Miele Cs 1122 E Specification Sheet Microsoft CS1122E_Specifications [Compatibility Mode]

: Miele Miele-Cs-1122-E-Specification-Sheet-747826 miele-cs-1122-e-specification-sheet-747826 miele pdf

Open the PDF directly: View PDF .
Page Count: 4

Product and Cut-out Dimensions Page 1 of 4

CS 1122 E Ceramic Double Burner CombiSet

CS

1122

E

Ceramic

Double

Burner

CombiSet

Location Codes

1– Spring clips

2– Appliance front

3– Installation height

4–Power supply box with connection cable Length =47 1/4”(1200 mm)

4Power supply box with connection cable, Length 47 1/4 (1200 mm)

208 V, 60 Hz, 20 A fuse rating

240 V, 60 Hz, 15 A fuse rating

Ensure that the power outlet is accessible after installation

5– Rating label – Ensure that the electrical supply matches the rating. Adhere rating label sticker supplied with the

appliance into the manual.

Shipping weight 21 lbs (9.5 kg)

Shipping dimensions 23” (584 mm) L x 19” (483 mm) W x 8” (203 mm) H

Notes

Indoor use

The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of

the appliance provides a sufficient seal for the countertop.

All installations must be done in accordance with local codes.

Drawing is not to scale Specification Sheets OJS 02212012

Product and Cut-out Dimensions Page 2 of 4

CS 1122 E Ceramic Double Burner CombiSet

Cut-out Dimensions

For two CombiSet Appliances Cut-out Dimensions

For three CombiSet Appliances

CS

1122

E

Ceramic

Double

Burner

CombiSet

For the installation of two appliances the

width of the countertop cut-out D is the sum

of A and C.

For the installation of three appliances the

width of the countertop cut-out D is the sum

of A and B and C.

A, Band C= appliance width

11 5/16” or 15”

(288 mm or 380 mm)

minus 5/16” (8 mm) to allow for the overhang

D = width of the countertop cut-out

If more than three appliances are being

installed, you will need to add, A, B or C for

each additional appliance.

Sample calculations for a countertop cut-out for three appliances

A

appliance width

minus 5/16"

(8mm)

B

appliance width C

appliance width

minus 5/16"

(8mm)

D

countertop

cut-out

11" (280 )

11 5/16" (288 )

11" (280 )

33 3/8" (848 )

11"

(280

mm

)

11

5/16"

(288

mm

)

11"

(280

mm

)

33

3/8"

(848

mm

)

11" (280 mm) 15" (380 mm) 14 5/8" (372 mm) 40 5/8" (1032 mm)

14 5/8" (372 mm) 11 5/16" (288 mm) 11" (280 mm) 37" (940 mm)

14 5/8" (372 mm) 15" (380 mm) 14 5/8" (372 mm) 44 1/4" (1124 mm)

Location codes

2– Support bars (Accessory, Item - 27996029D CSZL 1500 (Includes cover ))

Notes

All installations must be done in accordance with local codes.

Drawing is not to scale Specification Sheets OJS 02212012

Product and Cut-out Dimensions Page 3 of 4

CS 1122 E Ceramic Double Burner CombiSet

CS

1122

E

Ceramic

Double

Burner

CombiSet

The illustration above represents the attachment of spring clips 1 and support bars 2for 3

appliances

Spring Clip installation

on wood or solid

surface countertop

Place the supplied

spring clips

1

and the

Spring Clip installation

on a granite

countertop

Position and attach

the spring clips

1

and

An additional support bar is required for each additional appliance. The position for the

attachment of an additional support bar depends on the width of appliance B.

spring

clips

1

and

the

support bars 2 at the

marked positions as

shown above, by

laying them on the

upper edge of the cut-

out and then securing

them with the 1/8” x 1”

the

spring

clips

1

and

the support bars 2

with strong double-

sided tape 3

Coat the side and

lower edges of the

spring clips with

silicone.

Location Codes

1 – Spring Clips

2 – Support bars (Accessory, item - 27996029D CSZL 1500 (Includes cover 4))

(3.5 x 25 mm) screws

(supplied) Fill the space between

the support bars and

the countertop with

silicon

3 – Space between support bar and countertop

4 – Cover

Notes

All installations must be done in accordance with local codes.

Drawing is not to scale Specification Sheets OJS 02212012

Product and Cut-out Dimensions Page 4 of 4

CS 1122 E Ceramic Double Burner CombiSet

1– Wall frame

2– Wall covering

x = thickness of the wall covering

3– Countertop

4

–

Counterto

p

cut-out

Safety distances to back wall

CS

1122

E

Ceramic

Double

Burner

CombiSet

If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out

and the covering, since high temperatures can damage these materials.

If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out

and the wall covering must be a minimum of 2

"

(50 mm)

p

5– Minimum safety distance

with flammable materials 2" (50 mm)

with non-flammable materials 2" (50 mm) minus x

Safety distances to surrounding cabinetry

Recommended

Not Recommended Not Permitted

and

the

wall

covering

must

be

a

minimum

of

2

(50

mm)

.

For coverings made of non-combustible materials (such as metal, marble, granite or ceramic tiles) the

minimum safety distance between the countertop cut-out and the wall covering must be 2" (50 mm) minus the

thickness of the covering.

For example: thickness of wall covering 9/16" (15 mm) 2" (50 mm) - 9/16" (15 mm) = minimum safety distance

1 3/8" (35 mm).

Recommended

Not

Recommended

Not

Permitted

The appliance should only be installed as shown in the above illustrations while maintaining the

required safety distances shown. Do not install the appliance between two tall cabinets, this is a

fire hazard.

A distance of at least 2” (50 mm) must be kept between the countertop and the rear wall

because of high temperature radiated.

The minimum distance required from the countertop cut-out to a side wall or tall cabinet right or

left 2” (50 mm) (Location code 1)

Safety distance above the appliance

The minimum safety distance given by the hood manufacturer

must be maintained between the combiset and the hood above

it. See the installation instructions for the hood for these safety

measurements.

Notes

All installations must be done in accordance with local codes.

Drawing is not to scale Specification Sheets OJS 02212012

If the hood manufacturers instructions are not available or if

flammable objects are installed over the combiset (e.g.

cabinets, utensil rail, etc.), a minimum safety distance of 30”

(760 mm) must be maintained.