. See Wireless LAN in ‘Access points’, p. 124.Device name— Enter a name for your device that is shown to the other compatible devices in the home network.Set sharing on and define contentSelect Tools > Connectivity > Home netw. > Share content.Content sharing—Allow or deny sharing media files with compatible devices. Do not set Content sharing on before you have configured all the other settings. If you set P2954_en.book Page 81 Tuesday, July 3, 2007 2:51 PM

Applications84ApplicationsClock Press , and select Applications > Clock. To view your active and inactive alarms, press . To set a new quick alarm, select Options > New quick alarm. When an alarm is active, is shown.Quick alarms are set for the next 24 hours and they cannot be repeated.To turn off the sounding alarm, select Stop. To stop the alarm for 5 minutes, select Snooze.If the alarm time is reached while the device is switched off, the device switches itself on and starts sounding the alarm tone. If you select Stop, the device asks whether you want to activate the device for calls. Select No to switch off the device or Yes to make and receive calls. Do not select Yes when wireless phone use may cause interference or danger.To cancel the next alarm, select Applications > Clock > Options > Remove alarm.To set a new alarm, select Applications > Clock , press , and select Options > Set alarm. Define the repetition, if needed.To change clock settings, select Applications > Clock > Options > Settings. Set time and date, define time and date formats, clock type, or the alarm tone. In Workdays select weekdays for repetition options.To allow the mobile phone network to update the time, date, and time zone information to your device (network service), select Applications > Clock > Options > Settings >Network operator time > Auto-update.World clockTo open the world clock view, select Clock, and press twice. To add cities to the list, select Options > Add city. You can add a maximum of 15 cities to the list.To open the world clock view, select Clock, and press twice. In the world clock view, you can view the time in different cities. To add cities to the list, select Options > Add city. You can add a maximum of 15 cities to the list.To set your current city, scroll to a city, and select Options > Set as current city. The city is displayed in the clock main view, and the time in your device is changed according to the city selected. Check that the time is correct and matches your time zone.P2954_en.book Page 84 Tuesday, July 3, 2007 2:51 PM

Applications85Calculator Press , and select Applications > Calculator. Note: This calculator has limited accuracy and is designed for simple calculations.Notes To write notes in .txt format, press , and select Applications > Notes.Application manager Press , and select Applications > App. mgr.. You can install two types of applications and software to your device:•J2METM applications based on JavaTM technology with the extension .jad or .jar ( ). •Other applications and software suitable for the Symbian operating system ( ). The installation files have the .sis extension. Only install software specifically designed for your Nokia N81. Software providers will often refer to the official model number of this product: the Nokia N81-1.Installation files may be transferred to your device from a compatible computer, downloaded during browsing, or sent to you in a multimedia message, as an e-mail attachment, or using Bluetooth connectivity. You can use Nokia Application Installer in Nokia Nseries PC Suite to install an application to your device.Install applications and software indicates a .sis application, a Java application, that the application is not fully installed, and that the application is installed in the memory card. Important: Only install and use applications and other software from trusted sources, such as applications that are Symbian Signed or have passed the Java VerifiedTM testing.Before installation, note the following:•To view the application type, version number, and the supplier or manufacturer of the application, select Options > View details.To display the security certificate details of the application, in Certificates, select View details. See ‘Certificate management’, p. 119.•If you install a file that contains an update or repair to an existing application, you can only restore the original application if you have the original installation file or a full back-up copy of the removed software package. To restore the original application, remove the application, and install the application again from the original installation file or the back-up copy.P2954_en.book Page 85 Tuesday, July 3, 2007 2:51 PM

Applications86•The .jar file is required for installing Java applications. If it is missing, the device may ask you to download it. If there is no access point defined for the application, you are asked to select one. When you are downloading the .jar file, you may need to enter a user name and password to access the server. You obtain these from the supplier or manufacturer of the application.1To locate an installation file, press , and select Tools > App. mgr.. Alternatively, search the device memory or the memory card in File mgr., or open a message in Messaging > Inbox that contains an installation file.2In App. mgr., select Options > Install. In other applications, scroll to the installation file, and press to start the installation.During installation, the device shows information about the progress of the installation. If you are installing an application without a digital signature or certification, the device displays a warning. Continue installation only if you are sure of the origin and contents of the application.To start an installed application, locate it in the menu, and press . If the application does not have a default folder defined, it is installed in the Applications folder.To see which software packages are installed or removed and when, select Options > View log. Important: Your device can only support one antivirus application. Having more than one application with antivirus functionality could affect performance and operation or cause the device to stop functioning.After you install applications to memory card, installation files (.sis) remain in the device memory. The files may use large amounts of memory and prevent you from storing other files. To maintain sufficient memory, use Nokia Nseries PC Suite to back up installation files to a compatible PC, then use the file manager to remove the installation files from the device memory. See ‘File manager’, p. 70. If the .sis file is a message attachment, delete the message from the Messaging inbox.Remove applications and softwareScroll to a software package, and select Options > Remove. Select Yes to confirm.If you remove software, you can only reinstall it if you have the original software package or a full backup of the removed software package. If you remove a software package, you may no longer be able to open documents created with that software.If another software package depends on the software package that you removed, the other software package may stop working. Refer to the documentation of the installed software package for details.P2954_en.book Page 86 Tuesday, July 3, 2007 2:51 PM

Applications87SettingsSelect Options > Settings and from the following:Software installation—Select whether Symbian software that has no verified digital signature can be installed.Online certificate check—Select to check the online certificates before installing an application.Default web address—Set the default address used when checking online certificates.Some Java applications may require a message to be sent or a network connection to a specific access point for downloading extra data or components. In the App. mgr. main view, scroll to an application, and select Options > Open to change settings related to that specific application.Calendar Press , and select Applications >Calendar. To add a new calendar entry, scroll to the desired date, select Options > New entry and the entry type.Press , and select Calendar. To add a new calendar entry, scroll to the desired date, select Options > New entry and one of the following:1Meeting—to remind you of an appointment that has a specific date and timeMemo—to write a general entry for a dayAnniversary—to remind you of birthdays or special dates (entries are repeated every year)To-do—to remind you of a task that needs doing by a specific date2Fill in the fields. To set an alarm, select Alarm > On, and enter the Alarm time and Alarm date.To add a description for an appointment, select Options > Add description.3To save the entry, select Done. Shortcut: In the day, week, or month calendar view, press any key ( — ). An appointment entry opens, and the characters you enter are added to Subject. In the to-do view, a to-do note entry opens.When the calendar alarms for a note, select Silence to turn off the calendar alarm tone. The reminder text stays on the screen. To end the calendar alarm, select Stop. To set the alarm to snooze, select Snooze.You can synchronize your calendar with a compatible PC using Nokia Nseries PC Suite. When creating a calendar entry, set the desired Synchronisation option.P2954_en.book Page 87 Tuesday, July 3, 2007 2:51 PM

Applications88Select Options to add new entries, change settings, go to a specific date, send a calendar note to a compatible device, delete entries, and mark tasks as completed.Calendar viewsSelect Options > Settings to change the starting day of the week or the view that is shown when you open the calendar.To go to a certain date, select Options > Go to date. To jump to today, press .To switch between the month view, week view, day view, and to-do view, press .To send a calendar note to a compatible device, select Options > Send.If the other device is not compatible with Coordinated Universal Time (UTC), the time information of received calendar entries may not be displayed correctly.To modify the calendar, select Options > Settings > Calendar alarm tone, Default view, Week starts on, and Week view title.Manage your calendar entriesTo delete more than one event at a time, go to the month view, and select Options > Delete entry > Before date or All entries.To mark a task as completed, scroll to it in the to-do view, and select Options > Mark as done.Recorder To record voice memos, press , and select Applications > Media > Recorder. To record a telephone conversation, open Recorder during a voice call. Both parties hear a tone every 5 seconds during recording.RealPlayer Press , and select Applications > Media > RealPlayer. With RealPlayer, you can stream media files over the air without saving them to the device first or play video clips saved in the device.RealPlayer supports files with extensions such as .3gp, .mp4, or .rm. However, RealPlayer does not necessarily support all file formats or all the variations of file formats.In the landscape view, use the media keys to control the player.P2954_en.book Page 88 Tuesday, July 3, 2007 2:51 PM

Applications89Play video clips1To play a saved media file, select Options > Open and from the following:Most recent clips—to play one of the last six files played in RealPlayer.Saved clip—to play a file saved in Gallery2Scroll to a file, and press to play the file.To adjust the volume, use the volume key.Stream content over the airMany service providers require you to use an internet access point (IAP) for your default access point. Other service providers allow you to use a WAP access point.In RealPlayer, you can only open an rtsp:// URL address. However, RealPlayer will play a .ram file if you open an http link to it in Browser.To stream content over the air, select a streaming link saved in Gallery, on a web page, or received in a text message or multimedia message.Before live content begins streaming, your device connects to the site and starts loading the content. Only the link to the content is saved in your device.RealPlayer settingsYou may receive RealPlayer settings in a special message from the service provider. See ‘Data and settings’, p. 37. For more information, contact your service provider.Select Options > Settings and from the following:Video—to adjust the contrast of the video or have RealPlayer automatically repeat video clips after they finish playing.Streaming—Contact your service provider for the correct settings.Adobe Flash Player To view, play, and interact with compatible flash files made for mobile devices, press , and select Applications > Media > Flash Player. Scroll to a flash file, and press .IM—instant messagingPress , and select Applications > Media > IM.Instant messaging (network service) allows you to converse with other people using instant messages and join discussion forums (IM groups) with specific topics. P2954_en.book Page 89 Tuesday, July 3, 2007 2:51 PM

Applications90Various service providers maintain IM servers that you can log in to after you register to an IM service. Service providers may differ in their support of features.Select Conversations to start or continue a conversation with an IM user; IM contacts to create, edit, or view the online status of your IM contacts; IM groups to start or continue a group conversation with multiple IM users; or Recorded chats to view a previous instant messaging session that you saved.Receive IM settingsYou must save the settings to access the service that you want to use. You may receive the settings in a special text message from the network operator or service provider that offers the IM service. See ‘Data and settings’, p. 37. You can also enter the settings manually. See ‘Chat server settings’, p. 92.Connect to an IM server1To connect to the IM server in use, open IM, and select Options > Log in. To change the IM server in use and save new IM servers, see ‘Chat server settings’, p. 92.2Enter your user ID and password, and press to log in. You obtain the user ID and password for the IM server from your service provider.3To log out, select Options > Log out.Modify your IM settingsSelect Options > Settings > IM settings and from the following:Use screen name (shown only if IM groups are supported by the server)—To enter a nickname, select Yes.Show my availability—To allow others to see if you are online, select To everyone.Allow messages from—To allow messages from all, select All.Allow invitations from—To allow invitations only from your IM contacts, select IM contacts only. IM invitations are sent by IM contacts who want you to join their groups.Msg. scrolling speed—Select the speed at which new messages are displayed.Sort IM contacts—Select how your IM contacts are sorted: Alphabetically or By online status.Availability reloading—To select how to update information about whether your IM contacts are online or offline, select Automatic or Manual.Offline contacts—Select whether IM contacts with an offline status are shown in the IM contacts list.P2954_en.book Page 90 Tuesday, July 3, 2007 2:51 PM

Applications91Own message colour—Select the color of the instant messages you send.Received msg colour—Select the color of the instant messages you receive.IM alert tone—Change the tone played when you receive a new instant message.Search for IM groups and usersTo search for groups, in the IM groups view, select Options > Search. You can search by Group name, Topic, and Members (user ID).To search for users, in the IM contacts view, select Options > New IM contact > Search from server. You can search by User's name, User ID, Phone number, and E-mail address.Join IM groupsThe IM groups view shows a list of the IM groups that you have saved or are currently joined to.To join a saved IM group, press .To join an IM group that is not on the list, but for which you know the group ID, select Options > Join new group.To leave the IM group, select Options > Leave IM group.ChatAfter you join an IM group, you can view the messages that are exchanged there, and send your own messages.To send a message, write the message in the message editor field, and press .To send a private message to a participant, select Options > Send private message.To reply to a private message sent to you, select the message and Options > Reply.To invite IM contacts who are online to join the IM group, select Options > Send invitation.To prevent receiving messages from certain participants, select Options > Blocking options.Record chatsTo record the messages that are exchanged during a conversation or while you are joined in a IM group, select Options > Record chat. To stop recording, select Options > Stop recording. To view the recorded chats, in the main view, select Recorded chats.View and start conversationsThe Conversations view shows a list of the individual conversation participants that you have an ongoing P2954_en.book Page 91 Tuesday, July 3, 2007 2:51 PM

Applications92conversation with. Ongoing conversations are automatically closed when you exit IM.To view a conversation, scroll to a participant, and press .To continue the conversation, write your message, and press .To return to the conversations list without closing the conversation, select Back. To close the conversation, select Options > End conversation.To start a new conversation, select Options > New conversation.To save a conversation participant to your IM contacts, select Options > Add to IM contacts.To send automatic replies to incoming messages, select Options > Set auto reply on. You can still receive messages.IM contactsIn the IM contacts view, you can retrieve chat contact lists from the server, or add a new chat contact to a contact list. When you log in to the server, the previously used chat contact list is retrieved from the server automatically.Chat server settingsSelect Options > Settings > Server settings. You may receive the settings in a special text message from the network operator or service provider that offers the chat service. You obtain the user ID and password from your service provider when you register to the service. If you do not know your user ID or password, contact your service provider.Servers—View a list of all defined IM servers.Default server—Change the IM server to which you want to connect.IM login type—To log in automatically when you start IM, select On app. start-up.To add a new server to your list of IM servers, select Servers > Options > New server. Enter the following settings:Server name—the name for the chat serverAccess point in use—the access point you want to use for the serverWeb address—the URL address of the IM serverUser ID—your user IDPassword—your login passwordP2954_en.book Page 92 Tuesday, July 3, 2007 2:51 PM

Applications93Nokia Lifeblog To start Nokia Lifeblog on your device, press , and select Applications > Media > Lifeblog > Options > Open.Lifeblog is a combination of software for mobile device and PC that keeps a multimedia diary of the items that you collect with your device. Lifeblog organizes your photos, videos, sounds, text messages, multimedia messages, and weblog posts into a chronology that you can browse, search, share, publish, and back up. Both Nokia Lifeblog PC and Nokia Lifeblog mobile let you send or blog your items for others to see.Lifeblog mobile automatically keeps track of your multimedia items. Use Lifeblog on your device to browse your items, send them to others, or publish them on the web. Connect your device to a compatible PC using a compatible USB data cable or Bluetooth connectivity to transfer and synchronize the items on the device with your compatible PC.Lifeblog PC provides easy browsing and searching of the items that you collected with your device. With one-button transfer using a USB data cable or Bluetooth connectivity, your favorite photos, videos, text, and multimedia messages are transferred back to your device.For safekeeping, you can back up your Nokia Lifeblog database using your hard disk, compatible CDs, compatible DVDs, compatible removable drive, or compatible network drive. Additionally, you can post items to your weblog (blog).For more information on weblog services and their compatibility with Nokia Lifeblog, visit www.nokia.com/lifeblog, or press F1 in the Lifeblog PC application to open Nokia Lifeblog Help.Installation on your PCYou must install Nokia Lifeblog PC (provided on the DVD-ROM) to a compatible PC before using it.Before you install Nokia Lifeblog on a compatible PC, you need the following:•1 GHz Intel Pentium or equivalent, 128 MB RAM•400 MB of available hard disk space (if Microsoft DirectX and Nokia Nseries PC Suite must be installed) •Graphics capability of 1024x768 and 24-bit color•32 MB graphics card•Microsoft Windows 2000 or Windows XPTo install Lifeblog on your PC:1Insert the DVD-ROM supplied with your device.2Install Nokia Nseries PC Suite (includes Nokia Connectivity Cable drivers for USB connection).3Install Lifeblog for PC. P2954_en.book Page 93 Tuesday, July 3, 2007 2:51 PM

Applications94If Microsoft DirectX 9.0 is not already installed on your PC, it is installed at the same time with Lifeblog for PC.Connect your device and PCTo connect your device and a compatible PC using a compatible USB data cable:1Ensure that you have installed Nokia Nseries PC Suite (available on the CD-ROM).2Connect the USB data cable to the device and the PC. The USB mode should be PC Suite. When you connect your device to the PC for the first time after you have installed Nokia Nseries PC Suite, the PC installs the specific driver for your device. This may take a while.3Start the Lifeblog PC application.To connect your device and a compatible PC using Bluetooth wireless technology:1Ensure that you have installed Nokia Nseries PC Suite on your PC.2Ensure that you have paired your device and the PC through Bluetooth wireless technology with Get Connected in Nokia Nseries PC Suite (available on the CD-ROM). For more information on Nokia Nseries PC Suite, see the guides available at the Nokia N81 product support pages at www.nokia.com/support or your local Nokia website. For more information on Bluetooth connectivity, see the user guide for your device.3Activate Bluetooth connectivity on your device and on your PC.Copy itemsTo copy new or edited items from your device to your PC, and copy the selected items from your PC to your device:1Connect your device to the PC.2Start the Lifeblog application on your PC.3In the Lifeblog PC application, select File > Copy from phone and to Phone.The new items from your device are copied to your PC. The items on the To phone view on your PC are copied to your device.Browse timeline and favoritesWhen you start Lifeblog on your device, the Timeline view opens and shows your multimedia items. To open your saved favorites, select Options > View favourites.When you start Lifeblog on your PC, you have several ways to move around in the Timeline and Favourites views. The fastest way is to move the slider handle forward or backward, fast or slow. Alternatively, click the time bar to P2954_en.book Page 94 Tuesday, July 3, 2007 2:51 PM

