Microwave Radio Communications STATXU044T1AK STRATA Microwave Transmitter User Manual Professional Report

Microwave Radio Communications LLC STRATA Microwave Transmitter Professional Report

Manual

STRATA TX SystemManual Part No. 400504-1Rev. A March 2005Operator’s GuideAnalog + Digital Portable 3.4 to 13.25 GHz Microwave Transmitter
Notices iSTRATA TX Operator’s GuideNoticesAbout This ManualPart number 400504-1Revision A - March 2005The information in the manual applies to the Microwave Radio Communications (MRC) STRATA TX System. CopyrightThe information in this book may be reproduced by the purchaser to the extent needed for their organization. No part of this material may be modified in any way or published for resale without the express written authorization of Microwave Radio Communications. © 2005 Microwave Radio Communications Microwave Radio Communications101 Billerica Avenue - Bldg. 6North Billerica, MA 01862-1256USATEL: 978.671.5700FAX: 978.671.5800Printed in U.S.A.Proprietary MaterialThe information and design contained within this manual was originated by and is the property of Microwave Radio Communications. Microwave Radio Communications reserves all patent proprietary design, manufacturing, reproduction use, and sales rights thereto, and to any articles disclosed therein, except to the extent rights are expressly granted to others. The foregoing does not apply to vendor proprietary parts.To allow for the introduction of design improvements, specifications are subject to change without notice.Quality CertificationMicrowave Radio Communications is certified to ISO 9001:2000.Regulatory StatusThis product is certified to conform to CENELEC standards EN 55020, EN 55013, EN 50082-1, and EN 60950 and carries the CE mark.Authorized EU representative: Vislink PLC.
Notices iiSTRATA TX Operator’s GuideConventions Pay special attention to information marked in one of the following ways:WARNING Follow WARNINGS closely to prevent personal injury or death.CAUTION Follow CAUTIONS to prevent damage to the equipment.Note Notes provide additional information to assist you in using and maintaining the equipment.On-Line ViewingText displayed as blue contains a hypertext link. Click on the hypertext to jump to that destination. Click on the blue destination to return. Viewing this manual on-line requires Adobe Acrobat, version 4.0 or above. Click on this icon to download your FREE copy of Adobe Acrobat Reader.Symbols UsedThe following symbols are used on the equipment: Symbol MeaningWARNING: General Warning. Risk of DangerWARNING: Risk of Electric ShockWARNING: Electrostatic Discharge. Possible Damage to EquipmentFuse - Identifies fuses or their location.Frame or Chassis Ground - Identifies the frame or chassis terminal.Earth Ground - Identifies the earth Ground TerminalProtective Earth Ground - Identifies any terminal which is intended for connection to an external conductor for protection against electric shock in case of a fault, or the terminal on a protective earth electrode.
Notices iiiSTRATA TX Operator’s GuideWarranty InformationProduct Manufactured by MRC:a. Products manufactured by MRC are warranted against defects in material and workmanship for a period of two (2) years from date of delivery as evidenced by MRC's packing slip or other transportation receipt (unless otherwise noted). b. MRC's sole responsibility under this warranty will be to either repair or replace, at its option, any component which fails during the applicable warranty period because of a defect in material or workmanship, provided Buyer has promptly reported same to MRC in writing. All replaced products and parts will become MRC's property.c. MRC will honor the warranty at the repair facility designated by MRC. It is Buyer's responsibility to return, at its expense, the allegedly defective product to MRC. Buyer must obtain a Return Material Authorization (RMA) number and shipping instructions from MRC prior to returning any product under warranty. Transportation charges for the return of the product to Buyer will be paid by MRC within the United States. For all other locations, the warranty excludes all costs of shipping, customs clearance and other related charges. If MRC determines that the product is not defective within the terms of this warranty, Buyer will pay MRC all costs of handling, transportation and repairs at the then prevailing repair rates.d. All the above warranties are contingent upon proper use of the product. These warranties will not apply (1) if adjustment, repair, or product or parts replacement is required because of accident, unusual physical, electrical or electromagnetic stress, neglect, misuse, failure of electric power, environmental controls, transportation, failure to maintained properly or otherwise in accordance with MRC specifications, or abuses other than ordinary use; (2) if the product has been modified by Buyer or has been repaired or altered outside MRC's repair facility, unless MRC specifically authorizes such repairs or alterations in each instance; or (3) where MRC serial numbers, warranty data or quality assurance decals have been removed or altered.e. No person, including any dealer, agent or representative of MRC is authorized to assume for MRC any other liability on its behalf except as set forth herein. If any payment is due MRC for services performed hereunder, it will be subject to the same payment terms as the original purchase.Products Manufactured By Others:For products not manufactured by MRC, the original manufacturer's or licensor's warranty will be assigned to Buyer to the extent permitted by the manufacturer or licensor and is in lieu of any other warranty, expressed or implied. For warranty information on a specific product, a written request should be made to MRC.All Products:THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES, OBLIGATIONS, AND LIABILITIES ON THE PART OF MRC. EXCEPT FOR THE EXPRESS WARRANTIES STATED HEREIN, MRC DISCLAIMS ALL WARRANTIES ON PRODUCTS FURNISHED HEREUNDER, INCLUDING, WITHOUT LIMITATION, ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MRC WILL HAVE NO RESPONSIBILITY FOR ANY PARTICULAR APPLICATION MADE OF ANY EQUIPMENT. Any description of equipment, whether in writing or made orally by MRC or its agents, specification sheets, models, bulletins,
Notices ivSTRATA TX Operator’s Guidedrawings, or similar materials used in connection with Buyer's order are for the sole purpose of identifying the equipment and will not be construed as an express warranty. Any suggestions by MRC or its agents regarding use, application or suitability of the equipment will not be construed as an express warranty. No warranties may be implied from any course of dealing or usage of trade. Buyer agrees that the exclusion of all warranties, other than those expressly provided herein, is reasonable.
Contents Contents-1STRATA TX Operator’s GuideAbout This Manual - - - - - - - - - - - - - - - - - - - - - - - - iCopyright- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - iProprietary Material - - - - - - - - - - - - - - - - - - - - - - - iQuality Certification - - - - - - - - - - - - - - - - - - - - - - - iRegulatory Status- - - - - - - - - - - - - - - - - - - - - - - - - iConventions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - iiOn-Line Viewing- - - - - - - - - - - - - - - - - - - - - - - - - - iiSymbols Used- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - iiWarranty Information - - - - - - - - - - - - - - - - - - - - - - - - - iiiProduct Manufactured by MRC: - - - - - - - - - - - - - - - iiiProducts Manufactured By Others:- - - - - - - - - - - - - iiiAll Products: - - - - - - - - - - - - - - - - - - - - - - - - - - - - iiiIntroduction - - - - - - - - - - - - - - - - - - - - - - - - - 1-1Chapter Overview - - - - - - - - - - - - - - - - - - - - - - - - - 1-1What This Manual Covers - - - - - - - - - - - - - - - - - - - 1-1How It’s Organized - - - - - - - - - - - - - - - - - - - - - - - - 1-1For Whom It’s Written - - - - - - - - - - - - - - - - - - - - - - 1-2Related Documents - - - - - - - - - - - - - - - - - - - - - - - - 1-2Ordering Documentation - - - - - - - - - - - - - - - - - - - - 1-2Calling for Service - - - - - - - - - - - - - - - - - - - - - - - - - 1-2Supported Repairs - - - - - - - - - - - - - - - - - - - - - - - - 1-3Tell Us What You Think! - - - - - - - - - - - - - - - - - - - - 1-3Product Description- - - - - - - - - - - - - - - - - - - 2-1Chapter Overview - - - - - - - - - - - - - - - - - - - - - - - - - 2-1System Description - - - - - - - - - - - - - - - - - - - - - - - - 2-1System Options - - - - - - - - - - - - - - - - - - - - - - - - 2-2Single Unit Systems - - - - - - - - - - - - - - - - - - - - - 2-3Multi-Unit Systems - - - - - - - - - - - - - - - - - - - - - - 2-3Remote Control Options - - - - - - - - - - - - - - - - - - 2-3Antenna and Power Options - - - - - - - - - - - - - - - 2-3Mounting and Deployment Options - - - - - - - - - - - 2-5System Integration - - - - - - - - - - - - - - - - - - - - - - 2-5System Components - - - - - - - - - - - - - - - - - - - - - - - 2-7STRATA TXU - - - - - - - - - - - - - - - - - - - - - - - - - - 2-7STRATA TCU - - - - - - - - - - - - - - - - - - - - - - - - - - 2-7STRATA ACU - - - - - - - - - - - - - - - - - - - - - - - - - - 2-8STRATA Remote Control Panels - - - - - - - - - - - - 2-8 TXU and TCU Configurations - - - - - - - - - - - - - - - - - 2-9Typical System Configurations - - - - - - - - - - - - - - - 2-12For More Information - - - - - - - - - - - - - - - - - - - - - - 2-12Routine Operation - - - - - - - - - - - - - - - - - - - - 3-1Chapter Overview - - - - - - - - - - - - - - - - - - - - - - - - - 3-1Overview of Controls, Indicators, and Connectors - - - 3-2TXU Controls, Indicators, and Connectors - - - - - - 3-2TCU Controls, Indicators, and Connectors - - - - - - 3-5ACU Controls, Indicators, and Connectors- - - - - - 3-8STRATA Standard Remote Control Panel Controls, Indi-cators, and Connectors - - - - - - - - - - - - - - - - - - - - - - - - 3-9STRATA Aircraft Remote Control Panel Controls, Indica-tors, and Connectors - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9Preparing for Operation - - - - - - - - - - - - - - - - - - - - 3-10Mobile Installation - - - - - - - - - - - - - - - - - - - - - - 3-10Portable Deployment - - - - - - - - - - - - - - - - - - - - 3-10Powering the STRATA TX System - - - - - - - - - - 3-12Single TCU Power Up and Power Down - - - - - - 3-13Single TXU Power up and Power Down- - - - - - - 3-14TXU and TCU Power Up and Power Down - Co-Located 3-15TXU and TCU Power Up and Power Down - Separate Lo-cations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-17Using the STRATA TX Screens - - - - - - - - - - - - - - - 3-19TXU and/or TCU Monitoring Operations - - - - - - - - - 3-20Here are the tasks described:
Contents-2STRATA TX Operator’s Guide- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-20Using the Monitor Screens in MPEG Output Mode 3-20Using the Monitor Screens in Ext IF Input Mode 3-22Using the Monitor Screens in COFDM - IF Mode 3-23Using the Monitor Screens in COFDM ASI In Mode 3-24Using the Monitor Screens in Analog - IF Mode- 3-25Using the Monitor Screens in DVB-S Mode - - - - 3-26TXU and/or TCU Control Operations - - - - - - - - - - - 3-27Changing a Preset - - - - - - - - - - - - - - - - - - - - - 3-29Setting a Channel- - - - - - - - - - - - - - - - - - - - - - 3-30Setting Power Output - - - - - - - - - - - - - - - - - - - 3-31Controlling TCU to TXU DC Power on Coax - - - 3-32Front Panel vs. STRATA TX Configurator Settings - 3-34Troubleshooting - - - - - - - - - - - - - - - - - - - - - 4-1Chapter Overview - - - - - - - - - - - - - - - - - - - - - - - - - 4-1Status LED - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1Messages on Display- - - - - - - - - - - - - - - - - - - - - - - 4-1Error Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3Primary Error Code- - - - - - - - - - - - - - - - - - - - - - 4-3Error Status - - - - - - - - - - - - - - - - - - - - - - - - - - 4-8Unit ID - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-8Operational Problems - - - - - - - - - - - - - - - - - - - - - - 4-8Channels & Frequencies - - - - - - - - - - - - - - - A-1Appendix Overview - - - - - - - - - - - - - - - - - - - - - - - - A-1Initial Factory Presets - - - - - - - - - - - - - - - - - - - - - - A-13.4 to 3.8 GHz Channel Plan - - - - - - - - - - - - - - - A-14.4 to 5.0 GHz Channel Plan - - - - - - - - - - - - - - - A-26.4 to 7.1 GHz Channel Plan - - - - - - - - - - - - - - - A-26.9 to 7.5 GHz Channel Plan - - - - - - - - - - - - - - - A-37.4 to 8.0 GHz Channel Plan - - - - - - - - - - - - - - - A-37.8 to 8.5 GHz Channel Plan - - - - - - - - - - - - - - - A-48.2 to 8.9 GHz Channel Plan - - - - - - - - - - - - - - - A-410.0 to 10.7 GHz Channel Plan - - - - - - - - - - - - - A-510.5 to 11.2 GHz Channel Plan - - - - - - - - - - - - - A-510.8 to 11.5 GHz Channel Plan - - - - - - - - - - - - - A-612.7 to 13.25 GHz Channel Plan- - - - - - - - - - - - - A-6Glossary - - - - - - - - - - - - - - - - - - - - - - - - - - - B-1
1 Introduction 1-1STRATA TX Operator’s GuideIntroduction1.1 Chapter OverviewThis chapter will introduce you to the Operator’s Guide: what it covers, how it’s organized, and for whom it’s written.1.2 What This Manual CoversThis manual describes how to operate the STRATA TX Transmitter System.For information on Installation, Repair, Replacement Parts, and Theory of Operation, refer to the STRATA TX Technical Reference Manual. This manual also covers various configurations of the STRATA TX System. Your STRATA TX System will consist of one of the following configurations:• A Standalone Transmitter Control Unit (TCU)• A Standalone Transmitter Unit (TXU)• A TCU and TXU.Your TX System may be mounted on a tripod or may be mounted in a vehicle or in an aircraft. Your TX System may also include an optional MRC AC to DC Converter Unit (ACU). If your system is mounted in a vehicle or in an aircraft, it may include an optional MRC Remote Control Panel or Aircraft Remote Control Panel. This manual provides coverage for all of these various configurations.1.3 How It’s OrganizedThe manuals for the STRATA TX System are organized as follows:Chapter Operator’s GuideTechnical Reference ManualIntroductionProduct DescriptionRoutine OperationAdvanced OperationInstallationTroubleshootingRepairReplacement PartsTheory of OperationAppendix A - Channels & FrequenciesAppendix B - GlossaryAppendix C -Configurator Reference
Introduction 1-2STRATA TX Operator’s GuideNote The Technical Reference Manual contains everything in the Operator’s Guide, plus additional technical content. 1.4 For Whom It’s WrittenThis manual is intended for use by personnel assigned to operate the STRATA TX System. Users of this manual should already be familiar with basic concepts of radio, video, and audio.1.5 Related Documents• STRATA TX System Technical Reference Manual (part no. 400505-1)• STRATA TX System Quick Reference Card (part no. 400506-1)• STRATA Aircraft Remote Control Panel Operator’s Guide (part no. 400490)• STRATA Remote Control Panel Operator’s Guide (part no. 400489) 1.6 Ordering DocumentationAny of the above manuals may be ordered by contacting MRC Customer Service:Business Hours: Monday8:00 AM - 5:00 PM Eastern Time (US)(0800 - 1700 hrs US ET)Tuesday - Friday8:00 AM - 7:00 PM Eastern Time (US)(0800 - 1900 hrs US ET)Telephone: 800-490-5700978-671-5700Fax: 978-671-5800When contacting Customer Service, please have the following information available:• Model number and serial number of the unit. This is located on a label on the bottom of each unit.• Approximate purchase date.• Firmware revision, which appears on the TXU or TCU alphanumeric display at startup. or• Firmware revision(s) displayed on the Main page of the STRATA TX Configurator, when the STRATA TX Configurator is connected to the TXU or TCU.1.7 Calling for ServiceMRC Technical Support is available 24 hours a day, 7 days a week. During regular business hours you can reach our expert staff directly. After hours, your call will be forwarded to the on-call Technical Support specialist.Business Hours: Monday8:00 AM - 5:00PM Eastern Time (US)(0800 - 1700 hrs US ET)
Introduction 1-3STRATA TX Operator’s GuideTuesday - Friday8:00 AM - 7:00PM Eastern Time (US)(0800 - 1900 hrs US ET)Telephone: 800-490-5700978-671-5700Fax: 978-671-5800E-mail: support@mrcbroadcast.comWhen contacting Technical Support, please have the following information available:• Model number and serial number of the unit. This is located on a label on the bottom of each unit.• Approximate purchase date.• Firmware revision, which appears on the TXU or TCU alphanumeric display at startup.1.8 Supported Repairs The STRATA TX System, including the TXU, TCU, and optional ACU, is designed to be compact, rugged and reliable. The TXU and TCU require specialized test equipment to calibrate amplitude and frequency characteristics after repair. In addition, sealing the TXU, TCU, or optional ACU enclosures after repair requires exacting techniques and special fixtures to ensure weather resistance of the units. Therefore, there are NO supported field repairs to either the TXU, TCU, or ACU. Return the entire unit for factory repair. If you attempt field repair, you risk damaging your equipment. If your equipment is under warranty, you may also affect your warranty coverage. 1.9 Tell Us What You Think!We’d appreciate any comments or suggestions you have about this manual. The more feedback we get, the better the manuals get!If you’re viewing this manual electronically, it’s easy - just click on the link below send us an E-mail. Or, you can E-mail our Technical Support team at:support@mrcbroadcast.com. Be sure to tell us what product you’re writing about, and which manual - the Operator’s Guide, the Quick Reference Card, or the Technical Reference Manual.Feedback
Introduction 1-4STRATA TX Operator’s GuideThis page intentionally left blank.
