Midland Radio BTSKI Bluetooth stereo headset with intercom User Manual

Midland Radio Corporation Bluetooth stereo headset with intercom

UserManual.wiki >

Midland Radio >

BTSKI User Manual

User Manual

UK1INDEXTechnical specications of Midland BTSKI ...................................................................................2Charging batteries ............................................................................................................................ 3Description of the BT SKI device and tting systems .................................................................3 Description of the BT SKI device ....................................................................................................3 Fitting your BT SKI Earwarmer system ........................................................................................... 4 Fitting and wiring your BT SKI Universal Helmet system ...............................................................5Switching your Midland BTSKI On and Off .................................................................................... 7Adjusting the volume ....................................................................................................................... 7Pairing with Bluetooth devices .......................................................................................................7Using the features of the Bluetooth devices .................................................................................8 Using the telephone feature ............................................................................................................8 Using the MP3 player feature of the mobile phone .........................................................................9 Using the intercom feature ..............................................................................................................9Resetting all paired devices ..........................................................................................................10Using the wired audio input ..........................................................................................................10 Using an i-Pod/MP3 player ........................................................................................................... 11 Using a Two Way Radio transceiver ............................................................................................. 11Special congurations ................................................................................................................... 11 Enabling/Disabling the VOX feature (Intercom and telephone) .................................................... 11 Wired connection always on .........................................................................................................12Recommendations for specic uses ............................................................................................ 12 Recommendations for using a PMR446 transceiver ....................................................................12 Use at your own risk .....................................................................................................................13Warranty ..........................................................................................................................................13Light and sound signal/ unit functions ........................................................................................15

2Midland BTSKI Thank you for purchasing Midland BTSKI Intercom, the wireless Intercom system designed for leisure users that want to practice winter sports without giving up the comfort of Bluetooth communications. Thanks to Bluetooth technology, Midland BT SKI allows you to make and receive calls, listen to music and connect with another Midland BT SKI device hands-free, thanks to the Intercom feature. Versions: › Midland BT SKI Earwarmer › Midland BT SKI Universal Helmet Content of the BT SKI “Earwarmer” packaging › 1 BTSKI device › 1 earwarmer with two stereo speakers and 1 microphone with boom › 1 Velcro strip to x the unit onto the helmet › 1 Stereo audio cable to connect an iPod/ or other models of MP3 players › 1 Mini USB wall-mounting power supply Content of the “Universal Helmet”packaging › 1 BTSKI device › 1 Audio kit with two stereo speakers and 1 microphone with boom › 1 Velcro strip and 1 bi-adhesive plate to x the unit onto the helmet › 1 Stereo audio cable to connect an iPod/ or other models of MP3 players › 1 Mini USB wall-mounting power supplyTechnical specications of Midland BTSKI › Bluetooth ver. 2.0 stereo (Headset/Handsfree/A2DP protocol) › AGC system automatically controls the volume in relation to background noise › Voice (VOX) or manual activation of the communication › Mobile phone connection › Manual controls to enable: telephone, intercom and wire connection › Fully waterproof/snowproof › Lithium battery with 8 hours talk time › Recharge time: app. 4 hours › Intercom: max coverage of app. 200mt outdoorsBluetooth connections: › To a mobile phone/MP3 player › With another BTSKI device for Intercom communicationsWire connections: › For stereo audio input (iPod/MP3 player) › For PMR446 transceivers (with optional cable)Attention: before using BTSKI for the rst time, remember to recharge it for at least 5/6 hours.Attention: Midland BTSKI is designed to withstand rain and snow. However, if it is raining, always verify that the rubber caps protecting the sockets are fully tted.