Applications95select a date, use the Go to date feature, or use the arrow keys.Post to the webTo share your best Lifeblog items, send them to your weblog on the internet for others to see.You must first create an account with a compatible weblog service, create one or more weblogs that you use as the destination of your posts, and add the weblog account to Lifeblog. The recommended weblog service for Nokia Lifeblog is TypePad from Six Apart, www.typepad.com.On your device, to add the weblog account in Lifeblog, select Options > Settings > Blog. On your PC, edit accounts in the Blog account manager window.To post items to the web from your device, do the following:1In Timeline or Favourites, select the items that you want to post to the web.2Select Options > Post to Web.3If you use the feature for the first time, Lifeblog retrieves a weblog list from the weblog server.4The weblog post dialog opens. Select the weblog you want to use from the Post to: list. If you have created new weblogs, to update the weblog list, select Options > Refresh blog list. 5Enter a title and a caption for the post. You can also write a longer story or description in the body text field.6When everything is ready, select Options > Send.To post items to the web from your PC, do the following:1In Timeline or Favourites, select the items (a maximum of 50) that you want to post to the web.2Select File > Post to the Web.... The Post to the Web window opens.3Enter a title and a caption for the post. You can also write a longer story or description in the body text field.4Select the weblog that you want to use from the Post to: list.5When everything is ready, click the Send button.Import items from other sourcesIn addition to the .jpeg images of your device, you can also import .jpeg images and .3gp and .mp4 video clips, .amr sound files, and .txt text files from other sources (such as a CD, DVD, or folders on your hard disk) into Lifeblog.To import items from a compatible PC to Lifeblog for PC, do the following:1In Timeline or Favourites, select File > Import from PC.... The Import window opens.P2954_en.book Page 95 Tuesday, July 3, 2007 2:51 PM

Applications962Browse the list to find the image or video file, or sound or text file from the list, or navigate to other folders to find the file that you want to import. Use the Look in list to browse other drives or appliances.3Select a folder, file, or several files. You can view their content in the Preview: pane.4Click Open to import the folder (including subfolders) or selected files.Digital rights management Content owners may use different types of digital rights management (DRM) technologies to protect their intellectual property, including copyrights. This device uses various types of DRM software to access DRM-protected content. With this device you can access content protected with WMDRM 10, OMA DRM 1.0, and OMA DRM 2.0. If certain DRM software fails to protect the content, content owners may ask that such DRM software's ability to access new DRM-protected content be revoked. Revocation may also prevent renewal of such DRM-protected content already in your device. Revocation of such DRM software does not affect the use of content protected with other types of DRM or the use of non-DRM-protected content.Digital rights management (DRM) protected content comes with an associated activation key that defines your rights to use the content.If your device has OMA DRM protected content, to back up both the activation keys and the content, use the backup feature of Nokia Nseries PC Suite. Other transfer methods may not transfer the activation keys which need to be restored with the content for you to be able to continue the use of OMA DRM protected content after the device memory is formatted. You may also need to restore the activation keys in case the files on your device get corrupted.If your device has WMDRM protected content, both the activation keys and the content will be lost if the device memory is formatted. You may also lose the activation keys and the content in case the files on your device get corrupted. Losing the activation keys or the content may limit your ability to use the same content on your device again. For more information, contact your service provider.Some activation keys may be connected to a specific SIM card, and the protected content can be accessed only if the SIM card is inserted in the device.To view the digital rights activation keys stored in your device, press , and select Applications > Media > Actv. keys and from the following:P2954_en.book Page 96 Tuesday, July 3, 2007 2:51 PM

Applications97Valid keys—View keys that are connected to one or more media files and keys whose validity period has not started yet.Invalid keys—View keys that are not valid; the time period for using the media file is exceeded or there is a protected media file in the device but no connected activation key.Not in use—View keys that have no media files connected to them in the device.To buy more usage time or extend the usage period for a media file, select Options > Get new key.To view detailed information, such as the validity status and ability to send the file, scroll to an activation key, and press .Adobe Reader With Adobe Reader, you can read .pdf documents on the display of your device.This application has been optimized for .pdf document content on handsets and other mobile devices, and provides only a limited set of features compared with PC versions.To open documents, press , and select Applications > Office> Adobe PDF. Your recent files are listed in the file view. To open a document, scroll to it, and press .Use File mgr. to browse and open documents stored in the device.More informationFor more information, visit www.adobe.com.To share questions, suggestions, and information about the application, visit the Adobe Reader for Symbian OS user forum at http://adobe.com/support/forums/main.html.Converter To convert measures from one unit to another, press , and select Applications > Office> Converter.Converter has limited accuracy, and rounding errors may occur.1In the Type field, select the measure you want to use.2In the first Unit field, select the unit from which you want to convert. In the next Unit field, select the unit to which you want to convert.3In the first Amount field, enter the value you want to convert. The other Amount field changes automatically to show the converted value.P2954_en.book Page 97 Tuesday, July 3, 2007 2:51 PM

Applications98Set base currency and exchange ratesSelect Type > Currency > Options > Currency rates. Before you can make currency conversions, you must select a base currency and add exchange rates. The rate of the base currency is always 1.Note: When you change base currency, you must enter new exchange rates because all previously set exchange rates are cleared.P2954_en.book Page 98 Tuesday, July 3, 2007 2:51 PM

Personalize your device101To change the 3–D effect that is applied to the ringing tone, select Sound trajectory and the desired effect. To modify the effect, select from the following settings:Trajectory speed—Scroll left or right to adjust the speed at which sound moves from one direction to another. This setting is not available for all ringing tones.Reverberation—Select the type of echo.Doppler effect—Select On to have the ringing tone sound higher when you are closer to your device, and lower when you are farther away. When you get closer to the device, the ringing tone seems to become higher, and lower when you move away from it. The Doppler effect is not available for all sound trajectories.To listen to the ringing tone with the 3–D effect, select Options > Play tone.If you enable the 3-D tones but do not select any 3-D effect, stereo widening is applied to the ringing tone.To adjust the ringing tone volume, select Tools > Profiles > Options > Personalise > Ringing volume.Change the look of your device To change the look of the display, such as the wallpaper and icons, press , and select Tools > Settings > General > Personalisation > Themes.To change the theme that is used for all the applications in your device, select Themes > General.To preview a theme before activating it, select Options > Preview. To activate the theme, select Options > Set. The active theme is indicated by .The themes on the memory card are indicated by .To change the layout of the main menu, select Themes > Menu view.To open a browser connection and download more themes, in General or Menu view, select Download themes (network service). Important: Use only services that you trust and that offer adequate security and protection against harmful software.To edit the wallpaper, select Themes > Wallpaper to change the background image on the display for the active standby mode.P2954_en.book Page 101 Tuesday, July 3, 2007 2:51 PM

Personalize your device102Active standbyThe active standby display shows status indicators, widgets, the now playing view, and search.To switch the active standby on or off, press , and select Tools > Settings > General > Personalisation > Standby mode > Active standby.Scroll to an application or event, and press .The standard scroll key shortcuts available in the standby mode cannot be used when active standby is on.To change the default applications’ shortcuts, press , and select Tools > Settings > General > Personalisation > Standby mode > Active standby apps..Some shortcuts may be fixed, and you cannot change them.P2954_en.book Page 102 Tuesday, July 3, 2007 2:51 PM

Make calls103Make callsVoice calls1In the standby mode, enter the phone number, including the area code. To remove a number, press . For international calls, press twice for the + character (replaces the international access code), and enter the country code, area code (omit the leading zero if necessary), and phone number.2Press the call key to call the number.3Press the end key to end the call (or to cancel the call attempt). Pressing the end key always ends a call, even if another application is active. Closing the slide does not end an active voice call.To adjust the volume during a call, use the volume key on the side of your device. You can also use the scroll key. If you have set the volume to Mute, select Unmute first.To make a call from Contacts, press , and select Contacts. Scroll to the desired name, or enter the first letters of the name to the search field. Matching contacts are listed. To call, press the call key.You must copy the contacts from your SIM card to Contacts before you can make a call from Contacts. See ‘Copy contacts’, p. 32.To call a recently dialed number in the standby mode, press the call key. Scroll to the number, and press the call key.To send an image or a video clip in a multimedia message to the other participant of the call, select Options > Send MMS (in UMTS networks only). You can edit the message and change the recipient before sending. Press the call key to send the file to a compatible device (network service).To send DTMF tone strings (for example, a password), select Options > Send DTMF. Enter the DTMF string or search for it in Contacts. To enter a wait character (w) or a pause character (p), press repeatedly. Select OK to send the tone. You can add DTMF tones to the Phone number or DTMF fields in a contact card.To put an active voice call on hold while answering another incoming call, select Options > Hold. To switch between the active and the held call, select Options > Swap. To connect the active and held calls and drop yourself from the line, select Options > Transfer. Tip! When you have only one active voice call, to put the call on hold, press the call key. To activate the call, press the call key again.P2954_en.book Page 103 Tuesday, July 3, 2007 2:51 PM

Make calls104During an active call, to route the sound from the handset to the loudspeaker, select Options > Activate loudspeaker. If you have attached a compatible headset with Bluetooth connectivity, to route the sound to the headset, select Options > Activate handsfree. To switch back to the handset, select Options > Activate handset. Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud. To end an active call and replace it by answering the waiting call, select Options > Replace.If you have several calls active, to end them all, select Options > End all calls.Many of the options that you can use during a voice call are network services.For information on conference calls and voice dialling, see the extended user guide at www.nokia.com/support or your local Nokia web site.Internet callsWith the internet call service (network service), you can make and receive calls over the internet.To make or receive an internet call, your device must be connected to an internet call service.Press , and select Tools > Connectivity > Internet tel..To connect to an internet call service, your device must be in the coverage of a connection network, such as a wireless LAN access point. Important: Always enable one of the available encryption methods to increase the security of your wireless LAN connection. Using encryption reduces the risk of unauthorized access to your data.Some places, like France, have restrictions on the use of wireless LAN. Check with your local authorities for more information.Available access points vary according to the service provider. To connect to the internet call service, select an available connection network from the list, and press . The saved networks, which are marked with , are shown first on the list. To stop making the connection, select Cancel.After you have successfully connected to a service, you can save the used wireless LAN network as a known access point.Select Options and from the following:Connect to service—to establish a connection to a service, when there is an internet call service and suitable connection network available.P2954_en.book Page 104 Tuesday, July 3, 2007 2:51 PM