2 Product Description 2-1STRATA TX Operator’s Guide/Tech Ref ManualProduct Description2.1 Chapter OverviewThis chapter provides an overall description of the STRATA TX System, its components, and its capabilities. Here are the topics covered:Topic PageSystem Description 2-1 System Options 2-2 Single Unit Systems 2-3 Multi-Unit Systems 2-3 Remote Control Options 2-3 Antenna and Power Options 2-3 Mounting and Deployment Options 2-5 System Integration 2-5System Components 2-7 STRATA TXU 2-7 STRATA TCU 2-7 STRATA ACU 2-8 STRATA Remote Control Panels 2-8TXU and TCU Configurations 2-9Typical System Configurations 2-12For More Information 2-122.2 System Description The STRATA TX System is a highly reliable, flexible, and compact portable microwave transmitter system ideal for tripod, airborne, or mobile installations. A typical STRATA TX System is composed of the Transmitter Unit (TXU) and the Transmitter Control Unit (TCU), as shown in Figure 2-1 on page 2-2. This modular architecture allows you the maximum flexibility in configuration, siting, and operation.The STRATA TX System key features are:• Analog, Digital, or Analog/Digital Switchable• MPEG Encoding (4:2:0, 4:2:2)• COFDM Modulation with Selectable Guard Band Interval• Digital Modulation for QPSK, 16 QAM, and 64 QAM• NTSC or PAL Modulation with Audio (4 mono or 2 stereo)• Tripod, Half Rack, or Full Rack Mounts• Front Panel Local Control• Remote Control• Bands from 3.4 to 13.25 GHz
Product Description 2-2STRATA TX Operator’s Guide/Tech Ref Manual Product Description 2-2STRATA TX Operator’s Guide/Tech Ref ManualFigure 2-1: STRATA TX System Block DiagramTCU TXUyNTSCyPALySDIyASIyIF RF OutTelemetry TelemetryDC Power and/or IF IN+28 VDCRS-2321.84 MHz OOK Tone+28 VDCRS-232The STRATA TX System TXU and the TCU may be operated in stand-alone configurations depending upon specific video applications.2.2.1 System OptionsThe STRATA TX System can be ordered configured for 1 of 11 specific RF bands as follows:• 3.4 to 3.9 GHz• 4.4 to 5.0 GHz• 6.4 to 7.1 GHz• 6.9 to 7.5 GHz• 7.4 to 8.1 GHz• 7.8 to 8.5 GHz• 8.2 to 8.9 GHz• 10.0 to 10.7 GHz• 10.5 to 11.2 GHz• 10.8 to 11.5 GHz• 12.7 to 13.25 GHzMRC is constantly working to expand and upgrade the capabilities of the STRATA TX System. Consult your Sales Representative or contact the factory for the latest band availability.The STRATA TX System (typically) consists of the following components:TXU The Transmitter Unit (TXU) can be equipped with either an FM Modulator or COFDM/MPEG module, but not both. A High Power Unit (HPU) is also contained within the TXU housing to increase RF power output.
Product Description 2-3STRATA TX Operator’s Guide/Tech Ref ManualTCU The Transmitter Control Unit (TCU) can be equipped with either an FM Modulator or COFDM/MPEG module, or both. ACU The optional AC to DC Power Converter (ACU) provides +28 VDC power from an AC power source to power one or more units in a system.Remote Control Panels Optional Remote Control Panels are available to allow remote control of the STRATA TX System from an instrument panel during airborne or mobile operations. 2.2.2 Single Unit SystemsThe TXU or TCU may be used independently in single-unit applications as follows:• The TXU may be used as a stand-alone transmitter accepting an IF input.• The TXU may be used as a stand-alone transmitter featuring FMT modulation or MPEG and COFDM.• The TCU may be used as a stand-alone unit used for FMT modulation or MPEG and COFDM, or both FMT modulation and MPEG and COFDM.2.2.3 Multi-Unit SystemsThe TXU and TCU can be configured as part of an integrated system as follows:• The TCU may contain the FMT modulator and MPEG/ COFDM module supplying an IF signal to a TXU containing only the RF transmitter.• The TXU may contain the RF modulator or MPEG/ COFDM module supplying an RF signal directly to the transmitter antenna.• The TCU can be separated from the TXU in applications where the transmitter needs to be placed in another location.2.2.4 Remote Control OptionsFor portable mobile or airborne operations, the STRATA TX System may be controlled by one of two models of Remote Control Panels. The Remote Control Panels are mounted in mobile racks or aircraft instrument panels and are connected via an RS-232 cable between the Remote Control Panel and the STRATA TX System.2.2.5 Antenna and Power Options The flexible architecture of the STRATA TX System allows a number of options for both the transmit antenna and the power.Antenna Options The STRATA TX System is fully compatible with the MRC family of transmit antennas, including:• OmniPole omnidirectional• Megahorn compact horn• SectorScan flat panel• MicroScan parabolic• Ellipse parabolicContact your Sales Representative to explore the wide array of antenna choices available.CAUTION To prevent damage to your STRATA TX System, MRC recommends using a +28 VDC power supply. Do not exceed +36 VDC input power or damage will occur.
Product Description 2-4STRATA TX Operator’s Guide/Tech Ref ManualPower Options The STRATA TX System configurations operate on +28 VDC power, supplied externally. This DC power can be supplied by the optional STRATA ACU, or from another DC power source. Contact your Sales Representative for the latest details.Note A TCU and TXU are defined as being “co-located” when the TXU and TCU are physically separated by not greater than 6 feet.If the TXU and TCU are co-located, power must be supplied to each unit through their individual power connectors from the same power source. See Figure 2-2. Do not use DC on coax to power the TXU or TCU when the units are co-located.Figure 2-2: Powering the TXU and TCU IndependentlyIf your installation calls for separating the TXU and TCU, the TXU is powered by DC supplied by the TCU or the TCU is powered by DC supplied by the TXU. The DC power is superimposed on the coaxial cable connected between the units. See Figure 2-3 and Figure 2-4. The DC input voltage to the unit co-located with the DC power STRATA TCUDC Power (+28 V)STRATA TXUBranched Power Cablesupply must be greater than +24 VDC. Refer to the “Installation” Chapter on page 6-1 (part of the STRATA TX Technical Reference Manual only) for additional information.For those applications that use a TCU in a standalone mode, i.e., to generate ASI or DVB-S signals, DC power from the TCU to the TXU or from the TXU to the TCU cannot be used.Figure 2-3: Powering the TXU from the TCUFigure 2-4: Powering the TCU from the TXUSTRATA TXUSTRATA TCUDC Power (+28 V)Up to 600 ft. (180 m)CoaxPower CableSTRATA TCUSTRATA TXUDC Power (+28 V )CoaxUp to 600 ft. (180 m)
Product Description 2-5STRATA TX Operator’s Guide/Tech Ref ManualDC power superimposed on the coaxial cable between a TCU and a TXU can be supplied from either the TCU or TXU, depending upon the location of the DC power supply. Coaxial cable length/voltage limitations exist when powering from either the TXU or TCU. These limitations are based on cable size, DC voltage input, cable resistance, and cable length. A maximum length of 600 feet (180 meters) between the TXU and TCU is supported. Contact MRC Technical Support for more information on cable requirements.DC power required for a STRATA TX System depends upon the TX System configuration, i.e., if the TXU or TCU are operated in a standalone mode, if the TXU and TCU are co-located, or if the TXU and TCU are mounted in separate locations. See Figure 2-5 on page 2-6 for the various STRATA TX System configurations available.For TX Systems that use DC power sources other than a STRATA ACU, contact MRC Technical Support for additional power information.2.2.6 Mounting and Deployment OptionsThe STRATA TX offers a number of options for either mobile or portable applications. For more details on installation of the STRATA TX in various applications, see the “Installation” Chapter on page 6-1 (part of the STRATA TX Technical Reference Manual only).Mobile Installation For mobile applications such as in a vehicle or in an aircraft, the STRATA TX System is usually mounted in an MRC fixed mounting bracket and is installed in a bulkhead or compartment. The cabling is permanently installed and power comes from aircraft or vehicle power. Portable Deployment In portable applications, the STRATA TX System will be moved from place to place and set up each time. The TXU and TCU will usually be mounted in a MRC universal mounting bracket. The bracket is attached to a tripod using a mounting plate and quick release. The cabling between the TXU and TCU is typically left in place and the power, antenna, and audio/video connections are removed at the end of each deployment. 2.2.7 System IntegrationSystem Communication When the TXU and TCU are connected, they automatically communicate via signals superimposed on the coaxial cable between the two units. This allows them to share information on installed hardware, preset configurations, current status, and alarms.System Operation Once the TXU and TCU are connected and communicating, the units work seamlessly together. System settings can be selected and modified from the front panel of either unit, regardless of which unit holds the hardware being configured. System Configuration The STRATA TX System offers two levels of system configuration, designed to match the needs of different personnel.For the field operator, the STRATA TX System has up to 9 Presets that can be selected from the front panel. Each Preset controls key parameters such as modulation, frequency, and audio and video settings. Additional settings that are front panel- controlled include band, channel, offset, and filtering.For the advanced operator and technical staff, the STRATA TX Configurator software allows complete control of all parameters in the STRATA TX System. The STRATA TX Configurator software runs on a Windows-based PC and connects to either the TXU or the TCU via an RS-232 serial interface cable.
Product Description 2-6STRATA TX Operator’s Guide/Tech Ref ManualInterfacing a PC to either the TXU or TCU in a connected system gives you complete control of both units. You can read the current settings, program new settings, or return the units to their factory default settings. The STRATA TX Configurator software automatically detects what hardware is installed in the system and assigns the appropriate configuration to the correct hardware, regardless of which unit holds the hardware being configured. Figure 2-5: STRATA TX System OptionsTXUTXUTXUTXUTXUTCUTCURXU 70 MHz IF Input Only NTSC or PAL Video with 4 Audio Channels AvailableSDI, ASI, NTSC, or PAL + Digitial/Analog Audio 3.4 to 13.25 GHz RF OutputSDI, ASI, NTSC, or PALVideo + Audio Analog Video or Digital Video + Audio Monitor MonitorRF/IF OnlyRF/IF OnlyRF/IF OnlyCOFDM / MPEGCOFDM / MPEG& FMTFMT OptionCOFDM / MPEG Option TXUTCURF/IF Only FMT Only NTSC or PAL Video with 4 Audio Channels Available
Product Description 2-7STRATA TX Operator’s Guide/Tech Ref Manual2.3 System ComponentsThis section will provide more details about each the components of a STRATA TX System:•STRATA TXU • STRATA TCU •STRATA ACU• STRATA Remote Control PanelsFor details on connections between the STRATA TX System components, refer to the “Installation” chapter (part of the STRATA TX Technical Reference Manual only).2.3.1 STRATA TXUThe TXU (Figure 2-6) always contains an IF/RF module that accepts either a 70 MHz COFDM, FMT IF, or external 70 MHz input signal and up-converts these signals to the required RF band. The RF frequency synthesizer circuit included in the IF/RF unit, in conjunction with the command and control power supply module, provides the means to channelize RF video and audio signals in the TX System RF band.The TXU, with either an analog (FMT) or digital (MPEG/COFDM) module, is integrated in the same housing as the HPU components. This provides the ability to incorporate high RF power output (12 watts of saturated RF power) into a single analog or digital transmitter assembly.Figure 2-6: STRATA TXUStandard U.S. FCC band plans, as well as customer-created channel plans, may be customized using the STRATA TX Configurator software.As noted previously, the TXU may also include either an MPEG/CODFM or FMT module (but not both), in which case the TXU serves as a stand-alone digital or analog video microwave transmission system. 2.3.2 STRATA TCUThe TCU (Figure 2-7 on page 2-8) may contain either analog or digital or both analog and digital video modulation modules. Where an application might initially employ only analog video transmission but expects to migrate to dual, switchable, analog and digital operation, the TCU may be upgraded to add the MPEG/COFDM module to add this capability.
Product Description 2-8STRATA TX Operator’s Guide/Tech Ref ManualFigure 2-7: STRATA TCUWhere only digital or analog video transmission is desired, the MPEG/COFDM or FMT modules may be installed in a TXU, thereby eliminating the need for a TCU. The STRATA TX design does not permit splitting digital and analog video modulator modules between a TXU and a TCU. A TCU may also consist of a stand-alone configuration whereby either or both MPEG/COFDM and FMT modules may be used independent of the TXU. This configuration permits use of a TCU equipped with analog and/or digital video modulation modules for a variety of signal input and output configurations, including a digital option using NTSC or PAL composite video input and ASI (digital) signal output. 2.3.3 STRATA ACUFor fixed or portable deployment applications, the STRATA TX System may be powered by the optional AC to DC Converter (ACU). Figure 2-8. Figure 2-8: AC to DC ConverterThe ACU installs as part of an integrated stack for either tripod or fixed applications. The ACU may also be used to power the TXU or TCU only when a TXU and TCU are not co-located. In this case, the TXU would receive DC power from the TCU or the TCU would receive DC power from the TXU superimposed on the coaxial cable connected between the units.In standalone TXU or TCU operations, the optional ACU may be used to supply DC power directly to the applicable unit. In the case where a TXU and a TCU are co-located, it is recommended that both the TXU and TCU be powered directly from the ACU in lieu of supplying DC power from the TCU to the TXU or from the TXU to the TCU via the coaxial cable connected between the units.2.3.4 STRATA Remote Control PanelsFor mobile or airborne operations, two Remote Control Panel models are currently available. Contact your Sales Representative for the latest information.Both Remote Control Panel models provide simplified transmit OUTPUTOUTPUT< >< >DCDC
Product Description 2-9STRATA TX Operator’s Guide/Tech Ref Manualoperations by allowing the operator or pilot to select either analog or digital pre-configured Presets, Channels, and Offsets, depending upon the required operating mode. Standard Remote Control Panel The standard STRATA Remote Control Panel (Figure 2-9) provides instrument panel remote control of the STRATA TX System for mobile operations and features 9 selectable Presets. For additional information, refer to the STRATA Remote Control Panel Operator’s Guide (part no. 400489).Figure 2-9: Standard Remote Control PanelAircraft Remote Control Panel The STRATA Aircraft Remote Control Panel (Figure 2-10) is a simplified version of the standard STRATA Remote Control Panel. This panel provides instrument panel remote control of the STRATA TX System for airborne operations. This model features only two Presets for ease of operation. The unit is designed to fit a standard aircraft instrument panel and provides user-friendly controls, combined with well placed and easy to read LED displays and color indicators.For additional information, refer to the STRATA Aircraft Remote Control Panel Operator’s Guide (part no. 400490).Figure 2-10: Aircraft Remote Control Panel2.4 TXU and TCU ConfigurationsTXU Different configurations of the TXU are available, depending upon if your TX System contains a standalone TXU or if your TX System contains both a TXU and TCU. The different configurations are described below.If your TXU is equipped with either an analog (FMT) module or a digital (MPEG/COFDM) module and was ordered to operate in a standalone mode without a TCU, the front panel will contain an AUDIO connector. See Figure 2-11 on page 2-10.
