Miele Pw 5065 Users Manual G

PW 5065 to the manual 823f7cfa-2066-4a11-b5ce-892ad425a87d

2015-01-24

: Miele Miele-Pw-5065-Users-Manual-222785 miele-pw-5065-users-manual-222785 miele pdf

Open the PDF directly: View PDF .
Page Count: 64

Download
Open PDF In Browser	View PDF

Operating manual
Washer
PW 5065

To prevent accidents
and machine damage
read these instructions
before
installation or use.

UV
M.-Nr. 06 787 080

Contents
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Guide to the washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using the washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Canceling a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Changing a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adding/removing laundry during a wash program . . . . . . . . . . . . . . . . . . . . . . . . 15
Program guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Program sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Selecting a spin speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Delay Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the inlet hose filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Opening the door during a power failure or when the drain is blocked . . . . . . . . 35
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Removing the shipping struts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Installing the shipping struts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Leveling the washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation on a base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Help to protect the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Settings J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Suds cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Menu Settings - Supervisor level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

IMPORTANT SAFETY INSTRUCTIONS
Read the operating instructions
before using this machine for the
first time. They contain important
information about the safety, use and
maintenance of the machine. Doing
so will prevent injury and damage to
the dryer.
Save these instructions and pass
them on to any future user.

WARNING - To reduce the risk
of fire, electric shock or injury:
Technical Safety
Check the packaging, the washer
and accessories for any signs of
damage. Do not use a damaged
appliance.
Before connecting the machine,
ensure that the connection data on
the data plate (circuit protection,
voltage and frequency) match the
mains electrical supply. If in doubt
contact an electrician.
The appliance must be grounded.
It is imperative that this basic
safety requirement be met.

Do not connect the appliance to
the mains electrical supply with an
extension cord. Extension cords do not
guarantee the required safety of the
appliance (e.g. danger of overheating).
The machine is built in accordance
with current safety requirements.
Incorrectly repaired machines may
pose a considerable risk to the user
which is not covered by the
manufacturer. Repairs should only be
performed by a Miele approved
technician.
Ensure power is not supplied to the
appliance while maintenance or
repair work is being performed. The
machine is only completely isolated
from the electrical supply when it is
turned off at the main switch and the
plug is pulled or by tripping the circuit
breaker.
Connect the washer, to the water
mains. Do not use old hoses.
Inspect the intake hoses regularly for
damage. They should be replaced as
needed to prevent water damage.
Faulty components must only be
replaced with genuine Miele spare
parts to maintain safety standards.
If the power cord is damaged it
must only be replaced by a Miele
Service technician with a genuine Miele
power cord.

IMPORTANT SAFETY INSTRUCTIONS
Use
Only use the washing machine to
wash items which are specified by
the manufacturer to be machine
washable on the fabric care label. Any
other applications may cause
undesirable results. The manufacturer
cannot be held responsible for damage
caused by improper use of the
appliance.
This appliance is not designed for
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
Do not install this machine in rooms
where temperatures below freezing
may occur. Frozen hoses may burst
under pressure. The reliability of the
electronic control unit may be impaired
at temperatures below freezing.

Do not wash articles that have
been previously cleaned, washed
soaked or spotted with gasoline,
organic substances dry-cleaning
solvents, or any other flammable
substances. These articles give off
vapors that could ignite or explode. Do
not add these items to the washload.
Before using the machine for the
first time, check that the shipping
struts at the rear of the machine have
been removed (see "Installation"). If the
shipping struts are still in place during
spinning, damage may result to both
the machine and adjacent furniture or
appliances.
Turn off the water supply if the
machine is to be left for any length
of time (e.g. vacation).
Overflow hazard!
Check that the drain can
accommodate the water flow before
operating the washer.
Make certain the drain hose is secured
in the drain, otherwise the force of the
expelled water could cause the drain
hose to come out of the drain.
Be sure that foreign objects (e.g.
nails, pins, coins, paper clips) do
not find their way into the machine.
These items may damage the
machine, which may also cause
damage to the laundry.

IMPORTANT SAFETY INSTRUCTIONS
If the correct amount of detergent
is dispensed, the machine should
not need to be descaled. If the washer
needs to be descaled, use a descaling
agent with corrosion protection. These
special descaling agents can be
purchased from the Miele Service
department. Use as directed.

The stainless steel casing must not
come in contact with liquid
cleaning or disinfection agents
containing chlorine. They may cause
corrosion. Do not store open
containers of this agent next to the
machine.

Never use solvent based cleaning
agents in this machine, this may
result in damage and create toxic
fumes. They will present a fire and
explosion hazard.

Children

Items which have been pre-treated
in solvent based cleaning agents
must be thoroughly rinsed in clean
water before being washed in the
machine.
Only use dyes specified by the
manufacturer as being suitable for
use in a washing machine. Use as
directed by the manufacturer.

Close supervision is necessary
when the appliance is used near
children. Do not allow children to play
on or in the appliance.

Using accessories
Accessories must only be installed
once approved by Miele. Installing
unapproved parts may void the
warranty and product liability.

Dye removers may contain sulphur
compounds which cause damage
such as corrosion. Do not use dye
removers in this machine.
The drum door glass will be hot
when washing at very high
temperatures. Do not touch the glass.
Danger of burns!

Guide to the washer
Control panel

a "Start" button, with indicator
starts the selected wash program.
b Display with –, "OK" and + buttons
allows more info to be seen on the
following screens.
c m Delay Start button, with indicator
d PC Indicator/Optical interface
allows a service technician to check
and update the wash programs

e Pre-wash button, with indicator
f Program selector
to select a wash program.
The program selector can be turned
clockwise or counterclockwise.
g "Door" button
to open the drum door.

Guide to the washer
Display

Temperature conversions
Celsius

Fahrenheit

95°C

203°F

75°C

167°F

60°C

140°F

40°C

104°F

30°C

86°F

– / + buttons
To change the component highlighted
in the display.
– decreases the value or moves the
marker up
+ increases the value or moves the
marker down.
"OK" button
To confirm the selected value and to
select the next component.
When selecting a program:
– the special programs,
– the final spin speed,
– the temperature of some programs,
and
– the delay start
are shown in the display.
The display also shows the running
time of the wash program and the
current time of day.
Additionally the menu "Settings J" can
be accessed by the display.

Before using for the first time
Setting time of day
The appliance must be correctly
installed and connected before the
first use. Please see the "Installation
instructions".
For safety reasons, it is not possible
to run a spin cycle before the first
use.

The Welcome screen shows when the
machine is turned on for the first time.

M
PROFESSIONAL
Welcome

The welcome screen will not show
anymore, once the total wash time of
the machine exceeds one hour.
Reminder of the shipping struts
The shipping struts must be
removed before using the machine
for the first time to avoid damage.
^ Confirm that the shipping struts have
been removed by pressing OK.