UK3Charging batteriesMake sure that the unit is fully charged before use. Allow at least 5-6 hours for a full charge before using the unit for the rst time. Normally, after the rst time, it takes 4 hours for a full charge.Charge the unit by inserting the wall-charger into the charging socket (lift the rubber cover to insert the plug).The red LED on the unit will start ashing when charging begins. Let the device charge until the blue LED turns on.When the charge is complete, release the devi-se from the charger.Attention: every time the mini USB rechar-ging plug is inserted (or detached), the devi-ce automatically turns off. To use the device while it is in charge, you should turn it on again with the plug inserted.Description of the BT SKI device and tting systemsDescription of the BT SKI deviceThe BTSKI has 3 multifunction buttons on the front and 3 wired connections in the lower section.Description of the button features: › Control: to manage mobile phone features and the Intercom function › Volume+: enables you to increase the volu-me › Volume -: enables you to decrease the vo-lumeDescription of the wired connections › Charger jack: enables to recharge the unit using a standard mini USB power supply › Audio kit jack: enable to connect an audio kit (stereo headset and microphone) › Auxiliary audio jack (AUX): can be used to connect an audio source, like a stereo iPod/MP3 player, or a PMR446 transceiverAttention: for a better sound quality be sure that the plug has been correctly and deeply inserted.Charger jack Audio kit jackAuxiliary audio jackVolume+Volume -ControlAntenna

4Fitting your BT SKI Earwarmer system The Earwarmer audio system includes two ultra-at stereo speakers and one microphone with boom, all assembled into a soft and warm headset.Midland BT SKI is the best solution for Bluetooth communications, designed to be used without helmet or with semi-rigid ski helmets.Fitting and removing your Midland BT SKIThe BT SKI can be easily tted by sliding it downwards so that it ts into the slot of the xing device. BT SKI is maintained in position thanks to the xing clip located on the upper section (A).To detach the BT SKI, simply press the xing clip and push the unit upwards.Using the BT SKI without helmetAfter have xed your BTSKI on its suitable tool and have inserted the audio kit plug into the central socket, wear your headset as shown in the gure. Please, be sure to have placed the microphone in the right way, with the white sign oriented towards your mouth. Using the BTSKI with a semi-rigid helmetTo place the BT SKI into a semi-rigid helmet you should rst of all remove the little triangular pads, used to cover the ears in most of helmets on sale, and then put your helmet directly on the BT SKI device.If your helmet is not equipped with the two removable pads, you could anyway mount your BT SKI system by using the supplied Velcro-band. Be sure to x the Velcro-band as shown in the gure.A

UK5Now, x the BT SKI on the Velcro-band. Wear your headset, insert the connection cable of the headset into the BT SKI device and wear the helmet.Fitting and wiring your BT SKI “Uni-versal helmet” system Midland BT SKI thanks to the “Universal Helmet” audio kit can be mounted on every kind of helmet: rigid and semi-rigid ones. The “Universal helmet” audio system is composed of two ultra-at high performance stereo speakers and one microphone with boom (integrated to the speaker on the right).To wire the helmet. Thanks to the functional Velcro band (or the bi-adhesive plate), it is possible to x the speakers inside the ear pad (the nearest they are to your ears, the better will be the sound quality) Wires can be hidden inside the padding. To achieve the best microphone performance, be sure to have placed the boom mike the nearest to your mouth.It is very important to keep the sponge on the microphone in order to reduce wind noises or background interferences.

6The best known and distribu-ted helmet brands on the mar-ket are designed to contain the speaker inside the padding. The Universal Helmet solution can be perfectly placed inside; just put the speakers into the special compartment in corre-spondence to your ears.The majority of the mo-dels have a pocket on each side(with a Velcro closure); remove the foam rubbers and replace them with the speakers. From the little opening of the right, let the boom microphone and the connection plug exit. Adjust the boom microphone the nearest to your mouth.Other helmet models have a little clasp under the soft padding. In this case, open the zip and place the speakers near your ears. Let the boom mike exit from the end of the zip and adjust it. The plug should exit from that little opening too in order to connect it to your BT SKI.To x the BT SKIIn case you have a semi-rigid helmet, you should mount your BT SKI system by using the supplied Velcro band.Be sure to x the Velcro band on the right side of the helmet between the closing laces, as shown in the gure below.Now, x the BT SKI on the Velcro band by slipping it down.Insert the connection cable into the Audio kit plug of the BT SKI device.