Product Description 2-10STRATA TX Operator’s Guide/Tech Ref ManualFigure 2-11: Standalone TXU ConfigurationIf your TXU was ordered to operate with a TCU, it will not contain either analog or digital modules and will therefore not contain an AUDIO connector. The AUDIO connector is replaced by a DC ON COAX switch. See Figure 2-12. The DC ON COAX switch allows manual control of DC power to the TXU from the TCU or from the TCU to the TXU via DC power superimposed on the coaxial cable connected between the two units.The rear of the TXU is identical on both configurations of the TXU, as shown in Figure 2-12. DO NOT EXCEED36 VOLTS DCFront ViewAUDIO ConnectorSIGNAL INPUT ConnectorPWR/RS-485 ConnectorFigure 2-12: TXU - TXU with TCU Configuration DO NOT EXCEED36 VOLTS DC DC ON COAXOFF ONRear ViewFront ViewDC ON COAX SwitchSIGNAL INPUT ConnectorPWR/RS-485 ConnectorRS-232 ConnectorRF Output Connector
Product Description 2-11STRATA TX Operator’s Guide/Tech Ref ManualTCU Several different configurations of the TCU also exist as the result of technical updates. Configuration differences are described below.TCU - Older Configuration If your TCU is an older configuration, the controls and connectors contained on the TCU are similar to those shown in Figure 2-13. Older configurations do not contain the front panel DC ON COAX override switch to provide manual control of DC power to a TXU.Figure 2-13: TCU - Older ConfigurationTCU - Newer Configuration If your TCU is the newer configuration, the controls and connectors contained on the TCU are similar to those shown in Figure 2-14. A DC ON COAX switch is located on the front panel to provide manual control of TCUTXXMITFront ViewRear ViewRS-232 Connector POWER ConnectorAUDIO ConnectorMonitor (MON) ConnectorSIGNAL IN ConnectorSIGNAL OUT ConnectorDC power to a TXU.Figure 2-14: TCU - Newer ConfigurationTCUTXXMITRear ViewFront View DC ON COAX SwitchSIGNAL IN ConnectorAUDIO ConnectorMonitor (MON) ConnectorSIGNAL OUT ConnectorPOWER ConnectorRS-232 Connector
Product Description 2-12STRATA TX Operator’s Guide/Tech Ref Manual2.5 Typical System ConfigurationsTypical STRATA TX System configurations are shown in Figure 2-15.Figure 2-15: STRATA TX System Configurations2.6 For More InformationAdditional detailed technical information about the STRATA TX System is contained in the STRATA TX Technical Reference Manual. Specific topics contained in the Technical Reference Manual are listed below:Topic ChapterInstallation See Chapter 6, “Installation”Connections to other equipmentSee Chapter 6, “Installation”Changing settings using the Configurator softwareSee Chapter 5, “Advanced Operation”Block Diagram See Chapter 9, “Theory of Operation”Supported Repairs See Chapter 7, “Repair”Repair Parts See Chapter 8, “Replacement Parts”
3 Routine Operation 3-1STRATA TX Operator’s Guide/Tech Ref ManualRoutine Operation3.1 Chapter OverviewThis chapter provides basic information that will enable you to operate your STRATA TX System. Here are the topics covered: Topic PageOverview of Controls, Indicators, and Connectors3-2TCU Controls, Indicators, and Connectors3-5TCU Controls, Indicators, and Connectors3-5ACU Controls, Indicators, and Connectors3-8STRATA Standard Remote Control Panel Controls, Indicators, and Connectors3-9STRATA Aircraft Remote Control Panel Controls, Indicators, and Connectors3-9Preparing for Operation 3-10Mobile Installation 3-10Portable Deployment 3-10Powering the STRATA TX System 3-12Single TCU Power Up and Power Down 3-13Single TXU Power up and Power Down 3-14TXU and TCU Power Up and Power Down - Co-Located3-15TXU and TCU Power Up and Power Down - Separate Locations3-17Information on settings made with the STRATA TX Configurator software can be found in the “Advanced Operation” Chapter on page 5-1 (part of the STRATA TX System Technical Reference Manual only). For a summary of settings that can be made with the TXU and TCU front panel control switches and which settings are made using the STRATA TX Configurator, see Section 3.7 on page 3-34.Using the STRATA TX Screens 3-19TXU and/or TCU Monitoring Operations 3-20Using the Monitor Screens in MPEG Output Mode3-20Using the Monitor Screens in Ext IF Input Mode3-22Using the Monitor Screens in COFDM - IF Mode3-23Using the Monitor Screens in COFDM ASI In Mode3-24Using the Monitor Screens in Analog - IF Mode3-25Using the Monitor Screens in DVB-S Mode3-26TXU and/or TCU Control Operations 3-27Changing a Preset 3-29Setting a Channel 3-30Setting Power Output 3-31Controlling TCU to TXU DC Power on Coax3-32Front Panel vs. STRATA TX Configurator Settings3-34
Routine Operation 3-2STRATA TX Operator’s Guide/Tech Ref Manual3.2 Overview of Controls, Indicators, and Connectors This section describes the controls, indicators, and connectors used on the STRATA TX System. 3.2.1 TXU Controls, Indicators, and ConnectorsControls, indicators, and connectors contained on the TXU are identified and described below. Topics covered are as follows: Each of these controls, indicators, and connectors are described in more detail in the following paragraphs. Controls, indicators, and connectors contained on the TXU front panel are shown in Figure 3-1. Connectors contained on the TXU rear panel are shown in Figure 3-2 on page 3-3. For configuration differences in the TXU, see “TXU and TCU Configurations” on page 2-9.Topic PageTXU Front Panel DC ON COAX Switch3-2TXU SIGNAL INPUT Connector 3-3TXU AUDIO Connector 3-3TXU Alphanumeric Display 3-3TXU XMIT LED 3-3TXU Status LED 3-4TXU PWR/RS-485 Connector 3-4TXU PWR Switch 3-4TXU Control Switch 3-4TXU RF Output Connector 3-5TXU RS-232 Connector 3-5Figure 3-1: TXU Controls, Indicators, and Connectors - Front ViewThe TXU is configured using Windows PC-based STRATA TX Configurator software. For details, see the “Advanced Operation” Chapter on page 5-1 (part of the STRATA TX System Technical Reference Manual only). TXU Front Panel DC ON COAX Switch DC ON COAX switches are not contained on all configurations of the TXU. For configuration differences, see Section 2.4 on page 2-9.If your STRATA TX System contains both a TXU and a TCU, the System allows you to power the TXU using DC power supplied from the TCU or allows you to power the TCU using DC power from the TXU. This DC power is superimposed on the coaxial cable between the TCU and the TXU. This DC power option is used when the TCU and the TXU must be deployed in two separate locations. DO NOT EXCEED36 VOLTS DC DC ON COAXOFF ONSIGNAL INPUT ConnectorAlpha- numeric DisplayStatus LEDDC ON COAX Switch or AUDIO ConnectorControl SwitchPower SwitchPWR/RS-485 ConnectorXMIT LED
Routine Operation 3-3STRATA TX Operator’s Guide/Tech Ref ManualFigure 3-2: TXU Controls, Indicators, and Connectors - Rear ViewWhen the TCU and TXU are co-located, MRC recommends both units be powered from the same DC power source.If your STRATA TX System does not contain a TCU, the DC ON COAX switch will not be present and an AUDIO connector will be mounted in place of the switch.If your STRATA TX System contains both a TXU and a TCU, the System gives you several ways to control DC power on the coaxial cable from the TCU to the TXU, depending on the configurations of your TCU and TXU: •The DC ON COAX switch on the front panel of the TCU (See Figure 3-3 on page 3-6) and the DC ON COAX switch on the front panel of the TXU (Figure 3-1 on page 3-2). RF Output ConnectorRS-232 Connector•The 75 Ohm Coax option on the Command Screen. Both control methods must be enabled for DC power to be operational if your TCU and TXU configurations both contain the DC ON COAX switches. If the DC ON COAX switch is not present on your TCU, DC power can only be applied using the 75 Ohm Coax option on the command screen. The TXU DC ON COAX switch must be set to ON in either situation.TXU SIGNAL INPUT Connector The BNC INPUT connector provides the IF or video input to the TXU.TXU AUDIO Connector AUDIO connectors are not contained on all configurations of the TXU. For configuration differences, see Section 2.4 on page 2-9. If your TXU contains an AUDIO connector, all audio inputs are applied to the front panel mounted 10-pin connector.TXU Alphanumeric Display The TXU contains a two-line by 12-character alphanumeric display. The display works in conjunction with the Control Switch to allow you to monitor system status and to control system settings. TXU XMIT LED When the TXU Control Switch is pressed for one second, the transmitter changes from the standby mode to the transmit mode or changes from the transmit mode to the standby mode. When the transmitter is in the transmit mode, the XMIT LED illuminates blue. When the transmitter is in the standby mode, the XMIT LED is off.If your STRATA TX System contains both a TXU and a TCU, pressing the Control switch on either the TXU or TCU will change the transmitter to the transmit mode or to the standby mode. The XMIT LED on both units will be on or off, depending
Routine Operation 3-4STRATA TX Operator’s Guide/Tech Ref Manualon the operating mode.TXU Status LED Above the PWR switch on both the TXU and TCU is a multi-color Status LED. The LED indications are as follows: WARNING A Major Alarm may also indicate a potential safety hazard. Shut down the STRATA TX System and disconnect power.TXU PWR/RS-485 Connector The TXU PWR/RS-485 connector mounted on the front panel of the unit allows the TXU to operate on external +28 VDC power sources.TXU PWR Switch The front panel PWR (power) switch controls application of DC power to the TXU. If your STRATA TX System contains both a TXU and an TCU, both PWR switches must be turned on for the system to function.TXU Control Switch Routine operating settings are controlled by the Control Switch. Turning the Control Switch right (cw) or left (ccw) displays status and settings and pressing it in makes LED Color Meaning----- Power is not on in that unit.Green Power is on and no errors are detected.Amber Minor Alarm - Power is on but some part of the system reports an abnormal condition that might impair performance.Red Major Alarm - Power is on but there is a failure or error that prevents normal operation.selections, as described below: Turning the Control Switch to the right (cw) displays the Monitor Screens. The Monitor Screens provide current status of the STRATA TX System, including:• Frequency Settings• Mode - Analog or Digital• Audio Settings• Video Settings• System Errors.Turning the Control Switch to the left (ccw) displays the Command Screens. The Command Screens allow control of the STRATA TX System, including:• Changing the Preset• Setting the RF Channel• Set Power Output• Select 75 Ohm Coax Power On or Power Off (Turns power from TCU to TXU or TXU to TCU on or off if DC power is superimposed on the coaxial cable between the TCU and the TXU).
Routine Operation 3-5STRATA TX Operator’s Guide/Tech Ref ManualTXU RF Output Connector The RF output connector is a type N connector that allows connection to an antenna.TXU RS-232 Connector The RS-232 connector provides connection to a Windows-based PC when using the STRATA TX Configurator software. This connector also provides connection to the STRATA Standard or Aircraft Remote Control Panel when used in mobile or aircraft operations. Pressing the Control Switch causes an action to occur. Command Screens• If the displayed setting is Chng Preset, Set Channel, or Set PowerOut, pressing the Control Switch causes the displayed setting to blink. Turning the Control Switch cw or ccw then displays the other options for that setting. When the desired option is displayed, pressing the Control Switch selects that option.• If the displayed setting is 75 Ohm Coax, pressing the Control Switch causes the setting to switch to the other choice (i.e., if 75 Ohm Coax Power Off is displayed, pressing the Control Switch will select 75 Ohm Coax Power On). Transmit• Pressing the Control Switch for one second changes the transmitter to the transmit mode from the standby mode.• Pressing the Control Switch for one second changes the transmitter from the transmit mode to the standby mode. 3.2.2 TCU Controls, Indicators, and ConnectorsControls, indicators, and connectors contained on the TCU are identified and described below. Topics covered are as follows: Each of these controls, indicators, and connectors are described in the following paragraphs. Controls, indicators, and connectors contained on the TCU are shown in Figure 3-3 on page 3-6. For configuration differences in the TCU, see “TXU and TCU Configurations” on page 2-9.The TCU is configured using Windows PC-based STRATA TX Configurator software. For details, see the “Advanced Operation” Chapter on page 5-1 chapter (part of the STRATA TX System Technical Reference Manual only). TCU Alphanumeric Display The TCU contains a two-line by 12-character alphanumeric display. The display works in conjunction with the Control Switch to allow you to monitor system status and to control system settings. Topic PageTCU Alphanumeric Display 3-6TCU XMIT LED 3-6TCU Status LED 3-6TCU PWR Switch 3-6TCU DC ON COAX Switch 3-6TCU Control Switch 3-7TCU RS-232 Connector 3-8TCU POWER Connector 3-8TCU SIGNAL OUT Connector 3-8TCU Monitor (MON) Connector 3-8TCU SIGNAL IN Connector 3-8TCU AUDIO Connector 3-8
Routine Operation 3-6STRATA TX Operator’s Guide/Tech Ref ManualFigure 3-3: TCU Controls, Indicators, and ConnectorsTCU XMIT LED When the TCU Control Switch is pressed for one second, the transmitter changes from the standby mode to the transmit mode or from the transmit mode to the standby mode. When the transmitter is in the transmit mode, the XMIT LED illuminates blue. When the transmitter is in the standby mode, the XMIT LED is off.If your STRATA TX System contains both a TXU and a TCU, pressing the Control switch on either the TXU or TCU will change the transmitter to the transmit mode or to the standby mode. The XMIT LED on both units will be on or off, depending TCUTXXMIT(Rear View)(Front View) DC ON COAX SwitchSIGNAL IN ConnectorMonitor (MON) ConnectorSIGNAL OUT ConnectorPOWER ConnectorRS-232 Connector AUDIO ConnectorAlphanumeric DisplayControl SwitchPWR SwitchStatus LEDXMIT LEDon the operating mode.TCU Status LED Above the PWR switch on both the TXU and TCU is a multi-color Status LED. The LED indications are as follows: WARNING A Major Alarm may also indicate a potential safety hazard. Shut down the STRATA TX System and disconnect power.TCU PWR Switch The front panel PWR (power) switch controls application of DC power to the TCU. If your STRATA TX System contains both a TXU and an TCU, both PWR switches must be turned on for the system to function.TCU DC ON COAX Switch DC ON COAX switches are not contained on all configurations of the TCU. For configuration differences, see “TXU and TCU Configurations” on page 2-9.If your STRATA TX System contains both a TXU and a TCU, the System allows you to power the TXU using DC power supplied from the TCU or to power the TCU using DC power from the TXU. This DC power is superimposed on the coaxial cable LED Color Meaning----- Power is not on in that unit.Green Power is on and no errors are detected.Amber Minor Alarm - Power is on but some part of the system reports an abnormal condition that might impair performance.Red Major Alarm - Power is on but there is a failure or error that prevents normal operation.
Routine Operation 3-7STRATA TX Operator’s Guide/Tech Ref Manualbetween the TCU and the TXU. This DC power option is used when the TCU and the TXU must be deployed in two separate locations. When the TCU and TXU are co-located, MRC recommends both units be powered from the same DC power source.If your STRATA TX System does not contain a TXU, the DC ON COAX switch may not be present. If the switch is present, it should be set to the OFF position.If your STRATA TX System contains both a TXU and a TCU, the System gives you several ways to control DC power on the coaxial cable between the TCU and the TXU, depending on the configurations of your TCU and TXU: •The DC ON COAX switch on the front panel of the TCU (See Figure 3-3 on page 3-6) and the DC ON COAX switch on the front panel of the TXU (See Figure 3-1 on page 3-2). •The 75 Ohm Coax option on the Command Screen. Both control methods must be enabled for DC power to be operational if your TCU and TXU configurations contain the DC ON COAX switches. If the DC ON COAX switch is not present on your TCU, DC power can only be applied using the 75 Ohm Coax option on the command screen. The TXU DC ON COAX switch must be set to ON in either situation.TCU Control Switch Routine operating settings are controlled by the Control Switch. Turning the Control Switch right (cw) or left (ccw) displays status and settings and pressing it in makes selections, as described below: Turning the Control Switch to the right (cw) displays the Monitor Screens. The Monitor Screens provide current status of the STRATA TX System, including:• Frequency Settings• Mode - Analog or Digital• Audio Settings• Video Settings• System Errors. Turning the Control Switch to the left (ccw) displays the Command Screens. The Command Screens allow control of the STRATA TX System, including:• Changing the Preset• Setting the RF Channel• Set Power Output• Select 75 Ohm Coax Power On or Power Off (Turns power from TCU to TXU or TXU to TCU on or off if DC power is superimposed on the coaxial cable between the TCU and the TXU).