12:00
Set the time of day

^ Set the hours with the +/– buttons
and confirm with OK.
^ Repeat to set the minutes and
confirm.
The display shows the main menu.
First wash
The washer is ready for the first use.
A program must be run without
laundry and detergent to flush out any
residual water from the factory testing
process, as well as to activate the spin
cycle.
^ Turn the program selector to "Cottons
60°C" (140°F).
^ Open the water mains.
^ Press the "Start" button.
Once the program ends the washer can
be used for laundry.

Using the washer
1. Sort the laundry

General tips
– Dark fabrics often bleed the first few
times they are washed. They should
be washed separately several times
before being included in a mixed
load.
– Remove any lead weights or strips
from curtains before washing.
– Loose underwires should be
removed or sewn in place before
washing.
– Woolens and knitted garments
should be turned inside out.

^ Empty all pockets.

,Foreign objects left in pockets
(e.g. nails, coins, paper clips, etc.)
can cause damage to clothes and
the machine.
^ Pre-treat stains.

– Close zippers and hooks and eyes
before washing.
– Comforter covers and pillowcases
should be fastened in order to
prevent small items from getting
trapped inside of them.
Do not machine wash items if it is not
recommended on the fabric care label.

Tough stains (blood, egg, coffee, tea
etc.) or badly soiled areas (collars and
cuffs) should be penetrated with a stain
remover or a paste made from powder
detergent and warm water. Dab stains
with a damp light colored cloth. Do not
rub!

,Do not use chemical solvents in
the machine.
^ Sort the laundry.

Using the washer
2. Load the laundry

^ Close the drum door.

^ Open the drum door using the "Door"
button.
The drum light switches on.
^ Load the laundry loosely into the
drum.
For best results, wash mixed loads of
small and large items. This will improve
washing effectiveness and help
distribute the load evenly.
Note: Overloading the washer will
affect wash results and cause wrinkling.
To prevent damage to the door seal
and clothing, make sure that there is
nothing caught between the drum
door and the seal.

Using the washer
3. Select a program

When selecting "Special programs" the
display shows the list.
C

Quick wash

Shirts
Starch

^ Select the desired program with the
buttons +/– and confirm with OK.
The display switches to the program
selection.
Shirts

^ Select a program and the desired
temperature with the program
selector.
The display shows the selected wash
program.

Cottons

Duration:

600 rpm

0:37 h

^ To change the highlighted
temperature use the +/– buttons.
Confirm with "OK". The display then
switches to the spin speed.
Pre-wash

The display switches to the program
selection.
60°C

40°C

1400 rpm

0:47 h

^ To change the highlighted spin
speed use the +/– buttons. Confirm
with "OK".

^ Select a Pre-wash for heavily soiled
laundry.
If the additional function "Pre-wash"
cannot be selected, it is not available
for this wash program.
Delay Start
^ Select a delayed start if desired. See
"Delay Start".

The temperature can also be changed
in some programs.
^ Hold down the "OK" button until the
temperature is highlighted.
^ Adjust the temperature with the +/buttons.
11

Using the washer
4. Adding detergent
Use detergent according to the laundry
soiling and water hardness.
Too little detergent may cause:
– ineffective cleaning of laundry;
fabrics may become gray and stiff
over time.
– grease stains on the laundry.
– hard water deposits on the heating
element.
Too much detergent may cause:
– oversudsing with minimal drum
movement; poor wash, rinse and
spin results.
– higher environmental burden.
See "Detergent" for more information.

^ Pull out the detergent dispenser
drawer and add detergent.
j = Detergent for the main wash
i = Only add detergent (1/4 of the
total recommended amount of
detergent) to this compartment
for the pre-wash.
§

= Fabric softener or liquid starch.

^ Close the detergent dispenser
drawer.

Using the washer
5. Starting a program
Coin mechanism
If the machine is coin operated, please
regard the displayed request to pay.
If the door is opened after a program
has started or if the program is
canceled the credit is lost.

6. At the end of a program
The anti-crease program starts when
the laundry is not immediately removed
from the washer after the program
ends. "Anti-crease" and "End" will flash
alternately in the display.
^ Press the "Door" button to open the
drum door.
^ Remove the laundry.

"Start" flashes when a program can be
started.
^ Press the "Start" button.
The "Start" button indicator lights.
The drum light turns off after the
program starts.
The display shows the likely program
duration unless delay start was
selected. It will count down in minutes.
The first 10 minutes the washer
calculates the water absorbency of the
laundry. The overall program time may
be shortened or lengthened.
Additionally the sequence cycle is
displayed. The washer shows the
current program step.

^ Check the folds of the door seal for
any small articles which may have
been trapped.
Check the drum for any missed
pieces of laundry. Items
inadvertently left in the washer may
get damaged (e.g. shrink or
discolor) during the next wash cycle.
^ Turn the program selector to "Finish".
^ Close the drum door.

Using the washer
Changing a program
The program will be locked
3 minutes after the program has
started when the washer is operated
with a coin mechanism. Canceling
or changing a program is no longer
possible.

Canceling a program
A program can be canceled any time
after a program has started.
^ Turn the program selector to "End".
The washer drains the wash water away
and the program is canceled.
^ Press the "Door" button.
^ Remove the laundry.
or
^ Close the door and start a new
program.

To change a program
A program change is not possible after
a program has started.
To select a different program, the
started program must be canceled.
Adjusting the temperature
Some programs allow you to change
the temperatures up to 5 minutes after
the start.
^ Press OK.
The temperature is highlighted.
^ To change the highlighted
temperature use the +/– buttons.
Confirm with "OK".
Adjusting the spin speed
^ Press OK until the spin speed is
highlighted. Adjust the spin speed
with the +/– buttons. Adjustment is
possible until the start of the final
spin.
Selection of the "Pre-wash" is not
possible after the program has started.

Using the washer
Adding/removing laundry
during a wash program

The drum door cannot be opened if:
– the water temperature is greater than
130°F (55°C).

You can interrupt some programs to
add or remove a piece of laundry.

– the water level is too high.

^ Press the "Door" button to open the
door.

– the program has reached the "Final
Spin".

^ Add or remove the piece of laundry.

– the program is locked because the
washer is operated with a coin
mechanism.

^ Close the drum door.
The program will continue
automatically.
Note
Once the program has started the
washer cannot make adjustments to the
load size.
After adding or removing laundry, the
washer will default to the water and
electrical consumption of a full load.
The program running time may be
lengthened.

Program guide
COTTONS 95° to 30°C (203°F to 86°F)

ABCD

Items

Items of cottons, linens or mixed fabrics.

Tips

– Use COTTONS 95°C to sanitize laundry or for heavily soiled
items.
– Wash dark colored fabrics with detergent for colors or a
liquid detergent.

Detergent

Universal or color detergent

Load size

14.3 lb (6.5 kg)

MINIMUM IRON 60°C to 30°C (140°F to 86°F)
Items

Synthetics, mixed fabrics or wrinkle free cottons.