Make calls105Disconnect from serv.—to end to the connection to the internet call service.Change service—to select the internet call service for outgoing calls, if the device is connected to more than one service. This option is shown only if there is more than one configured service available.Configure service—to configure new services. This option is shown only if there are services that have not been configured.Save network—to save the network you are currently connected to. The previously saved networks are marked with on the list of networks. This option is shown only if you are connected to an unsaved wireless LAN network.Use hidden network—to connect to an internet call service using a hidden wireless LAN network.Refresh—to manually refresh the list of connection networks. Use this option if your wireless LAN network is not shown on the list. The list is also refreshed automatically every 15 seconds.Settings—to change the settings.Exit—to close the application.The available options may vary.Your device can be connected only to one wireless LAN access point at a time. If you use two or more internet call services, which use the same access point, your device may be connected to multiple services at the same time. The service used for outgoing internet calls is shown where the connection networks are listed; to change it, select Change service.When you are connected to an internet call service, is shown in the standby mode.You may have a shortcut for Internet tel. in the active standby, or you can add it there. By using the shortcut, you can register manually, if an internet call service and access point are available. If you are already connected to an internet call service, the device asks if you want to disconnect from the service.To make an internet call in the standby mode, enter the phone number or internet address and press the call key. To switch between the number and letter mode, press and hold #. To end the call, press the end key.You can also make an internet call from Contacts and Log. To make a call from Contacts, press and select Contacts, scroll to the desired contact, and select Options > Internet call. To make a call from Log, press and select Tools > Log > Recent calls and Missed calls, Received calls or Dialled numbers, scroll to the desired contact and select Options > Internet call.P2954_en.book Page 105 Tuesday, July 3, 2007 2:51 PM

Make calls106If Internet call is set as the preferred call type, and your device is connected to an internet call service, calls are made as internet calls as default.Your device supports voice calls over the internet (net calls). Your device attempts emergency calls primarily over cellular networks. If an emergency call using cellular networks is not successful, your device attempts an emergency call through your internet call provider. Due to the established nature of cellular telephony, you should use cellular networks for emergency calls, if possible. If you have cellular network coverage available, make sure that your cellular phone is switched on and ready to make calls before you attempt an emergency call. The capability for an emergency call using internet telephony depends on the availability of a WLAN network and your internet call provider's implementation of emergency call capabilities. Contact your internet call provider to check the internet telephony emergency call capability.SettingsTo see the settings for the internet call services, press , and select Tools > Connectivity > Internet tel. > Settings.To view or choose the preferred call type for outgoing calls, select Options > Change > Default call type > Cellular or Internet call.To open the service settings view of the selected service, select Options > Open.The available options may vary.Service settingsPress and select Tools > Connectivity > Internet tel. > Options > Settings > Settings: .To see the settings of the service, select Login type and from the following:Automatic—To automatically log in to the internet call service. When a known network is found, the device connects to the internet call service automatically.Manual—To manually log in to the internet call service.If you use the automatic login type for wireless LAN networks, the device periodically scans for wireless LAN networks, which increases the demand on battery power and reduces the battery life.Select Saved conn. networks to see the connection networks that are recognized by the internet call service. These networks are used for automatic login and are marked with on the list of connection networks.Select Edit service settings to open service-specific settings. This option is only available if a service-specific software plug-in has been installed in the device.P2954_en.book Page 106 Tuesday, July 3, 2007 2:51 PM

Make calls107Saved connection networksTo view or remove the connection networks you have saved for an internet call service, press , and select Tools > Connectivity > Internet tel. > Settings > Settings: > Saved conn. networks. > Options > Open.Select Options > Remove to remove a connection network from the service.Voice and video mailboxesTo call your voice or video mailbox (network services, video mailbox available only in the UMTS network), press and hold in the standby mode, and select Voice mailbox or Video mailbox. See also ‘Call divert’, p. 122, and ‘Video calls’, p. 108.To change the phone number of your voice or video mailbox, press , and select Tools > Call mailbox, a mailbox, and Options > Change number. Enter the number (obtained from your network service provider), and select OK.Make a conference call1Make a call to the first participant.2To make a call to another participant, select Options > New call. The first call is automatically put on hold.3When the new call is answered, to join the first participant in the conference call, select Options > Conference.To add a new person to the call, repeat step 2, and select Options > Conference > Add to conference. Your device supports conference calls between a maximum of six participants, including yourself.To have a private conversation with one of the participants, select Options > Conference > Private. Select a participant and Private. The conference call is put on hold on your device. The other participants can still continue the conference call. After you finish the private conversation, select Options > Add to conference to return to the conference call.To drop a participant, select Options > Conference > Drop participant, scroll to the participant, and select Drop. 4To end the active conference call, press the end key.Speed dial a phone numberTo activate speed dialing, press , and select Tools > Settings > Phone > Call >Speed dialling > On.To assign a phone number to one of the speed dialing keys ( – ), press , and select Tools > Utilities > Speed dial. Scroll to the key to which you want to assign the phone number, and select Options > Assign. is reserved for the voice or video mailbox. P2954_en.book Page 107 Tuesday, July 3, 2007 2:51 PM

Make calls108To call in the standby mode, press the speed dial key and the send key.Voice dialingYour device supports enhanced voice commands. Enhanced voice commands are not dependent on the speaker’s voice, so the user does not record voice tags in advance. Instead, the device creates a voice tag for the entries in contacts, and compares the spoken voice tag to it. The voice recognition in the device adapts to the main user’s voice to recognize the voice commands better.The voice tag for a contact is the name or nickname that is saved on the contact card. To listen to the synthesized voice tag, open a contact card, and select Options > Play voice tag.Make a call with a voice tag Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialing in all circumstances.When you use voice dialing, the loudspeaker is in use. Hold the device at a short distance away when you say the voice tag.1To start voice dialing, in the standby mode, press and hold the right selection key. If a compatible headset with the headset key is attached, press and hold the headset key to start voice dialing.2A short tone is played, and Speak now is displayed. Say clearly the name or nickname that is saved on the contact card.3The device plays a synthesized voice tag for the recognized contact in the selected device language, and displays the name and number. After a timeout of 2.5 seconds, the device dials the number.If the recognized contact was not correct, select Next to view a list of other matches or Quit to cancel voice dialing.If several numbers are saved under the name, the device selects the default number if it has been set. Otherwise the device selects the first available number of the following: Mobile, Mobile (home), Mobile (business), Telephone, Tel. (home), and Tel. (business).Video callsWhen you make a video call (network service), you can see a real-time, two-way video between you and the recipient of the call. The live video image, or video image captured by the camera in your device is shown to the video call recipient. To be able to make a video call, you must have a USIM card and be in the coverage of a UMTS network. For availability P2954_en.book Page 108 Tuesday, July 3, 2007 2:51 PM

Make calls109of and subscription to video call services, contact your network service provider.A video call can only be made between two parties. The video call can be made to a compatible mobile device or an ISDN client. Video calls cannot be made while another voice, video, or data call is active.Icons: You are not receiving video (the recipient is not sending video or the network is not transmitting it). You have denied video sending from your device. Even if you denied video sending during a video call, the call is still charged as a video call. Check the pricing with your service provider.1To start a video call, enter the phone number in the standby mode, or select Contacts and a contact.2Select Options > Call > Video call.The secondary camera on the front is used by default for video calls. Starting a video call may take a while. Waiting for video image is shown. If the call is not successful (for example, video calls are not supported by the network, or the receiving device is not compatible), you are asked if you want to try a normal call or send a text or multimedia message instead.The video call is active when you see two video images, and hear the sound through the loudspeaker. The call recipient may deny video sending ( ), in which case you only hear the sound and may see a still image or a grey background graphic.To change between showing video or hearing only sound, select Options > Enable or Disable > Sending video, Sending audio, or Sending aud. & video.To zoom in or out your own image, press or .To switch the places of the sent video images on the display, select Options > Change image order.To route the audio to a compatible headset with Bluetooth connectivity attached to your device, select Options > Activate handsfree. To route the audio back to the loudspeaker of your device, select Options > Activate handset.To adjust the volume during a video call, use the volume key on the side of the device.To use the main camera for sending video, select Options > Use main camera. To switch back to the secondary camera, select Options > Use secondary camera.Select Options > Enable or Disable to enable or disable video or audio, Change image order to change the order of sent video images, Activate handsfree or Activate handset to activate handsfree with a compatible device P2954_en.book Page 109 Tuesday, July 3, 2007 2:51 PM

Make calls111Your service provider may send you the settings over the air or give you a list of the needed parameters.If you know a recipient’s SIP address, you can enter it on the person’s contact card. Press , select Contacts, and open the contact card (or start a new card for that person). Select Options > Add detail > SIP or Share view. Enter the SIP address in the format username@domainname (you can use an IP address instead of a domain name).If you do not know a SIP address for the contact, you can also use the phone number of the recipient including the country code, for example +358, to share video (if supported by the network service provider).UMTS connection settingsTo set up your UMTS connection, do the following:•Contact your service provider to establish an agreement for you to use the UMTS network.•Ensure that your UMTS access point connection settings are configured properly. For help, see ‘Connection’, p. 124.Share live video or video clip1When a voice call is active, select Options > Share video > Live video, and open the lens cover in the back.To share a video clip, select Options > Share video > Recorded clip. A list of video clips saved in the device opens. Select a clip you want to share. To preview the clip, select Options > Play.2If you share live video, your device sends the invitation to the SIP address you have added to the contact card of the recipient. If you share a video clip, select Options > Invite. You may need to convert the video clip into a suitable format to be able to share it. Clip must be converted for sharing. Continue? is displayed. Select OK.If the contact information of the recipient is saved in Contacts, and the contact has several SIP addresses or phone numbers including the country code, select the desired address or number. If the SIP address or phone number of the recipient is not available, enter the SIP address or the phone number of the recipient including the country code, and select OK to send the invitation.3Sharing begins automatically when the recipient accepts the invitation.4Select Pause to pause the sharing session. Select Continue to resume sharing. To fast forward or rewind the video clip, press or . To play the clip again, select Play.5To end the sharing session, select Stop. To end the voice call, press the end key. Video sharing also ends if the active voice call ends.P2954_en.book Page 111 Tuesday, July 3, 2007 2:51 PM

Make calls112To save the live video you shared, select Save to accept the Save shared video clip? query. The shared video is saved in the Images & videos folder in Gallery.If you access other applications while you are sharing a video clip, the sharing is paused. To return to the video sharing view and continue sharing, in the active standby mode, select Options > Continue. See ‘Active standby’, p. 102.Accept an invitationWhen someone sends you a share invitation, an invitation message is displayed showing the sender’s name or SIP address. If your device is not set to Silent, it rings when you receive an invitation.If someone sends you a share invitation and you are not within UMTS network coverage, you will not know that you received an invitation.When you receive an invitation, select from the following:Accept—to activate the sharing session.Reject—to decline the invitation. The sender receives a message that you rejected the invitation. You can also press the end key to decline the sharing session and disconnect the voice call.When you are receiving a video clip, to mute the sound of the clip, select Mute.To end video sharing, select Stop. Video sharing also ends if the active voice call ends.Answer or decline a callTo answer the call, press the call key, or open the slide.To mute the ringing tone when a call comes in, select Silence.If you do not want to answer a call, press the end key. If you have activated the Call divert > If busy function to divert calls, declining an incoming call also diverts the call. See ‘Call divert’, p. 122.When you select Reject to reject an incoming call, you can send a text message informing the caller that you cannot answer the call. Select Options > Send text message. To set up this option and write a standard text message, see ‘Call’, p. 121.Answer or reject a video callWhen a video call arrives, is displayed. Press the call key to answer the video call. Allow video image to be sent to caller? is displayed. To start sending a live video image, select Yes.P2954_en.book Page 112 Tuesday, July 3, 2007 2:51 PM

Make calls113If you do not activate the video call, video sending is not activated, and you only hear the sound of the caller. A grey screen replaces the video image. To replace the grey screen with a still image captured by the camera in your device, see ‘Call’, Image in video call, p. 121.To end the video call, press the end key.Call waitingYou can answer a call while you have another call in progress if you have activated Call waiting in Tools > Settings > Phone > Call > Call waiting (network service).To answer the waiting call, press the call key. The first call is put on hold.To switch between the two calls, select Swap. To connect an incoming call or a call on hold with an active call and to disconnect yourself from the calls, select Options > Transfer. To end the active call, press the end key. To end both calls, select Options > End all calls.Log To monitor the phone numbers of missed, received, and dialed voice calls, press , and select Tools > Log >Recent calls. The device registers missed and received calls only if the network supports these functions, the device is switched on, and within the network service area.To clear all recent call lists, select Options > Clear recent calls in the recent calls main view. To clear one of the call registers, open the register you want to erase, and select Options > Clear list. To clear an individual event, open a register, scroll to the event, and press .Call duration To monitor the approximate duration of your incoming and outgoing calls, press , and selectTools > Log >Call duration. Note: The actual time invoiced for calls by your service provider may vary, depending on network features, rounding off for billing, and so forth.To clear call duration timers, select Options > Clear timers. For this you need the lock code. See ‘Phone and SIM card’, p. 118.Packet dataTo check the amount of data sent and received during packet data connections, press , and select Tools > Log > Packet data. For example, you may be charged for P2954_en.book Page 113 Tuesday, July 3, 2007 2:51 PM

Make calls114your packet data connections by the amount of data sent and received.Monitor all communication eventsIcons in Log are as follows: Incoming Outgoing Missed communication eventsTo monitor all voice calls, text messages, or data and wireless LAN connections registered by the device, press , select Tools > Log, and press to open the general log.Subevents, such as a text message sent in more than one part and packet data connections, are logged as one communication event. Connections to your mailbox, multimedia messaging center, or web pages are shown as packet data connections.To add an unknown phone number from Log to your contacts, select Options > Save to Contacts.To filter the log, select Options > Filter and a filter.To erase the contents of the log, recent calls register, and messaging delivery reports permanently, select Options > Clear log. Select Yes to confirm. To remove a single event from the log, press .To set the log duration, select Options > Settings > Log duration.Select Options to save an unknown phone number to Contacts, filter the log, clear the log contents, or set log duration in Settings.If you select No log, all the log contents, recent calls register, and messaging delivery reports are permanently deleted. Tip! In the details view, you can copy a phone number to the clipboard, and paste it to a text message, for example. Select Options > Copy number.To view from the packet data counter how much data is transferred and how long a certain packet data connection lasts, scroll to an incoming or outgoing event indicated by Pack., and select Options > View details.P2954_en.book Page 114 Tuesday, July 3, 2007 2:51 PM

Settings118Phone and SIM cardPIN code request—When active, the code is requested each time the device is switched on. Deactivating the personal identification number (PIN) code request may not be allowed by some SIM cards.PIN code, PIN2 code, and Lock code—You can change the lock code, PIN code, and PIN2 code. These codes can only include the numbers from 0 to 9. If you forget any of these codes, contact your service provider. See ‘Glossary of PIN and lock codes’, p. 118.Avoid using access codes similar to the emergency numbers to prevent accidental dialing of the emergency number.Keypad autolock period—Select whether the keypad is locked when your device has been idle for a certain period of time. Tip! To lock or unlock the keypad manually, pull the lock switch.Phone autolock period—To avoid unauthorized use, you can set a time-out after which the device automatically locks. A locked device cannot be used until the correct lock code is entered. To turn off the autolock period, select None.See ‘Glossary of PIN and lock codes’, p. 118.When the device is locked, calls may be possible to the official emergency number programmed into your device. Tip! To lock the device manually, press . A list of commands opens. Select Lock phone.Lock if SIM card changed—You can set the device to ask for the lock code when an unknown SIM card is inserted into your device. The device maintains a list of SIM cards that are recognized as the owner’s cards.Closed user group—You can specify a group of people to whom you can call and who can call you (network service).When calls are limited to closed user groups, calls may be possible to the official emergency number programmed into your device.Confirm SIM services—You can set the device to display confirmation messages when you are using a SIM card service (network service).Glossary of PIN and lock codesIf you forget any of these codes, contact your service provider.Personal identification number (PIN) code—This code protects your SIM card against unauthorized use. The PIN code (4 to 8 digits) is usually supplied with the SIM card. After three consecutive incorrect PIN code entries, the code is blocked, and you need the PUK code to unblock it.P2954_en.book Page 118 Tuesday, July 3, 2007 2:51 PM

Settings119UPIN code—This code may be supplied with the USIM card. The USIM card is an enhanced version of the SIM card and is supported by UMTS mobile phones.PIN2 code—This code (4 to 8 digits) is supplied with some SIM cards, and is required to access some functions in your device.Lock code (also known as security code)—This code (5 digits) can be used to lock the device to avoid unauthorized use. The factory setting for the lock code is 12345. To avoid unauthorized use of your device, change the lock code. Keep the new code secret and in a safe place separate from your device. If you forget the code, contact your service provider.Personal unblocking key (PUK) code and PUK2 code—These codes (8 digits) are required to change a blocked PIN code or PIN2 code, respectively. If the codes are not supplied with the SIM card, contact the service provider whose SIM card is in your device.UPUK code—This code (8 digits) is required to change a blocked UPIN code. If the code is not supplied with the USIM card, contact the service provider whose USIM card is in your device.Certificate managementDigital certificates do not guarantee safety; they are used to verify the origin of software.In the certificate management main view, you can see a list of authority certificates that are stored in your device. Press to see a list of personal certificates, if available.Digital certificates should be used if you want to connect to an online bank or another site or remote server for actions that involve transferring confidential information. They should also be used if you want to reduce the risk of viruses or other malicious software and be sure of the authenticity of software when downloading and installing software. Important: Even if the use of certificates makes the risks involved in remote connections and software installation considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted certificates for increased security to be available. Certificates have a restricted lifetime. If “Expired certificate” or “Certificate not valid yet" is shown even if the certificate should be valid, check that the current date and time in your device are correct.Before changing any certificate settings, you must make sure that you really trust the owner of the certificate and that the certificate really belongs to the listed owner.View certificate details—check authenticityP2954_en.book Page 119 Tuesday, July 3, 2007 2:51 PM