UK7In case you have a rigid helmet, you should mount your BT SKI system by using the bi-adhesive plate.This little and practical mounting system allows you to t the BT SKI on the rigid surface of the helmet. Just clasp and slide the BT SKI device down and connect it to the audio kit. Switching your Midland BTSKI on and offSwitching the unit on: › Press and hold “Control” button down for approximately 3 seconds until the BLUE in-dicator lights.Switching the unit off: › Press and hold both “Control” and “VOL-” buttons together for approximately 3 seconds until the RED indicator ashes 3 times, thus lessening the chances that you might turn off the unit accidentally (especially whilst wea-ring heavy gloves).Adjusting the volumeYour Midland BT SKI uses AGC technology, which automatically adjusts the listening volume in relation to background noises.However, it is also possible to manually adjust the volume by means of the “Volume+” and “Volume -“buttons.Attention: volume can be adjusted only when an audio kit connection is active. (In-tercom, music, phone call… )Pairing with Bluetooth devicesYour Midland BT SKI is a Bluetooth unit that can be paired with other Bluetooth devices, such as a mobile phone or another BT SKI device for Intercom communications.Before performing this procedure, it is necessary to set BT SKI into the Setup mode.Setup modeSwitch off the BT SKI device. Press and hold down the central button “Control” for about 7 sec. until the red indicator switches on permanently. BT SKI is now in “Setup” mode and can therefore be paired with other devices.Exiting from the Setup modeTo exit the Setup mode double click the “Control” button. Once the red light turns off, the blue led starts blinking.

UK9Using the MP3 player feature of the mobile phoneMany mobile phones are now designed to be used as stereo MP3 players. The BT SKI device fully supports the A2DP and AVRCP protocols that enable you to listen to stereo music and remotely control your mobile phone’s MP3 player. You can even use the buttons on the BT SKI unit to control the following play options: Play, Pause, Forward and Backward.Available controls: › To play/pause music, double click the “Con-trol” button. › To skip forward to the next song, keep pressed the “Volume+” button. › To skip backwards to the previous song, keep pressed the “volume-“ button. › To enable your connected MP3 Player (ADP/AVRCP), press and hold down the “Vo-lume +” and “Volume-“ buttons for 3 seconds (this feature is active by default). › To disable the MP3 player, press and hold down the ”Volume+” and “volume-“ buttons (2 beeps will conrm it).Priority: the music listening mode has the lo-west priority. Therefore, it will always be disa-bled when another type of communication is enabled.Using the intercom feature To use the Intercom feature, be sure both BT SKI units are turned on and previously paired together.Pairing with another BTSKI devicePlace both BT SKI units in Setup mode (red indicator permanently on) Press the “Volume +” button on the rst unit until the RED and BLUE lights begin to ash rapidly and alternately.Then press the “Volume –“button on the second unit until the RED and BLUE lights begin to ash rapidly and alternately.Now both BT SKI units are trying to pair to each other.When successfully paired, the blue led of each device will light for 1 sec and go back to setting mode (red light always on) waiting for additional pairing or setting procedures.To use the two devices, exit the setting mode.Double click on the “Control” button. The red light will quit and the blue light will begin to ash. Now you can use your BT SKI.Priority: Intercom communications always have a higher priority, compared to other communi-cations, with the only exceptions being Tele-phone.Therefore, the Intercom feature automatically disables all other communications.The intercom feature is disabled during a phone call, and is automatically re-enabled as soon as these communications end.Volume+forwardVolume -backwardControlPlay/Pause

10Attention: some mobile phone release the line after a few seconds, which means that the Intercom feature may not be immediate-ly available.The Intercom feature can be enabled in two ways:Manual activation:› Press “Control” button, on one of the two units. Communication is enabled and re-mains active until you press the “Control” button again. You will hear 1 audio tone when the Intercom feature is enabled and 2 audio tones when it is disabled.Voice activation (VOX):› This is enabled by default. To start an Inter-com communication, simply start talking. Attention: every time the mini USB re-charging plug is inserted (or detached), the device automatically turns off. To use the device while it is in charge, you should turn it on again with the plug in-serted. The communication will remain active for all the time you are talking. If there is no conver-sation, the Intercom is automatically closed after 20 seconds. To re-open it, simply start talking again. When the Intercom is “VOX” activated, you can decide to disable it before the predened time, simply by pressing the ”Control” button once.› To disable the voice activation mode, follow the instructions provided in the “Special con-gurations” section.DistanceTwo Midland BT SKI units can communicate up to a maximum range of approximately 200meters outdoors. The maximum coverage depends on the presence of obstructions in the area or on the head orientation.Resetting all paired devicesSometimes you may nd it necessary to delete all the pairing references stored in the BT SKI unit (reset operation).To perform this operation, switch off the BT SKI and keep pressed the “Control” button. The red led turns on. Simultaneously press and hold down the “Volume +” and “Volume –“ buttons for 4 seconds.The Blue Light will be lit on for 1 sec.This procedure deletes all the paired Bluetooth devices stored in the memory and it is therefore possible to start a new “clean” pairing session.Using the wired audio inputYour Midland BT SKI is also supplied with a wired audio input (labeled AUX), that can be used to connect an audio source, like an iPod (or any other MP3 Player) or a PMR446 transceiver for communications in group or for a coverage increase. The wired audio input allows a higher range of coverage respect to what granted with Bluetooth technology.Priority: the wired audio input has the lowest priority when compared to the other Bluetooth connections (including the Intercom) and will therefore always be disabled when another Bluetooth communication is opened.

UK11Using a i-Pod/MP3 PlayerListening to musicTo listen to music from the wired input, connect the audio source using the cable supplied with the BT SKI unit. The volume level is automatically adjusted by the AGC system, which means that you only need to adjust the volume of your iPod/ MP3 player to a level that will allow you to listen to music in normal speed.Attention: it is not recommended to set the maximum volume on the MP3 player. Hint: We recommend that you perform a few tests adjusting the volume of your iPod/MP3 player so at the normal speed the Headset vo-lume is suited to your needs. The AGC system will automatically increase the volume on higher speed. Make a note to remember this setting for future trips.Attention: the volume adjustment, (“Volu-me+” and “Volume –“) buttons, cannot be used to adjust the volume of the wired audio source(eg MP3 player).Enabling/disabling the wire inputThe wire input can be enabled and disabled › Enabling: double click the “Control” button (you will hear one audio conrmation tone).› Disabling: double click the “Control” button(you will hear two audio conrmation tones). Attention: this function is available only if there is no music active via Bluetooth.Using a Two Way Radio transceiverTo be able to use the transceiver, it is necessary to purchase a specic cable (sold separately) in order to connect the radio to your Midland BT SKI.Some manufacturers radios use a different pin conguration, so we recommend that you ask your dealer as to which cable is best suited to your needs.To communicate via the attached radio, press the transmission Press To Talk (PTT) button to speak and release it to listen. It is not possible to talk and listen simultaneously. Communications can be activated also without pushing the PTT button, by enabling the VOX function. Special congurationsSome Midland BT SKI features can be congured to suit specic needs › Enabling/Disabling the VOX feature (Inter-com and telephone) › Wired connection always onEnabling/Disabling the VOX feature (Intercom and telephone)Enabling the intercom by voice (VOX)The Intercom feature can be enabled both manually and vocally (VOX). The VOX activation is inuenced by the background noise and therefore by the speed. For optimum results, it is possible to choose one of the following four microphone sensitivity levels: high, medium, low and very low. The default setting of BT SKI is “high”. It is also possible to disable the VOX feature in order to