Routine Operation 3-8STRATA TX Operator’s Guide/Tech Ref ManualTCU RS-232 Connector The RS-232 connector provides connection to a Windows-based PC when using the STRATA TX Configurator software. This connector also provides connection to the STRATA Standard or Aircraft Remote Control Panel when used in mobile or aircraft operations. TCU POWER Connector The TCU POWER connector Pressing the Control Switch causes an action to occur. Command Screens• If the displayed setting is Chng Preset, Set Channel, or Set PowerOut, pressing the Control Switch causes the displayed setting to blink. Turning the Control Switch cw or ccw then displays the other options for that setting. When the desired option is displayed, pressing the Control Switch selects that option.• If the displayed setting is 75 Ohm Coax, pressing the Control Switch causes the setting to switch to the other choice (i.e., if 75 Ohm Coax Power Off is displayed, pressing the Control Switch will select 75 Ohm Coax Power On). Transmit• Pressing the Control Switch for one second changes the transmitter to the transmit mode from the standby mode.• Pressing the Control Switch for one second changes the transmitter from the transmit mode to the standby mode. mounted on the rear panel of the unit allows the TCU to operate on external +28 VDC power sources.TCU SIGNAL OUT Connector The TNC type SIGNAL OUT connector provides ASI, CODFM - IF, IF, or IF composite video output signals, depending upon the options contained in the unit. In addition, if the TCU is used in conjunction with a separately located TXU, DC power to or from the TXU is superimposed on the output signal coaxial cable between the TXU and TCU.TCU Monitor (MON) Connector If your TCU has COFDM/MPEG installed, this rear panel output connector can be configured (when operating in the digital mode) to provide either:•70 MHz IF• ASI (output of COFDM modulator, before decoding)If your TCU is equipped with an analog modulator, this connector provides only the 70 MHz IF signal output.TCU SIGNAL IN Connector Video connections are made to the BNC SIGNAL IN connector. Video input selections are made by selecting Presets from the front panel Control Switch. Presets are created using the STRATA TX Configurator software. For more information, see the “Advanced Operation” Chapter on page 5-1 (part of the STRATA TX System Technical Reference Manual only).TCU AUDIO Connector Audio connections are made to the rear panel AUDIO connector.3.2.3 ACU Controls, Indicators, and ConnectorsControls, indicators, and connectors contained on the optional ACU are identified and described below. Topics covered are as
Routine Operation 3-9STRATA TX Operator’s Guide/Tech Ref Manualfollows: Each of the controls, indicators, and connectors are described in more detail in the following paragraphs. Controls, indicators, and connectors contained on the ACU are shown in Figure 3-4.ACU AC INPUT Connector The AC INPUT connector mounted on the rear panel of the unit provides external AC power to the unit.ACU POWER Switch The front panel POWER switch controls application of DC power to the DC OUTPUT connector. When the switch is set to I (on), DC power is present at the DC OUTPUT connector. When set to 0 (off), no output DC power is present at the DC OUTPUT connector. ACU Power LED The power LED is on when the POWER switch is set to I (on), indicating DC power is available at the DC OUTPUT connector. The indicator is off when the POWER switch is set to 0 (off).ACU DC OUTPUT Connector The DC OUTPUT connector mounted on the front panel of the unit provides +28 VDC power to the TCU and/or TXU. ACU FUSE The fuse provides overload protection for AC input power.Topic PageACU AC INPUT Connector 3-9ACU Power LED 3-9ACU Power LED 3-9ACU DC OUTPUT Connector 3-9ACU FUSE 3-9Figure 3-4: ACU Controls, Indicators, and Connectors3.2.4 STRATA Standard Remote Control Panel Controls, Indicators, and ConnectorsFor controls, indicators, and connectors contained on the optional Standard Remote Control Panel, refer to the STRATA Remote Control Panel Operator’s Guide, Document number 400489.3.2.5 STRATA Aircraft Remote Control Panel Controls, Indicators, and ConnectorsFor controls, indicators, and connectors contained on the optional STRATA Aircraft Remote Control Panel, refer to the STRATA Aircraft Remote Control Panel Operator’s Guide, Document number 400490. OUTPUTOUTPUT< >< >DCDCFUSEPOWER SwitchPower LEDDC OUTPUT ConnectorAC INPUT Connector
Routine Operation 3-10STRATA TX Operator’s Guide/Tech Ref Manual3.3 Preparing for OperationEach installation or deployment will have its own specific tasks according to the application and the installed hardware. 3.3.1 Mobile InstallationFor mobile applications such as aircraft or vehicle, the STRATA TX System is usually mounted in a bulkhead or compartment using an MRC Fixed Mounting Bracket (Figure 3-5). Mounting brackets are available to mount from one to three units.Figure 3-5: Fixed Mounting BracketThe cabling is permanently installed and power comes from aircraft (or vehicle) power.3.3.2 Portable DeploymentFor situations where you need to mount a STRATA TX System and its Fixed Mounting Bracket to an MRC tripod, MRC also offers a Quick Release. See Figure 3-6.For situations where you are mounting to another type of tripod that doesn’t directly accept the Quick Release, consult with MRC or your tripod manufacturer. MRC has Dovetail Adapter Plates that will convert some types of tripods to accept the Quick Release.Figure 3-6: Fixed Mounting Bracket on TripodFor portable applications where the STRATA TX System will be moved from place to place and set up each time, the system will usually be mounted in an MRC Universal Mounting Bracket. The Universal Mounting Bracket will then be attached to a Quick Release for easy mounting on an MRC tripod (See Figure 3-7 on page 3-11). Universal Mounting Brackets (See Figure 3-7 on page 3-11) are required for each unit in the STRATA TX System, i.e., TXU, TCU, and an optional ACU. For applications using multiple units such as a TXU, TCU, and an ACU, a Mounting Plate is also used to provide additional stiffness. The Mounting Plate (See Figure 3-7 on page 3-11) typically remains attached between the Universal Mounting Bracket and the Quick Release.The cabling between TX System units is also typically left in Fixed Mounting BracketQuick ReleaseMRC Tripod (Typical)
Routine Operation 3-11STRATA TX Operator’s Guide/Tech Ref Manualplace. The power, antenna and audio/video connections are usually removed at the end of each deployment. For portable deployment situations where you are mounting to another type of tripod that doesn’t directly accept the Quick Release, consult with MRC or your tripod manufacturer. MRC has Dovetail Adapter Plates that will convert some types of tripods to accept the Quick Release.Mounting to the Tripod Following are the general steps to mount a STRATA TX System to an MRC Tripod. These steps assume the TX System is already assembled into its Universal Mounting Bracket(s), and that the Mounting Plate and Quick Release are attached. Figure 3-7: Universal Mounting Bracket on Tripod Universal Mounting BracketMounting Plate (for TXU, TCU, and ACU)Quick ReleaseMRC Tripod (Typical)1. Attach the TX System to the Tripod using the Quick Release as shown in Figure 3-8. 2. Attach the antenna to the TXU using the Antenna Lock Plate, or connect a coaxial cable from the TXU to the antenna. See Figure 3-9 on page 3-12. Figure 3-8: Attaching Quick Release to Tripod 3. If you have both an TXU and a TCU, be sure they are connected to each other via coaxial cable. If you are unsure of the connections, refer to the “Installation” Chapter on page 6-1 (part of the STRATA TX System Technical Reference Manual only).4. Connect the STRATA TXU (and TCU, if present) to DC power of the correct voltage and polarity. Quick ReleaseTripod
Routine Operation 3-12STRATA TX Operator’s Guide/Tech Ref ManualIf you’re using a STRATA ACU, connect the AC input to AC power and connect the DC output to the TXU and TCU. If you are unsure of the power requirements or the connections, refer to the “Installation” Chapter on page 6-1 (part of the STRATA TX System Technical Reference Manual only).5. Connect the TXU (or TCU) inputs to your audio and video equipment.Figure 3-9: Complete Tripod InstallationUniversal Mounting BracketsAntenna (2 Options Shown)Quick ReleaseTXUTCUACUMounting PlateTripod (Typical)3.3.3 Powering the STRATA TX SystemThe STRATA TX System will be in one of two configurations which provide different options for controlling application of DC power between units. Model variations are as follows:Superimposing DC Power In this configuration, DC power is superimposed with the IF signals between units and there is no manual control of DC power from the TCU. The DC power is superimposed on the coaxial cable between the TCU and the TXU.To turn DC power on and off, the operator uses the TCU and TXU front panel PWR switches and either the TCU or TXU Control Switch and alphanumeric display menus. The TXU DC ON COAX switch must be set to ON.Superimposing DC Power with Manual Control In this configuration, DC power superimposed on the IF signals between the units is manually controlled. The operator can manually turn DC power on or off to the TXU from the TCU or to the TCU from the TXU and from the TXU to the HPU using DC ON COAX switches and TCU or TXU front panel Control Switches and alphanumeric display menus.The DC ON COAX switches provide the manual control and must be set to ON to allow application of DC power to the TXU , and TCU using the Control Switches and alphanumeric display menus.Powering STRATA TX Systems The method you use to power up your STRATA TX System will vary, depending upon the following:• The model of your STRATA TX System, whether or not you have DC power manual override control. • The transmitter configuration, whether you are using a single TCU, a single TXU, or a TCU and TXU
Routine Operation 3-13STRATA TX Operator’s Guide/Tech Ref Manual• Whether the TCU and TXU are to be co-located or physically separated over some distance.• Whether your STRATA TX System contains the optional AC to DC Power Converter (ACU). 3.3.4 Single TCU Power Up and Power DownIf your STRATA TX System consists of a single TCU, perform the following steps:CAUTION To avoid possible damage, turn off DC Power on the coax before connecting any test equipment.Power Up 1. Verify the power cable is properly connected to the TCU rear panel POWER connector.2. Verify all coaxial cables and connectors have been properly connected.3. Connect the TCU to DC power of the correct voltage and polarity. If you are unsure of the power requirements or the connections, refer to the “Installation” Chapter on page 6-1 (Part of the STRATA TX System Technical Reference Manual only). If the TCU is powered from the optional STRATA ACU, connect the ACU input to AC power and verify the TCU power cable is connected to the ACU DC OUTPUT connector. Set the ACU power switch to I (on) and verify the ACU power LED is on. If the TCU is powered from a source other than an ACU, turn that power source on. 4. Set the TCU PWR switch to I (on). 5. The normal power-up sequence is as follows: - The Status LED above the PWR switch should illuminate and should change colors from red, to green, to amber, and finally remain green. - The alphanumeric display should light up and quickly display a self-test screen, then the version of the installed firmware, and finally the Main Screen. Some typical screens are shown in Figure 3-10. The exact screens will vary depending on installed hardware.- The TCU will typically power up using the last settings in use when power was turned off.- If the TCU does not power up normally, refer to the “Troubleshooting” Chapter on page 4-1. Figure 3-10: Typical TCU Power Up Screens - Single TCUSTRATA TXV 0.1.1Preset 10.00WFirmware VersionMain Screen
Routine Operation 3-14STRATA TX Operator’s Guide/Tech Ref ManualPower Down 1. Set the TCU PWR switch to 0 (off).2. If the TCU is powered from the optional ACU, set the ACU power switch to 0 (off). If the TCU is powered from a source other than an ACU, turn that power source off.3.3.5 Single TXU Power up and Power DownIf your STRATA TX System consists of a single TXU, perform the following steps:CAUTION To avoid possible damage, turn off DC Power on the coax before connecting any test equipment.Power Up 1. Verify the power cable is properly connected to the TXU front panel POWER connector.2. Verify all coaxial cables and connectors have been properly connected.3. Connect the TXU to DC power of the correct voltage and polarity. If you are unsure of the power requirements or the connections, refer to the “Installation” Chapter on page 6-1 (Part of the STRATA TX System Technical Reference Manual only). If the TXU is powered from the optional STRATA ACU, connect the ACU input to AC power and verify the TXU power cable is connected to the ACU DC OUTPUT connector. Set the ACU power switch to I (on) and verify the ACU power LED is on. If the TXU is powered from a source other than an ACU, turn that power source on. 4. Set the TXU PWR switch to I (on). 5. The normal power-up sequence is as follows: - The Status LED above the PWR switch should illuminate and should change colors from red, to green, to amber, and finally remain green. - The alphanumeric display should light up and quickly display a self-test screen, then the version of the installed firmware, and finally the Main Screen. Some typical screens are shown in Figure 3-11 on page 3-15. The exact screens will vary depending on installed hardware.- The TXU will typically power up using the last settings in use when power was turned off.- If the TXU does not power up normally, refer to the “Troubleshooting” Chapter on page 4-1.
Routine Operation 3-15STRATA TX Operator’s Guide/Tech Ref ManualFigure 3-11: Typical TXU Power Up Screens - Single TXUPower Down 1. Set the TXU PWR switch to 0 (off).2. If the TXU is powered from the optional ACU, set the ACU power switch to 0 (off). If the TXU is powered from a source other than an ACU, turn that power source off.3.3.6 TXU and TCU Power Up and Power Down - Co-LocatedIf your STRATA TX System consists of a co-located TXU and a TCU, it is recommended that both the TCU and TXU be powered from the same DC power supply in lieu of using superimposed DC power on the coaxial cable between the TCU and the TXU. Note The following procedure reflects use of a single DC power source for both the TXU and TCU in lieu of using superimposed DC power on the coaxial cable between the TCU and the TXU.Perform the following steps to power up or power down a co-located TX System:STRATA TXV 0.1.1Preset 10.00WFirmware VersionMain Screen CAUTION To avoid possible damage, turn off DC Power on the coax before connecting any test equipment.Power Up 1. Verify the power cable is properly connected to the TCU rear panel POWER connector.2. Verify the power cable is properly connected to the TXU front panel POWER connector. Note If your TCU does not have a DC ON COAX switch, go to step 4. 3. Turn the recessed DC ON COAX switch on the front panel of the TCU until the screw slot of the switch points to OFF.4. Turn the recessed DC ON COAX switch on the front panel of the TXU until the screw slot of the switch points to OFF.5. Verify all coaxial cables and connectors have been properly connected.6. Connect the TCU and TXU to DC power of the correct voltage and polarity. If you are unsure of the power requirements or the connections, refer to the “Installation” Chapter on page 6-1 (Part of the STRATA TX System Technical Reference Manual only).
Routine Operation 3-16STRATA TX Operator’s Guide/Tech Ref ManualIf the TCU and TXU are both powered from the optional STRATA ACU, connect the ACU input to AC power and verify the TCU and TXU branched power cable is connected to the ACU DC OUTPUT connector. Set the ACU power switch to I (on) and verify the ACU power LED is on. If the TCU and TXU are powered from a source other than an ACU, turn that power source on. 7. Set the TCU PWR switch to I (on). 8. The normal power-up sequence is as follows: - The Status LED above the PWR switch should illuminate and should change colors from red, to green, to amber, and finally remain green. - The alphanumeric display should light up and quickly display a self-test screen, then the version of the installed firmware, and finally the Main Screen. Some typical screens are shown in Figure 3-12. The exact screens will vary depending on installed hardware.- The TCU will typically power up using the last settings in use when power was turned off.- If the TCU does not power up normally, refer to the “Troubleshooting” Chapter on page 4-1. 9. Set the TXU PWR switch to I (on). Figure 3-12: Typical TCU Power Up Screens - Co-Located TXU and TCU10. The normal power-up sequence is as follows: - The Status LED above the PWR switch should illuminate and should change colors from red, to green, to amber, and finally remain green. - The alphanumeric display should light up and quickly display a self-test screen, then the version of the installed firmware, and finally the Main Screen. Some typical screens are shown in Figure 3-13 on page 3-17. The exact screens will vary depending on installed hardware.- The TXU will typically power up using the last settings in use when power was turned off. If the TXU does not power up normally, refer to the “Troubleshooting” Chapter on page 4-1.STRATA TXV 0.1.1Preset 10.00WFirmware VersionMain Screen
Routine Operation 3-17STRATA TX Operator’s Guide/Tech Ref ManualFigure 3-13: Typical TXU Power Up Screens - Co-Located TXU and TCUPower Down 1. Set the TXU PWR switch to 0 (off).2. Set the TCU PWR switch to 0 (off).3. If the TXU and TCU are powered from the optional ACU, set the ACU power switch to 0 (off). If the TCU and TXU are powered from a source other than an ACU, turn that power source off.3.3.7 TXU and TCU Power Up and Power Down - Separate LocationsIf your STRATA TX System consists of a TXU and a TCU and the TCU is located in a separate location from the TXU, the TXU will be powered using the superimposed DC power on the coaxial cable between the TCU and the TXU or the TCU will be powered using DC power superimposed on the coaxial cable from the TXU. STRATA TXV 0.1.1Preset 10.00WFirmware VersionMain Screen Perform the following steps to power up or power down a separately located TXU and TCU TX System:CAUTION To avoid possible damage, turn off DC Power on the coax before connecting any test equipment.Power Up 1. Verify the power cable is properly connected to the TCU rear panel POWER connector. Note If your TCU does not have a DC ON COAX switch, go to step 3. 2. Turn the recessed DC ON COAX switch on the front panel of the TCU until the screw slot of the switch points to ON.3. Turn the recessed DC ON COAX switch on the front panel of the TXU until the screw slot of the switch points to ON.4. Verify all coaxial cables and connectors have been properly connected.Note When the TCU and TXU are mounted in separate locations, it is recommended that DC input power be connected to the TXU. Since either unit may be powered from the other unit via DC power superimposed on the coaxial cable between the units, DC input power may therefore be applied to either the TXU or the TCU.