Detergent

Universal or color detergent

Load size

7.7 lb (3.5 kg)

DELICATES 40°C to cold (104°C to cold)
Items

Delicates made from synthetics, mixed fabrics or silk

Tip

Wash items containing wool in the woolens program

Detergent

Detergent for delicates

Load size

5.5 lb (2.5 kg)

GHJ

Towelling 60°C to 40°C (140°F to 104°F)
Tip

Use color detergent for dark colored laundry

Detergent

Universal detergent

Load size

12 lb (5.5 kg)

Table linen 75°C to 60°C (167°F to 140°C)
Items

Table cloths and napkins made of cottons, linens or mixed
fabrics.

Tip

Use the "Pre-wash" program for tough stains. Use a Pre-wash
detergent with enzymes.

Detergent

Universal detergent

Load size

14.3 lb (6.5 kg)

Program guide
Bed linen 60°C to 40°C (140°F to 104°F)
Items
Tip
Detergent
Load size

Bed linens made of cottons or mixed fabrics.
Use color detergent for color items
Universal or color detergent
14.3 lb (6.5 kg)

Curtains 40°C to cold (104°C to cold)
Items
Curtains which are machine washable according to the
manufacturer.
Tip
For curtains which tend to wrinkle select "Without spin".
Detergent
Load size

Universal and color detergent in powder form.
6.6 lb (3.0 kg)

Denim 40°C to cold (104°C to cold)
Tips
– Before washing denim items turn them inside out to prevent
wear and fading.
– Denim items bleed after the first few washes. Wash dark and
light colored items separately.
Detergent
Load size

Liquid color detergent
7.7 lb (3.5 kg)

Dark garments 40°C to cold (104°C to cold)
Items
Tip

Dark items made of cottons or mixed fabrics.
Wash items inside out.

Detergent

Liquid color detergent

Load size

6.6 lb (3.0 kg)

WOOLENS

30°C to cold (86°F to cold)

Items
Detergent
Load size

Items made from washable wool and mixed woolens.
Detergent for wool
5.5 lb (2.5 kg)

Drain/Spin
Tip

Load size

Drain only: Select "Without spin".
When spinning be sure to select an appropriate speed for the
fabric type.
14.3 lb (6.5 kg)

Program guide
Special programs
Quick wash 40°C (104°F)

Items

Small load of lightly soiled items, which can be washed in
"COTTONS"

Detergent

Universal or color detergent

Load size

7.7 lb (3.5 kg)

Shirts 60°C to 40°C (140°F to 104°F)
Items

Shirts and dress shirts.

Tip

Pre-treat collars and cuffs if they are more soiled than usual.

Detergent

Universal or color detergent

Load size

5.5 lb (2.5 kg)

Starch
Tip

The laundry (table cloths, napkins, etc.) should be washed but
not treated with fabric softener.

Starch

Liquid starch or powder starch

Load size

14.3 lb (6.5 kg)

Pillows 95°C to 40°C (203°F to 104°F)
Items

Washable pillows with a filling of feathers, down or synthetics.

Tips

Follow the information on the fabric care label.

Detergent

Use liquid detergent.

Load size

1 queen or 2 twin size pillows

Outerwear 40°C to cold (104°C to cold)
Items

Outdoor clothing made of micro fiber.

Tips

– Close all zippers.
– Do not use fabric softener.

Detergent

Use liquid detergent.

Load size

6.6 lb (3.0 kg)

Program guide
Proofing 40°C to 30°C (104°F to 86°F)
Items

To treat micro fiber, ski clothing, fine dense cotton or table cloths
to make them water repellent and soil resistant.

Tip

– The item should be washed and spun or dried.
– To get an optimum result heat-treat the items in a clothes dryer
or by ironing them.

Water
repellent

– Only use a water repellent that is "Suitable for membrane
textiles". They are based on fluorochemicals.
Do not use agents containing paraffin.
– Place the liquid detergent insert in compartment j and fill with
water repellent.

Load size

6.6 lb (3.0 kg)

Extra Rinse
Items

For items only to be rinsed and spun.

Load size

14.3 lb (6.5 kg)

Program guide
Additional special programs can be accessed in the menu "Settings Supervisor level". Contact Miele technical service to access these programs.
Intensive Wash 60°C to 40°C (140°F to 104°F)
Items
Heavily soiled cottons, linen or mixed fabrics
Detergent
Load size

Universal or color detergent
14.3 lb (6.5 kg)

Flour 95°C to 40°C (203°F to 104°F)
Items
Jackets, hats, rags made of cotton or mixed fabrics
Tips

Detergent
Load size

– An additional pre-rinse is added to the program automatically.
– Use a Pre-wash detergent with enzymes.
– Use the "Flour +" program for heavy soiling.
Universal detergent
14.3 lb (6.5 kg)

Grease and fat 95°C to 40°C (203°F to 104°F)
Items
Jackets, hats, rags made of cotton or mixed fabrics
Tips

– Use a Pre-wash detergent with enzymes.
– Use "Grease and fat +" for heavy soiling.

Detergent
Load size

Universal detergent
14.3 lb (6.5 kg)

Towels short 40°C (104°F)
Items
Tip
Detergent

Lightly soiled cotton terry laundry
Use color detergent for dark colored laundry.
Universal detergent

Load size

12 lb (5.5 kg)

Program guide
Towels + 60°C to 40°C (140°F to 104°F)
Items
Tip
Detergent
Load size

Lightly soiled cotton terry laundry
Use color detergent for dark colored laundry
Universal detergent
12 lb (5.5 kg)

Capes 30°C (86°F)
Items
Lightly soiled synthetic capes
Detergent
Load size

Detergent for delicates
6.6 lb (3.0 kg)

Chem. Therm. Dis. 20 min 60°C (140°F)
Items
(Chemothermal Disinfection) Work clothes or disinfection
laundry, sorted by colors, which is suitable for disinfection.
Detergent
Disinfection detergent
Load size

14.3 lb (6.5 kg)

Hygiene
If a temperature lower than 131°F (55°C) was selected for the last wash program
or if the program "Drain/Spin" was selected, "Hygiene" is displayed. This ensures
that no bacteria is carried over from one laundry cycle to the next.
To select a Hygiene program:
– do not put any laundry into the drum, add a small amount of detergent in
compartment j and start the program,
or
– select a wash program with a temperature of 60°C or higher.
If neither of the above suggestions are carried out the program will run normally.

Program sequence
Main wash

Rinse

Spin

Water
level

Wash
rhythm

Water
level

Rinses

Rinse
spin

Final
spin

COTTONS

(

MINIMUM IRON

(

DELICATES

–

Towelling

(

Table linen

(

Bed linen

(

Curtains 1)

(

–

Denim

(

–

Dark garments

(

Woollens

(

Quick wash

(

Shirts

(

–

(

–

(

–

(

Proofing

–

(

Extra Rinse

–

Intensive wash*

(

Flour*

(

2-3

Grease and fat*

(

Towels*

(

Capes*

(

–

Chem.Therm. Dis.*

(

Starch
Pillows

Outerwear

* = Programs can be added from the "Settings - Supervisor level" when activated
by the Technical Service.
See the following page for explanations of symbols and special features.

Program sequence
Symbols
d = Low water level
( = Medium water level
e = High water level
a = Normal wash rhythm
b = Gentle wash cycle
c = Woolens

The washer is equipped with an
electronic control which determines the
load size automatically. The washer
determines the required water
consumption for each load and water
absorbency of the laundry. Different
program sequences and wash times
will result.
The program sequence shown in the
chart represents the basic program with
a maximum load. Possible "Options" are
not considered.
The washer’s program sequence
display will indicate the current step of
the selected wash program.

Special features in the program
sequence:
Anti-crease:
The drum continues to turn up to 30
minutes after the program has ended to
prevent wrinkling. The washer can be
opened at any time. Exception: The
program "WOOLLENS" has no
anti-crease feature.
1)

Pre-rinse
To rinse excess soiling, a pre-rinse
without detergent is automatically
added to the program.

High Spin
Before the wash program starts, a
high spin is carried out to remove the
air from the pillows. After the spin the
program starts with the water intake.

In the "Outerwear" program the items
will be spun only after the main
wash.

In the program "Flour +" a third rinse
is added.

Selecting a spin speed
Program

max. rpm

COTTONS

1400

MINIMUM IRON

1000

DELICATES

600

Towelling

1400

Table linen

1200

Bed linen

1200

Curtains

400

Rinse spin
The laundry is spun after the main wash
and between the rinse cycles.
Reducing the final spin speed will also
reduce the rinse spin speeds.
To omit the final spin (Rinse hold)
^ Select "Rinse hold". The laundry is not
spun and remains soaking in water.
This will prevent wrinkles if the
laundry is not removed immediately
at the end of the wash program.

Denim

900

Dark garments

1200

WOOLLENS

1200

Drain/Spin

1400

Quick wash

1200

Shirts

600

Starch

1200

If the laundry consists of a mixed load,
articles which do not require spinning
can be removed at this time.

Pillows

1400

– Starting a final spin

Outerwear

900

Proofing

800

^ Select a final spin speed with +.
The final spin starts.

Extra Rinse

1200

Intensive wash*

1400

Flour*

1400

Flour +*

1400

– To finish the program
^ Press – or "Door". The water will
drain.

Grease and fat*

1400

Grease and fat +*

1400

Towels short*

1400

Towels +*

1400

To omit rinse spin and final spin

Capes*

600

^ Select "Without spin".

Chem. Therm. Dis. 20 min*

1400

* = Programs can be added from the "Settings Supervisor level" when activated by Technical
Service.

The final spin speed can be reduced.
The speeds shown above are the
highest available.

^ Press the "Door" button to open the
door.

The laundry is not spun after the final
rinse but the water is drained away.
After the drain cycle the washer goes
immediately into the anti-crease cycle.

Delay Start
Starting the delay start
The delay start feature cannot be
used when the washer is operated
by a coin mechanism.
The delay start feature allows you to
start a program at a later time. The
program start can be delayed 30
minutes up to 24 hours.
The time of day must be correctly
set to allow the delay start feature to
function properly.

Start in:

1200 rpm

2:41 h

The display shows in how many hours
and/or minutes the wash program will
start.
Changing the delay start

^ Correct the end time of the program
with the +/– buttons.

^ Press the m button.
7:51

^ Confirm with OK.
7:51
9:19

Finish:

40°C

^ Press the m button.

Setting the delay start

Start:

^ Press the "Start" button.

The display shows the current time of
day and the resulting end time.
^ Select the desired program end time
with +.
7:51

Canceling the delay start
^ Press the m button.
^ Change the program end time with
the – button until the program start
matches the current time of day.
^ Confirm with OK.
The program starts immediately.

Start:

10:32

Finish:

12:00

Pressing the button once delays the
program end to the next full or half hour.
Each touch after that delays it by
30 minutes.

After the program start the actual
load size is measured. This may
result in an earlier program end time.

The – button decreases the time.
^ Confirm with "OK".

Detergent
Only use laundry detergent formulated
for front loading washing machines.
For wool and wool blend fabrics use a
detergent formulated for wools.
Follow instructions on the detergent
packaging for the correct use and
amount of detergent.
The amount of detergent used
depends on the level of soiling:
Light soiling
No soiling or stains are visible.
Normal soiling
Some visible soiling or a few light
stains.
Heavy soiling
Very visible soiling or stains.
The size of the load and the water
hardness level in your area have an
impact on the amount of detergent
necessary to obtain optimum wash
results. If you do not know the water
hardness level in your area, contact
your local water authority.

Water hardness
Hardness
level

Water
quality

Water
Water
hardness in hardness
in mmol/l
gpg
(also German
hardness in
°d)

soft

0-7

0 - 1.3

moderate

7 - 14

1.3 - 2.5

III

hard to
very hard

over 14

over 2.5

Water softener
If the water hardness level is between II
and III, you can soften the water to
reduce detergent consumption.
The detergent packaging should
indicate the correct amount to use in
your machine. Add the detergent, then
add the water softener. From then on
you can then use the recommended
amount of detergent for water hardness
level I.

Detergent
Fabric softener, liquid starch

Separate fabric softener

Fabric softener added to the wash
program will make fabrics feel softer
and will reduce static cling in the dryer.

^ Add the fabric softener to
compartment §.

Liquid starch is a synthetic starch wash
used to give fabrics some stiffness.
Starch can be included in any wash
program as part of the final rinse.
Automatic dispensing of fabric
softener or liquid starch

^ Select the "Starch" program.
^ Press the "Start" button.
Separate powder starch
^ Dispense the amount of starch
recommended on the packaging.
^ Add starch to compartment i.
^ Select the "Starch" program.
^ Press the "Start" button.
Never mix fabric softener and starch
together in the fabric softener
compartment §. This will clog the
dispenser.

Dye removers / Fabric dyes
^ Add the fabric softener or liquid
starch to compartment §. Do not
exceed the Max. level mark.
The softener or liquid starch is automatically dispensed in the final rinse. At
the end of the program a small amount
of water will remain in the fabric
softener compartment §.
If you use starch frequently, clean the
dispenser compartment and especially
the siphon tube and conditioner
channel. See "Cleaning the detergent
drawer".

Do not use dye removers in this
washer.
^ When dying fabrics in the washer,
adhere to the manufacturer’s
instructions.
External dispensing
As an option the washer can be set up
to an external detergent dosage
system. A conversion kit is necessary
which can be purchased from Miele
Technical Service.

Cleaning and Care
,Before cleaning the appliance,
disconnect the power supply by
unplugging the unit or manually
tripping the circuit breaker.
,Do not use chemical solvents,
abrasive cleaners, glass or all
purpose cleaners. These can
damage plastic surfaces and other
parts.
Cleaning the washer
^ Clean the exterior of the washer with
a mild solution of non-abrasive
detergent or soap and water. Wipe
dry with a soft cloth.
^ Clean the drum with a stainless steel
cleaner specially formulated for use
in a washing machine.