12activate the Intercom and phone call answering features in manual mode only.Adjusting the sensitivity of the microphone (VOX)1. Enter the Setup mode: Switch your BTSKI off. Press and hold down the central button (Con-trol) until the red indicator switches on perma-nently. Your BT SKI is now in “Set up mode”.2. Press the “Volume+” and “Control” buttons till the red indicator will turn to steady blue.3. Now, press “Volume +” or “Volume -“to in-crease or reduce sensitivity. Every time you press the Volume buttons the RED light will ash for conrmation. When you reach the end of the upper and lower limit, the RED light will not ash.4. Double press the “Control” button; the Blue light will ash several times, in order to let you know the selected sensitivity: once = VOX disabled Twice = very low sensitivity 3 times= low sensitivity 4 times= medium sensitivity 5 times = high sensitivity Default = high sensitivity5. The light indicator is now back to steady RED (“Set up mode”) and the changes are conr-med6. If needed, you can adjust again the sensitivity repeating the steps from point 2, otherwise exit the Setting mode by double clicking the “Control” button. Once the red light turns off, the blue led starts blinking. Now you can use your BT SKI.Disabling the VOX feature (Intercom and telephone)Follow all the procedure described in the previous steps and choose the option 1 (VOX disabled). You will see the blue led blinks once.Wired connection always onThis feature let’s you keep the wired connection always on, even when the intercom is open. This feature can be useful when you connect a PMR446 transceiver.Enabling: › Enter the “Setup” mode. › Press the “Volume+” and “Volume -” buttons for one second. The blue LED will ash once. › To exit the “Setup” mode double press the “Control” button.Disabling: › Follow the same procedure up described; now the blue LED will ash twice › To exit the “Setup” mode double press the “Control” button.Recommendations for specic usesRecommendations for using a PMR446 transceiver If you wish to use a PMR446 transceiver for group communications and simultaneously maintain the Intercom feature enabled between two BT SKI devices, you must remember that the Intercom feature is enabled every time you speak by means of the BT SKI’s VOX feature.Consequently, radio communications will be disabled whilst you are talking with somebody,

UK13because they have a lower priority compared to Intercom communications. This can be prevented by enabling the “Wired connection always on” or disabling the VOX feature.Disable the VOX feature, as explained in the previous section, to make sure that the intercom will not automatically be activated when you speak on the PMR446. To enable the Intercom feature when using this conguration, you will have to press “Control” button manually. (This operation disables radio communications that will be automatically re-enabled when the Intercom feature is disabled).Attention! If you disable the VOX feature, you will only be able to answer incoming phone calls by pressing the “Control” but-ton.Use at your own riskThe use of the headphone-headset will impair your ability to hear other sounds and others around you. Listening to music or speaking on a telephone may prevent you from hearing others around you and distract you from riding safely. The use of such headphone-headset while skiing or ri-ding may endanger you and others, and its use, in some areas, could not be allowed.Using this headset at a high volume may result in permanent hearing loss. If you experience ringing in your ear or any other hearing related pain, reduce the volume or discontinue using this device. With continued use at high volume, your ears may become ac-customed to the sound level, which may result in permanent damage to your hearing. Please use this device at a safe volume level.WarrantyThe Warranty does not limit the user’s statutory rights under applicable National laws relating to the sale of consumer products.The warranty period starts at the time of Prod-uct’s original purchase by the rst end-user and lasts 24 months. It is only valid and enforceable in the country where the user has purchased the product pro-vided that the same product has been intended for sale in that country by the manufacter.To make use of this warranty, it is necessary to return the defective product with its original package together with the original sales receipt to the authorized service centre.The warranty totally covers the device in all its parts and the workmanship necessary to repair it.The warranty does not cover defects or dam-ages caused to the Product by misuse with, or connection to, any accessory or software not produced or supplied by the manufacturer or by use of the product for any other use than for intended use of the product.The warranty is not enforceable if the product has been dismantled, modied or repaired by anyone other than the authorized service cen-tre or if it is repaired using unauthorized spare parts.Moreover, the warranty is not valid and no pro-test can be made if the product has been modi-ed or altered respect to its original purpose.Nobody will be indemnied for the inactivity period of the device nor can expect refund or claim for direct or circumstantial damages due to an inappropriate use of the device.

14European CE Notice Certication and Safety Approvals InformationThis product is CE marked according to the RTTE Directive (99/5/EC) and is free use in all the EU countries.Users are not permitted to make any changes or modications to the device.Modications which are not expressly approved by the producer invalidate the warranty card.For further information, please go to our web-site www.cte.itRSS-Gen & RSS-210 statement:This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two condi-tions: (1) this device may not cause interferen-ce, and (2) this device must accept any inter-ference, including interference that may cause undesired operation of the device.RSS-102 Statement:“This equipment complies with Industry Canada radiation exposure limits set forth for an uncon-trolled environment.”FCC statement:“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera-tion.”Warning! Changes or modications to this unit not expressly approved by Midland Radio Cor-poration could void the user’s authority to ope-rate the equipment.

