Microwave Solutions MDU2750 MDU2750 Motion Detector Unit User Manual August 11 2009

Download:
Mirror Download [FCC.gov]
Document ID	2442200
Application ID	C6MrByxI6CWjwOC9wIVLuQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	52.8kB (660017 bits)
Date Submitted	2014-11-12 00:00:00
Date Available	2014-11-12 00:00:00
Creation Date	2014-10-28 11:20:37
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-10-28 11:20:37
Document Title	August 11, 2009
Document Creator	Microsoft® Word 2010
Document Author:	John Hallatt

USER MANUAL
MDU2750
FCC-ID: ROO-MDU2750
IC: 10829A-MDU2750
Description
The Microwave Solutions MDU2750 Motion Detector Unit is an X-Band
microwave transceiver that utilises the Doppler shift phenomenon to "sense"
motion. The unit, contained in a lightweight metal housing, features a dielectric
resonator stabilised FET oscillator, which provides stable operation over a broad
temperature range in either CW or low duty cycle pulse mode and a balanced
mixer for enhanced sensitivity and reliability.
The basic principle of operation consists of detecting the frequency shift between
a transmitted and a received signal reflected back from a moving object within
the field of view of the unit. The unit produces a low level output signal which can
be amplified and processed to provide an audible or visual alarm signal. The
MDU2750 employs low cost surface mount manufacturing techniques which are
field proven as being rugged and reliable.
Absolute Maximum Ratings
Parameter
Supply Voltage
Operating Temperature
Storage Temperature
Symbol
VCC
TOP
TSTG
Rating
+5.25
-40 to +70
-40 to +80
Units
°C
°C
Comment
Performance level not guaranteed
Electrical Characteristics
Parameter
Transmit Frequency
Temperature Stability
Output Power
Antenna Beamwidth
Symbol
fT
∆f
POUT
Min.
10.500
IF Output Offset
Sensitivity
Noise
Supply Voltage
Supply Current
Pulse Width
Operating Temp
VDC
-150
VCC
ICC
4.75
MDU2750 User Manual.doc
TOP
-20
Typ.
10.525
17
72
36
-86
5.00
45
Max.
10.550
+150
10
5.25
60
+55
Units
GHz
MHz
dBm
°
°
mV
dBm
µV
mA
µs
°C
Comment
Pre-set during manufacture.
Over TOP range below
EIRP
-3dB, horizontal with tab down
-3dB, vertical with tab down
Into free space
10dB S/N ratio
In 3Hz – 80Hz bandwidth
Min. duty cycle – 1%
Full specification compliance
Page 1
Coverage Patterns
Connections & Mechanical Outline
Handling Precautions
The MDU2750 is sensitive to damage from ESD.

Normal precautions as usually applied to CMOS devices are sufficient when handling
the module.
 Touching the connection points should be avoided before soldering the module into circuit.
 Using a multimeter (e.g. for resistance measurement) between any of the connection
points may cause damage to the module.
Certification
Microwave Solutions Ltd. has established and maintains a Quality System that has been audited by BSI and holds ISO
9001:2008 approval under certificate FM56058.
The MDU2750 complies with the requirements of the RoHS Directive European Union Directive 2011/65/EU and with
the requirements of the REACH Regulations EC 1907/2006.
MDU2750 User Manual.doc
Page 2
OEM Responsibilities
Manufacturers of mobile or fixed devices incorporating MDU2750 modules are authorized to use the FCC Grants and
IC Certificates of the MDU2750 modules for their own final products under the conditions referenced in this
document. It is the responsibility of the manufacturer of the final product to ensure that the MDU2750 module is
operated within the approved conditions shown below. If the FCC/IC label of the module is not visible when the
module is installed inside the final product then the outside of the final product must also display a label stating
"Contains FCC ID: ROO-MDU2750" and "Contains IC: 10829A-MDU2750".
Approved Operating Conditions to meet FCC/IC requirements
The MDU2750 module can be operated in full compliance with FCC/IC requirements (depending on the characteristics
of the final product) under the following conditions:
1) The power supply voltage provided to the module (at the module terminals) must be maintained within the
specified range of +5 ± 0.25 volts under all conditions of AC line voltage irregularities, battery voltages,
ambient temperatures and worst case load conditions.
2) If the module is operated under pulsed conditions, the rise and fall times of the power pulse shall be less
than 1 µs and, during the pulse, the power supply voltage shall be maintained within the limits of 1) above
under all conditions.
3) A minimum separation distance of 1.6cm is required between the user and the module when operating at
100% duty cycle.
4) If the final product is designed for use in any situation except in motor vehicles or on aircraft the module can
be operated with any duty cycle up to and including 100% (averaged over 100ms).
5) If the final product is designed for use in motor vehicles or on aircraft, the module can be operated with a
maximum duty cycle of 100% (averaged over 100ms) as long as the final product includes features to prevent
continuous operation (as defined in the FCC Rules and Industry Canada Standards).
FCC and Industry Canada statements:






This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This device may only be operated using the approved integral antenna.
This device complies with FCC and Industry Canada radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance.
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by Microwave Solutions Ltd. may void the user's authority
to operate this equipment
In the event that these conditions or the Approved Operating Conditions above cannot be met, then the FCC
and Industry Canada certifications are no longer considered valid and the FCC ID and IC Certification Number
cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate certification.
MDU2750 User Manual.doc
Page 3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Language                        : en-GB
Tagged PDF                      : Yes
Title                           : August 11, 2009
Author                          : John Hallatt
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:10:28 11:20:37+00:00
Modify Date                     : 2014:10:28 11:20:37+00:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools