Miele Km410 Users Manual

KM402 to the manual 6dc7dec7-262b-45a5-af45-f14ac7144736

: Miele Miele-Km410-Users-Manual-222035 miele-km410-users-manual-222035 miele pdf

Open the PDF directly: View PDF .
Page Count: 16

Installation Instructions

KM 400 Electric Cooktop

KM 402 / KM 403 Fryer

KM 408-1 Contact Grill

KM 410 / KM 411 Electric Barbecue

To prevent accidents and

machine damage,

read these instructions

before installation or use.

UV

M.-Nr. 05 060 863

2

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety distance above the appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KM 400 / KM 408-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KM 402 / KM 403 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

KM 410 / KM 411 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Cutting out the countertop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Laying out the support bars and clamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Securing the support bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Wood or Corian countertops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Granite countertops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Securing the spring clamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Wood or Corian countertops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Granite countertops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Locking the appliance into place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Contents

3

Note to the installer:

Please leave this instruction book

with the consumer for the local

electrical inspector’s use.

Installation

The minimum distances given in

these Installation Instructions must

be observed in order to ensure safe

operation. Failure to do so increases

the risk of fire.

To prevent appliance damage, the

cabinetry and venting hood should

be installed first.

The countertop must be bonded

with heat resistant (212 °F/100 °C)

adhesive to prevent distortion.

The cooktops should only be

installed in the illustrations, while

maintaining the required safety

distances shown. Do not install the

cooktop between two tall cabinets, this

is a fire hazard.

a= Minimum safety distances:

KM 400 = 2" (50 mm)

KM 402 / 403= 2" (50 mm)

KM 408-1 = 2" (50 mm)

KM 410 / 411 =10" (250 mm)

Deep fryers must not be installed

next to gas cooktops. Gas flames

can ignite splattering oil. A distance of

at least 12" (305 mm) should be

maintained between these two

appliances.

recommended

not recommended

not allowed

IMPORTANT SAFETY INSTRUCTIONS

4

Cooktops should not be installed

above a dishwasher, washer, dryer,

freezer or refrigerator. The high

temperatures radiated downwards from

the cooktops could damage these

appliances.

This equipment has not been

designed for maritime use or for

use in mobile installations such as

aircraft or recreational vehicles.

However, under certain circumstances

it may be possible for an installation in

these applications. Please contact the

nearest Miele Dealer or the Miele

Technical Service Department with

specific requirements.

Make sure that the power cord to

the cooktop does not come into

contact with any mechanical parts once

the cooktop has been installed.

Safety distance above the appliances

As a general rule there must be a

minimum safety distance of at least 30

inches (760 mm) between the top of the

appliance and any cabinet above it, b.

The minimum distance of combustible

surfaces located above and to the side

of the cooktop, c, is 18" (457 mm).

If the cabinet manufacturer

recommends a different distance, follow

that manufacturer’s recommendation.

The minimum safety distance

between the KM 410 / KM 411 and

the bottom of a venting hood should

be no less than 26" (650 mm).

If more than one appliance is

installed beneath a hood and they

have different minimum safety

distances, the greater distance

should be followed.

Keep this instruction book in a safe

place and pass it on to any future

owner.

IMPORTANT SAFETY INSTRUCTIONS

5

KM 400 / KM 408-1

aClamps

bPlease allow an additional 3/4"

(18 mm) depth below the cooktop for

clearance of the power cord.

Appliance dimensions

6

KM 402 / KM 403

aClamps

Appliance dimensions

7

KM 410 / KM 411

aClamps

Appliance dimensions

8

Cutting out the countertop

All Miele combisets have the same

length and width. Make sure that there

is enough room beneath the countertop

to allow for the depth of the various

appliances. When installing a KM 402 /

KM 403 or KM 410 / KM 411 remember

to allow clearance for the drain valve

that will be located in the cabinet

beneath the appliances.

The following safety distances must be

maintained:

–Between the cooktop and rear wall:

2" (50 mm).

–Between the cooktop and side wall

or cabinet:

KM 400 = 2" (50 mm)

KM 402 / 403= 2" (50 mm)

KM 408-1 = 2" (50 mm)

KM 410 / 411 =10" (250 mm)

Refer to section "Important Safety

Instructions" for further information.

Installing one or multiple appliances:

Cut out the countertop using the

dimensions listed in the following table.

Number of

cooktops

Cut out width

Dimension "B"

110 13/16" (274 mm)

222 1/8" (562 mm)

333 7/16" (850 mm)

444 13/16 (1138 mm)

556 1/8" (1426 mm)

667 1/2" (1714 mm)

778 13/16" (2002 mm)

The tolerance for each dimension is

1/16" (1 mm).

When installing more than one

combiset cooktop, a support bar

must be installed between the

appliances. Install the support bars

as shown on the following page

before setting the appliances into

the countertop.

Installation

9

Laying out the support bars

and clamps

aClamps

bSupport bars

This illustration shows the layout for 3

combisets, their respective support

bars, b, and the 14 spring clamps, a,

required for correct installation.

If more than 3 combisets are being

installed, add an additional 11 3/8"

(288 mm) to the overall width of the cut

out for each extra combiset, or use the

table on the preceding page.

cSlight gap between support bar and

countertop.

Installation

10

Securing the support bars

Wood or Corian countertops

^Arrange the bars, b, as shown in the

illustration

^Drill 1/16" (1.5 mm) pilot holes through

the brackets and secure them using

the supplied screws.

^Fill the gap, c, between the bars and

the countertop using the supplied

silicon sealant.

Granite countertops

For granite countertops, the support

bars, b, can be secured using

double-sided construction tape. Do not

allow the bars to "float", they must be

securely fastened. Fill the gap, c,

between the bars and the countertop

using the supplied silicon sealant.

The screws are not necessary for

granite countertops.

Securing the spring clamps

Wood or Corian countertops

^Place the spring clamps, a, as

shown in the illustration.

^Drill two 1/16" (1.5 mm) pilot holes for

each clamp and secure using the

supplied screws.

Granite countertops

For granite countertops, the spring

clamps can be secured using

double-sided construction adhesive.

Do not allow the spring clamps to

"float", they must be securely fastened.

The screws are not necessary for

granite countertops.

Installation

11

c

d

Locking the appliance into

place

Make sure the cooktops are aligned

correctly before setting them into the

countertop. Once the spring clamps

are engaged, a special tool is

required to release the cooktop from

the clamps.

^Guide the power cord through the cut

out and connect the appliance to the

electrical supply.

^Position the cooktop over the cut out.

With a hand on each side, above the

clamps, a, press the cooktop down,

locking it into the spring clamps.

Make sure that the cooktop rim lies

flat against the countertop on all

sides.

Installation

12

Important The cooktop must not be

permanently sealed into the

countertop when installed.

The sealing strip under the edge of

the cooktop provides a sufficient

seal for the countertop.

If the cooktop is sealed into position,

the countertop or the appliance may be

damaged if the cooktop needs to be

removed for maintenance or service.

Installation

13

,WARNING:

Disconnect the appliance from the

main power supply before servicing.

To reduce the risk of electric shock,

make sure that the appliance is

properly grounded after installation.

To guarantee the electrical safety of

this appliance; continuity must exist

between the appliance and an

effective grounding system. It is

imperative that this basic safety

requirement be met. If there is any

doubt, have the electrical system of

the house checked by a qualified

electrician. The manufacturer cannot

be held responsible for damages

caused by the lack, or inadequacy

of an, effective grounding system.

All electrical work should be

performed by a qualified electrician

in accordance with local codes and

the:

- National Electrical code

ANSI / NFPA No. 70-1481

for USA

or

- Canadian Electrical Code Part I

(CSA Standard C 22.1)

for Canada

Note to the installer:

Please leave these instructions with the

consumer.

Power supply:

–240 V, 60 Hz, 15 A fuse rating

or

–208 V, 60 Hz, 15 A fuse rating

The oven is equipped with a power

cord consisting of 3 leads. They must

be connected to a dedicated line

through the use of an approved

junction box

Black : connect to L1 (hot)

Red: connect to L2 (hot)

Green: connect to GND (ground):

For further information, see the

wiring diagram provided with the

appliance.

WARNING:

THIS APPLIANCE MUST BE

GROUNDED

Electrical connection

14

15

Alterations rights reserved / 0705 M.-Nr. 05 060 863 / 01

en-US