Settings120You can only be sure of the correct identity of a server when the signature and the period of validity of a server certificate have been checked.You are notified if the identity of the server is not authentic or if you do not have the correct security certificate in your device.To check certificate details, scroll to a certificate, and select Options > Certificate details. When you open certificate details, the validity of the certificate is checked, and one of the following notes may be displayed:•Certificate not trusted—You have not set any application to use the certificate. See ‘Change the trust settings’, p. 120.•Expired certificate—The period of validity has ended for the selected certificate.•Certificate not valid yet—The period of validity has not yet begun for the selected certificate.•Certificate corrupted—The certificate cannot be used. Contact the certificate issuer.Change the trust settingsBefore changing any certificate settings, you must make sure that you really trust the owner of the certificate and that the certificate really belongs to the listed owner.Scroll to an authority certificate, and select Options > Trust settings. Depending on the certificate, a list of the applications that can use the selected certificate is shown. For example:•Symbian installation: Yes—The certificate is able to certify the origin of a new Symbian operating system application.•Internet: Yes—The certificate is able to certify servers.•App. installation: Yes—The certificate is able to certify the origin of a new Java application.Select Options > Edit trust setting to change the value.Security moduleTo view or edit a security module (if available) in Security module, scroll to it, and press the scroll key. To view detailed information about a security module, scroll to it, and select Options > Security details.Factory settings To reset some of the settings to their original values, select Factory settings. To do this, you need the lock code. See ‘Phone and SIM card’, p. 118. After resetting, the device may take a longer time to power on. Documents and files are unaffected.P2954_en.book Page 120 Tuesday, July 3, 2007 2:51 PM

Settings121Sensor settingsSelect On to perform certain actions (for example, browse through lists in some applications) by sliding your finger around the rim of the scroll key.Positioning Positioning methods—Select the positioning methods used to detect the location of your device: Bluetooth GPS to use a compatible external GPS receiver with Bluetooth connectivity, and Network based to use information from the cellular network (network service). The location information can be used by compatible applications in your device.Positioning server—Define an access point and a positioning server for secure positioning. The positioning server may be preset by your service provider, and you may not be able to edit the settings.Phone To edit the settings related to making and receiving calls, press , and select Tools > Settings > Phone > Call, Call divert, Call barring, or Network.Press , and select Tools > Settings > Phone > Call to show your phone number or internet id to the person to whom you are calling, notify you of a waiting call, sound alert for incoming internet calls, set default call type, reject calls with SMS and enter the text used in the reply, show image in video calls, redial automatically, show call duration and summary, activate speed dial and answering by pressing any key, and choosing the line when using two telephone lines.Call Send my caller ID—You can set your phone number to be displayed to (Yes) or hidden from (No) the person to whom you are calling, or the value may be set by your service provider when you make a subscription (Set by network) (network service).Send my internet call ID—You can set your internet call ID to be displayed to (Yes) or hidden from (No) the person to whom you are calling.Call waiting—If you have activated call waiting (network service), the network notifies you of a new incoming call while you have a call in progress. Set the function on (Activate) or off (Cancel), or check whether the function is activated (Check status).Internet call waiting—Select Activated to be notified of a new incoming internet call while you have a call in progress.P2954_en.book Page 121 Tuesday, July 3, 2007 2:51 PM

Settings122Internet call alert—Select On to be alerted for incoming internet calls. If you select Off, you are not alerted, but a notification about missed calls appears.Default call type—To set internet calls as default calls when starting the call with the call key, select Internet call. If internet telephone service is not available, a regular voice call is started instead.Reject call with SMS—Select Yes to send a text message to a caller informing why you could not answer the call. See ‘Answer or decline a call’, p. 112.Message text—Write a text to be sent in a text message when you reject a call.Image in video call—If video is not sent during a video call, you can select a still image to be displayed instead.Automatic redial—Select On, and your device makes a maximum of 10 attempts to connect the call after an unsuccessful call attempt. To stop automatic redialing, press the end key.Show call duration—Activate this setting if you want the length of a call to be displayed during the call.Summary after call—Activate this setting if you want the duration of the call briefly displayed after the call.Speed dialling—Select On, and the numbers assigned to the speed dialing keys ( - ) can be dialed by pressing and holding the key. See also ‘Speed dial a phone number’, p. 107.Anykey answer—Select On, and you can answer an incoming call by briefly pressing any keypad key, except the left selection key, right selection key, power key, and end key.Line in use—This setting (network service) is shown only if the SIM card supports two subscriber numbers, that is, two phone lines. Select which phone line you want to use for making calls and sending text messages. Calls on both lines can be answered irrespective of the selected line. If you select Line 2 and have not subscribed to this network service, you will not be able to make calls. When line 2 is selected, is shown in the standby mode. Tip! To switch between the phone lines, press and hold in the standby mode.Line change—To prevent line selection (network service), select Disable if supported by your SIM card. To change this setting, you need the PIN2 code.Call divert Call divert allows you to divert your incoming calls to your voice mailbox or another phone number. For details, contact your service provider.P2954_en.book Page 122 Tuesday, July 3, 2007 2:51 PM

Settings123Select which calls you want to divert and the desired diverting option. To divert voice calls when your number is busy or when you reject incoming calls, select If busy. Set the option on (Activate) or off (Cancel), or check whether the option is activated (Check status).Several diverting options can be active at the same time. When all calls are diverted, is shown in the standby mode.Call barring and call diverting cannot be active at the same time.Call barring Call barring (network service) allows you to restrict the calls that you make or receive with the device. To change the settings, you need the barring password from your service provider.Select the desired barring option, and set it on (Activate) or off (Cancel), or check whether the option is active (Check status). Call barring affects all calls, including data calls.Call barring and call diverting cannot be active at the same time.When calls are barred, calls may be possible to certain official emergency numbers.Network Your device can automatically switch between the GSM and UMTS networks. The GSM network is indicated with in the standby mode. The UMTS network is indicated with .Network mode (shown only if supported by the network service provider)—Select which network to use. If you select Dual mode, the device uses the GSM or UMTS network automatically, according to the network parameters and the roaming agreements between the network service providers. Contact your service provider for more details.Operator selection—Select Automatic to set the device to search for and select one of the available networks, or Manual to manually select the network from a list of networks. If the connection to the manually selected network is lost, the device sounds an error tone and asks you to reselect a network. The selected network must have a roaming agreement with your home cellular network. Glossary: A roaming agreement is an agreement between two or more network service providers to enable the users of one service provider to use the services of other service providers.Cell info display—SelectOn to set the device to indicate when it is used in a cellular network based on P2954_en.book Page 123 Tuesday, July 3, 2007 2:51 PM

Settings124microcellular network (MCN) technology and to activate cell info reception.Connection To edit access point and other connection settings, press , and select Tools > Settings > Connection > Bluetooth, USB, Access points, Packet data, Wireless LAN, Data call, SIP settings, Internet telephone settings, Configurations, or APN control.For USB settings, see ‘USB’, p. 78.For settings for Bluetooth connectivity, see ‘Bluetooth connectivity’, ‘Settings’, p. 75.Data connections and access pointsYour device supports packet data connections (network service), such as GPRS in the GSM network. When you use your device in GSM and UMTS networks, multiple data connections can be active at the same time, and access points can share a data connection. In the UMTS network, data connections remain active during voice calls.You can also use a wireless LAN data connection. See ‘Wireless LAN’, p. 72. Only one connection in one wireless LAN can be active at a time, but several applications can use the same internet access point.To establish a data connection, an access point is required. You can define different kinds of access points, such as:•MMS access point to send and receive multimedia messages•Internet access point (IAP) to send and receive e-mail and connect to the internetCheck the type of access point you need with your service provider for the service you want to access. For availability and subscription to packet data connection services, contact your service provider.Access points You may receive access point settings in a message from a service provider. See ‘Data and settings’, p. 37. Some or all access points may be preset for your device by your service provider, and you may not be able to change, create, edit, or remove them. indicates a protected access point. indicates a packet data access point, and a wireless LAN access point. Tip! You can create internet access points in a wireless LAN with the WLAN wizard. See ‘WLAN wizard’, p. 73.To create a new access point, select Options > New access point.P2954_en.book Page 124 Tuesday, July 3, 2007 2:51 PM

Settings125To edit the settings of an access point, select Options > Edit. Follow the instructions from your service provider.Connection name—Enter a descriptive name for the connection.Data bearer—Select the data connection type.Depending on the data connection you select, only certain setting fields are available. Fill in all fields marked with Must be defined or with a red asterisk. Other fields can be left empty, unless you have been instructed otherwise by your service provider.To be able to use a data connection, the network service provider must support this feature, and if necessary, activate it for your SIM card.Packet data access pointsFollow the instructions from your service provider.Access point name—You obtain the access point name from your service provider.User name—The user name may be needed to make a data connection, and is usually provided by the service provider.Prompt password—If you must enter the password every time you log in to a server, or if you do not want to save your password in the device, select Yes.Password—A password may be needed to make a data connection, and is usually provided by the service provider.Authentication—Select Normal or Secure.Homepage—Depending on the access point you are setting up, enter the web address or the address of the multimedia messaging center.Select Options > Advanced settings to change the following settings:Network type—Select the internet protocol type to use: IPv4 or IPv6. The other settings depend on the selected network type.Phone IP address (for IPv4 only)—Enter the IP address of your device. DNS address—In Primary DNS address, enter the IP address of the primary DNS server. In Secondary DNS address, enter the IP address of the secondary DNS server. Contact your internet service provider to obtain these addresses.Proxy server address—Define the address for the proxy server.Proxy port number—Enter the proxy port number.Wireless LAN access points Follow the instructions from the wireless LAN service provider.WLAN network name—Select Enter manually or Search for networks. If you select an existing network, WLAN P2954_en.book Page 125 Tuesday, July 3, 2007 2:51 PM

