Miele T 8822 C T8822C_gb.vp User Manual To The 5dfb06d0 0b74 4f19 87c4 C6f6a4639989

User Manual: Miele T 8822 C to the manual

Open the PDF directly: View PDF .
Page Count: 64

Contents

Operating instructions

for condenser tumble dryer

T 8822 C

To avoid the risk of accidents

or damage to the appliance

it is essential to read these

instructions before it is installed

and used for the first time. M.-Nr. 07 847 520

en-GB

Disposal of the packing

material

The transport and protective packing

has been selected from materials which

are environmentally friendly for disposal

and should be recycled.

Ensure that any plastic wrappings,

bags, etc are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation.

Disposal of your old appliance

Electrical and electronic appliances

often contain materials which, if

handled or disposed of incorrectly

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your appliance.

Please do not therefore dispose it with

your household waste.

Please dispose of it at your local

community waste recycling centre or

contact your dealer for advice. Ensure

that it presents no danger to children

while being stored for disposal.

Energy saving tips

To avoid unnecessarily long drying

times and high consumption of energy:

–Make sure that your laundry is

thoroughly spun before drying.

The higher the spin, the greater the

savings that can be made in energy

and time during drying.

–Load according to the optimum

amount of laundry recommended for

the programme being used (see Pro-

gramme chart).

Underloading is uneconomical.

Overloading gives a poorer quality of

drying and may cause unnecessary

creasing.

– Make sure the room in which the

dryer is located is well ventilated.

– Make sure the fluff filters are clean

before using the dryer.

– Check the condenser unit from time

to time and clean it when necessary.

Caring for the environment

Caring for the environment..........................................2

Warning and Safety instructions .....................................6

Operating the tumble dryer.........................................14

Control panel .....................................................14

Notes on laundry care .............................................16

Garment care label symbols .........................................16

Tips on drying ....................................................16

How to dry correctly ..............................................17

Brief instructions ..................................................17

Extra options / Delay start..........................................20

Extra options .....................................................20

Low temperature................................................20

Buzzer........................................................20

Delay start .......................................................20

Programme chart .................................................21

Changing the programme sequence .................................24

Once a programme has started ......................................24

- changing the programme........................................24

- cancelling the programme and then selecting a different programme .....24

- cancelling the programme and then removing the laundry ..............24

Altering Delay start ................................................24

Adding or removing laundry after a programme has started ................24

Time remaining ...................................................24

Electronic system lock ............................................25

Contents

Cleaning and care ................................................26

Emptying the condensed water container ..............................26

Cleaning the fluff filters .............................................27

Cleaning them whilst dry .........................................27

Cleaning them with water .........................................28

Cleaning the tumble dryer ...........................................29

Cleaning the condenser unit .........................................30

Removing the condenser unit......................................30

Checking the condenser unit ......................................31

Cleaning the condenser unit.......................................31

Replacing the condenser unit......................................32

Problem solving guide ............................................33

Check and fault messages ..........................................33

An unsatisfactory drying result .......................................36

Other problems ...................................................37

Changing the lamp ................................................39

After Sales service................................................40

Repairs..........................................................40

Future updates (PC) ...............................................40

Appliance guarantee ...............................................40

Optional accessories ...............................................40

Installation ......................................................41

Front view........................................................41

Rear view ........................................................42

Installation site ....................................................42

Transporting the dryer to its installation site ...........................42

Building under a continous worktop / in a kitchen run ...................42

Levelling the appliance...........................................43

Room ventilation ................................................43

Washer-dryer stack..............................................43

Before moving the tumble dryer again (e.g. when moving house) .........43

Contents

External condensed water outlet ......................................44

Arranging the drain hose .........................................44

External drainage via a sink or gully ................................45

Installation conditions requiring a non-return valve .....................45

Electrical connection .............................................47

Electrical connection U.K. ...........................................47

Consumption data ................................................48

Technical data ...................................................49

Programmable functions...........................................50

Altering the residual moisture level in the Cottons programme...............50

Altering the residual moisture level in the Minimum iron programme ..........51

Anti-crease ......................................................52

Altering the volume of the buzzer .....................................53

Altering the standard drying level in the Automatic plus programme ..........54

Extending the cooling down time .....................................55

Standby .........................................................56

Memory function ..................................................58

Clean out airways indicator ..........................................59

Keypad tone .....................................................60

Adjusting the dryer's electronics for very soft water .......................61

Extending the range of the drying levels ................................62

Contents

~It is essential to read these instructions.

This tumble dryer conforms to current safety requirements.

Inappropriate use can, however, lead to personal injury and

damage to property.

To avoid the risk of accidents and damage to the tumble dryer,

please read these instructions carefully before using it for the first

time. They contain important information on its safety, installation,

use and maintenance.

Keep these instructions in a safe place and ensure that new users

are familiar with the content. Pass them on to any future owner.

Correct application

~This tumble dryer is not designed for commercial use. It is

intended for use in domestic households and similar working and

residential environments.

~The tumble dryer is not intended for outdoor use.

~It must only be used as a domestic appliance to dry items which

have been washed in a water solution and which are marked on the

manufacturer's care label as being suitable for tumble drying. If

using dry cleaning kits, do so at your own risk, and follow the

instructions provided on the packaging.

Any other usage is not supported by the manufacturer and could be

dangerous. Miele cannot be held liable for damage resulting from

incorrect or improper use or operation.

Warning and Safety instructions

~The tumble dryer can only be used by people with reduced

physical, sensory or mental capabilities, or lack of experience or

knowledge, if they are are supervised whilst using it or have been

shown how to use it in a safe way and understand the hazards

involved.

Safety with children

~Children under 8 years of age must be kept away from the tumble

dryer unless they are constantly supervised.

~Children 8 years and older may only use, clean or maintain the

tumble dryer without supervision if they have been shown how to do

so in a safe way and understand the hazards involved.

~The tumble dryer is not a toy! To prevent the risk of injury, do not

allow children to play with it or near it, or to play with the controls.

Warning and Safety instructions

Technical safety

~Before setting up the tumble dryer, check it for any externally

visible damage.

Do not install or use a damaged tumble dryer.

~Before connecting the tumble dryer, ensure that the connection

data on the data plate (voltage and frequency) match the mains

electricity supply. If in any doubt, consult a qualified electrician.

~The electrical safety of this tumble dryer can only be guaranteed

when correctly earthed. It is most important that this basic safety

requirement is observed and regularly tested, and where there is

any doubt, the household wiring system should be inspected by a

qualified electrician. Miele cannot be held liable for the

consequences of an inadequate earthing system (e.g. electric

shock).

~Do not connect the tumble dryer to the mains electricity supply by

an extension lead. Extension leads do not guarantee the required

safety of the tumble dryer (e.g. danger of overheating).

~If the electrical connection cable is faulty it must only be replaced

by a Miele approved service technician to protect the user from

danger.

~Unauthorised repairs could result in unforeseen dangers for the

user, for which Miele cannot accept liability. Repairs should only be

undertaken by a Miele approved service technician, otherwise any

subsequent damage will not be covered by the guarantee. Ensure

current is not supplied to the tumble dryer until after maintenance or

repair work has been carried out.

Warning and Safety instructions

~Faulty components must only be replaced by genuine Miele origi-

nal spare parts. Only when these parts are fitted can the safety

standards of the tumble dryer be guaranteed.

~The tumble dryer must be isolated from the electricity supply in

the event of a fault and during cleaning and maintenance.

~The tumble dryer must not be used in a non-stationary location

(e.g. on a ship).