Routine Operation 3-18STRATA TX Operator’s Guide/Tech Ref Manual5. Connect the TCU or TXU to DC power of the correct voltage and polarity. If you are unsure of the power requirements or the connections, refer to the “Installation” Chapter on page 6-1 chapter (Part of the STRATA TX System Technical Reference Manual only). If the TCU/TXU is powered from the optional STRATA ACU, connect the ACU input to AC power and verify the TCU/TXU power cable is connected to the ACU DC OUTPUT connector. Set the ACU power switch to I (on) and verify the ACU power LED is on. If the TCU is powered from a source other than an ACU, turn that power source on. 6. Set the TCU PWR switch to I (on). 7. The normal power-up sequence is as follows: - The Status LED above the PWR switch should illuminate and should change colors from red, to green, to amber, and finally remain green. - The alphanumeric display should light up and quickly display a self-test screen, then the version of the installed firmware, and finally the Main Screen. Some typical screens are shown in Figure 3-14. The exact screens will vary depending on installed hardware.- The TCU will typically power up using the last settings in use when power was turned off.- If the TCU does not power up normally, refer to the “Troubleshooting” Chapter on page 4-1. Figure 3-14: Typical TCU Power Up Screens - Separately Located TXU and TCU8. Rotate the TCU Control Switch ccw until the 75 Ohm Coax option (Figure 3-15) is displayed on the alphanumeric display. Figure 3-15: 75 Ohm Coax Option9. Press Control Switch to change Power Off to read Power On, as required.10. Set the TXU PWR switch to I (on). 11. The normal power-up sequence is as follows: - The Status LED above the PWR switch should illuminate and should change colors from red, to green, to amber, and finally remain green. - The alphanumeric display should light up and quickly display a self-test screen, then the version of the STRATA TXV 0.1.1Preset 10.00WFirmware VersionMain Screen 75 Ohm CoaxPower Off
Routine Operation 3-19STRATA TX Operator’s Guide/Tech Ref Manualinstalled firmware, and finally the Main Screen. Some typical screens are shown in Figure 3-16. The exact screens will vary depending on installed hardware.- The TXU will typically power up using the last settings in use when power was turned off.- If the TXU does not power up normally, refer to the “Troubleshooting” Chapter on page 4-1.Figure 3-16: Typical TXU Power Up Screens - Co-Located TXU and TCUPower Down 1. Set the TXU PWR switch to 0 (off).2. Set the TCU PWR switch to 0 (off).3. If the TCU/TXU is powered from the optional ACU, set the ACU power switch to 0 (off). If the TCU/TXU is powered from a source other than an ACU, turn that power source off.STRATA TXV 0.1.1Preset 10.00WFirmware VersionMain Screen 3.4 Using the STRATA TX ScreensAs you use the STRATA TX System, you will interact extensively with the TXU and/or TCU screens. Following are some points to make this easier.Main Screen The Main Screen is your starting point for navigating through the Monitor and Control screens. The Main Screen provides the current values of the Preset selected and the selected Preset output power level. When the STRATA TX System completes its power-up sequence, it will display the Main Screen. A typical Main Screen is shown in Figure 3-17.Figure 3-17: Typical STRATA TX Main Screen Accessing the Main Screen You can access the Main Screen at any time by scrolling to the end of the screens you are viewing (either Monitor or Control). Your next click of the Control Switch will bring up the Main Screen. Accessing the Monitor Screen You can access the Monitor Screens at any time by turning the Control Switch clockwise (cw). Accessing the Control Screen You can access the Control Screen at any time by turning the Control Switch counter-clockwise (ccw). Preset 3 . WCurrently Selected PresetOutput Power Level
Routine Operation 3-20STRATA TX Operator’s Guide/Tech Ref ManualDefault to Main Screen If you do not turn or push the Control Switch for a period of about 7 seconds, the display will default to the Main Screen.If you turn the Control Switch within those 7 seconds, you will continue scrolling within that set of screens (Monitor or Control).Unit vs.System Control If you’re using a standalone TXU or TCU, the menus and options that appear on the display will be based on the hardware option(s) installed in that individual unit. When you connect your TCU and TXU, the two units automatically detect what hardware is installed in each unit, and automatically configure the menus and options to match the installed hardware. The connected STRATA TX System then allows you to control the entire system from either the TXU or the TCU front panel.3.5 TXU and/or TCU Monitoring OperationsThe STRATA TX System Presets are set to six possible modes of operation, based on the options contained in your TXU and/or TCU. These operating modes are established using the STRATA TX Configurator software. The operating mode options available via the Configurator software are as follows:• MPEG Only ASI Out (MPEG Output mode) (Standalone TCU Operation Only)• External 70MHz IF In (Ext IF Input mode)• MPEG/COFDM IF Out (COFDM - IF mode)• COFDM Only - ASI In (COFDM ASI In mode)• Analog IF Output (Analog - IF mode)• DVB-S (Satellite) (DVB-S mode) (Standalone TCU Operation Only)The options displayed on the Monitor Screens are in bold fonts.Once the STRATA TX System is set up and powered up, you will be able to check its configuration and monitor its operation.The following sections describe how to use the Monitor Screens and how to monitor the quality of the microwave link. 3.5.1 Here are the tasks described: 3.5.2 Using the Monitor Screens in MPEG Output ModeWhen the STRATA TX System Preset selected is operating in the MPEG Output mode, a DVB ASI transport stream is supplied to the signal output connector and the monitor output connector. The MPEG Output mode is only available when the TCU is operated in a standalone configuration.Topic PageUsing the Monitor Screens in MPEG Output Mode3-20Using the Monitor Screens in Ext IF Input Mode3-22Using the Monitor Screens in COFDM - IF Mode3-23Using the Monitor Screens in COFDM ASI In Mode3-24Using the Monitor Screens in Analog - IF Mode3-25Using the Monitor Screens in DVB-S Mode3-26
Routine Operation 3-21STRATA TX Operator’s Guide/Tech Ref Manual Routine Operation 3-21STRATA TX Operator’s Guide/Tech Ref ManualSee Figure 3-18 for the MPEG Output Monitor Menu Map.Figure 3-18: MPEG Output Monitor Menu Map
Routine Operation 3-22STRATA TX Operator’s Guide/Tech Ref Manual Routine Operation 3-22STRATA TX Operator’s Guide/Tech Ref Manual3.5.3 Using the Monitor Screens in Ext IF Input ModeWhen the STRATA TX System is operating in the Ext IF Input mode, the 70 MHz IF input signal from the input connector is routed through the TCU to the TXU (if present).See Figure 3-19 for the Ext IF Monitor Map.Figure 3-19: Ext IF Input Monitor Map
Routine Operation 3-23STRATA TX Operator’s Guide/Tech Ref Manual Routine Operation 3-23STRATA TX Operator’s Guide/Tech Ref Manual3.5.4 Using the Monitor Screens in COFDM - IF ModeWhen the STRATA TX System is operating in the COFDM - IF mode, 70 MHz COFDM IF output from the internal COFDM/MPEG board is supplied to the output and monitor ports and to the TXU, if present.See Figure 3-20 for the COFDM - IF Monitor Menu Map. Figure 3-20: COFDM - IF Monitor Menu Map
Routine Operation 3-24STRATA TX Operator’s Guide/Tech Ref Manual Routine Operation 3-24STRATA TX Operator’s Guide/Tech Ref Manual3.5.5 Using the Monitor Screens in COFDM ASI In ModeWhen the STRATA TX System is operating in the COFDM ASI In mode, the internal MPEG encoder is bypassed and an externally supplied ASI stream is routed to the monitor and output connectors and then to the TXU, if present.See Figure 3-21 for the COFDM ASI In Menu Map.Figure 3-21: COFDM ASI In Monitor Map
Routine Operation 3-25STRATA TX Operator’s Guide/Tech Ref Manual Routine Operation 3-25STRATA TX Operator’s Guide/Tech Ref Manual3.5.6 Using the Monitor Screens in Analog - IF ModeWhen the STRATA TX System is operating in the Analog - IF mode, 70 MHz FM output is routed to the TXU, if present. This option is only available if the FMT option is installed.See Figure 3-22 for the Analog - IF Monitor Menu Map.Figure 3-22: Analog - IF Monitor Menu Map
Routine Operation 3-26STRATA TX Operator’s Guide/Tech Ref Manual Routine Operation 3-26STRATA TX Operator’s Guide/Tech Ref Manual3.5.7 Using the Monitor Screens in DVB-S ModeWhen the STRATA TX System is operating in the DVB-S mode, this mode utilizes a single carrier modulator and supplies a configurable DVB-S signal to the TCU signal output and monitor connectors. This mode is operational for QPSK, 16 QAM, and 8 PSK modulation formats. This mode is used for standalone TCU operations only.See Figure 3-23 for the DVB-S Monitor Menu Map.Figure 3-23: DVB-S Monitor Menu Map
Routine Operation 3-27STRATA TX Operator’s Guide/Tech Ref Manual3.6 TXU and/or TCU Control OperationsThis section describes how to configure your STRATA TX System using the front panel Control Switch. Turning the front panel Control Switch counterclockwise on either the TXU or TCU controls transmitter functions including changing Presets, changing RF channel assignments, setting RF attenuation levels, and activation of DC power from a TCU to a separately located TXU, or from a TXU to a separately located TCU.Settings may be changed on a standalone TCU, a standalone TXU, or a TXU and TCU TX System. For a summary of settings that can be changed using the front panel Control Switch and which are made using the STRATA TX Configurator software, see “Front Panel vs. STRATA TX Configurator Settings” on page 3-34. Here are the tasks described:Refer to Figure 3-24 on page 3-28 for the Control Menu Map.Topic PageChanging a Preset 3-29Setting a Channel 3-30Setting Power Output 3-31Controlling TCU to TXU DC Power on Coax3-32
Routine Operation 3-28STRATA TX Operator’s Guide/Tech Ref ManualFigure 3-24: Control Menu Map Changing a Preset
Routine Operation 3-29STRATA TX Operator’s Guide/Tech Ref Manual3.6.1 Changing a PresetThe STRATA TX is designed to enable you to control operating settings through Presets stored in the transmitter. The STRATA TCU and TXU are shipped with factory Presets and can be customized for the user. Your STRATA TX System can be pre-configured with up to 9 Presets. Each Preset contains most of the operating settings needed to control the STRATA TX System. System Presets can only be defined and changed using the STRATA TX Configurator software. Presets cannot be changed from the TXU or TCU front panels.For information on configuring Presets, see the “Configurator Reference” Appendix on page C-1 (part of the STRATA TX Technical Reference Manual only).Notes When you change a Preset, the new Preset remains in effect. When the TX System is powered down, that Preset is active when the TX System is powered up again. When a Preset is changed, the Channel does not change. When a Channel is changed, the Preset does not change.To change Presets, perform the following steps: 1. Verify the STRATA TX System is connected and powered up. See ”Powering the STRATA TX System” on page 3-12.2. Observe the Main Screen (Figure 3-25) is displayed.Figure 3-25: Main Screen - Changing a Preset 3. Turn the Control Switch ccw until the display reads Chng Preset.Note Changing Presets when the TX System is in the transmit mode will place the transmitter in the standby mode when the Control Switch is pressed.4. Press the Control Switch to select Chng Preset. See Figure 3-26.Figure 3-26: Change Preset Screen (Typical)5. Observe the current Preset setting begins to blink.6. Turn the Control Switch cw or ccw until the desired Preset is displayed. 7. Press the Control Switch once to select that Preset.8. Observe display changes back to the Main Screen after a short delay.9. Observe newly selected Preset is displayed on Main Screen. See Figure 3-27 on page 3-30. Preset 3 . WChng Preset Preset 1 Blinking
Routine Operation 3-30STRATA TX Operator’s Guide/Tech Ref ManualFigure 3-27: Main Screen (Typical) - Preset Changed10. Press the Control Switch for one second to place the TX System in the transmit mode, as required.3.6.2 Setting a ChannelThe STRATA TX Channel and Offset, other than the Preset Channel pre-programmed using the STRATA TX Configurator software, can be selected from the TXU or TCU front panel and can be configured for operation on any of up to 10 Channels, with (+) and (-) offsets. For more information, see the “Channels & Frequencies” Appendix on page A-1.The frequencies assigned to each Channel must be configured using the STRATA TX Configurator software. The frequencies cannot be changed from either the TXU or TCU front panels. For information on configuring Channels, see the “Configurator Reference” Appendix on page C-1 (part of the STRATA TX System Technical Reference Manual only).Preset . WNew PresetNotes The Preset will retain the new Channel until the TX System is powered off. When the TX System is powered up again, the original Channel setting will be restored. When a Preset is changed, the Channel does not change. When a Channel is changed, the Preset does not change. To select which Channel to modify, perform the following steps: 1. Verify the STRATA TX System is connected and powered up. See ”Powering the STRATA TX System” on page 3-12.2. Observe the Main Screen (Figure 3-28) is displayed.Figure 3-28: Main Screen 3. Turn the Control Switch ccw until the display reads Set Channel. See Figure 3-29.Figure 3-29: Change a Channel (Typical) Preset 3 . WSet ChannelNot On Chnl
Routine Operation 3-31STRATA TX Operator’s Guide/Tech Ref ManualNote Changing Channels when the TX System is in the transmit mode will place the transmitter in the standby mode when the Control Switch is pressed.4. Press the Control Switch once to select Set Channel and observe the Channel selected begins to blink. 5. Turn the Control Switch cw or ccw until the desired Channel and Offset are displayed. 6. Press the Control Switch once to select that Channel and Offset.7. Observe the display changes back to the Main Screen after a short delay. 8. Press the Control Switch for one second to place the TX System in the transmit mode, as required.3.6.3 Setting Power Output The power output of your STRATA TX System can be set by controlling the attenuation, in dB, from either the TXU or TCU front panel. Note Maximum power output occurs with 0 dB of attenuation selected. Attenuation levels from 0 dB to -31 dB may be selected in 1 dB increments.To select power output attenuation, perform the following steps:1. Verify the STRATA TX System is connected and powered up. See ”Powering the STRATA TX System” on page 3-12.2. Observe the Main Screen (Figure 3-30) is displayed.Figure 3-30: Main Screen (Typical) - Power Output3. Turn the Control Switch ccw until the display reads Set PowerOut. See Figure 3-31.Figure 3-31: Change Power Output (Typical)Notes Changing power output attenuation when the TX System is in the transmit mode will place the transmitter in the standby mode when the Control Switch is pressed. Output power attenuation level must be reset or verified whenever Presets are changed . 4. Press the Control Switch once and observe the ATTN: dB line begins to blink.5. Turn the Control Switch cw or ccw until the desired attenuation level is displayed.6. Press the Control Switch to select the power output attenuation level.7. Observe the new attenuation level is displayed.8. After a short delay, observe the Main Screen is displayed.Preset 3 . WSet PowerOutAttn: dB
Routine Operation 3-32STRATA TX Operator’s Guide/Tech Ref Manual9. Press the Control Switch for one second to place the TX System in the transmit mode, as required. 3.6.4 Controlling TCU to TXU DC Power on Coax If your STRATA TX System requires the TXU and TCU to be mounted in separate locations, MRC recommends powering the TCU via the coaxial cable from the TXU. Note When the TCU and TXU are mounted in separate locations, it is recommended that DC input power be connected to the TXU. Since either unit may be powered from the other unit via DC power superimposed on the coaxial cable between the units, DC input power may therefore be applied to either the TXU or the TCU.If your TXU and TCU configurations contain DC ON COAX switches mounted on the units, these switches must be set to ON in addition to controlling DC power superimposed on the coaxial cable from the TXU to the TCU or from the TCU to the TXU. To apply DC power from the TXU to the TCU superimposed on the coaxial cable between the two units, perform the following steps.Notes This procedure must only be performed on STRATA TX Systems where the TXU and TCU are physically mounted in separate locations. This procedure may be performed using either the TXU or TCU Control Switch and display.Apply DC Power on Coax 1. Verify the STRATA TX System is connected and powered up. See ”Powering the STRATA TX System” on page 3-12.2. Observe the Main Screen (Figure 3-32) is displayed.Figure 3-32: Main Screen Note If your TCU does not contain a DC ON COAX switch, go to step 4.3. Turn the recessed DC ON COAX switch on the front panel of the TCU until the screw slot points to OFF.4. Turn the recessed DC ON COAX switch on the front panel of the TXU until the screw slot points to OFF.5. Turn the Control Switch ccw until the display reads 75 Ohm Coax. See Figure 3-33.Figure 3-33: 75 Ohm CoaxPreset 3 . W75 Ohm CoaxPower Off
Routine Operation 3-33STRATA TX Operator’s Guide/Tech Ref ManualNote Pressing the Control Switch to select application of DC power on the coaxial cable from the TXU to the TCU or from the TCU to the TXU when the TX System is in the transmit mode will place the transmitter in the standby mode.6. Press the Control Switch one time to change Power Off to Power On.7. After a short delay, observe the Main Screen is displayed.8. Press the Control Switch for one second to place the TX System in the transmit mode, as required.Remove DC Power on Coax Note This procedure may be performed using either the TXU or TCU Control Switch and display.1. Observe the Main Screen is displayed.2. Turn the Control Switch ccw until the display reads 75 Ohm Coax.3. Press the Control Switch one time to change the display from Power On to Power Off.4. After a short delay, observe the Main Screen is displayed.Note If your TCU does not contain a DC ON COAX switch, go to step 6.5. Turn the recessed DC ON COAX switch on the front panel of the TCU until the screw slot points to ON.6. Turn the recessed DC ON COAX switch on the front panel of the TXU until the screw slot points to ON.
Routine Operation 3-34STRATA TX Operator’s Guide/Tech Ref Manual3.7 Front Panel vs. STRATA TX Configurator SettingsThe design of the STRATA TX System and STRATA TX Configurator software makes commonly available settings accessible from the TXU and/or TCU front panel and more advanced settings accessible through the STRATA TX Configurator.A summary of settings that can be controlled by each method is shown in Table 3-1.Table 3-1: Front Panel vs. Configurator Settings Parameter AvailableSettingsSet Using Control SwitchSet Using TX ConfiguratorPresetsPreset in use 1, 2,... 9 ✔ ✔Preset text Any 12 alphanumeric characters✔Operation Mode • MPEG Output ✔• Ext IF Input ✔•COFDM-IF ✔• COFDM ASI In✔• Analog - IF ✔• DVB-S ✔Color Bars • PAL ✔•NTSC ✔•OFF ✔•Auto ✔IF CW Tone • ON ✔•OFF ✔ChannelsChannel & Offset in use• 1 thru 10 ✔• -, Center, + ✔Channel & Offset frequenciesDepends on band ✔DC PowerDC On Coax (75 Ohm Coax)• Power Off ✔• Power On ✔COFDM COFDM Bandwidth•6 MHz ✔•7 MHz ✔•8 MHz ✔COFDM Modulation (MPEG Out and COFDM ASI In Modes)• QSPK ✔• 16 QAM ✔• 64 QAM ✔Table 3-1: Front Panel vs. Configurator Settings (Continued)Parameter AvailableSettingsSet Using Control SwitchSet Using TX Configurator
Routine Operation 3-35STRATA TX Operator’s Guide/Tech Ref ManualCOFDM Modulation (DVB-S Mode) • QSPK ✔• 16 QAM ✔•8 QAM ✔COFDM Guard Interval•1/32 ✔•1/16 ✔•1/8 ✔•1/4 ✔COFDM Symbol Rate• (Variable) ✔COFDM Roll Off Factor•0.25 ✔•0.35 ✔MPEGAudio A Type • OFF ✔• MPEG ✔• Linear ✔Audio B Type • OFF ✔• MPEG ✔• Linear ✔Audio A Mode • Stereo ✔• Dual Mono ✔Table 3-1: Front Panel vs. Configurator Settings (Continued)Parameter AvailableSettingsSet Using Control SwitchSet Using TX ConfiguratorAudio B Mode • Stereo ✔• Dual Mono ✔BISS • OFF ✔•BISS-1 ✔•BISS-E ✔Video Input • NTSC No Pedestal✔• SDI 525 In ✔• NTSC In ✔Chroma Format • 4:2:0 ✔•4:2:2 ✔Delay Mode • Standard ✔• Low ✔Wayside Channel State•OFF ✔• IRD Comp ✔•STRATA Comp.✔FMT Video Deviation • 3 MHz ✔•4 MHz ✔Low Pass Filter • On ✔•Off ✔Table 3-1: Front Panel vs. Configurator Settings (Continued)Parameter AvailableSettingsSet Using Control SwitchSet Using TX Configurator
Routine Operation 3-36STRATA TX Operator’s Guide/Tech Ref ManualAudio Channel 1 thru 4 Frequency• 4830 kHz ✔• 5200 kHz ✔• 5800 kHz ✔• 6200 kHz ✔• 6800 kHz ✔• 7020 kHz ✔• 7500 kHz ✔• 8065 kHz ✔• 8300 kHz ✔• 8590 kHz ✔Audio Channel Frequency Enabled• Selected ✔• Not selected ✔De emphasis • Selected ✔• Not selected ✔Table 3-1: Front Panel vs. Configurator Settings (Continued)Parameter AvailableSettingsSet Using Control SwitchSet Using TX Configurator
4 Troubleshooting 4-1STRATA TX Operator’s Guide/Tech Ref ManualTroubleshooting4.1 Chapter OverviewThis chapter describes how to troubleshoot your STRATA TX System. Here are the topics covered:4.2 Status LEDAbove the PWR switch on both the TXU and TCU is a multi-color Status LED. The LED indications are listed in Table 4-1. Topic PageStatus LED 4-1Messages on Display 4-1Error Codes 4-3Operational Problems 4-8 WARNING A Major Alarm may also indicate a potential safety hazard. Shut down the STRATA TX System and disconnect power.4.3 Messages on DisplayOne of the ways the STRATA TX System will alert you to problems is by error messages on the TXU and/or TCU front panel displays. These are displayed on the Monitor Screens. See Table 4-2 on page 4-2 for descriptions of the messages and what to do when they appear.Table 4-1: Status LED IndicationsLED Color Meaning Suggested Action----- Power is not on in that unit. Turn on power, as required.Green Power is on and no errors are detected.None.Amber Minor Alarm - Power is on but some part of the system reports an abnormal condition that requires attention. Condition might impair performance. Check Monitor Screens for error messages or Error Codes. Troubleshoot using tables in this chapter.Red Major Alarm - Power is on but there is a serious failure or error that will prevent normal operation. The internal processors are not running.Turn off unit and disconnect power.
Troubleshooting 4-2STRATA TX Operator’s Guide/Tech Ref ManualTable 4-2: Display Messages Message Meaning Suggested Operator Action Suggested Technical Staff ActionNot On Chnl Channel frequencies defined in the Channel Plan for that band are not being recognized. Contact technical staff. • Use STRATA TX Configurator to check settings. Check the Channel Plan to be sure it is correct. Verify Channel Plan matches the transmitter settings.• If message persists even when operating on a frequency that matches the channel plan, unit may have suffered internal failure. Call MRC Technical Support.No Video The TX is unable to lock on video signal.• Check cable connection between antenna and TX System.• Check cable connection between TXU and TCU.• Contact technical staff.• Use STRATA TX Configurator to check settings. • If message persists, unit may have suffered internal failure. Call MRC Technical Support.
Troubleshooting 4-3STRATA TX Operator’s Guide/Tech Ref Manual4.4 Error CodesThe STRATA TX has an extensive library of diagnostic Error Codes to help you pinpoint any problems. These Error Codes:• Are displayed on the front panel display, on the Error Code Screen. • Cause the Status LED to glow amber, alerting you to investigate the problem.The Error Codes are formatted into 2 groups of characters, as described in Figure 4-1.4.4.1 Primary Error CodeThe first group of characters is the Primary Error Code. In most cases this portion of the Error Code will uniquely identify the problem.See Table 4-3 on page 4-4 for descriptions of the error codes and what to do when they appear.Figure 4-1: Error Code FormatE141 41 Primary Error CodeIdentifies error condition. See Section 4.4.1 .Unit IDIdentifies unit reporting error. See Section 4.4.3 on page 4-8.Error StatusDepends on error code. See Section 4.4.2 on page 4-8.
Troubleshooting 4-4STRATA TX Operator’s Guide/Tech Ref ManualTable 4-3: Primary Error Codes Error Code Meaning Suggested Operator Action Suggested Technical Staff ActionStatus Errors(Some part of System is reporting an abnormal condition.)E020 TXU IF Fault • Verify condition of all cable connections.• Contact technical staff.Call MRC Technical Support.E021 TXU RF Fault • Verify condition of all cable connections.• Contact technical staff.Call MRC Technical Support.E0E0 FMT Video PLL Unlocked Note - This error will appear only if the TX System contains the FMT option.• Contact technical staff.• Verify video input is at the correct level.• Call MRC Technical Support.E0E1 FMT Audio 1 PLL Unlocked Note - These errors will appear only if the TX System contains the FMT option.• Check FMT settings using Monitor Screens and Command Screens. Settings must match transmitter settings.• Contact technical staff.• Use STRATA TX Configurator to check FMT settings. Be sure all settings match the transmitter settings.• Use STRATA TX Configurator to reprogram all the settings in the radio. • If problem persists, possible hardware failure. Call MRC Technical Support.E0E2 FMT Audio 2 PLL UnlockedE0E3 FMT Audio 3 PLL UnlockedE0E4 FMT Audio 4 PLL Unlocked
Troubleshooting 4-5STRATA TX Operator’s Guide/Tech Ref ManualE080 Communication Failure with the COFDM/MPEG UnitNote - This error will appear only if the TX System contains the COFDM/MPEG option.• If the TX System contains a standalone TXU or TCU, contact technical staff.• If the TX System contains both a TXU and a TCU, verify condition of cable connections. Contact technical staff.If problem persists, possible hardware failure. Call MRC Technical Support.Parameter Errors(Some internal parameter is outside of allowable limits.)E030 TXU 2.048 Volt Reference Error • Check for Error Codes related to power - E035 thru E039 and E03A thru E03E. Correct power problem.• Contact technical staff.If errors persist with correct power connected, unit has suffered internal failure. Call MRC Technical Support.E031 TXU 5.5 Volt Reference ErrorE032 TXU 7 Volt Line ErrorE033 TXU 11 Volt Line ErrorE034 TXU Temperature Error Note - TXU internal fans operate only when TX System is transmitting. Fan operation can be determined by listening for audible fan noise or by feeling for airflow at rear of TXU when TX System is in transmit mode.• Verify TXU internal fans are operating when TX System is transmitting.• Check TXU to be sure it is not too close to sources of heat. Relocate TXU, if possible.• Verify TXU has room around it for air circulation. Move objects preventing air flow. • Contact technical staff.If errors persist with proper location and airflow and correct power is connected, unit has suffered internal failure. Call MRC Technical Support.Table 4-3: Primary Error Codes (Continued)Error Code Meaning Suggested Operator Action Suggested Technical Staff Action
Troubleshooting 4-6STRATA TX Operator’s Guide/Tech Ref ManualE035 TXU 75 Ohm Coax Current Error Note - these errors can only appear in a TX System with TXU and a TCU, when powering the TXU from the TCU or from the TCU to the TXU via DC power superimposed on the coax cable between the TCU and the TXU.• Check connection of coax cable between TCU and TXU. Verify connectors are fully mated and verify cable and connectors are undamaged.• Make sure all power cables are connected properly.• Contact technical staff. If errors persist with correct coax connections and correct power connected, unit has suffered internal failure. Call MRC Technical Support.E036 TXU 75 Ohm Coax Voltage errorE037 TXU 75 Ohm Coax Power ErrorE038 TXU 50 Ohm Coax Current ErrorE039 TXU 50 Ohm Coax Voltage errorE03A TXU 50 Ohm Coax Power ErrorE03B TXU Circular Connector Current Error• Verify all power cables are properly connected and are not damaged.• Verify correct DC input power is being applied to the TXU.• Contact technical staff.If errors persist with correct power connected, unit has suffered internal failure. Call MRC Technical Support.E03C TXU Circular Connector Voltage ErrorE03D TXU Circular Connector Power ErrorE03E TXU DC Bus Error • Contact technical staff. Call MRC Technical Support.E040 TCU 2.048 Volt Reference Error • Check for error codes related to power - E043 thru E048. Correct power problem• Contact technical staff.If errors persist with correct power connected, unit has suffered internal failure. Call MRC Technical Support.E041 TCU 5.5 Volt Reference ErrorTable 4-3: Primary Error Codes (Continued)Error Code Meaning Suggested Operator Action Suggested Technical Staff Action
Troubleshooting 4-7STRATA TX Operator’s Guide/Tech Ref ManualE042 TCU Temperature error • Check TCU to be sure it is not too close to sources of heat. Relocate TCU, if possible.• Verify TCU has room around it for air circulation. Move objects preventing air flow. • Contact technical staff.If errors persist with proper location and airflow and correct power is connected, unit has suffered internal failure. Call MRC Technical Support.E043 TCU 75 Ohm Coax Current Error Note - these errors can only appear in a TX System with TXU and a TCU, when powering the TXU from the TCU or from the TCU to the TXU via DC power superimposed on the coax cable between the TCU and the TXU.• Check connection of coax cable between TCU and TXU. Verify connectors are fully mated and verify cable and connectors are undamaged.• Make sure all power cables are connected properly.• Contact technical staff. If errors persist with correct coax connections and correct power connected, unit has suffered internal failure. Call MRC Technical Support.E044 TCU 75 Ohm Coax Voltage ErrorE045 TCU 75 Ohm Coax Power ErrorE046 TCU Circular Connector Current Error• Make sure all power cables are connected properly and are not damaged.• Verify correct DC input power is being applied to the TCU.• Contact technical staff.If errors persist with correct power connected, unit has suffered internal failure. Call MRC Technical Support.E047 TCU Circular Connector Voltage ErrorE048 TCU Circular Connector Power ErrorE049 TCU DC Bus Error Contact technical staff. Call MRC Technical Support.Table 4-3: Primary Error Codes (Continued)Error Code Meaning Suggested Operator Action Suggested Technical Staff Action
Troubleshooting 4-8STRATA TX Operator’s Guide/Tech Ref Manual4.4.2 Error Status The significance of the Error Status digit depends on what Primary Error Code is being reported. See Table 4-4.4.4.3 Unit ID The Unit ID digit identifies which part of the STRATA TX System is reporting a problem. See Table 4-5.Table 4-4: Error Status DigitStatus Digit MeaningStatus Error (Error Codes E0E0 thru E0E4, E020, E021, and E080)8 There is an error.Parameter Error (Error Codes E030 thru E039, E03A thru E03E, and E042 thru E049, E060 thru E069, and E06A)4 Value is too low.8 Value is too high.Table 4-5: STRATA Unit ID DigitUnit ID1 Transmitter Unit (TXU)2 Transmitter Control Unit (TCU)3 High Power Unit (HPU)4.5 Operational ProblemsInformation provided on the following pages will assist you in troubleshooting problems that arise in the operation of your STRATA TX System.For video problems, See Table 4-6 on page 4-9; for general system problems, See Table 4-7 on page 4-10.
Troubleshooting 4-9STRATA TX Operator’s Guide/Tech Ref ManualTable 4-6: Video Problems Problem Possible Cause Suggested Operator Action Suggested Technical Staff ActionVideo ProblemsNo video. Problem with video source or cabling• Check video source and cabling.• Contact technical staff.• Check video source and cabling.• Call MRC Technical Support.Transmitter and Receiver compatability problems• Verify Transmitter and Receiver are both operating in the same digital or analog modes.• Verify Transmitter and Receiver are both operating on the same frequency. If frequency offsets are used, verify offsets are identical between Transmitter and Receiver.• Contact technical staff.• Call MRC Technical SupportVideo source configuration problem• Verify TXU/TCU front panel settings match video source inputs.• Contact technical staff.• Verify video inputs match STRATA TX Configurator settings.• Call MRC Technical Support.
Troubleshooting 4-10STRATA TX Operator’s Guide/Tech Ref ManualTable 4-7: General System Problems Problem Possible Cause Suggested Operator Action Suggested Technical Staff ActionGeneral System ProblemsStatus LED on TXU/ TCU is yellow.TX System is indicating a Minor Alarm.• Check all Monitor Screens on TXU/TCU display. Troubleshoot per Section 4.3 on page 4-1.• Check Error Code Screen on TXU/TCU display. Troubleshoot per Section 4.4 on page 4-3.• Error messages: Troubleshoot per Section 4.3 on page 4-1.• Error Codes: Troubleshoot per Section 4.4 on page 4-3.Status LED on TXU or TCU is red.TX is indicating a Major Alarm.TURN OFF POWER and call for service.Call MRC Technical Support.Changing settings on one unit doesn’t change settings on the other in a connected TXU and TCU system. TXU and TCU are not communicating.• Check connection between TXU and TCU.• Turn power off in both TXU and TCU. Then turn power on in both TXU and TCU.If problem persists with correct coax connections, one or both units have suffered internal failure. Call MRC Technical Support.