^ Pull out the detergent drawer as far
as it will go. Press the red release
lever down and pull the drawer out of
the machine.
^ Clean the detergent drawer with
warm water.
^ Clean the siphon tube.

Cleaning the detergent drawer
Detergent residue should be cleaned
out regularly.

1. Remove the siphon tube from the
compartment § and rinse under warm
water. Clean the pipe on which the
siphon tube is attached.
2. Replace the siphon tube.
28

Cleaning and Care
Cleaning the inlet hose filter
The washer has two water inlet filters to
protect each inlet valve. Check and
clean these filters every 6 months. This
may have to be done more frequently
with some water supplies.
Cleaning the inlet hose filters
^ Turn off the water faucet.

Slowly turn on the faucet and check
for leaks. If water leaks, tighten the
hose connection.
Cleaning the filter in the inlet valve
^ Using pliers carefully loosen and
remove the plastic hose connector
from the inlet valve.

^ Unscrew the inlet hose from the valve
by turning the connector
counterclockwise using a wrench if
necessary.

^ Using needle nose pliers, remove the
plastic filter by pulling on the bar (see
illustration). Rinse under running
water and return. Replace the filter
and seal then reconnect the hose.
^ Remove the rubber seal, 1, from the
connector.
^ Using needle nose pliers, grasp the
plastic filter, 2, and pull it out of the
hose connector.

Both filters must be put back in
place after cleaning.

^ Clean the filter under running water
and carefully remove any large
particles.
^ Replace the filter and seal and
reconnect the hose.

Frequently asked questions
,Repairs to electrical appliances must only be carried out by a qualified and
trained person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held responsible for unauthorized work.
The following section will help you avoid placing a service call by identifying
issues you may encounter while operating the machine:

A wash program cannot be started
Issue
The display and the
program selector
remain dark.

Possible cause
The washer has no
power.

When selecting the
program
"Drain/Spin" the
program does not
start.
The display remains
off.

The instructions in
"Before using for the
first time" were not
followed.

Solution
Possible fault
– the washer is connected to
the electrical supply,
– the circuit breaker has
tripped.
Follow the instructions as
described in the "Before using
for the first time" chapter.

The machine has gone Press any button. The Standby
into "Standby" mode.
function will end.
The display shuts off to
save energy.

Frequently asked questions
The display shows a fault message
Display message
q

Drainage fault

Possible cause
– The drain is blocked.
– The drain hose is too
high.

Solution*
– Clean the drain filter and
the drain pump.
– The maximum drain
pump height is 3 ft (1 m).

Water intake
fault

The water intake/inlet is
blocked.

Possible fault
– the water valve is
closed.
– the inlet hose is kinked.
– the filters are blocked.

Drainage lighting
fault

The drum light is not
locked in position.

Check that the drum light is
correctly fitted.

Technical
fault

There is a fault.

Start the program again.
If the fault message
appears again call Miele’s
Technical Service
Department.

* To cancel an error message, press OK.

Frequently asked questions
General problems with the washer
Issue

Possible cause

Solution

The washer shakes during – The four feet are
– Level the machine (see
the spin cycle.
not resting evenly
Installation Instructions).
on the floor.
– The floor is not
– It is recommended that
the machine is installed
properly reinforced.
on a concrete base.
There are unusual sounds There is no fault. Lapping sounds at the beginning
coming from the drain
and end of the pump process are normal.
pump.
Large amounts of
detergent residue remain
in the dispenser drawer.

– The water pressure – Check and clean the
is too low.
filters in the water inlet
hoses.
– Water softening
– Clean the detergent
detergent additives
drawer. In the future add
tend to clump.
the detergent first and
then the water softener
to the compartment.

The fabric softener is not
completely dispensed or
too much water remains
in the § compartment.

The siphon tube is
either incorrectly
positioned or
clogged.

Clean the siphon tube, see
"Cleaning and care Cleaning the detergent
drawer".

The display shows a
foreign language.

A different language
was selected under
"Settings J".

Select the desired
language. The flag symbol
leads you to the setting.

Frequently asked questions
Poor wash results
Issue

Possible cause

Solution

The laundry does not
get clean with liquid
detergent.

Liquid detergents do
– Use powder bleach.
not contain bleaching
(Be sure this is suitable
agents. Fruit, coffee
according the fabric care
and tea stains may not
labels of the laundry.)
be removed.
– Fill compartment j with
powder bleach and use a
dispenser ball for the
liquid detergent.
– Never put liquid
detergent and bleach
together in the same
wash compartment.

Laundry has a gray
sticky residue.

– Not enough
detergent was used
to dissolve greasy
deposits in heavily
soiled laundry.
– The laundry was
soiled with grease
(oils, lotions).

– Add more detergent to
laundry with grease
stains or use a liquid
detergent.
– Run a 140°F program
with liquid detergent to
clean the washer before
using it for laundry again.

There is white detergent The powder detergent – After drying, remove
white residues with a
residue on dark laundry. was not completely
clothes brush.
dissolved because of
hard water. These
– In the future, use liquid
residues are difficult to
detergent.
remove.
Items with greasy
soiling are not clean
after a wash program.

– Add a Pre-wash to the program. Use liquid
detergent for the pre-wash.
– Use a powder detergent for the main wash.
Use detergent which is specially formulated for
heavily soiled work clothes. Contact the detergent
manufacturer for more information.

Frequently asked questions
The door will not open when the "Door" button is pressed
Issue

Solution

The washer has no power. Insert the plug into the outlet and check that the
circuit breaker has not tripped.
Power failure

To open the drum door, see "Frequently asked
questions - Opening the drum door during a power
failure...".

The door was not
properly closed.

Push the drum door on the locked side. Then press
the "Door" button.

There is still water in the
drum and the washer
cannot drain it away.

Clean the drain filter and the drain pump as
described in "Frequently asked questions Opening the drum door during a power failure...".

As a safeguard against scalding, the drum door cannot be opened if the wash
water temperature is over 130°F (55°C).

Frequently asked questions
Opening the door during a
power failure or when the drain
is blocked

,Disconnect the machine from the
power supply.
^ Open the detergent dispenser
drawer.

Machines with a drain pump
If the main drain hose is clogged, water
will be retained in the machine (max.
6.5 gal [30 l]).

,Caution: If laundry has been
washed at a high temperature, the
water draining out of the machine
will still be hot! Stop and allow it to
cool before proceeding.
^ Place a 2 quart capacity container
under the drain tube.

^ Remove the tool.

^ Turn the lint trap lid counterclockwise.
Do not remove it. About 2 quarts of
water will drain out of the hose.
If additional water remains in the
machine, tighten the lint trap lid and
empty the container. Repeat as
necessary.

^ Open the lint trap door.

Frequently asked questions
Once the flow of water stops:

Open the drum door

,Always make sure the drum is
stationary before reaching into the
drum to remove laundry. A moving
drum is extremely dangerous.

^ Remove the lint trap lid.