~Do not make any alterations to the tumble dryer, unless

authorised to do so by Miele.

~In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the tumble dryer

and its surroundings in a clean condition at all times. Any damage

which may be caused by cockroaches or other vermin will not be

covered by the guarantee.

Warning and Safety instructions

Correct use

~To prevent the risk of fire, the following textiles must not be dried

in this appliance:

–items which have not been washed.

–items, such as workwear, which have not been thoroughly

cleaned and which are still soiled with grease, oil or other

deposits (such as cosmetics, lotions etc).

If items have not been thoroughly cleaned there is a danger that

these might self-ignite when heated, even after they have been

removed from the dryer at the end of the programme.

– items (e.g. mops and floor cloths) which have been treated with

inflammable cleaning agents or which contain residues of

acetone, alcohol, benzine, petrol, kerosene, stain remover,

turpentine, wax and wax remover or other chemicals.

– items which have been splashed with hair lacquer, hair spray, nail

varnish remover or similar substances.

When washing such heavily soiled items, ensure that you use

additional detergent and select a high temperature. If in doubt,

wash the items several times.

~Remove all items such as lighters and matches from pockets.

~Warning: Do not switch the tumble dryer off before the drying

programme has finished. If this is done, the laundry must be hung

up or spread out to cool it down.

Warning and Safety instructions

~Danger.

This tumble dryer must not be connected to a controllable socket

(e.g. a timer switch or a peak load shut-off device).

If the dryer programme were to be interrupted before the end of the

cooling down phase, the laundry could self-combust.

~To prevent the risk of fire, the following must not be tumble dried:

–items which have been cleaned using chemicals (e.g.

professional dry-cleaning agents).

–fabrics which contain a large proportion of rubber, foam rubber or

rubber-like materials. For example, products made from latex

foam rubber, shower caps, waterproof textiles, rubberised articles

and items of clothing and pillows with foam rubber filling.

– damaged items which contain padding or fillings (e.g. pillows,

jackets). When damaged, the filling can get out with the risk of

igniting in the dryer.

~In many programmes, the heating phase is followed by a cooling

down phase to ensure that the items are not too hot to handle when

you remove them (this also avoids the danger of the laundry

self-igniting). The programme is not finished until the cooling down

phase has been completed.

As soon as the programme has finished, remove all laundry from the

drum.

~Fabric conditioner and similar products must be used according

to the instructions on the manufacturer's packaging.

~Do not let anyone sit or lean on the door, as this can cause the

tumble dryer to tip up.

~Always close the door after use. This way you will avoid the

danger of:

–children climbing into the dryer or hiding things in it.

–pets or other small animals climbing into it.

Warning and Safety instructions

~The dryer must not be used without the fluff filters in place or if

the fluff filters are damaged in any way.

~The fluff filters must be cleaned regularly.

~The dryer must not be used without the condenser unit in place.

~The fluff filters must be thoroughly dried after cleaning. Damp or

wet filters could cause operational faults.

~Do not install the tumble dryer in a room where there is a risk of

frost occurring. At temperatures around freezing point the tumble

dryer may not be able to operate properly. There is a risk of damage

if the condensed water is allowed to freeze in the pump and in the

drain hose. The ambient room temperature should be between +2°C

and +35°C.

~If the water is drained externally instead of being collected in the

condensed water container, make sure the drain hose is securely

attached if you hang it in a sink or basin to avoid the hose slipping

and the water causing damage.

~Condensed water is not drinking water.

It can cause health problems in both people and animals.

~Always keep the area around the tumble dryer free of dust and

fluff. Dust drawn into the tumble dryer can cause blockages in the

condenser unit over time.

~The tumble dryer must not be hosed down.

Warning and Safety instructions

Accessories

~Only use genuine Miele original spare parts and accessories with

this tumble dryer.

If non-Miele parts are used, guarantee, performance and product

liability claims may be invalidated.

Miele cannot be held liable for damage caused by

non-compliance with these Warning and Safety instructions.

Warning and Safety instructions

Control panel

aLow temperature button

Delicate fabrics are dried at a lower

temperature.

bDrying level button

with indicator lights to show the

drying level selected.

cDisplay

See next page.

dDelay start button

This button is used for:

- Delaying the start of a programme

- Selecting the duration of the timed

drying Warm air and Cool air

programmes

eBuzzer button

An audible tone sounds at the end of

the programme.

fPerfect Dry indicator

For all programmes with a selectable

drying level. See next page.

gCheck lights

For a description of these, see "Pro-

blem solving guide" / "After sales ser-

vice".

hStart/Stop button

For starting or cancelling a program-

me.

The button flashes while a program-

me is being selected and then lights

up constantly when the programme

has started.

iProgramme selector

with indicator lights to show the pro-

gramme selected.

jDoor button

Pressing this button will open the

door even when the dryer is

switched off at the mains.

kOn/Off button jk

For switching the dryer on and off.

Operating the tumble dryer

The display shows:

–Programme duration

–Programme stage

Drying

Cooling down

Finish

–Check and fault messages

The following are also selected via

the display:

–Duration of the Warm air and Cool air

programmes

– Delay start

You can select a programme and set

it to start at a later time.

The programme will start

automatically once the delay start

time has a elapsed.

– Programmable functions

Default settings can be altered to

adapt the dryer to different

requirements. See "Programmable

functions" at the end of this booklet

for more details.

Perfect Dry indicator

The Perfect Dry system measures the

residual content in the laundry in the

sensor drying programmes to ensure

perfect drying results.

After a programme has started, the

electronics will estimate the duration of

the programme (time remaining). The

Perfect Dry indicator will flash while this

is happening.

After a short while, the programme

duration will appear in the display and

the indicator will go out.

The Perfect Dry indicator will light up

again when the selected drying level is

reached and remain on until the pro-

gramme is finished.

The Perfect Dry indicator does not light

up during time controlled programmes:

Woollens handcare, Cool air, Warm air,

Gentle smoothing.

Programme duration /

Estimated time remaining

The estimated duration (time remaining)

will appear in the display.

The following factors all affect the

estimated time remaining: residual

moisture content after spinning; type of

fabric; size of load; room temperature;

fluctuations in power supply.

The electronics continually assess

conditions in the dryer and adjust the

estimated time remaining for a more

accurate reading. Because of this, the

time displayed can alter during the

course of a programme.

Programmes can also finish earlier than

expected, if, for example, particularly

fine fabrics are being dried, the load is

very small or items were partially dry

beforehand.

Operating the tumble dryer

Garment care label symbols

Drying

qNormal/higher temperature

rReduced temperature:

Select Low temperature

(for delicate textiles)

sDo not tumble dry

Ironing

IVery hot

HHot

GWarm

JDo not iron

Tips on drying

– Always observe the maximum

recommended loads given in the

"Programme chart". Never overload

the drum.

Overloading can cause unnecessary

wear and tear to the laundry, give a

disappointing drying result and

cause more creasing.

–Do not put soaking wet items into the

tumble dryer. Spin fabrics for at least

30 seconds before drying.

–Open jackets so that they can dry

evenly.

–Use the Automatic plus programme

for drying mixed loads of cotton and

minimum iron fabrics.

–Woollens and wool blends tend to

become matted and shrink if dried in

a tumble dryer. They can, however,

be "fluffed up" using the Woollens

handcare programme.

–Down-filled garments have linings

which have a tendency to shrink,

depending on the quality of the item.

They can be partially dried using the

Gentle smoothing programme.