Settings126network mode and WLAN security mode are determined by the settings of its access point device.Network status—Defines whether the target network is hidden or not.WLAN network mode—Select Ad-hoc to create an ad hoc network and to allow devices to send and receive data directly; a wireless LAN access point device is not needed. In an ad-hoc network, all devices must use the same WLAN network name.WLAN security mode—Select the encryption used: WEP, 802.1x (not for ad hoc networks), or WPA/WPA2. If you select Open network, no encryption is used. The WEP, 802.1x, and WPA functions can be used only if the network supports them.WLAN security settings—Enter the settings for the selected security mode:Security settings for WEP:•Wep key in use—Select the WEP key number. You can create up to four WEP keys. The same settings must be entered on the wireless LAN access point device.•Authentication type—Select Open or Shared for the authentication type between your device and the wireless LAN access point device.•WEP key settings—Enter WEP encryption (length of the key), WEP key format (ASCII or Hexadecimal), and WEP key (the WEP key data in the selected format).Security settings for 802.1x and WPA/WPA2:•WPA/WPA2—Select the means of authentication: EAP to use an extensible authentication protocol (EAP) plug-in, or Pre-shared key to use a password. Complete the appropriate settings:•EAP plug-in settings (only for EAP)—Enter the settings as your service provider instructs.•Pre-shared key (only for Pre-shared key)—Enter a password. The same password must be entered on the wireless LAN access point device.•WPA2 only mode (only for WPA/WPA2)—Select whether Temporal Key Integrity Protocol (TKIP) is used.Homepage—Define a home page.Select Options > Advanced settings and from the following:IPv4 settings: Phone IP address (the IP address of your device), Subnet mask (the subnet IP address), Default gateway (the gateway), and DNS address. Enter the IP addresses of the primary and secondary DNS server. Contact your internet service provider for these addresses.IPv6 settings > DNS address—Select Automatic, Well-known, or User defined.P2954_en.book Page 126 Tuesday, July 3, 2007 2:51 PM

Troubleshooting: Q&A129Troubleshooting: Q&AAccess codesQ: What is my password for the lock, PIN, or PUK codes?A: The default lock code is 12345. If you forget or lose the lock code, contact your device dealer.If you forget or lose a PIN or PUK code, or if you have not received such a code, contact your network service provider.For information about passwords, contact your access point provider, for example, a commercial internet service provider (ISP) or network service provider.Application not respondingQ: How do I close an application that is not responding?A: Press and hold . Scroll to the application, and press to close the application.Bluetooth connectivityQ: Why can’t I find my friend’s device?A: Check that both devices are compatible, have activated Bluetooth connectivity, and are not in hidden mode. Check also that the distance between the two devices is not over 10 meters (33 feet) and that there are no walls or other obstructions between the devices.Q: Why can’t I end a Bluetooth connection?A: If another device is connected to your device, you can either end the connection using the other device or by deactivating Bluetooth connectivity. Select Tools > Bluetooth > Bluetooth > Off.DisplayQ: Why do missing, discolored, or bright dots appear on the screen every time I turn on my device?A: This is a characteristic of this type of display. Some displays may contain pixels or dots that remain on or off. This is normal, not a fault.Home network (UPnP)Q: Why can’t the other device see the files stored on my device?A: Make sure that you have configured the home network settings, Content sharing is turned on in your device, and the other device is UPnP compatible.Q: What can I do if my home network connection stops working?A: Switch off the wireless LAN connection from your compatible PC and your device, and switch it on again. If this does not help, restart your compatible PC and your device. If the connection still does not work, reconfigure the WLAN settings in both your compatible PC and device. See ‘Wireless LAN’, p. 72, and ‘Connection’, p. 124.P2954_en.book Page 129 Tuesday, July 3, 2007 2:51 PM

Troubleshooting: Q&A130Q: Why can't I see my compatible PC in my device in the home network?A: If you are using a firewall application in your compatible PC, check that it allows home media server to use the external connection (you can add Home media server to the firewall application’s exceptions list). Check from the firewall settings that the firewall application allows traffic to the following ports: 1900, 49152, 49153, and 49154. Some WLAN access point devices have a built-in firewall. In such cases, check that the firewall in the access point device does not block traffic to the following ports: 1900, 49152, 49153, and 49154.Check that the WLAN settings are the same in your device and compatible PC.Memory lowQ: What can I do if my device memory is low?A: You can delete unused items saved in your device regularly to avoid memory getting low. See ‘Memory low—free memory’, p. 70. To delete contact information, calendar notes, call timers, call cost timers, game scores, or any other data, go to the respective application to remove the data. If you are deleting multiple items and one of the following notes are shown: Not enough memory to perform operation. Delete some data first. or Memory low. Delete some data from phone memory., try deleting items one by one (starting from the smallest item).To view what kind of data you have and how much memory the different data groups consume, press , and select Tools > File manager > Options > Memory details.Q: How can I save my data before deleting it?A: Save your data using one of the following methods:•Use Nokia Nseries PC Suite to make a backup copy of all data to a compatible computer.•Send images to your e-mail address, then save the images to your computer.•Send data using Bluetooth connectivity to a compatible device.MessagingQ: Why can’t I select a contact?A: The contact card does not have a phone number or an e-mail address. Add the missing information to the contact card in Contacts.Multimedia messagingQ: The note Retrieving message is shown briefly. What is happening? A: The device is trying to retrieve a multimedia message from the multimedia messaging center.Check that the settings for multimedia messaging are defined correctly and that there are no mistakes in phone numbers or addresses. Press , and select Messaging > Options > Settings > Multimedia msg..Q: How can I end the data connection when the device starts a data connection again and again?P2954_en.book Page 130 Tuesday, July 3, 2007 2:51 PM

Troubleshooting: Q&A131A: To stop the device from making a data connection, press , and select Messaging > Options > Settings > Multimedia message > Multimedia retrieval and one of the following:Manual—to have the multimedia messaging center save messages to be retrieved later. You receive a notification when there is a new multimedia message that you can retrieve in the multimedia message center.Off—to ignore all incoming multimedia messages. After this change, the device does not make any network connections related to multimedia messaging. PC connectivityQ: Why do I have problems in connecting the device to my PC?A: Make sure that Nokia Nseries PC Suite is installed and running on your PC. See the user guide for Nokia Nseries PC Suite on the DVD-ROM. For further information on how to use Nokia Nseries PC Suite, see the help function on Nokia Nseries PC Suite or visit the support pages at www.nokia.com.Q: Can I use my device as a fax modem with a compatible PC?A: You cannot use your device as a fax modem. However, with call diverting (network service), you can divert incoming fax calls to another phone number.Wireless LANQ: Why can't I see a wireless LAN (WLAN) access point even though I know I'm within its range?A: The WLAN access point may use a hidden service set identifier (SSID). You can only access networks that use a hidden SSID if you know the correct SSID, and have created a WLAN internet access point for the network on your Nokia device.Q: How do I switch wireless LAN (WLAN) off on my Nokia device?A: The WLAN on your Nokia device will switch off when you are not trying to connect, or are not connected to another access point, or scanning for available networks. To further reduce battery consumption, you can specify that your Nokia device does not scan, or scans less often, for available networks in the background. WLAN will switch off in between background scans.To change the background scan settings:1Press , and select Tools > Settings > Connection > Wireless LAN.2Change the value of Show WLAN availability to Never to stop background scans, or increase the background scan time interval in Scan for networks.3To save your changes, select Back.When Scan for networks is set to Never, the WLAN availability icon will not be shown in the standby mode. However, you can still manually scan for available WLAN networks, and connect to WLAN networks as usual.P2954_en.book Page 131 Tuesday, July 3, 2007 2:51 PM

Battery information132Battery informationCharging and dischargingYour device is powered by a rechargeable battery. The battery can be charged and discharged hundreds of times, but it will eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery. Use only Nokia approved batteries, and recharge your battery only with Nokia approved chargers designated for this device.If a replacement battery is being used for the first time or if the battery has not been used for a prolonged period, it may be necessary to connect the charger, then disconnect and reconnect it to begin charging the battery.Unplug the charger from the electrical plug and the device when not in use. Do not leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or before any calls can be made.Use the battery only for its intended purpose. Never use any charger or battery that is damaged.Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the connecting object.Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or cold battery may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures well below freezing.Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose as household waste.Do not dismantle or shred cells or batteries. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. In the event of such a leak, flush your skin or eyes immediately with water, or seek medical help.Nokia battery authentication guidelinesAlways use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from P2954_en.book Page 132 Tuesday, July 3, 2007 2:51 PM