A Channels & Frequencies A-1STRATA TX Operator’s Guide/Tech Ref ManualChannels & Frequencies A.1 Appendix OverviewThis Appendix presents the channels and frequencies that can be programmed into your STRATA TX System at the factory.Here are the topics covered:Topic PageInitial Factory Presets A-13.4 to 3.8 GHz Channel Plan A-14.4 to 5.0 GHz Channel Plan A-26.4 to 7.1 GHz Channel Plan A-26.9 to 7.5 GHz Channel Plan A-37.4 to 8.0 GHz Channel Plan A-37.8 to 8.5 GHz Channel Plan A-48.2 to 8.9 GHz Channel Plan A-410.0 to 10.7 GHz Channel Plan A-510.5 to 11.2 GHz Channel Plan A-510.8 to 11.5 GHz Channel Plan A-612.7 to 13.25 GHz Channel Plan A-6A.2 Initial Factory PresetsThis section lists the channels and frequencies for each RF band covered by the STRATA TX System. These frequencies are preset at the factory, but can be modified using the STRATA TX Configurator software.Note These frequency settings should only be changed by qualified technical personnel.A.2.1 3.4 to 3.8 GHz Channel PlanThe channel plan for the 3.4 to 3.8 GHz STRATA TX System is contained in Tab l e A - 1.Table A-1: 3.4 to 3.8 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 3406.250 3418.250 3431.2502 3443.250 3455.250 3467.2503 3480.250 3492.250 3504.2504 3506.250 3518.750 3531.2505 3543.750 3556.250 3568.7506 3581.250 3593.750 3606.2507 3610.000 3620.000 3630.0008 3640.000 3650.000 3660.0009 3670.000 3680.000 3690.00010 3700.000 3710.000 3720.00011 3730.000 3740.000 3750.000
Channels & Frequencies A-2STRATA TX Operator’s Guide/Tech Ref ManualA.2.2 4.4 to 5.0 GHz Channel PlanThe channel plan for the 4.4 to 5.0 GHz STRATA TX System is contained in Tab l e A- 2.12 3760.000 3770.000 3780.00013 3790.000 3800.000 3800.00014 3800.000 3800.000 3800.000Table A-2: 4.4 to 5.0 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 4450.000 4475.000 4500.0002 4525.000 4550.000 4575.0003 4600.000 4625.000 4650.0004 4675.000 4700.000 4725.0005 4750.000 4775.000 4800.0006 4825.000 4850.000 4875.0007 4900.000 4925.000 4925.0008 4940.500 4941.500 4942.5009 4943.500 4944.500 4944.50010 4947.500 4952.000 4957.50011 4962.500 4967.500 4972.50012 4977.500 4982.500 4982.50013 4985.500 4986.500 4987.50014 4988.500 4989.500 4989.500Table A-1: 3.4 to 3.8 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)A.2.3 6.4 to 7.1 GHz Channel PlanThe channel plan for the 6.4 to 7.1 GHz STRATA TX System is contained in Tab l e A - 3.Table A-3: 6.4 to 7.1 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 6881.250 6887.500 6893.7502 6906.250 6912.500 6918.7503 6913.250 6937.500 6943.7504 6956.250 6962.500 6968.7505 6981.250 6987.500 6993.7506 7006.250 7012.500 7018.7507 7031.250 7037.500 7043.7508 7056.250 7062.500 7068.7509 7081.250 7087.500 7093.75010 7106.250 7112.500 7118.75011 6421.250 6437.500 6443.75012 6456.250 6462.500 6468.75013 6481.250 6487.500 6493.75014 65.6.250 6512.500 6518.750
Channels & Frequencies A-3STRATA TX Operator’s Guide/Tech Ref ManualA.2.4 6.9 to 7.5 GHz Channel PlanThe channel plan for the 6.9 to 7.5 GHz STRATA TX System is contained in Tab l e A- 4.Table A-4: 6.9 to 7.5 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 6900.000 6915.000 6930.2502 6945.250 6960.000 6975.7503 6990.250 7005.000 7020.7504 7035.250 7050.000 7065.7505 7080.250 7095.000 7110.7506 7125.250 7140.000 7155.7507 7170.250 7185.000 7200.7508 7215.250 7230.000 7245.7509 7260.250 7275.000 7290.75010 7305.250 7320.000 7335.75011 7350.250 7365.000 7380.75012 7395.250 7410.000 7425.75013 7440.250 7455.000 7470.75014 7485.250 7500.000 7500.000A.2.5 7.4 to 8.0 GHz Channel PlanThe channel plan for the 7.4 to 8.0 GHz STRATA TX System is contained in Tab l e A - 5.Table A-5: 7.4 to 8.0 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 7405.000 7425.000 7445.0002 7455.000 7475.000 7495.0003 7505.000 7525.000 7545.0004 7555.000 7575.000 7595.0005 7605.000 7625.000 7645.0006 7655.000 7675.000 7695.0007 7705.000 7725.000 7745.0008 7755.000 7775.000 7795.0009 7805.000 7825.000 7845.00010 7855.000 7875.000 7895.00011 7905.000 7925.000 7945.00012 7955.000 7975.000 7995.00013 8005.000 8025.000 8045.00014 8055.000 8075.000 7085.000
Channels & Frequencies A-4STRATA TX Operator’s Guide/Tech Ref ManualA.2.6 7.8 to 8.5 GHz Channel PlanThe channel plan for the 7.8 to 8.5 GHz STRATA TX System is contained in Tab l e A- 6.Table A-6: 7.8 to 8.5 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 7805.000 7825.000 7845.0002 7855.000 7875.000 7895.0003 7905.000 7925.000 7945.0004 7955.000 7975.000 7995.0005 8005.000 8025.000 8045.0006 8055.000 8075.000 8095.0007 8105.000 8125.000 8145.0008 8155.000 8175.000 8195.0009 8205.000 8225.000 8245.00010 8255.000 8275.000 8295.00011 8305.000 8325.000 8345.00012 8355.000 8375.000 8395.00013 8405.000 8425.000 8445.00014 8455.000 8475.000 8495.000A.2.7 8.2 to 8.9 GHz Channel PlanThe channel plan for the 8.2 to 8.9 GHz STRATA TX System is contained in Tab l e A - 7.Table A-7: 8.2 to 8.9 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 8205.000 8225.000 8245.0002 8255.000 8275.000 8295.0003 8305.000 8325.000 8345.0004 8355.000 8375.000 8395.0005 8405.000 8425.000 8445.0006 8455.000 8475.000 8495.0007 8505.000 8525.000 8545.0008 8555.000 8575.000 8595.0009 8605.000 8625.000 8645.00010 8655.000 8675.000 8695.00011 8705.000 8725.000 8745.00012 8755.000 8775.000 8795.00013 8805.000 8825.000 8845.00014 8855.000 8875.000 8895.000
Channels & Frequencies A-5STRATA TX Operator’s Guide/Tech Ref ManualA.2.8 10.0 to 10.7 GHz Channel PlanThe channel plan for the 10.0 to 10.7 GHz STRATA TX System is contained in Table A- 8 .Table A-8: 10.0 to 10.7 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 10005.000 10025.000 10045.0002 10055.000 10075.000 10095.0003 10105.000 10125.000 10145.0004 10155.000 10175.000 10195.0005 10205.000 10225.000 10245.0006 10255.000 10275.000 10295.0007 10305.000 10325.000 10345.0008 10355.000 10375.000 10395.0009 10405.000 10425.000 10445.00010 10455.000 10475.000 10495.00011 10505.000 10525.000 10545.00012 10555.000 10575.000 10595.00013 10605.000 10625.000 10645.00014 10655.000 10675.000 10695.000A.2.9 10.5 to 11.2 GHz Channel PlanThe channel plan for the 10.4 to 11.2 GHz STRATA TX System is contained in Tab l e A - 9.Table A-9: 10.5 to 11.2 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 10505.000 10525.000 10545.0002 10555.000 10575.000 10595.0003 10605.000 10625.000 10645.0004 10655.000 10675.000 10695.0005 10705.000 10725.000 10745.0006 10755.000 10775.000 10795.0007 10805.000 10825.000 10845.0008 10855.000 10875.000 10895.0009 10905.000 10925.000 10945.00010 10955.000 10975.000 10995.00011 11005.000 11025.000 11045.00012 11055.000 11075.000 11095.00013 11105.000 11125.000 11145.00014 11155.000 11175.000 11195.000
Channels & Frequencies A-6STRATA TX Operator’s Guide/Tech Ref ManualA.2.10 10.8 to 11.5 GHz Channel PlanThe channel plan for the 10.8 to 11.5 GHz STRATA TX System is contained in Table A-10.A.2.11 12.7 to 13.25 GHz Channel PlanThe channel plan for the 12.7 to 13.25 GHz STRATA TX System is contained in Table A- 11.Table A-10: 10.8 to 11.5 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 10805.000 10825.000 10845.0002 10855.000 10875.000 10895.0003 10905.000 10925.000 10945.0004 10955.000 10975.000 10995.0005 11005.000 11025.000 11045.0006 11055.000 11075.000 11095.0007 11105.000 11125.000 11145.0008 11155.000 11175.000 11195.0009 11205.000 11225.000 11245.00010 11255.000 11275.000 11295.00011 11305.000 11325.000 11345.00012 11355.000 11375.000 11395.00013 11405.000 11425.000 11445.00014 11455.000 11475.000 11495.000Table A-11: 12.7 to 13.25 GHz Channel PlanChannel (-) Offset (MHz)(0) Center (MHz)(+) Offset (MHz)1 12706.250 12712.500 12718.7502 12731.250 12737.500 12743.7503 12756.250 12762.500 12768.7504 12781.250 12787.500 12793.7505 12806.250 12812.500 12818.7506 12831.250 12837.500 12843.7507 12856.250 12862.500 12868.7508 12881.250 12887.500 12893.7509 12906.250 12912.500 12918.75010 12931.250 12937.500 12943.75011 12956.250 12962.500 12968.75012 12981.250 12987.500 12993.75013 13006.250 13012.500 13018.75014 13031.250 03037.500 03043.75015 13056.250 13062.500 13068.75016 13081.250 13087.500 13093.75017 13106.250 13112.500 13118.75018 13131.250 13137.500 13143.75019 13156.250 13162.500 13168.75020 13181.250 13187.500 13193.75021 13206.250 13212.500 13218.75022 13231.250 13237.500 13243.750
B Glossary B-1STRATA TX Operator’s Guide/Tech Ref ManualGlossaryThis section describes acronyms and abbreviations used in communications, broadcasting, and in our products and documentation. Table B-1: Useful Terms Term Explanation16 QAM 16-state Quadrature Amplitude ModulationThe signal (video + audio) is imposed onto the 70 MHz carrier by varying both the phase and the amplitude of the signal while keeping the frequency constant. There are 16 possible combinations of phase and amplitude that can be used to carry information.4FSK 4-state Frequency Shift Keying8 PSK 8-Phase Shift Keying8 QAM 8-state Quadrature Amplitude Modulation The signal (video + audio) is imposed onto the 70 MHz carrier by varying both the phase and the amplitude of the signal while keeping the frequency constant. There are 8 possible combinations of phase and amplitude that can be used to carry information.64 QAM 64-state Quadrature Amplitude ModulationThe signal (video+audio) is imposed onto the 70 MHz carrier by varying both the phase and the amplitude of the signal while keeping the frequency constant. There are 64 possible combinations of phase and amplitude that can be used to carry information.A & C Alarm and ControlACU AC to DC Converter UnitADPCM Adaptive Differential Pulse Code ModulationAES Audio Engineering Society AES/EBU Unofficial name for a digital audio standard developed as a joint enterprise of the AES and the EBU. AFC Automatic Frequency ControlAGC Automatic Gain ControlAIS Alarm Indication Signal (all one’s)AMI Alternate Mark Inversion, line code format for traffic data.AVG AverageASI Asynchronous Serial InterfaceA serial communications interface operating at 270 Mbit/sec., generally used in field news-gathering operations. Baseband A composite signal in which video and audio signals are combined together, with video occupying approximately 0-4.5 MHz and audio modulated onto subcarriers in the 5-6 MHz range. Also called Composite.BB BasebandTable B-1: Useful Terms (Continued)
Glossary B-2STRATA TX Operator’s Guide/Tech Ref ManualBDC Block Down ConverterBER Bit Error RatioThe ratio of bits containing errors to the total number of bits in the signal, over a time period.BiasT A type of interconnection between the IDU and the ODU. In Bias T wiring, IF and DC are combined and carried on the coax cable up the ODU; blocking circuitry prevents the DC from entering the IDU.BISS Basic Interoperable Scrambling System A means of encrypting and decrypting a digital signal to prevent unauthorized reception. The encryption and decryption are controlled by a digital key, which is shared at both the transmitting and receiving location. BISS-1 BISS encryption that uses a fixed key.BISS-E BISS encryption that uses an encrypted key.BNC Bayonet lock coaxial connectorBPF Band Pass Filterbps or b/sec Bits per secondBPSK Binary Phase Shift KeyingBW BandwidthCCITT International Telegraph and Telephone Consultative Committee A telecommunications standardizing committee of the ITU.CCPS Command & Control Power SupplyCENELEC European Committee for Electrotechnical StandardizationTable B-1: Useful Terms (Continued)CNR Carrier-to-Noise RatioCOFDM Coded Orthogonal Frequency Division MultiplexingComposite (Baseband)A band or grouping of frequencies and/or subcarriers, including video, occupied by the signal in a radio transmission system. Also called Baseband.CV Composite VideoVideo signal in which the chrominance (color) and luminance (brightness) information are combined in one signal. S-Video separates the chrominance and luminance into individual signals.CSI Channel-State InformationCW Carrier WaveDAB Digital Audio BroadcastingdB Decibel A logarithmic measurement of power or voltage, applied to audio and RF signals. dBm A unit of measurement referenced to one milliwatt.DCE Data Communications Equipment A device that communicates with a DTE device. In practical terms, the DCE is usually a modem and the DTE device is usually a computer.De-emphasisReducing the amplitude of high frequency components of an analog audio signal. Done on the receive end of an analog link to take out Emphasis added on the transmit side.DFT Discrete Fourier TransformDMUX, DEMUXDemultiplexerTable B-1: Useful Terms (Continued)
Glossary B-3STRATA TX Operator’s Guide/Tech Ref ManualDQPSK Differential Quadrature (Quaternary) Phase-Shift KeyingDRL Data Return LinkDTE Data Terminal Equipment A device that communicates with a DCE device. In practical terms, the DTE is usually a computer and the DCE device is usually a modem.Duplex A channel capable of transmitting information simultaneously in both directions.DVB Digital Video BroadcastingDVB-ASI Digital Video Broadcasting - Asynchronous Serial InterfaceA widely-used MPEG-2 digital transport interface. Physically the connection is made either with optical fiber or 75 ohm coax with a BNC connector. Interface can support data rates up to 270 Mb/sec.DVB-C Digital Video Broadcasting - CableDVB-S Digital Video Broadcasting - SatelliteDVB-T Digital Video Broadcasting - TerrestrialE1 2.048 Mbps data rate.EIA Electronic Industries AssociationAn industry association that establishes various standards.EBU European Broadcasting UnionIn addition to other activities, EBU produces technical statements and recommendations for PAL television systems. Table B-1: Useful Terms (Continued)EMC Electromagnetic compatibility.Emphasis Boosting the amplitude of high frequency components of an analog audio signal. Done on the transmit side of an analog link to improve signal-to-noise ratio.ERRS ErrorsESD Electrostatic DischargeETSI European Telecommunications Standards InstituteFCC Federal Communications CommissionThe United State's communications regulatory agency.FDM Frequency Division MultiplexingFEC Forward Error CorrectionsFFT Fast Fourier TransformFIFO First In, First Out bufferFIR Finite Impulse ResponseFMT FM Video Modulator or FM TransmitterFPGA Field Programmable Gate ArrayFSK Frequency-Shift KeyingGHz Gigahertz (109 cycles per second)GI Guard IntervalGND GroundGUI Graphic User InterfaceH/W or HW HardwareHPF High Pass FilterHPU High Power UnitICI Inter-Carrier InterferenceTable B-1: Useful Terms (Continued)
Glossary B-4STRATA TX Operator’s Guide/Tech Ref ManualID IdentificationIDU Indoor UnitIF Intermediate FrequencyIMD Inter-Modulation DistortionIRD Integrated Receiver DecoderIRE 1. Institute of Radio Engineers, an international professional radio engineering association that establishes various standards.2. A unit of measurement, established by the IRE, in which 1 IRE Unit =.00714 volts peak-to-peak (Vp-p) and 140 IRE units equals 1 Vp-p.ISI Inter-Symbol InterferenceISO International Standards Organizationkbps Kilobits per secondkHz Kilo (1,000) cycles per secondLAN Local Area NetworkLCD Liquid Crystal DisplayLcl LocalLED Light Emitting DiodeLNA Low Noise AmplifierLNB Low Noise Block Down ConverterLNC Low Noise ConverterLO Local OscillatorLOS Loss of SignalLPF Low Pass FilterLQ Link QualityMbps Megabits per secondMHz Million (1,000,000) cycles per secondTable B-1: Useful Terms (Continued)MPEG Moving Picture Experts GroupMRC Microwave Radio CommunicationsMultipath An unpredictable set of reflections and/or direct waves, each with its own degree of attenuation and delay. Due to obstacles and reflectors in the wireless channel, transmitted signals arrive at the received from various directions over multiple paths.MUX MultiplexerN/C No ConnectionNICAM Near-Instantaneous Companding and MultiplexingNRZ Non-Return-to-Zero (Modulation)NTSC National Television System CommitteeColor television standard used in the US. Provides 525 horizontal lines of resolution. Not compatible with PAL or SECAM.Null modem cableAn RS-232 cable designed to connect two computers (or other data sources) together. It has male DB9 connectors on each end, to mate with the DB9 female connectors on the PCs. It also has the Transmit and Receive connections crossed over so Transmit (pin 3) on one end connects to Receive (pin 2) on the other.Also called “Crossover Cable”.ODU Outdoor UnitOFDM Orthogonal Frequency Division MultiplexingOOK On-Off KeyingTable B-1: Useful Terms (Continued)
Glossary B-5STRATA TX Operator’s Guide/Tech Ref ManualPAL Phase Alteration LineColor television standard used in many European countries. Provides 625 horizontal lines of resolution. Not compatible with NTSC or SECAM.PC Personal ComputerPCR Program Clock ReferencePER Parity Error RateØLK Phase LockPID Program IdentificationPLL Phase Lock LoopQAM Quadrature Amplitude ModulationQPSK Quadrature Phase Shift KeyingThe signal (video+audio) is imposed onto the 70 MHz carrier by varying the phase of the signal while keeping the amplitude and frequency constant. There are 4 possible values of phase that can be used to carry information.RCL Received Carrier LevelThe strength of a received RF signal, in dBm.RCU Receiver Control UnitRcvr ReceiverRD Receive DataRDS Radio Data SystemRF Radio FrequencyRF Level RF Power from the transmitter.RFU Radio Frequency UnitRMA Return Material AuthorizationTable B-1: Useful Terms (Continued)R-S Reed-SolomonRX ReceiverRXU Receiver UnitRZ Return to ZeroSC Service ChannelSC Single CarrierSDI Synchronous Digital InterfaceA serial communications interface operating at 270 Mbit/sec. Generally used for in-studio news operations. SD EMB Synchronous Digital Interface EmbeddedSECAM Sequence de Couleur Avec MemoireColor television standard used in France, Russia, and other countries. Provides 625 horizontal lines of resolution. Not compatible with NTSC or PAL. Not supported by this product.SER Symbol Error RateSetpt Set pointSFN Single-Frequency NetworkSG Signal GroundSI Service InformationSimplex A channel capable of transmitting information in only one direction.Site ID A physical location where any number of modems, transmitters, or receivers are installed.SMPTE Society of Motion Picture and Television EngineersSNR Signal-to-Noise RatioSR16 Symbol Rate 16Table B-1: Useful Terms (Continued)