–Pure linen should only be machine

dried if specified as suitable by the

manufacturer on the care label, as

the surface of the fabric may

otherwise become rough.

–Loopknit garments (e.g. T-shirts and

underwear) tend to shrink depending

on their quality. Do not over-dry

these textiles. When purchasing

these garments it is advisable to take

their shrinkage properties into

account.

– Minimum iron fabrics tend to crease

more, the larger the load. This is also

the case for garments made from

very fine weave fabrics, such as

shirts or blouses.

If in doubt, divide the garments into

smaller loads.

–Starched laundry can be dried in the

tumble dryer. To achieve the usual

finish, double the amount of starch

should be used.

–New dark coloured garments should

be washed and dried separately

from light coloured garments to avoid

the danger of colours running and

discolouring other garments or even

plastic components in the dryer.

Dark coloured fibres can also settle

on light coloured garments and vice

versa.

Notes on laundry care

Brief instructions

The headings numbered (A,B,C...)

show the operating sequence and can

be used as a brief guide to using your

dryer.

ASort the laundry

To ensure an even drying result sort

laundry according to:

. . . the drying level required

. . . the type of fibre or weave

. . . size

. . . the moisture content after spinning.

,Make sure that objects e.g.

detergent dispensing balls have

been removed from the laundry.

They could melt, and cause damage

to the dryer or the laundry.

– Check seams and stitching to ensure

that padding and linings are intact.

– Fasten duvet covers and pillow

cases to prevent small items from

being trapped inside them.

–Fasten hooks and eyes etc.

–Tie fabric belts and apron strings.

–Sew in or remove underwiring from

bras.

BTurn on the tumble dryer

^Switch the dryer on by pressing the

On/Off jk button in.

The tumble dryer may be switched on

after loading, saving energy as the light

will not come on.

CLoad the tumble dryer

^Press the Door button to open the

door.

^Load the laundry loosely into the

drum.

Do not overload the drum. See the

"Programme chart" for

recommended loads for each pro-

gramme.

Overloading can cause unnecessary

wear and tear to the laundry and

give a disappointing drying result.

^Before closing the door make sure

the fluff filter is correctly positioned.

Check the laundry is right inside the

drum so that it cannot get trapped or

damaged when the door is shut.

^Shut the door either with a gentle

swing, or lean against it and push it

shut.

How to dry correctly

DSelect a programme

^Select the programme you want.

The indicator for the programme

selected will light up.

A drying level or extra option indicator

may also light up and the duration may

also be displayed.

Drying level programmes

–Cottons, Minimum iron, Delicates,

Proofing, Express, Automatic plus,

Denim, Shirts

^Press the drying level button

repeatedly until the indicator for the

drying level you want lights up (for

almost all programmes).

Any of the four drying levels can be

selected for the Cottons and Express

programmes. A more limited range is

available when using other

programmes and with some the drying

level is pre-set and cannot be changed.

Note

You can extend the range of the drying

levels for some programmes (see

"Programmable functions").

Woollens handcare, Gentle

smoothing

–This programme cannot be changed.

Selecting the duration of the timed

drying Cool air and Warm air

programmes

The indicator light for the Delay start

button will flash when the Cool air or

Warm air programme is selected.

^Press the Delay start button

repeatedly until the required duration

shows in the display.

You can select the duration in stages

for:

–Cool air: from 20 minutes up to 1:00

hour.

–Warm air: from 15 minutes up to 2:00

hours.

ESelect any Extra options / Delay

start

^Low temperature, Buzzer and Delay

start (see "Extra options/Delay start)"

are selected by pressing the

appropriate button.

Anti-crease (see next page) is

permanently switched on.

N.B.: It is not possible to select Delay

start when using the Warm air or Cool

air programmes.

How to dry correctly

FStart the programme

The Start/Stop button will flash when a

programme is being selected. The

flashing indicates that a programme

can be started.

^Press the Start/Stop button.

The Start/Stop button will now light up

constantly.

The Perfect Dry indicator will flash or

light up constantly with the sensor

controlled drying programmes. It will

not come on at all with timed drying

programmes (see "Operating the

tumble dryer").

Please note: The duration shown in the

display is an estimate and can vary.

Before the end of a programme

There is a cooling down phase at the

end of the drying sequence (Cooling

down will light up). The programme will

not finish until the cooling down phase

has been completed.

There is no cooling down phase at the

end of the Woollens handcare program-

me.

GRemove the laundry at the end of

the programme

0and Finish will appear in the display

to indicate that the programme has

finished. The buzzer (if selected) will

sound at intervals.

The drum will continue to rotate at

intervals for up to two hours to prevent

laundry creasing, if you do not wish to

remove it immediately (anti-crease).

There is no anti-crease phase at the

end of the Woollens handcare program-

me.

^Press the Door button.

^Open the door.

^Remove the laundry.

Check that all items have been

removed from the drum. If items are

left in the dryer, they could be

damaged by overdrying when the

dryer is next used.

If the dryer is switched on at the mains

and the door is opened, the drum

lighting will come on. It will go out a few

minutes later to save energy.

^Press the jk button to switch the

dryer off.

^Clean the fluff filters.

^Close the door.

^Empty the condensed water

container (unless the dryer has been

connected for external drainage).

^The condenser unit should be

checked and cleaned on a regular

basis (see "Cleaning and care").

How to dry correctly

Extra options

Low temperature

Delicate and minimum iron fabrics with

the rsymbol on the care label (e.g.

acrylic garments) are dried at a lower

temperature. The programme duration

is longer.

On some programmes Low tempera-

ture is permanently activated and so

cannot be deselected.

Buzzer

A buzzer sounds (at intervals for a

maximum of 1 hr) to let you know the

programme has finished.

A continuous alarm will sound if there is

a fault even if the buzzer has been

switched off.

Delay start

You can delay the start of a programme

by 30 minutes up to 24 hours.

^Select a programme.

^Press the Delay start button

repeatedly until the required delay

period shows in the display.

–The Delay start indicator light will

flash.

–Times of up to 10^ are selected in

steps of half an hour, and more than

10^ in one-hour steps.

–If you keep the Delay start button

pressed in, the time will continue to

increase up to 24^.

To begin delay start

^Press the Start/Stop button.

–The Delay start indicator will light up

constantly.

–Delay start times of more than 10^

will count down in hours, and of less

than 10^ in minutes to the start of the

programme.

–The drum will turn briefly every hour

to help prevent creasing.

To cancel / alter delay start

^Press the Start/Stop button to cancel

delay start.

^To alter the delay start time, press the

Delay start button repeatedly until the

required delay period shows in the

display.

^Press the Start/Stop button to start

the altered delay start time counting

down from the beginning again.

To add laundry after the delay start

time has started counting down

While the delay start time is counting

down, you can still add laundry to the

drum:

^Switch the dryer off.

Opening the door without switching the

dryer off will cancel delay start.

^Open the door and add the laundry.

^Close the door and switch the dryer

back on again.

Extra options / Delay start

Cottons Max. load 7 kg*

Extra dry, Normal**

Use for Single and multi-layered cotton fabrics such as towelling,

T-shirts, underwear, flannelette bed linen.

Notes –Select Extra dry for multi-layered and very thick fabrics.

–Do not use Extra dry for loopknit fabrics (e.g. T-shirts,

underwear, baby clothes), as they have a tendency to

shrink.

Low temperature Select the Low temperature option for delicate fabrics with the

rsymbol on the care label.

Hand iron, Machine iron

Use for Cottons or linen fabrics, e.g.: table linen, bed linen, starched

laundry.

Note – To prevent laundry from drying out it should be rolled up

until you are ready for ironing.

Low temperature Select the Low temperature option for delicate fabrics with the

rsymbol on the care label.

Minimum iron Max. load 3.5 kg*

Normal, Hand iron

Use for Minimum iron items made of cotton, synthetic or blended

fabrics, e.g.: dresses, trousers, skirts and table cloths.

Low temperature Select the Low temperature option for delicate fabrics with the

rsymbol on the care label.

Delicates Max. load 2.5 kg*

Normal, Hand iron

Use for Delicate items made of synthetic fibres, easy care cotton or

blended fabrics, e.g. shirts, blouses, lingerie and appliquéd

garments.

Low temperature Low temperature cannot be deselected.

* Weight of dry laundry

** Note for test institutes:

Test programme (without selecting any Extra options) in accordance with

Regulation 392/2012/EU for energy labelling measured in accordance

with EN 61121.

Programme chart

Woollens handcare Max. load 2 kg*

Fabric type Woollen fabrics

Notes –This programme only fluffs up woollen garments. They are

not dried completely by this programme.

–Remove garments as soon as the programme has finished

and leave to finish drying at room temperature.

Low temperature Low temperature cannot be deselected.

Proofing Max. load 2.5 kg*

Normal

Fabric type For drying microfibre fabrics, skiwear, fine, closeweave cotton

garments (poplin) or tablecloths which are suitable for drying

in a tumble dryer and have been treated to provide a water

and dirt resistant finish.

Notes – This programme includes a proofing fixing phase.

–Only use proofing agents containing fluorochemical

compounds which are stated by the manufacturer as

being "suitable for use on membrane textiles.

–Do not dry items which have been treated with proofing

agents containing paraffin. Fire hazard!

Express Max. load 3.5 kg*

Extra dry, Normal, Hand iron, Machine iron

Fabric type Fabrics which can tolerate high temperatures with the q

symbol on the care label and which can be dried in the

Cottons programme.

Note –The programme duration is shorter.

Automatic plus Max. load 5 kg*

Normal, Hand iron

Fabric type Mixed loads of garments suitable for the Cottons and Mini-

mum iron programmes. Sort according to colour.

Denim Max. load 3 kg*

Normal, Hand iron

Fabric type Denim garments, e.g. jeans, jackets, skirts, shirts.

Low temperature Select the Low temperature option for delicate fabrics with the

rsymbol on the care label.

* Weight of dry laundry

Programme chart

Shirts Max. load 2 kg*

Normal, Hand iron

Fabric type Shirts and blouses.

Low temperature Select the Low temperature option for delicate fabrics with

the rsymbol on the care label.

Cool air Max. load 7 kg*

Fabric type Any item which only needs airing.

Warm air Max. load 7 kg*

Fabric type –Voluminous and multi-layered fabrics whose layers have

different drying characteristics, e.g. jackets, pillows.

–For drying individual items, e.g. bath towels, swimwear,

tea-towels.

Note – Do not select the longest drying time to start with. Check

the items as you are drying them to find the optimum time.

Low temperature Select the Low temperature option for delicate fabrics with

the rsymbol on the care label.

Note You can use the Warm air programme to help remove odours

from clean cotton clothing (select a duration of between 1/2

and 1 hour). Items must be suitable for drying in a tumble

dryer. Dampen the garments a little beforehand or add a

fabric conditioner sheet. Odours will not be removed as

effectively from any parts of the garments which are made of

synthetic fibres.

Gentle smoothing Max. load 1 kg*

Fabric type –Cotton and linen fabrics.

–Minimum iron items made of mixed fibres, cottons or

synthetics, e.g.: trousers, anoraks, shirts.

Notes –Smooths out creasing caused during the spin cycle in the

washing machine.

–Remove garments as soon as the programme has finished

so that they are easy to iron.

Low temperature Low temperature cannot be deselected.

* Weight of dry laundry

Programme chart

Once a programme has started

- changing the programme

You cannot change to another pro-

gramme once a programme has started

(this prevents unintentional alterations).

You will need to cancel the current pro-

gramme before you can select a new

one.

- cancelling the programme and then

selecting a different programme

^Press the Start/Stop button.

The items will be cooled down,

depending on the temperature

reached and how long they have

been dried for.

If you press the Start/Stop button

again during the cooling down

phase, Finish will light up in the dis-

play.

^Press the Door button.

^Close the door.

^Select another programme and start

it.

- cancelling the programme and then

removing the laundry

^Proceed as described in "Adding or

removing laundry after a programme

has started" below.

^Switch the dryer off after closing the

door.

Altering Delay start

^See "Delay start".

Adding or removing laundry

after a programme has started

^Press the Door button.

^Open the door.

,Danger of burning:

Do not touch the back of the drum

when adding or removing items. The

drum and the items can get very hot.

^Add or remove items as required.

^Close the door.

^Press the Start/Stop button.

Time remaining

The time left shown in the display may

now vary from the actual drying time.

Changing the programme sequence

The system lock prevents the dryer

being used without your knowledge.

It can be activated if wished.

The dryer's electronics are then locked.

The dryer can still be switched on but a

programme cannot be started.

–If an attempt is made to start a pro-

gramme, the indicator light for the

Low temperature button will come on

and a key symbol 0-§ will appear in

the display.

The door is not locked and can be

opened at any time.

To activate the lock

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Low temperature button

and keep it pressed in whilst carrying

out steps Bto E.

BPress the jk button in.

The Automatic plus indicator light will

come on.

CSlowly turn the programme selector

three positions stage by stage in a

clockwise direction.

Each of the three programme

indicator lights must come on one

after the other.

DNow slowly turn the programme

selector six positions stage by stage

in an anti-clockwise direction.

Each of the six programme indicator

lights must come on one after the

other.

The indicator light for the Low tempera-

ture button will flash, and a key symbol

0-§ will appear in the display.

ERelease the Low temperature button.

The electronics have now been locked.

^Switch the dryer off.

To deactivate the lock

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

^The procedure is the same as for

activating the lock. Carry out steps A

to Eas described previously.

At step Ethe indicator light for the Low

temperature button will stop flashing

and the key symbol 0-§ will go out.

The electronics are no longer locked.

Electronic system lock

Emptying the condensed

water container

The condensed water will be collected

in the condensed water container

unless the dryer has been connected

for external drainage (see "Installation").

Empty the condensed water

container after every drying pro-

gramme.

The Empty container indicator will light

up if the maximum level of the

condensed water container is reached.

The indicator light will go out when the

door is opened and closed again.

^Pull out the condensed water

container.

^To prevent water running out, hold it

at the front and towards the back and

keep it in a horizontal position when

carrying it.

^Empty the container.

^Replace the container in the dryer.

,Condensed water should not be

consumed. It could lead to health

problems for people and animals.

Condensed water can be put to

household use (e.g. in a steam iron or

humidifier). To ensure that any residual

particles of fluff in the condensed water

are removed before use, pass it

through a fine sieve or paper filter first.

Cleaning and care

Cleaning the fluff filters

The fluff which is created by the drying

process is collected by the fluff filters in

the door and the door opening. Clean

the filters after each drying program-

me*.

Cleaning them whilst dry

Tip: You can also use a vacuum

cleaner to remove the fluff.

^Open the door and pull the fluff filter

(1) out of the door as illustrated.

^Use your fingers to remove the fluff

from the surface of the filter.

^Remove any fluff from the hollow part

of the door opening. You could also

use a cleaning brush which is

available as an optional extra from

your Miele dealer or the Miele Spare

Parts Department, or use a vacuum

cleaner.

^Also clean the door seal (2) with a

damp cloth.

^Once clean, push the filter back into

the door holder until it clicks into

position. Ensure it is facing the

correct way.

^Use your fingers or a vacuum cleaner

to remove the fluff from the two fluff

filters in the door opening.

^Close the door.

* Always check the fluff filters if the

Clean out airways indicator light

comes on.

Cleaning and care

Cleaning them with water

If there is a great deal of compacted

fluff on any of the filters, they can be

removed and cleaned under hot

running water.

^Open the door and pull the fluff filter

out of the door as described

previously.

The two filters in the door opening can

also be removed if you need to clean

them with water.

^Turn dial aand pull the filter by the

dial out of the door opening as shown

b. Do the same on the other side.

^Rinse all the filters under hot, running

water.

^Then shake the filters until no more

water droplets are visible.

^Dry the filters thoroughly with care.

^Clean the area underneath these

filters, e.g. with a vacuum cleaner.

,Do not replace them if they are

damp or wet. Damp or wet filters

could cause operational faults.

^Push the large filter back into the

door holder until it clicks into position.

Ensure it is facing the correct way.

^Replace the filters in the door

opening by first inserting them at the

bottom and then pressing them into

place at the top.

^Lock both dials.

Cleaning and care

Cleaning the tumble dryer

Disconnect the tumble dryer from

the mains electricity supply.

Miele branded cleaning and

conditioning products are available to

order via the internet on

www.miele-shop.com.

^Clean the housing and control panel

with a slightly damp cloth and a mild

detergent or soapy water.

^The drum and other stainless steel

parts can be cleaned with a suitable

stainless steel cleaner following the

manufacturer's instructions.

Do not use solvents, abrasive

cleaners, glass cleaners or

all-purpose cleaners. These could

damage plastic sufaces and other

parts.

^Dry all parts with a soft cloth.

Cleaning and care

Cleaning the condenser unit

Detergent residue, hair and fine fluff

from the dryer can get through the fluff

filters and block the condenser unit.

Dust from the room in which the dryer is

installed can also get into the

condenser unit and cause a blockage.

Check the condenser unit at least

once a year. Always check it if the

Clean out airways indicator light

comes on. Clean it if necessary.

Removing the condenser unit

^Open the service panel. Hold the

panel securely when doing this.

^Now remove the panel by pulling it

diagonally upwards and place it to

one side.

^Turn the lever on the inner cover

downwards to the vertical position.

^Tilt the cover forwards.

^Remove it by pulling it diagonally

upwards.

^Turn the lever on the condenser unit

upwards to the vertical position so

that the hook on the lever is no longer

in the groove at the bottom of the

condenser unit housing.

Cleaning and care

^Pull the condenser unit out of its

housing by the handle.

Checking the condenser unit

^Hold the condenser unit up to the

light as shown.

^Check to see if there is any fluff

inside it.

The arrows in the illustration above

indicate where to look.

If you cannot see any fluff:

^Replace the condenser unit (see

following page).

If you can see some fluff:

^Clean the condenser unit as

described below.

Cleaning the condenser unit

^When rinsing the condenser unit,

make sure you position it as

shown in the next two illustrations.

^Use a shower head or similar to rinse

the unit out as shown.

Cleaning and care

^Then flush the unit through from the

front.

^Check the condenser unit again for

any visible fluff and if necessary flush

it through again until it has all gone.

^Repeat as required.

^Also make sure the rubber seals are

clean.

The rubber seals must not be

removed and must be free of kinks.

^Shake the water off the condenser

unit until no more droplets of water

are visible.

Checking and cleaning the

condenser unit housing

^Remove any soiling still visible inside

the housing unit by hand using a

damp cloth. Do not try and access

areas you cannot reach by hand!

Replacing the condenser unit

^With the handle facing upwards,

push the condenser unit back into

position in its housing.

^Turn the lever down to the horizontal

position, making sure that the hook

on the lever clicks into the groove.

When replacing the inner cover after

cleaning, ensure that the rubber seal

fits correctly into the groove.

^Replace the inner cover making sure

the hooks locate correctly. Hold it at

an angle and push it gently

downwards.

^Then turn the lever upwards into the

horizontal position to lock the cover.

^Replace the service panel and press

the upper edge until it clicks into

position.

,It is important to ensure that both

the condenser unit and the cover

are correctly positioned and locked,

otherwise water may leak from the

dryer.

Cleaning and care

With the help of the following notes minor faults in the performance of the

appliance, some of which may result from incorrect operation, can be put right

without contacting the Service Department.

,Repair work to electrical appliances should only be carried out by a

suitably qualified person in strict accordance with current local and national

safety regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

Check and fault messages

Problem Possible cause Remedy

0-§ appears in

the display.

The Low tempe-

rature indicator

light is flashing.

The electronic system lock is

activated.

You will need to deactivate

the system lock before the

dryer can be used (see

"Electronic system lock").

The programme

stops and

0and Finish

appear in the

display.

The buzzer

sounds.

This is not a fault.

The electronic unit has

recognised that there is no

laundry or insufficient laundry

in the drum and cancelled the

programme. Drying individual

garments or items which are

already dry can also cause the

programme to be cancelled.

Use the Warm air program-

me for drying individual

items.

– Open and shut the door.

The programme

stops.

The buzzer

sounds.

Cooling down or

Finish may also

flash in the dis-

play.

No obvious cause. –Switch the dryer off and

back on again.

–Then start the programme

again.

If this problem happens

again, there is a fault.

Contact Miele.

Bars are

flashing at the

end of the pro-

gramme:

—œ–...C~–...Cœ˜...

The programme has finished

but the laundry is still being

cooled down.

You can either unload the

drum and leave the laundry

to cool at room temperature

or leave it in the dryer to

continue cooling.

Problem solving guide

Problem Possible cause Remedy

The Clean out

airways indicator

light comes on.

The dryer is not working

efficiently or economically.

Possible cause: the filters

are clogged with fluff or with

detergent residues.

–Cleaning the filters is

usually all that is required.

However, if the reminder

does not go out after you

have cleaned the filters,

then also check all the

possible causes

described under "The

drying process goes on

too long or even switches

off".

To switch off this

reminder:

– Open and shut the door

with the dryer switched

on.

The Clean out airways

indicator light can be

deactivated (see

"Programmable functions").

The programme

stops and

the Clean out

airways indicator

light comes on.

The buzzer

sounds.

See above for possible

causes and their remedies.

To switch off this warning:

– Open and shut the door

with the dryer switched

on.

–Then start the programme

again.

–If this problem happens

again, contact Miele.

The Empty

container indicator

light comes on.

The buzzer

sounds.

The condensed water

container is full or there is

kink in the drain hose.

–Empty out the condensed

water container.

–Check the drain hose.

To switch off this warning:

–Open and shut the door

with the dryer switched

on.

Problem solving guide

Problem Possible cause Remedy

The Start/Stop button is

flashing slowly and the

display is dark.

The dryer is in Standby

mode.

This is quite normal and

not indicative of any fault.

See "Programmable

functions".

Sometimes a program-

me cannot be started

and the corresponding

programme indicator

light does not light up.

No obvious cause. –Switch the dryer off

and back on again.

–Select one of the

programmes that

would not start.

–If it still will not start,

there is a fault. Contact

the Miele Service

Department.

The Start/Stop button

flashes on and off.

The flashing indicates

that a programme can be

started.

After the programme has

started, the flashing will

change to a constant

light.

Problem solving guide

An unsatisfactory drying result

Problem Possible cause Remedy

The laundry is not

sufficiently dry.

The load consisted of

different fabrics.

–Finish drying using the

Warm air programme.

–Select a different pro-

gramme next time *.

Items made of synthetic

fibres are charged with

static electricity after

drying.

Synthetic fibres tend to

attract static charge.

Static charge can be

reduced by adding a

fabric conditioner to the

final rinse in the washing

programme or a fabric

conditioner sheet to the

load when drying.

There is a build-up of

fluff.

Fluff is principally the

result of friction when

garments are being worn

and to some extent when

they are being washed.

Machine drying does not

affect the lifetime of the

fabric.

Fluff is collected by the

fluff filters and can be

removed easily (see

"Cleaning and care").

* You can alter the drying levels for some programmes (see "Programmable

functions" at the the end of this booklet).

Problem solving guide

Other problems

Problem Possible cause Remedy

The drying process

goes on too long or

even switches off.

In some circumstances, the

Clean out airways indicator

light still comes on, even

though the filters are clean.

Please check all the

possible causes and

switch the dryer off and

then back on again.

Ventilation to and from the

dryer may be insufficient,

e.g. because it is installed in

a room which is too small.

This can cause the tempera-

ture in the room to rise

sharply.

Open a door or window

while the dryer is in

operation for increased air

flow.

The vents below the door are

blocked.

– Remove any objects

that are blocking the

vents.

The fluff filters are clogged

up with fluff or were still wet

when they were replaced.

– Remove any fluff.

– The fluff filters must be

completely dry.

Detergent residues, hair and

fine fibres can block the

condenser unit.

Check the condenser unit

from time to time and

clean it if necessary.

The laundry has not been

spun sufficiently.

Make sure that your

laundry is thoroughly spun

at the appropriate spin

speed in the washing

machine.

The tumble dryer has been

overloaded.

Do not exceed the

maximum load for the pro-

gramme selected.

Metallic components, e.g.

zips have prevented the

dryer from registering the

correct moisture level in the

laundry.

–Open zips next time.

If the problem occurs

again, dry garments with

long zips using the Warm

air programme (timed

drying).

Problem solving guide

Problem Possible cause Remedy

Water leaks from the

dryer after the

condenser unit has

been cleaned.

–The inner cover of the

condenser unit has not

been locked properly

and/or the condenser

unit has not been

positioned correctly.

–Fluff has collected in

the condenser unit

housing.

–Ensure that the

condenser unit is

positioned correctly

and lock the inner

cover.

–Check the rubber

seals.

–Use a cloth to remove

any visible fluff from the

inside of the condenser

unit housing.

The programme does

not start.

No obvious cause. –Is the dryer switched

on?

– Is the plug correctly

inserted into the socket

and switched on?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

Power cut. A programme which was running previously will

continue automatically when power is restored to the

tumble dryer as long as the Cooling down phase had

not been reached.

The interior drum

lighting does not come

on.

The lighting switches off

automatically (to save

energy).

–Switch the dryer off

and then on again.

–If the lamp needs to be

replaced, follow the

instructions in

"Changing the lamp".

Problem solving guide

Changing the lamp

Disconnect the tumble dryer from

the mains electricity supply.

^Open the door.

You will find the interior light cover at

the top of the drum aperture.

^Insert a suitable tool, such as a wide

bladed screwdriver, under the side

edge of the light cover as illustrated.

^Apply a little pressure and whilst

doing so turn your wrist in the

direction of the arrow to open the

cover.

The cover will open downwards.

The temperature resistant lamp should

only be ordered from your Miele Dealer

or the Miele Spare Parts Department.

The light specification and maximum

wattage is stated on the data plate

and on the light cover.

^Turn the light anti-clockwise to

remove.

^Replace the lamp.

^To close the cover push it upwards

and press it on the left and right until

you hear it click into position.

,Ensure that it is fitted into

position securely, as any moisture

could cause a short circuit.

Problem solving guide

Repairs

In the event of any faults which you

cannot remedy yourself, please contact

–your Miele dealer or

–the Miele Service Department (see

back cover for contact details).

When contacting your dealer or the

Service Department, please quote the

model and serial number of your

appliance, both of which are shown on

the data plate. This is visible when you

open the door.

N.B. A call-out charge will be

applied for service visits where the

problem could have been resolved

as described in these instructions.

Future updates (PC)

The indicator or check light marked PC

on the fascia panel is the interface used

by the Miele service technicians during

service work for testing purposes and

for updating the appliance's program-

me data.

Appliance guarantee

In the U.K. your appliance is

guaranteed for 2 years from the date of

purchase. However you must activate

your cover by calling 0845 365 6640 or

registering online at www. miele.co.uk.

For information on the appliance

guarantee specific to your country

please contact Miele. See back cover

for contact details.

Optional accessories

Optional accessories for this dryer are

available from your Miele Dealer, the

Miele Spare Parts Department or via the

internet at www.miele-shop.com.

Please note that telephone calls may

be monitored and recorded for

training purposes.

After Sales service

Front view

aMains connection cable

bCondensed water container

cControl panel

dDoor

eService panel for condenser unit

fFour height-adjustable screw feet

gExternal drainage options (e.g. via

wash basin, wash basin drain outlet,

or gully. See "External condensed

water outlet").

Installation

Rear view

aProtruding lid for holding when

moving the dryer (see arrows)

bAir inlet vent for cooling the

condenser unit

cMains connection cable

dHose for external drainage of

condensed water

eAccessories for connection to a sink

drain outlet

Installation site

,Make sure the dryer door can be

opened without hindrance after in-

stallation.

Transporting the dryer to its

installation site

When moving the dryer, hold it by the

lid where it protrudes to the rear. To

manoeuvre the dryer out of its packing

case to its installation site hold it by the

front feet and the base of the lid.

Building under a continous worktop /

in a kitchen run

,Abuilding-under kit* with a

coverplate to replace the appliance

lid is required. It must be fitted by a

suitably qualified person to ensure

electrical safety.

N.B. If you wish to push your appliance

under a worktop and there is space to

do this without removing the lid the

building-under kit is not necessary.

Otherwise it is essential.

– The building-under kit is supplied

with its own installation instructions.

– N.B. When built-under drying times

may be longer.

– The electrical socket must be

located in an accessible position

near the appliance.

With niche heights of:

– 830-840 mm, longer screw feet* are

required.

–870-885 / 915-930 mm, one or two

raising kits* are required.

* Miele accessory available to order

Replacing the lid

If the lid has been removed in order to

fit a coverplate, ensure that, if the lid is

ever replaced, it fits securely into the

rear holders. Otherwise, it is not

properly secure for transport.

Installation

Levelling the appliance

The dryer must be perfectly level to

ensure safe and proper operation.

^The screw feet can be adjusted to

compensate for any unevenness in

the floor.

,The air inlet and outlet vents on

the front of the dryer must not be

covered as this would prevent

sufficient ventilation for cooling the

condenser unit.

,Do not block the gap between

the bottom of the tumble dryer and

the floor with plinth facings, deep

pile carpet etc. This would hinder a

sufficient flow of air to the dryer.

Room ventilation

The air which is taken in when the dryer

is in operation is blown out of the front

of the dryer and warms up the air in the

room. It is very important to ensure

adequate ventilation, e.g. by opening a

window. Otherwise drying times may be

longer.

Washer-dryer stack

The tumble dryer can also be

combined with a Miele washing

machine in a washer-dryer stack. The

appropriate "WTV" stacking kit

(available to order) to match your dryer

is required.

,Stacking kits must only be

installed by a suitably qualified fitter.

Before moving the tumble dryer

again (e.g. when moving house)

After each use a small quantity of

condensed water will collect in the area

around the pump. This water can run

out if the dryer is tipped up when it is

being moved. It is a good idea to run

the Warm air programme for

approximately 1 minute before moving

it. Any remaining condensed water will

then be fed into the condensed water

container or out through the drain hose.

Installation

External condensed water

outlet

General notes

When drying is in progress, condensed

water is pumped into the condensed

water container through the drain hose at

the back of the dryer. The condensed

water can also be drained off directly if

the tumble dryer is installed near a sink,

drain outlet etc. so that the condensed

water container does not have to be

emptied.

Drain hose length ............1.50 m

Maximum delivery head .......1.50 m

Maximum drain hose length ....4.00 m

,If the on-site water drainage sy-

stem is not fitted with a non-return

valve or an appropriate air gap, one

must be fitted to prevent the risk of

back-flow. (See "Installation conditions

requiring a non-return valve").

The following optional accessories are

available:

–an extension hose

–a non-return valve kit for connection

to an external condensed water

outlet (includes an extension hose).

Maximum delivery head with

non-return valve fitted: 1.00 m

Arranging the drain hose

,Do not pull on the drain hose and

do not stretch it or allow it to become

kinked as it could get damaged.

^There will be a small amount of

residual water in the drain hose.

Have a container ready to collect

this.

^Pull the hose off its connection (see

arrow).

^Allow any residual water to run into

the container.

^Unwind the hose and pull it carefully

out of the holders.

^Position the hose to the right or left

hand side as necessary.

Leave the hose in the middle holder to

prevent it from becoming kinked

inadvertently.

Installation

External drainage via a sink or gully

^See "Front view" illustration.

,If you want to drain the water off

into a sink you will need to secure

the hose carefully, e.g. by tying it to

a tap to make sure it cannot slip

during use. Otherwise there is a risk

of overflowing water which could

cause damage.

^Use the bow-shaped guide to

prevent the drain hose from

becoming kinked.

Installation conditions requiring a

non-return valve

,Certain installation conditions

require the fitting of a non-return

valve for external water

connection (available as an

optional accessory). A non-return

valve will prevent the risk of

back-flow out of the dryer which

could cause damage.

A non-return valve is required:

–If the tumble dryer is connected to a

sink drain outlet (see the following

section).

–If the tumble dryer is connected to a

drainage system already in use by

another appliance, e.g. a dishwasher

or washing machine.

Example: Connection to a sink drain

outlet

The drain hose with non-return valve

fitted can be connected directly to a

suitable sink drain outlet.

^Remove the following from the back

of the dryer at the top:

Adapter 1and hose clip 3behind it.

Installation

1 Adapter

2 Nut

3 Hose clip

4 End of the hose

5 Non-return valve

6 Tumble dryer drain hose

^Fit adapter 1to the sink drain outlet

using nut 2.

If this nut has a flat disc in it you

should take the disc out first.

^Attach the end of hose 4to adapter

^Use a screwdriver to tighten hose

clip 3up close to the nut.

,Non-return valve 5has to be

fitted with the arrow pointing in the

direction of flow (i.e. towards the

sink). Otherwise water will not drain

out of the appliance.

^Fit non-return valve 5to tumble dryer

drain hose 6(make sure it is fitted in

the correct direction - see arrow on

non-return valve).

^Secure the non-return valve using

hose clips.

Installation

Electrical connection U.K.

All electrical work should be carried out

by a suitably qualified and competent

person, in strict accordance with

current national and local safety

regulations (BS 7671 in the UK).

Ensure power is not supplied to the

appliance until after installation work

has been carried out.

The appliance is supplied with a mains

cable with moulded plug ready for

connection to a 230-240V mains

supply. Please ensure the connection

data quoted on the data plate match

the household mains supply.

Connection should be made via a

suitable switched socket which is easily

accessible after installation.

For extra safety it is advisable to protect

the appliance with a suitable residual

current device (RCD). Contact a

qualified electrician for advice.

Do not connect via an extension lead.

Extension leads do not guarantee the

required safety of the appliance (e.g.

danger of overheating).

Non-rewireable plugs BS 1363

The fuse cover must be refitted when

changing the fuse, and if the fuse cover

is lost, the plug must not be used until a

suitable replacement is obtained. The

colour of the correct replacement cover

is that of the coloured insert in the base

of the plug, or the colour that is

embossed in words on the base of the

plug (as applicable to the design of

plug fitted).

Replacement fuses should be ASTA

approved to BS 1362 and have the

correct rating. Replacement fuses and

fuse covers may be purchased from

your local electrical supplier.

WARNING: THIS APPLIANCE

MUST BE EARTHED

Electrical connection

Load1Final spin speed

in a domestic washing

machine

Residual

moisture

Energy Duration

kg rpm % kWh Minutes

Cottons Normal27.0

3.5

1000

4.14

2.28

109

Cottons Normal 7.0

7.0

1200

1400

1600

1800

3.75

3.55

3.15

3.10

100

Cottons Normal

+ Low temperature 7.0 1000 60 4.20 175

Cottons Hand iron 7.0

7.0

1000

1200

1400

1600

1800

3.10

2.75

2.55

2.20

2.10

Minimum iron Normal 3.5 1200 40 1.40 45

Minimum iron Normal

+ Low temperature 3.5 1200 40 1.50 73

Minimum iron Hand iron 3.5 1200 40 1.20 39

Automatic plus Normal 5.0 800 50 2.70 114

Shirts Normal 2.0 600 60 1.40 59

Delicates Normal 2.5 700 50 1.55 116

Proofing Normal 2.5 800 50 1.85 96

Denim Normal 3.0 900 60 2.40 119

Express Normal 3.5 1000 60 2.20 69

Gentle smoothing 1.0 1000 60 0.75 32

Woollens handcare 2.0 1000 50 0.15 4

1Weight of dry laundry

2Test programme in accordance with Regulation 392/2012/EU for energy labelling measured in

accordance with EN 61121.

All data was calculated using EN 61121 unless otherwise stated.

Notes for test institutes:

Before testing in accordance with EN 61121, drya3kgload of cotton laundry with 70% residual

moisture as per the above standard using the Cottons Normal programme without any extra options.

Consumption data can vary from the nominal values given above depending on the size of the

load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity

supply and any extra options selected.

Consumption data

Height 850 mm

Width 595 mm

Depth 587 mm

Depth with door open 1062 mm

Height for building under 820 mm

Width for building under 600 mm

Depth for building under 600 mm

Suitable for pushing under a

worktop

yes

Suitable for stacking yes

Weight 51 kg

Drum volume 111 l

Maximum capacity 7 kg dry weight

Capacity of condensed water

container

approx. 4.2 l

Drain hose length 1.5 m

Maximum delivery head 1.5 m

Maximum drain hose length 4 m

Length of connection cable 2 m

Voltage

Connected load

Fuse rating see data plate

Lamp wattage

Test certificates awarded

Energy consumption see "Consumption data"

Technical data

Altering the residual moisture

level in the Cottons

programme

The tumble dryer is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier or damper, you can reduce

or increase the default residual

moisture in the Cottons programme.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

–The Low temperature indicator light

will flash once briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Increased residual moisture.

