Midmark 9A408T Wireless Control for Universal Procedure Table User Manual Wireless hand Foot Control pmd

Download:
Mirror Download [FCC.gov]
Document ID	777843
Application ID	FC0MKOlGrTtszHjrwrc3UQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.81kB (110168 bits)
Date Submitted	2007-04-06 00:00:00
Date Available	2007-04-06 00:00:00
Creation Date	2007-03-08 15:29:13
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2007-03-08 15:29:51
Document Title	Wireless hand-Foot Control.pmd
Document Creator	PageMaker 7.0
Document Author:	mbeckner

Safety Information
Symbols
Keep Dry
Fragile
Limited Warranty
General Information
SCOPE OF WARRANTY
Intended Use
Midmark Corporation (“Midmark”) warrants to the original purchaser its
new Alternate Care products and components (except for components
not warranted under “Exclusions”) manufac-tured by Midmark to be free
from defects in material and workmanship under normal use and
service. Midmark’s obligation under this warranty is limited to the repair
or replacement, at Midmark’s option, of the parts or the products the
defects of which are reported to Midmark within the applicable warranty
period and which, upon examination by Midmark, prove to be defective.
This product is intended to ...
User’s Guide
Wireless Hand / Foot Controls
9A408
APPLICABLE WARRANTY PERIOD
IPX1
Protected against dripping water
The applicable warranty period, measured from the date of delivery to
the original user, shall be one (1) year for all warranted products and
components.
EXCLUSIONS
Emergency Stop
FCC Compliance Statement
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
Any modifications to this product may violate the rules
of the Federal Communications Commission and make
operation of the product unlawful.
This warranty does not cover and Midmark shall not be liable for the
following: (1) repairs and replacements because of misuse, abuse,
negligence, alteration, accident, freight damage, or tampering;
(2) products which are not installed, used, and properly cleaned as
required in the Midmark “Installation” and or “Installation / Operation
Manual for this applicable product. (3) products considered to be of a
consumable nature; (4) accessories or parts not manufactured by
Midmark; (5) charges by anyone for adjustments, repairs, replacement
parts, installation, or other work performed upon or in connection with
such products which is not expressly authorized in writing in advance
by Midmark.
Authorized CE Representative
Countries in the EEC should direct all questions,
incidents, and complaints to Midmark’s authorized
CE Representative listed below:
Promotal
22, Rue de St. Denis
53500 Ernee,
FRANCE
Phone: 33-2-430-517-76
Fax: 33-2-430-569-10
EXCLUSIVE REMEDY
Midmark’s only obligation under this warranty is the repair or replacement of defective parts. Midmark shall not be liable for any direct,
special, indirect, incidental, exemplary, or consequential damages or
delay, including, but not limited to, damages for loss of profits or loss
of use.
NO AUTHORIZATION
No person or firm is authorized to create for Midmark any other
obligation or liability in connection with the products.
Calling for Service
If service is required, contact your Midmark dealer
or to locate your nearest service provider, log onto:
http://www.midmark.com
To contact Midmark directly:
1-800-Midmark (1-800-643-6275)
8:00 am until 5:00 pm Mon-Fri (EST)
THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND
IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES
O F ANY KIND INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
PURPOSE. THIS WARRANTY IS LIMITED TO THE REPAIR
OR REPLACEMENT OF DEFECTIVE PARTS.
This guide outlines basic operation of the wireless
hand / foot control accessory. If service is required,
contact your authorized Midmark dealer.
Dealer (name / phone):
___________________________________
___________________________________
___________________________________
___________________________________
SF-1487 REV. A1
Date of Purchase:
Midmark Corporation
60 Vista Drive
Versailles, OH 45380-0286
Phone: 937-526-3662
Fax: 937-526-5542
midmark.com
_____________________
© Midmark Corporation 2007
003-xxxx-00 Rev. A
Specifications
Batteries: ................................. AAA (qty: 2)
(Note: Battery access cover is located on back of controller)
This procedure is only required if there is a malfunction, or
if you are attempting to use the controller with a chair other
than the one it was originally associated with.
Association Procedure:
A. Using the wired hand / foot control, press & hold
the Stop & Home buttons simultaneously.
Range of Operation ................. 20 ft (6 m) radius
(after two seconds you will hear a single “beep”)
B. Using the wireless hand / foot control, press & hold
the Stop & Home buttons until you hear three “beeps”.
(one long “beep” indicates the association failed. Repeat Steps A & B)
Troubleshooting
C. Check for proper operation of wireless controllers.
Note:
Step B must be performed within 10 seconds of Step A,
failure to do so will cause the procedure to fail.
• When any button is pressed, hand / foot control
sounds a single “beep”. (All functions operate)
Cause:
Low Battery
Solution: Replace batteries
• When any hand / foot control button is pressed,
nothing happens. (No “beeps”, no movement, etc.)
Causes: 1. Batteries completely dead
2. Wireless controller has lost
“association” to chair.*
Solution: 1. Replace batteries
2. Perform Association Procedure*.
* The wireless controllers will only function with the
chair they have been “associated” with. This
prevents unwanted movement in locations with
more than one chair.
If further service is required,
contact your authorized Midmark dealer.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseThumbs
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2007:03:08 15:29:13-05:00
Creator Tool                    : PageMaker 7.0
Modify Date                     : 2007:03:08 15:29:51-05:00
Metadata Date                   : 2007:03:08 15:29:51-05:00
Format                          : application/pdf
Creator                         : mbeckner
Title                           : Wireless hand-Foot Control.pmd
Document ID                     : uuid:e5fc9de5-10bd-41c8-9a0b-36b7d67ca550
Instance ID                     : uuid:cef8a34d-4ce1-4111-8bb2-bab927f57780
Page Count                      : 2
Page Layout                     : SinglePage
Author                          : mbeckner

EXIF Metadata provided by EXIF.tools