Care and maintenance134Care and maintenanceYour device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you protect your warranty coverage.•Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it.•Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.•Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.•Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.•Do not attempt to open the device other than as instructed in this guide.•Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.•Do not paint the device. Paint can clog the moving parts and prevent proper operation.•Use a soft, clean, dry cloth to clean any lenses, such as camera, proximity sensor, and light sensor lenses.•Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the device and may violate regulations governing radio devices.•Use chargers indoors.•Always create a backup of data you want to keep, such as contacts and calendar notes.•To reset the device from time to time for optimum performance, power off the device and remove the battery.These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service facility for service.DisposalThe crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste.Return the products to collection to prevent possible harm to the environment or human health from uncontrolled waste disposal and to promote the sustainable reuse of material resources. Collection information is available from the product retailer, local waste authorities, national producer responsibility organizations, or your local Nokia representative. For more information, see product Eco-Declaration or country-specific information at www.nokia.com.P2954_en.book Page 134 Tuesday, July 3, 2007 2:51 PM

Additional safety information135Additional safety informationSmall childrenYour device and its enhancements may contain small parts. Keep them out of the reach of small children.Operating environmentThis device meets RF exposure guidelines when used either in the normal use position against the ear or when positioned at least 2.2 centimeters (7/8 inches) away from the body. When a carry case, belt clip, or holder is used for body-worn operation, it should not contain metal and should position the device the above-stated distance from your body.To transmit data files or messages, this device requires a quality connection to the network. In some cases, transmission of data files or messages may be delayed until such a connection is available. Ensure the above separation distance instructions are followed until the transmission is completed.Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic storage media near the device, because information stored on them may be erased.Medical devicesOperation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately shielded from external RF energy or if you have any questions. Switch off your device in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.Implanted medical devices Manufacturers of medical devices recommend that a minimum separation of 15.3 centimeters (6 inches) should be maintained between a wireless device and an implanted medical device, such as a pacemaker or implanted cardioverter defibrillator, to avoid potential interference with the medical device. Persons who have such devices should:•Always keep the wireless device more than 15.3 centimeters (6 inches) from the medical device when the wireless device is turned on.•Not carry the wireless device in a breast pocket.•Hold the wireless device to the ear opposite the medical device to minimize the potential for interference.•Turn the wireless device off immediately if there is any reason to suspect that interference is taking place.Complete_Safety.fm Page 135 Friday, July 13, 2007 12:22 PM

Additional safety information136•Read and follow the directions from the manufacturer of their implanted medical device.If you have any questions about using your wireless device with an implanted medical device, consult your health care provider.Hearing aids Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.VehiclesRF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more information, check with the manufacturer, or its representative, of your vehicle or any equipment that has been added.Only qualified personnel should service the device or install the device in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty that may apply to the device. Check regularly that all wireless device equipment in your vehicle is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags inflate with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may be illegal.Potentially explosive environmentsSwitch off your device when in any area with a potentially explosive atmosphere, and obey all signs and instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include below deck on boats, chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust, or metal powders. You should check with the manufacturers of vehicles using liquefied petroleum gas (such as propane or butane) to determine if this device can be safely used in their vicinity.P2954_en.book Page 136 Tuesday, July 3, 2007 2:51 PM

Additional safety information138Your mobile device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA) and Industry Canada. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use at the ear is 0.93 W/kg and when properly worn on the body is 0.60 W/kg. Complete_Safety.fm Page 138 Friday, July 13, 2007 12:21 PM

Additional safety information139P2954_en.book Page 139 Tuesday, July 3, 2007 2:51 PM

140IndexAaccess point name control 134access points 130activation keysSee digital rights managementactive standby mode 109Adobe reader 104alarm clock 91application manager 92applicationsinstalling 92Java 92removing 93Bbacking up media files 54batteriesauthenticating 138charging 138intended for use 10prolonging life 17Bluetooth 81device address 83pairing 83security 82sending data 82switching off 82bookmarks 74Ccache, clearing 75calculator 92calendarcreating entries 94synchronizing Nokia PC Suite 95call logSee logcallsanswering 119barring 129declining 119diverting 129duration 120international 110making 110missed 120received 120settings 128sharing video 117transferring 120waiting 120cameraactive toolbar 62adjusting lighting and color 65editing videos 55flash 64image setup settings 65saving video clips 68scenes 65self-timer 66sequence mode 66shooting video 68still image camera settings 64taking pictures 61video recorder settings 69cell broadcast 50certificates 126chargers 10chatSee instant messagingclock 91codes 125computer connections 85conference call 114configurations 134

141connection settings 130contact cards 38inserting pictures 38sending 38contact information 11converter 105copying contacts between the SIM card and device memory 39copyright protectionSee digital rights management 103Ddata cable 85data calls 134data connectionsdetails 84ending 84establishing 130indicators 14network 9, 129settingsdate 91delivery reports 48device manager 85dictionary 42digital rights management 103Download! 18DRMSee digital rights management 103Eediting images 54e-mailautomatic retrieving 46deleting mailbox 48deleting messages 46opening 45remote mailbox 44retrieving from mailbox 45saving 50sending 42settings 48viewing attachments 45writing 42Ffactory settings 127file formats.jad 92.jar 92, 93.sis 92music player 19RealPlayer 96file manager 77fixed dialing 39FM radio 24Ggalleryactive toolbar 53backing up files 54editing images 54images and videos 52ordering files in albums 54, 59presentations 57print basket 53printing images 58slide show 57gameplay 30games 30GPRSSee data connectionsGPSmaps 17gpssettings 127Hhands-free operationSee loudspeakerheadset 16help application 11Iidle sceenSee standby modeimagesSee gallery

142indicators 14installing applications 92instant messagingblocking 99connecting to a server 97recording messages 99sending instant messages 98internetSee webinternet access points (IAP)See access pointsinternet calls 134JJava 92Kkeyguard 124keypad lock 124Llanguage settings 123LED 16lock code 125logduration 121erasing contents 121filtering 121loudspeaker 16Mmailbox 44maps 17memoryfreeing memory 77viewing memory consumption 77memory card tool 77menu, rearranging 106messagingcell broadcast 50e-mail 42inbox 43, 46mailbox 44multimedia messages 42settings 47text messages 42missed calls 120MMSSee multimedia messagesmultimedia menu 15multimedia messagescreating 42receiving 43retrieving 44saving 50sending 42settings 47musicSee music playermusic playerdownloading music 23file formats 19music shop 23playing songs 19playlists 20transferring music 21NNavi scroll key 15, 127N-Gage 30Nokia wireless keyboard 89notes 92Ooriginal settings 127Ppacket data settings 133PC connections 85pdf files 104personalization 108phone language 123phonebookSee contact cardsPIN codes 125positioning 127power saver 122power saver LED 16, 124

143printingcontact cards 38images 58profiles 106PUK codes 125Rradio 24RealPlayer 96recent calls 120recorder 95remote mailbox 44, 45remote SIM mode 84resolutionvideo quality settings 69ringing tones3-D 107personal ringing tone 40See also profilesSsafetyadditional information 143emergency calls 145guidelines 8scenesimage scenes 65video scenes 65scroll key 15, 127security codeSee lock codesendingcontact cards, business cards 38messages 42video clips 56service commands 41settingsaccess points 131application 122applications 134Bluetooth connectivity 82call barring 129call diverting 129certificates 126configurations 134data calls 134data connections 130defining 12display 122e-mail 44, 48IM 97, 99internet calls 134keypad lock 124language 123lock code 125messaging 47multimedia messages 47original settings 127personalizing the phone 106PIN code 125positioning 127power saver 122sensor 127SIP 134slide handling 123text messages 47UPIN code 125UPUK code 126SIM cardcopying names and numbers to your device 39messages 46names and numbers 39using device without a SIM card 107sis file 92sleep mode 16, 124slide 123SMSSee text messagessnooze 91softwareinstalling applications 92removing applications 93transferring a file to your device 92

144software update 18, 85songsfile formats 19transferring 21sound clips 52soundsadjusting volume 16muting a ringing tone 119recording sounds 95speaker phoneSee loudspeakerspeed dialing 114standby mode 106, 123support information 11svg files 57switch 12synchronization 89Ttext messagesinbox 41receiving 43saving 50sending 42, 43settings 47writing 43themes 108time 91tonesSee ringing tonestransfer conflicts 14transferring content from another device 12transferring music 21troubleshooting 135UUMTSSee data connectionsUniversal Plug and Play 87unsupported file format 57updating software 85UPIN code 125UPUK code 126USB data cable 85USSD commands 41Vvideo callanswering 119making 115rejecting 119video clips 52video playerSee RealPlayervideosSee galleryVisual Radio 24voice commands 78voice dialing 114voice mailbox 114changing the phone number 114diverting calls to voice mailbox 129voice messages 114voice tags 78making calls 115volume controladjusting volume 16during a call 110loudspeaker 16Wwallpaperschanging 108using pictures 53, 63webaccess points, See access pointsblogs 73browser 71feeds 73service messages 44welcome application 12wireless LAN 79access point settings 132creating IAP 80, 85scanning 133security 87See also Universal Plug and Playsettings 133wizard 80writing language 123P2954_enIX.fm Page 144 Friday, July 13, 2007 12:31 PM

Navigation menu