Laundry damper.

IStandard residual moisture

(factory default setting)

(the Automatic plus indicator light will

also flash once).

2Reduced residual moisture.

Laundry drier.

(the Automatic plus indicator light will

also flash twice).

DPressing the Start/Stop button

switches between the options.

ESwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato C.

^Switch the dryer off after step C.

Programmable functions

Altering the residual moisture

level in the Minimum iron

programme

The tumble dryer is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier or damper, you can reduce

or increase the default residual

moisture in the Minimum iron pro-

gramme.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

once.

–The Low temperature indicator light

will flash twice briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Increased residual moisture.

Laundry damper.

IStandard residual moisture

(factory default setting)

(the Automatic plus indicator light will

also flash once).

2Reduced residual moisture.

Laundry drier.

(the Automatic plus indicator light will

also flash twice).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Anti-crease

Anti-crease helps prevent creasing, if

laundry is not normally removed

immediately after the end of a pro-

gramme.

The anti-crease function

–is activated when the tumble dryer is

delivered. You can shorten the

duration of the anti-crease phase or

deactivate it if wished.

–is used in all programmes except

Woollens handcare.

– should be left activated.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

twice.

–The Low temperature indicator light

will flash 3 times briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Anti-crease off

i1 hour anti-crease

(the Automatic plus indicator light will

also flash once).

22 hours anti-crease

(factory default setting)

(the Automatic plus indicator light will

also flash twice).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Altering the volume of the

buzzer

The buzzer has two volumes.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

–The tumble dryer is switched off.

–The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

three times.

– The Low temperature indicator light

will flash four times briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Normal buzzer

(factory default setting)

ILoud buzzer

(the Automatic plus indicator light will

also flash)

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Altering the standard drying

level in the Automatic plus

programme

The tumble dryer is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier or damper, you can reduce

or increase the default residual

moisture in the Automatic plus pro-

gramme.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

four times.

–The Low temperature indicator light

will flash six times briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Increased residual moisture.

Laundry damper.

IStandard residual moisture

(factory default setting)

(the Automatic plus indicator light will

also flash once).

2Reduced residual moisture.

Laundry drier.

(the Automatic plus indicator light will

also flash twice).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Extending the cooling down

time

The cooling down phase which takes

place before the end of a programme

can be extended by 5 or 10 minutes,

if required. This makes the garments

easier to handle.

The cooling down time can only be

extended for programmes with drying

levels.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

five times.

–The Low temperature indicator light

will flash seven times briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Cooling down time not extended

(factory default setting)

iCooling down time extended by

five minutes

(the Automatic plus indicator light will

also flash once).

2Cooling down time extended by

ten minutes

(the Automatic plus indicator light will

also flash twice).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Standby

To save energy, the display and the

programme sequence/check lights

go out after 10 minutes and the

Start/Stop button starts flashing

slowly.

To come out of standby mode

^Turn the programme selector or

press a button. Neither will have any

effect if a programme is running.

The standby function is activated and

the display and programme

sequence/check lights will go out after

10 minutes:

– if a programme is not selected after

the dryer has been switched on.

– after a programme has started.

They will, however, come on for 10

minutes after a delay start time has

counted down, at the end of the pro-

gramme or the end of the anti-crease

phase.

The buzzer (if selected ) will sound for

10 minutes at the end of the program-

me.

Factory default. Not in current pro-

gramme

As described under "On".

However, the display and programme

sequence/check lights will stay on after

the programme has started and remain

visible during the programme.

Off

The display and programme

sequence/check lights will stay on while

the dryer is switched on.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

^See next page.

Programmable functions

Before you begin, ensure that:

–The tumble dryer is switched off.

–The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button six

times.

– The Low temperature indicator light

will flash 8 times briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0On

IFactory default setting. Not in

current programme

(the Automatic plus indicator light will

also flash once).

2Off

(the Automatic plus indicator light will

also flash twice).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Memory function

The electronics will memorise any

extra options selected for a program-

me. The duration selected for the

Warm air or Cool air timed drying

programmes will also be stored in

memory.

These settings will be selected

automatically the next time the pro-

gramme is chosen. You can either

accept these or change them by

pressing the appropriate button.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

seven times.

–The Low temperature indicator light

will flash 9 times briefly.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Memory deactivated

(factory default setting)

IMemory activated

(the Automatic plus indicator light will

also flash)

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Clean out airways indicator

Fluff should be removed after drying.

The Clean out airways indicator will

remind you to clean the filters when a

certain amount of fluff has collected

in the filters. You can decide at what

level of fluff this reminder should be

given.

You will have an idea of how often this

should be done after a few drying

programmes.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

eight times.

–The Low temperature indicator light

will flash on and off slowly once.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Clean out airways indicator light

deactivated

IClean out airways indicator light

comes on when there is a heavy

build-up of fluff

(the Automatic plus indicator light will

also flash once).

2Factory default setting

(the Automatic plus indicator light will

also flash twice).

3Clean out airways indicator light

comes on when there is only a

light build-up of fluff

(the Automatic plus indicator light will

also flash three times).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Keypad tone

An audible tone sounds each time a

button is pressed.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

–The tumble dryer is switched off.

–The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

nine times.

– The Low temperature indicator light

will flash on and off slowly once and

then on and off quickly once.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Keypad tone deactivated

(factory default setting)

IKeypad tone activated

(the Automatic plus indicator light will

also flash)

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Adjusting the dryer's

electronics for very soft water

,In some areas of the UK, water is

extremely soft which can affect the

sensitivity of the control electronics.

If the dryer is installed in an area of

very soft water, you should contact

your local water supplier for

information and advice regarding

water hardness and water

conductivity. If the water

conductivity is less than 150 µS, the

following programmable function will

need to be activated.

Important. This programmable function

should not be activated if, despite the

water being extremely soft (as would be

the case if a water softener were used),

its conductivity is greater than 150 µS.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

–The tumble dryer is switched off.

–The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

ten times.

–The Low temperature indicator light

will flash on and off slowly once and

then on and off quickly twice.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Factory default setting

IAdjusted for very soft water

(the Automatic plus indicator light will

also flash)

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

Programmable functions

Extending the range of the

drying levels

You can extend the range of the

drying levels for many of the

programmes:

Machine iron+

(drier than Machine iron).

Slightly dry

(drier than Hand iron).

Normal+

(drier than Normal).

This programmable function is only

available for programmes with drying

levels.

Follow the steps (A,B,C...) to pro-

gramme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

Wait until the Start/Stop button lights up

constantly ...

C. . . and then release the Start/Stop

button.

DPress the Low temperature button

eleven times.

–The Low temperature indicator light

will flash on and off slowly once and

then on and off quickly three times.

Anumber to show which option is

selected will appear in the display

alternating with the letter P.

0Factory default setting

IDrying level range extended

(the Automatic plus indicator light will

also flash).

EPressing the Start/Stop button

switches between the options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after step D.

To select the extended drying level

^Select a programme.

^Press the drying level button

repeatedly until one or two indicator

lights come on.

–Indicator lights Extra dry and Normal

= Normal+

–Indicator lights Normal and Hand

iron = Slightly dry

–Indicator lights Hand iron and

Machine iron = Machine iron+

Programmable functions

M.-Nr. 07 847 520 / 05

Alteration rights reserved/0113

Miele T 8822 C T8822C_gb.vp User Manual To The 5dfb06d0 0b74 4f19 87c4 C6f6a4639989

Navigation menu

Versions of this User Manual:

Views

Navigation