UK15LIGHT AND SOUND SIGNALS LED indication Status GENERAL None Unit is switched off or full charged when connected to the power supply Single Blue ash every 3 seconds Unit being turned on/ Unit in working mode Triple red ash Unit being turned off Single Red ash every 3 seconds Standby - low battery RED and BLUE (together) every 3 se-conds Active (Intercom, phone call or Bluetooth connection in progress) RED and BLUE (together) and one ash of RED light every 3 seconds Active but low battery Single red ash every 2 seconds Unit in charge when connected to the power supply SETUP Steady Red Setup mode Rapid Red-Blue alternating ash Pairing mode (searching for devices) Steady Blue for two second Successful pairing/ Reset paired devicesAudio signals Status Ascending tone (low-high) Unit being turned on Descending tone (high-low) Unit being turned off Enable/Disable the Intercom 1 tone = enabled / 2 tones = disabled 1 tone Specic feature turned on 2 tones Specic feature turned off UNIT FUNCTIONSIf you want to... …do this GENERAL Turn on the unit Press the Control button for 3 seconds at least (start Blue ash) Turn off the unit Press the Control and VOL- buttons together for 3 secon-ds (triple Red ash) Increase the volume Short press the Volume Up control

Decrease the volume Short press the Volume Down control MOBILE PHONE Answer a call Short press of the Control button / say a word Reject a call Long press the Control Button / remain silent until the rings stop Terminate a call Short press the Control Button Voice Dial Short press the Control button and state the name of the person to call (only if your BTSKI has not been paired with another BTSKI device). Redial Last number Long press of the Control button INTERCOM (if paired with another BTSKI device)Start using the Intercom Start talking/short press the Control button Stop using the Intercom Stop talking (after 20 sec. you will return to stand by mode)/Short press the Control buttonBLUETOOTH MP3 player of the mobile phone Activate the MP3 player Press and hold down the VOL+ and VOL- buttons for 3 seconds Play and Pause Double click the Control button Forward (next song) While the music play, keep pressed of the VOL+ button for 3 sec.Backward (previous song) While the music play, keep pressed of the VOL- button for 3 sec. Deactivate the MP3 Player Press and hold down the VOL+ and VOL- buttons for 3 secondsWIRED CONNECTION Activate /Deactivate Double click the Control button (only if Music via Blueto-oth is disabled) SETUP/PAIRING Enter SETUP mode Press the Control button for 7 seconds while the unit is off Exit SETUP mode While in Setup mode, double click the Control button. The Red light will turn off and the Blue light starts ashing.Pairing a Phone While in Setup mode, press the Control button until the LED light ash Red and Blue alternately

UK17Pairing your BTSKI with another BTSKI device While in Setup mode, press the Volume + on one unit (the light will ash Red and Blue alternately), press the Volu-me- on the other unit (the light will ash Red and Blue al-ternately). On a successful pairing, both light turn to Blue for one second.Reset all paired devices While in Setup mode, long press he Volume + and he Vo-lume -. On a successful reset, the Blue light will turn on for two second.SPECIAL SETUP CONFIGURATION Change VOX sensitivity or disable itWhile in Setup mode, press short the Control and VOL+ buttons (blue light on). Now, press “Volume +” or “Volu-me-“ to increase or reduce sensitivity. Double click the Control button to visualize the VOX status. Go back to the SETUP mode (Red light always on).VOX STATUS (Blue light ashing):Once = VOX disableTwice = very low sensitivity3 times = low sensitivity4 times = medium sensitivity.5 times = high sensitivityWired connection always onEnabling: In “Setup” mode, press the “Volume+” and “Vo-lume -” buttons for one second. The blue LED will ash once.Disabling: Follow the same procedure up described; now the blue LED will ash twiceCTE International herewith declares that the product complies with the essential requirements of EC Directive 99/05/EC; the declaration of conformity of the device can be consulted onto www.midlandradio.eu

Navigation menu