^ Insert a screwdriver into the notch,
beside the lint trap, pull it down. The
door will now open.

^ Remove any foreign objects or lint
from the filter.
^ Check that the impeller (in the back
of the chamber) rotates freely by
spinning it with your hand.
^ Return the lint trap lid and tighten into
place.
If the drain filter is not tightened
securely water will leak out when the
machine is used.
36

Frequently asked questions
Machines with a drain valve

Open the drum door

,Always make sure the drum is
stationary before reaching into the
drum to remove laundry. A moving
drum is extremely dangerous.

^ Press the lever for the emergency
drain down and hold until you hear
no more water running out.

^ Insert a screwdriver into the notch,
beside the lever, pull it down. The
door will now open.

Frequently asked questions
Changing the light bulb
The machine will not operate if the light
bulb is burnt out.
^ Disconnect the power supply to the
work area by unplugging the unit,
tripping the circuit breaker or
removing the fuse.
^ Open the detergent dispenser
drawer. Remove the tool from the rear
side of the panel.
^ Open the drum door.

^ Press together the hooks of the
plastic fitting, 2, to separate it from
the bulb,1.
^ Replace the bad light bulb with a
new one.
A replacement bulb can be obtained by
contacting Miele.
The light bulb must not exceed the
maximum wattage listed on the data
plate.
^ Insert the light bulb into the plastic
fitting.
^ Insert the drum lighting in the socket
and turn clockwise.

^ Insert the tool into the slit of the light
bulb, turn counterclockwise until
resistance is felt.
^ Pull out the drum lighting.

To use the washer it is absolutely
necessary to have the light bulb
properly installed.

After sales service
Repairs

PC Update

In the event of a fault which you cannot
fix yourself, please contact the Miele
Technical Service Department.

The indicator marked PC allows a
technician to make use of new
technology if new programs are
developed or new fabrics are
introduced.

1-800-999-1360
techserv@mieleusa.com

1 800 565-6435
service@miele.ca

When contacting the Technical Service
Department, please quote the model
and serial number of your appliance.
Both can be found on the data plate
visible above the front glass on the
inside of the door.

Optional accessories
Optional accessories are available at
your Miele dealer or Miele.

Installation Instructions

To prevent accidents
and machine damage
read these instructions
before
installation or use.

Installation
Front view

a Water intake hose hot
b Water intake hose cold
c Electrical connection
d Control panel
e Detergent dispenser drawer
f Drum door

g Access panel to drain filter, drain
pump and emergency door release
h Height adjustable feet
i Stand
j Retaining clips (for concrete stand)
k Recessed grip

Installation
Rear view

a Lid with transport grips

d Shipping struts with rotary protectors

b Mounting for:

e Water intake hose (cold)

– Water intake hose

f Water intake hose (hot)

– Drain hose

g Drain hose for drain pump

– Withdrawn shipping struts

h Drain hose for drain valve

c Power cord

i Height adjustable feet

Installation
Installation site
The washer cannot be built-in.

,Do not install the machine
directly next to or over an open floor
drain or drain channel. Moisture can
penetrate the machine and damage
electrical parts.
A concrete floor is the most suitable
surface for the washer. Concrete floors
are less prone to vibration during the
spin cycle than wooden floors.

,If the machine is installed on a
masonry or concrete base it must
be secured with retaining clips to
prevent the washer from vibrating off
the stand during the spin cycle.

Installation
^ Use the front washer feet and the rear
excess end to transport the washer
from its shipping pallet to the
installation site.
Do not lift the washer by the drum
door.

,Ensure that the machine’s feet
and the floor are dry to prevent
slippage during the spin cycle.

Removing the shipping struts
^ Remove the left and right rotary
protectors.

^ The machine must be leveled and
securely positioned.
^ To avoid vibration while spinning, the
machine should not be installed on
soft floor coverings.
In case the installation must be on a
wooden joist floor:
^ Install the unit on a 27 9/16" x 23 5/8" x
1 3/16" (70 x 60 x 3 cm) plywood
base. Ideally the base should be
large enough to span several joists
and should be anchored to the joists
and not just the floor boards.
It is best to install the washer in the
corner of a room, where the stability of
the floor is at its greatest.

1. Unhook the rotary protector with a
screw driver.
2. Remove the rotary protectors.

Installation

^ Turn the left shipping strut
counterclockwise 90° with the
enclosed combination wrench.

^ Turn the right shipping strut
counterclockwise 90° with the
enclosed combination wrench.

^ Pull the shipping strut out.

^ Pull out the shipping strut out.

Installation
,Movement of the washer without
the shipping struts in place should
be kept to a minimum. The shipping
struts should be stored on the back
of the washer for future use. They
must be reinstalled before moving
the machine.

Installing the shipping struts
^ Reinstall the struts by reversing the
installation procedure.
^ Close the holes with the rotary
protectors and their caps.

^ Fasten the shipping struts at the rear
side of the washer. Take care to insert
the drill holes, b, into the clamps, a.

Installation
Leveling the washer

Adjust the four leveling feet
The washer is leveled by adjusting the
four feet. The machine is boxed with the
feet completely screwed in.

To ensure smooth operation the washer
must be level.
Failure to level the machine can result
in increased water and energy
consumption as well as the washer
"banging" during the spin cycle or
"walking" across the floor during use.

^ Turn the locking nut, 2, counterclockwise with the enclosed
combination wrench. Unscrew each
of the four feet as much as necessary
by turning both the foot, 1, and the
locking nut, 2, to the left.
^ Check that the machine stands level.
^ Once level, hold the foot, 1, steady
with a wrench. Turn the locking nut, 2,
with the combination wrench towards
the machine.

,All four locking nuts must be
tight against the bottom of the
machine. In addition, check to see
that the feet were not inadvertently
unscrewed while tightening the nuts.
Running a machine that is not level
or whose feet are not tight may
cause damage to both the machine
and its surrounding area.

Installation
Washer/ Dryer Stack

Installation on a base
The machine can be installed on an
open or closed steel base, or on a
concrete base. Concrete is
recommended.
^ Secure the two front feet of the
washer with the supplied retaining
clips when installing on a concrete
base.
^ Read the supplied Installation
manual.

Coin mechanism
Height:
Stacking kit with pull out shelf
66 15/16" (1700 mm)
The Miele washing machine can be
installed as part of a washer-dryer
stack in combination with a Miele
tumble dryer. An appropriate stacking
kit* is required.
Installation of the stacking kit must be
performed by a Miele Service
Technician.

The dryer can be equipped with a coin
mechanism*.
The reprogramming necessary for the
coin mechanism must be done by a
Miele Service Technician.
Empty the coin mechanism regularly.
Coins or tokens may get jammed.

Do not install devices to automatically turn the washer off, e.g. a
clock timer.

Reinstallation of the machine lid
When reinstalling the appliance lid,
check the firm fit of the cover at the rear
bracket for a safe transport of the dryer.

* Available from your Miele dealer or
Miele.

Installation
Water connection

Maintenance

Cold water connection

Replace the water hoses only with
genuine Miele hoses.

A water faucet with 3/4" threat must be
provided on-site. If none is available the
machine must be connected to a water
line by a qualified plumber.

Extension hoses
Extension hoses (8’ 2" or 13’ [2.5 m or
4 m]) may be obtained from Miele.

The water pressure must be between
14.5 -145 psi (1 -10 bar). If the water
pressure is greater than 145 psi
(10 bar), a pressure reducer must be
installed. If the water pressure is below
15 psi (1 bar), there will not be enough
water available for a complete fill.
The cold water hose (blue mark) is
not suitable for a hot water
connection.
^ Connect the cold water intake hose
(blue mark) to the cold water valve.
^ Turn on the valve(s) and check for
leaks.
The water intake hoses are
equipped with screen filters. Do not
remove these filters except for
cleaning.

Installation
Hot water connection
Connecting the machine to a hot water
supply will lead to low electrical
consumption during hot water
operation. The hot water temperature at
the water faucet must not exceed 158°F
(70°C).
The water in single water lines from the
hot water source cools faster when not
in constant use. To heat the wash water
more electricity must be used. The
same conditions for the hot water as for
the cold water connection will then
apply.
^ Connect the hot water intake hose
(red mark) to the water faucet.
The connection of the machine to a
hot water line only, is not possible for
functional reasons.

If the washer is not to be installed for
hot water connection, the settings "Main
wash", "Pre-wash" and "Rinses" must be
adjusted respectively. The hot water
intake hose must be removed.
^ Select in "Settings - Supervisor level"
the respective options "cold".
The program times may be
extended.
^ Unscrew the hot water intake hose
(red mark).
^ Screw on the supplied stopper.

Installation
Drainage
There are two drainage options for this
machine:
Drain valve
The machine is drained with a
motorized drain valve. A connection
can be made to an on-site floor drain
(gully with an air gap) on an angle.

If necessary the drain hose can be
extended up to 16’ 5" (5 m). The hose
extension can be purchased from your
Miele dealer or Miele.
The drain pump must be replaced for
drain heights over 3 ft (1 m). The
maximum allowable drain height is 5 ft
11 in (1.8 m). A stronger pump for
these heights can be purchased from
your dealer or Miele.

Drain pump
The wash water is drained using a
pump with a 3 ft (1 m) delivery height.
Make sure there are no kinks in the
drain hose. The elbow on the end of the
drain hose can be turned or removed if
necessary.
Possible connections:
1. Directly into a sink: Hook the hose
over the edge of the sink and secure
it firmly (e.g. by tying the hose to the
water faucet).
2. To a stand pipe: Place the drain
hose into a 11/2" (4 cm) stand pipe
and secure it firmly.
3. To a floor drain: The machine is
equipped with an air gap/
anti-siphoning system so that no
minimum drain height is required.

Installation
Electrical connection

,This installation should be
performed by an experienced and
qualified technician, in accordance
with local codes and regulations.
The washer comes with a power cord
without a plug.
The machine is supplied as standard
for connection to a 208 V, 60 Hz, 20 A,
2-phase electrical supply*.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The machine must only be connected
to the voltage and frequency shown on
the data plate.

,*To convert the machine to
another electrical connection,
please read the converting manual
on the wiring diagram inside the
washer. The conversion must be
performed by a Miele Service
Technician. Additionally the "Heating
level" setting must be adjusted.
,Do not install devices to
automatically turn the washer off,
i.e. a clock timer.

If the machine is hard wired, two 20 A
circuit breakers must be provided
on-site. Switches with a contact gap of
more than 3 mm are valid as
separators. All components must be
CSA or UL approved.

Technical Data
Height

33 7/16" (85 cm)

Width

23 7/16" (59.5 cm)

Depth

28 3/8" (72 cm)

Depth with the door open

44 1/8" (112 cm)

Weight

236 lb (107 kg)

Maximum floor load

2778 Newton (approx. 278 kg)

Capacity

13.2 lbs (6.5 kg) dry laundry

Fuse rating

see data plate

Rated load

see data plate

Fuse rating

see data plate

Noise level during spinning
(Noise emission 3. GSGV)

< 70 dB(A)

Minimum water flow pressure

14.5 psi (1 bar)

Maximum water pressure

145 psi (10 bar)

Length of intake hose

5’3" (1.6 m)

Length of power cord

5’3" (1.6 m)

Drain height maximum (Drain pump)

3’3" (1 m)

Light bulb for drum light

Type G4 (5 Watts/12 Volt)

Help to protect the environment
Disposal of the packing
materials
The cardboard box and packing
materials protect the appliance during
shipping.
To prevent suffocation of children
ensure that any plastic wrapping, bags,
etc. are disposed of safely and kept out
of the reach of children.
Please recycle.

Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.

Menu Settings J
to adjust standard settings
The washer controls can be adjusted to changing demands through the settings
menu.

Settings J
Accessing the "Settings" J
^ Turn the program selector to "Finish".
The main menu shows.
12:03
Selecting a program
Settings F

^ Confirm with OK.
^ The "Settings" menu is selected.
C

BackA
Language F
Suds cooling

^ Set the desired setting with the
buttons +/– and confirm with OK.

Language J
The display contents can be shown
in different languages.
The displayed language can be
changed by the sub-menu
"Language J".
The flag behind the word "Language J"
is a guide to find the settings menu in
case a foreign language is selected.
The selected language is marked with a
check.
If the language setting was changed, it
is only valid for the current wash
program. Once the program ends, the
display will show the language which is
set under "Settings - Supervisor level".

Leaving the Settings menu
^ Select "Back" and confirm with OK.
The display shows the main menu.

Suds cooling
Cold water is added at the end of
the main wash to cool the wash
water.
The wash water cooling is carried out
when a wash temperature of 158°F
(70°C) or more is selected.
The wash water cooling should be
activated when the drain hose is hung
into a sink, to prevent scalding
The wash water cooling is factory set
"on".

Settings J
Time of day
This selection allows the clock to be
shown as 24 hours, 12 hours or not
at all. The time of day is also set
here.
If the clock is not selected the delay
start can only be shown as a 24 hour
timer. The display will show the timer
counting down until the start of the
program but not the current time of day.
Selecting the clock display
^ Select the desired clock display and
confirm.
The display shows the clock setting.
Set the time of day

Display contrast
The contrast of the display can be
set at ten different levels.
It is factory set to Setting 4.
The contrast changes immediately
when a different level is selected.

Display brightness
The brightness of the display can be
set at ten different levels.
It is factory set to Setting 5.
The brightness changes immediately
when a different level is selected.

^ Set the hours with the buttons +/–
and confirm with OK. Repeat with
setting the minutes and confirm. The
display changes to "Settings".

Settings J
Standby
The display goes out after 10
minutes and the "Start" button
flashes slowly to save energy.
Two options can be selected:
On
The display will go into standby mode:
– if no program is selected after the
machine is turned on.
– after a program has started.
– at the end of a program.
Not in current prog.
(factory default)
The Standby function will be turned on
if no program was selected after the
machine was turned on.
By turning the program selector or
pressing any button the display is
turned on again.

Memory
The Memory function remembers the
addition of an extra feature to a
program, a change in spin speed or
the temperature the next time that
program is selected.
Once the wash program is selected
again the washer shows the saved
options.
The Memory function is factory set to
"off".

Menu Settings - Supervisor level
The menu "Settings - Supervisor
level" has to be "activated" by a
Miele service technician or dealer.
The menu "Settings" (except
Language J) is locked with a code
to prevent unwanted access.
C

BackA

Language F

Entry OK.
Menu opened.

The user is now in the supervisor level.
The following settings can now be
changed.
Change the code to prevent
unwanted access to the settings.

Supervisor level

^ Select the "Supervisor level" and
confirm.
C

BackA

Enter code

^ Select the code and confirm.
Entering the code
A three digit code must be entered. On
delivery the code is: 0 0 0.

_ _

Enter code

^ Enter the first digit with the + button.
Confirm with OK.
^ Enter the second and third digit.
Confirm each with OK.

Menu Settings - Supervisor level
Language J
The display contents can be shown
in different languages.
The fixed language selection can be
set in the sub-menu "Languages J".
^ Select the desired language and
confirm with OK.

Pre-wash water
The water type (hot/cold) for the
pre-wash can be selected (except
for the program "Curtains"). The hot
water intake will be only accessible
at a wash temperature of 86°F
(30°C) or higher.
The machine comes factory set with
water type "hot".

Supervisor level
The access code for the operator
level can be changed.
^ Enter the old code.
^ Enter the new code.
Once the new code is confirmed, the
beginning of the "Settings" menu will
appear.

Main wash water
The water type for the main wash
can be selected (except for the
programs "WOOLLENS" and
"Curtains"). The hot water intake will
only be accessible at a wash
temperature of 86°F (30°C) or
higher.
The machine comes factory set with the
water type "hot" selected.

Auto load control
If the Auto load control is turned off
the program will run as if for a full
load.
The machine comes factory set with
this option "on".

If the washer is not connected to hot
water, the program running times will
be extended and vary from the
displayed remaining times.

Menu Settings - Supervisor level
Rinse water
The water type for the rinse cycle can
be selected for the "COTTONS" and
"MINIMUM IRON" programs. The hot
water intake will be only accessible at
a wash temperature of 122°F (50°C) or
higher.
The machine comes factory set with the
water type "hot" selected.

Temperature pre-wash
For the programs "COTTONS" and
"Grease and fat +" the pre-wash
temperature can be selected.
The machine comes factory set with the
option Block Parameter selected. (The
temperature will be controlled
according to the factory set program
data.)

Low Water Pressure
With generally low water pressure
(under 100 kPa) this option can be
activated to obtain better water intake.
The machine comes factory set with this
option "off".

COTTONS water level
The program "COTTONS" allows you
to increase the water level for the main
wash.
The machine comes factory set with the
option Block Parameter selected. (The
water level will be controlled according to
the factory set program data.)

MINIMUM IRON water level
The program "MINIMUM IRON" allows
you to increase the water level for the
main wash.

Pre-wash duration
The wash time for the pre-wash can
be extended.
The machine comes factory set with the
option Block Parameter selected. (The
wash time will be controlled according
to the factory set program data.)

COTTONS duration
The program "COTTONS" allows you
to extend the wash time for the main
wash.
The machine comes factory set with the
option Block Parameter selected. (The
wash time will be controlled according
to the factory set program data.)

The machine comes factory set with the
option Block Parameter selected. (The
water level will be controlled according to
the factory set program data.)
61

Menu Settings - Supervisor level
MINIMUM IRON duration
The program "MINIMUM IRON"
allows you to extend the wash time
for the main wash.
The machine comes factory set with the
option Block Parameter selected. (The
wash time will be controlled according
to the factory set program data.)

Hygiene
If a temperature lower than 140°F
(60°C) was selected for the last
wash program "Hygiene" is
displayed.
The machine comes factory set with
this option "off".

Pre-wash
Special programs list
Special programs can be added to
the program selection.
Option 1: The programs Quick wash,
Shirts, Starch, Pillows, Outerwear and
Proofing are shown. (Factory set)
Option 2: In addition to option 1
"Intensive wash" is offered.
Option 3: In addition to option 1 "Flour",
"Flour +" and "Grease and fat" are
offered.
Option 4: In addition to option 1
"Grease and fat" and "Grease and fat +"
are offered.
Option 5: In addition to option 1 "Towels
short", "Towels +" and "Capes" are
offered.
Option 6: In addition to option 1 "Chem.
Therm. Dis." (Chemothermal
Disinfection 20 minutes 60°C) is
offered.

For the programs "COTTONS" and
"MINIMUM IRON" pre-wash can be
permanently added.
If the pre-wash is permanently
selected, the indicator of the pre-wash
button lights.
The machine comes factory set with the
option "Menu selection" activated.

COTTONS rinses
The program "COTTONS" allows you
to change the number of rinses.
2 rinses (factory set)
3 rinses
4 rinses
5 rinses

Menu Settings - Supervisor level
MINIMUM IRON rinses
The program "MINIMUM IRON"
allows you to change the number of
rinses.
2 rinses (factory set)
3 rinses
4 rinses

External dosage
The washer is set for connection to
an external detergent dosage
system. To use the external dosage
system the setting must be
adjusted/set accordingly.
The machine comes factory set with
this option turned off.

Pre-rinse COTTONS
Leaving the Settings menu
The program "COTTONS" allows a
pre-rinse of the laundry.

^ Press "back" and confirm with OK.
The display shows the main menu.

The machine comes factory set with
this option turned off.

Pre-rinse MINIMUM IRON
The program "MINIMUM IRON"
allows a pre-rinse of the laundry.
The machine comes factory set with
this option turned off.

Spin - free of charge
When operated by a coin
mechanism, the program "Spin" can
be offered free of charge.
The machine comes factory set with
this option turned off.

Alteration rights reserved / 0806

M.-Nr. 06 787 080 / 01
en - USA

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2006:02:22 17:41:04Z
Modify Date                     : 2006:02:22 12:43:15-05:00
Page Count                      : 64
Creation Date                   : 2006:02:22 17:41:04Z
Mod Date                        : 2006:02:22 12:43:15-05:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : USAHOFS
Metadata Date                   : 2006:02:22 12:43:15-05:00
Creator                         : USAHOFS
Title                           : G:\Tech Writing\Data\Prof. Washer\us\vp\PW5065_us.vp
Page Mode                       : UseOutlines
Page Layout                     : SinglePage

EXIF Metadata provided by EXIF.tools

Miele Pw 5065 Users Manual G

PW 5065 to the manual 823f7cfa-2066-4a11-b5ce-892ad425a87d

Navigation menu

Versions of this User Manual:

Views

Navigation