Glossary B-6STRATA TX Operator’s Guide/Tech Ref ManualSTDBY StandbySubcarrier An electromagnetic signal that is used as a medium for placing an information channel above another information channel.S-Video Video signal in which the chrominance (color) and luminance (brightness) information are separated into individual subcarrier signals. Also called Y/C Video. Composite Video combines them into one signal.SYNTH SynthesizerS/W or SW SoftwareT1 1.544 Mbps data rateTC Transmitter ControlTCU Transmitter Control UnitTD Transmit DataTX TransmitterTXU Transmitter UnitVCO Voltage Controlled OscillatorVCXO Voltage Controlled Crystal OscillatorVDC Volts Direct CurrentVF Voice FrequencyVideo A term pertaining to the bandwidth and spectrum of the signal that results from television scanning and which is used to reproduce a picture.WAN Wide Area NetworkXMIT TransmitXmtr TransmitterTable B-1: Useful Terms (Continued)Y/C Video signal in which the chrominance (color) and luminance (brightness) information are separated into individual subcarrier signals. Also called S-Video. Composite Video combines them into one signal.Table B-1: Useful Terms (Continued)
Index Index-1STRATA TX Operator’s GuideNumerics10.0 to 10.7 GHz Channel Plan . . . . . . . . . . . . . . . . . A-510.5 to 11.2 GHz Channel Plan . . . . . . . . . . . . . . . . . A-510.8 to 11.5 GHz Channel Plan . . . . . . . . . . . . . . . . . A-612.7 to 13.25 GHz Channel Plan . . . . . . . . . . . . . . . . A-616 QAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13.4 to 3.8 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-14.4 to 5.0 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-24FSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-16.4 to 7.1 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-26.9 to 7.5 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-364 QAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-17.4 to 8.0 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-37.8 to 8.5 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-475 Ohm Coax option . . . . . . . . . . . . . . . . . . . . . . . . . .3-38 PSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-18 QAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-18.2 to 8.9 GHz Channel Plan . . . . . . . . . . . . . . . . . . . A-4AAbout This Manual . . . . . . . . . . . . . . . . . . . . . . Notices-iAccessing the Control Screen . . . . . . . . . . . . . . . . . .3-19Accessing the Main Screen . . . . . . . . . . . . . . . . . . . .3-19Accessing the Monitor Screen . . . . . . . . . . . . . . . . . .3-19ACUAC INPUT connector . . . . . . . . . . . . . . . . . . . .3-9Controls, Indicators, and Connectors . . . . . . . .3-8DC OUTPUT connector . . . . . . . . . . . . . . . . . .3-9fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9POWER Switch . . . . . . . . . . . . . . . . . . . . . . . . 3-9ADPCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1AES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1AES/EBU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1AFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1airborne operations . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Aircraft Remote Control Panel . . . . . . . . . . . . . . . . . . 2-9ASI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Audience, Intended . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2AUDIO connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9AUDIO connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3BBaseband . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1BER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2BiasT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2BISS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2BISS 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2BISS E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2BISS-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2BNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2CCCPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2CENELEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Channel, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30Channels & Frequencies . . . . . . . . . . . . . . . . . . . . . . A-1Channels and Frequencies . . . . . . . . . . . . . . . . . . . . A-1Initial Factory Presets . . . . . . . . . . . . . . . . . . . A-1COFDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Composite (Baseband) . . . . . . . . . . . . . . . . . . . . . . . B-2Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Configuration Differences . . . . . . . . . . . . . . . . . . . . . . 2-9
Index-2STRATA TX Operator’s GuideControlChanging a Preset . . . . . . . . . . . . . . . . . . . . .3-29TXU and/or TCU Control Operations . . . . . . .3-27Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notices-iDdB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2dBm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2DC ON COAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3DC ON COAX override switch . . . . . . . . . . . . . . . . . .2-10DC ON COAX switch . . . . . . . . . . . . . . . . . . . . . . . . . .3-3DC power requirements . . . . . . . . . . . . . . . . . . . . . . .2-5Deemphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Default to Main Screen . . . . . . . . . . . . . . . . . . . . . . .3-20Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1DocumentsRelated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2DTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3DVB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3DVB-ASI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3DVB-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3DVB-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3DVB-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3EEBU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Ffactory default settings . . . . . . . . . . . . . . . . . . . . . . . .2-6FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3FMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Frequently Performed TasksChanging a Preset . . . . . . . . . . . . . . . . . . . . . 3-29Controlling TCU to TXU DC on Coax . . . . . . 3-32Powering the STRATA TX System . . . . . . . . 3-12Preparing for OperationMobile Installation . . . . . . . . . . . . . . . . . . 3-10Mounting to the Tripod . . . . . . . . . . . . . . . 3-11Portable Deployment . . . . . . . . . . . . . . . . 3-10Selecting a Channel . . . . . . . . . . . . . . . . . . . 3-30Setting Monitor Output . . . . . . . . . . . . . . . . . . 3-31Front Panel vs. STRATA TX Configurator Settings . 3-34FSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3GGeneral System Problems . . . . . . . . . . . . . . . . . . . . 4-10GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3GI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3HHPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3IID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4IRD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4ISO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4LLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4MMessages, Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Index-3STRATA TX Operator’s GuideMHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Mobile Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5Monitor Output, Selecting . . . . . . . . . . . . . . . . . . . . .3-31MonitoringAnalog - IF mode . . . . . . . . . . . . . . . . . . . . . .3-20Analog IF Output . . . . . . . . . . . . . . . . . . . . . . .3-20COFDM - IF mode . . . . . . . . . . . . . . . . . . . . .3-20COFDM ASI In mode . . . . . . . . . . . . . . . . . . .3-20COFDM Only - ASI In . . . . . . . . . . . . . . . . . . .3-20DVB-S (Satellite) . . . . . . . . . . . . . . . . . . . . . . .3-20DVB-S mode . . . . . . . . . . . . . . . . . . . . . . . . . .3-20MPEG Only ASI Out . . . . . . . . . . . . . . . . . . . .3-20MPEG/COFDM IF Out . . . . . . . . . . . . . . . . . .3-20Using the Monitor Screens in Analog - IF Mode 3-25Using the Monitor Screens in COFDM - IF Mode 3-23Using the Monitor Screens in COFDM ASI In Mode 3-24Using the Monitor Screens in DVB-S Mode . .3-26Using the Monitor Screens in Ext IF Input Mode 3-22MPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4MRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4MRC Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11Dovetail Adapter Plates . . . . . . . . . . . . 3-10, 3-11Fixed Mounting Bracket . . . . . . . . . . . . . . . . .3-10Mounting Plate . . . . . . . . . . . . . . . . . . . . . . . .3-10Quick Release . . . . . . . . . . . . . . . . . . . . . . . . .3-10Universal Mounting Bracket . . . . . . . . . . . . . .3-10Multipath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Multi-Unit Systems . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3NN/C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4NOT ON CHANNEL message . . . . . . . . . . . . . . . . . . .4-2Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notices-iNTSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Null modem cable . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4OOFDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4On-Line Viewing . . . . . . . . . . . . . . . . . . . . . . . . .Notices-iiOOK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Operational Problems . . . . . . . . . . . . . . . . . . . . . . . . 4-8General System . . . . . . . . . . . . . . . . . . . . . . . 4-10Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9Ordering Documentation . . . . . . . . . . . . . . . . . . . . . . 1-2Output, Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31Overview of Controls, Indicators, and Connectors . . . 3-2PPAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5PID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5Portable Deployment . . . . . . . . . . . . . . . . . . . . . . . . . 2-5portable operations . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Power OptionsTXU and TCU - separate locations . . . . . . . . . 2-4TXU and TCU co-located . . . . . . . . . . . . . . . . 2-4Powering the STRATA SystemSuperimposing DC Power . . . . . . . . . . . . . . . 3-12Superimposing DC Power with Manual Control 3-12Powering the STRATA TX SystemSingle TCU Power Up and Power Down . . . . 3-13Single TXU Power up and Power Down . . . . 3-14Superimposing DC Power . . . . . . . . . . . . . . . 3-12TXU and TCU Power Up and Power Down - Co-Located 3-15TXU and TCU Power Up and Power Down - Separate Locations . . . . . . . . . . . . . . . . . . . . . . . . . 3-17Preparing for Operation . . . . . . . . . . . . . . . . . . . . . . 3-10Preset, Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Index-4STRATA TX Operator’s GuideProprietary Material . . . . . . . . . . . . . . . . . . . . . . Notices-iQQAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5QPSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5Quality Certification . . . . . . . . . . . . . . . . . . . . . . Notices-iRRCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5RCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5Regulatory Status . . . . . . . . . . . . . . . . . . . . . . . Notices-iRemote Control Options . . . . . . . . . . . . . . . . . . . . . . .2-3Remote Control Panel . . . . . . . . . . . . . . . . . . . . . . . . .2-9RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5RMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5RX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5RXU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5SScreens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . .3-19SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5SECAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5Single Unit Systems . . . . . . . . . . . . . . . . . . . . . . . . . .2-3SMPTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5SR16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5STRATA ACU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8STRATA Aircraft Remote Control PanelControls, Indicators, and Connectors . . . . . . . .3-9controls, indicators, and connectors . . . . . . . . .3-9STRATA Remote Control PanelControls, Indicators, and Connectors . . . . . . . .3-9STRATA Remote Control Panels . . . . . . . . . . . . . . . .2-8STRATA TX Configuratorsettings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1STRATA TX Configurator software . . . . . . . . . . . . . . 2-5STRATA TX Systemcomponents . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2controls, indicators, and connectors . . . . . . . . 3-2key features . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1STRATA TX System componentsACU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3HPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Remote Control Panels . . . . . . . . . . . . . . . . . . 2-3TCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3TXU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Subcarrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6superimposed DC power . . . . . . . . . . . . . . . . . . . . . . 2-5S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6SYNTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6SystemCommunications . . . . . . . . . . . . . . . . . . . . . . . 2-5Components . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Configurations, Typical . . . . . . . . . . . . . . . . . 2-12Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5OptionsAntenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Deployment . . . . . . . . . . . . . . . . . . . . . . . . 2-5Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5System ComponentsSTRATA ACU . . . . . . . . . . . . . . . . . . . . . . . . . 2-7STRATA Remote Control Panels . . . . . . . . . . 2-7STRATA TCU . . . . . . . . . . . . . . . . . . . . . . . . . 2-7STRATA TXU . . . . . . . . . . . . . . . . . . . . . . . . . 2-7System Description . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Index-5STRATA TX Operator’s GuideSystem Problems . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10TTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6TCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-675 Ohm Coax option . . . . . . . . . . . . . . . . . . . . .3-7Alphanumeric Display . . . . . . . . . . . . . . . . . . . .3-5alphanumeric display . . . . . . . . . . . . . . . . . . . .3-5AUDIO Connector . . . . . . . . . . . . . . . . . . . . . . .3-8AUDIO connector . . . . . . . . . . . . . . . . . . . . . . .3-8Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . .3-7Controls, Indicators, and Connectors . . . . . . . .3-5DC ON COAX . . . . . . . . . . . . . . . . . . . . . . . . . .3-7DC ON COAX override switch . . . . . . . . . . . .2-11DC ON COAX Switch . . . . . . . . . . . . . . . . . . . .3-6DC ON COAX switch . . . . . . . . . . . . . . . . . . . .3-7FMT module . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8Monitor (MON) Connector . . . . . . . . . . . . . . . . .3-8MPEG/COFDM . . . . . . . . . . . . . . . . . . . . . . . . .2-8POWER connector . . . . . . . . . . . . . . . . . . . . . .3-8PWR Switch . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6RS-232 Connector . . . . . . . . . . . . . . . . . . . . . .3-8RS-232 connector . . . . . . . . . . . . . . . . . . . . . . .3-8SIGNAL IN Connector . . . . . . . . . . . . . . . . . . . .3-8SIGNAL IN connector . . . . . . . . . . . . . . . . . . . .3-8SIGNAL OUT Connector . . . . . . . . . . . . . . . . . .3-8SIGNAL OUT connector . . . . . . . . . . . . . . . . . .3-8Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6XMIT LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6TCU - New Configuration . . . . . . . . . . . . . . . . . . . . .2-11TCU - Older Configuration . . . . . . . . . . . . . . . . . . . . .2-11TCU configuration . . . . . . . . . . . . . . . . . . . . . . . . 2-7, 2-8TCU to TXU DC on Coax, Controlling . . . . . . . . . . . .3-32Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3Error Messages . . . . . . . . . . . . . . . . . . . . . . . . 4-1Error Status . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8general system problems . . . . . . . . . . . . . . . . 4-8Messages on Display . . . . . . . . . . . . . . . . . . . 4-1Operational Problems . . . . . . . . . . . . . . . . . . . 4-8Primary Error Code . . . . . . . . . . . . . . . . . . 4-3, 4-8Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Unit ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8video problems . . . . . . . . . . . . . . . . . . . . . . . . 4-8TX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6PWR Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4TXU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-670 MHz COFDM . . . . . . . . . . . . . . . . . . . . . . . 2-7Alphanumeric Display . . . . . . . . . . . . . . . . . . . 3-3AUDIO Connector . . . . . . . . . . . . . . . . . . . . . . 3-3AUDIO connector . . . . . . . . . . . . . . . . . . . . . . 2-9Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Controls, Indicators, and Connectors . . . . . . . 3-2Controls, indicators, and connectors . . . . . . . . 3-2FMT IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7FMT module . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7Front Panel DC ON COAX Switch . . . . . . . . . . 3-2INPUT Connector . . . . . . . . . . . . . . . . . . . . . . 3-3MPEG/CODFM module . . . . . . . . . . . . . . . . . . 2-7POWER IN Connector . . . . . . . . . . . . . . . . . . . 3-4PWR Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Rear Panel DC ON COAX Switch . . . . . . . . . . 3-5RF Output Connector . . . . . . . . . . . . . . . . . . . 3-5RS-232 Connector . . . . . . . . . . . . . . . . . . . . . . 3-5Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4XMIT LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3TXU - New Configuration . . . . . . . . . . . . . . . . . . . . . . 2-9TXU and TCU
Index-6STRATA TX Operator’s Guidefront panel control switches . . . . . . . . . . . . . . .3-1TXU and/or TCU screens . . . . . . . . . . . . . . . . . . . . .3-19TXU Controls, Indicators, and Connectors . . . . . . . . .3-2TXU Front Panel DC ON COAX Switch . . . . . . . . . . .3-2TXU IF/RF module . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7TXU or TCUsingle-unit applications . . . . . . . . . . . . . . . . . . .2-3TXU Rear Panel DC ON COAX Switch . . . . . . . . . . . .3-5TXU, TCU, and HPUintegrated system . . . . . . . . . . . . . . . . . . . . . . .2-3UUnit vs.System Control . . . . . . . . . . . . . . . . . . . . . . .3-20UNLOCKED message . . . . . . . . . . . . . . . . . . . . . . . . .4-2Using the Monitor Screens in MPEG Output Mode . .3-20VVDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9WWarranty Information . . . . . . . . . . . . . . . . . . . . Notices-iiiAll Products . . . . . . . . . . . . . . . . . . . . . . Notices-iiiProduct Manufactured by MRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notices-iiiProducts Manufactured By Others . . . . Notices-iii

Navigation menu