Miele T8402C T8402c_gb User Manual To The 71f66c53 Aad3 4f7d A9e4 4042dac4196f

User Manual: Miele T8402C to the manual

Open the PDF directly: View PDF .
Page Count: 52

Contents

Operating instructions

for condenser tumble dryer

T 8402 C

To avoid the risk of accidents

or damage to the appliance

it is essential to read these

instructions before it is installed

and used for the first time. M.-Nr. 07 868 870

en-GB

Disposal of the packing

material

The transport and protective packing

has been selected from materials which

are environmentally friendly for disposal

and should be recycled.

Ensure that any plastic wrappings,

bags, etc are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation.

Disposal of your old appliance

Electrical and electronic appliances

often contain materials which, if

handled or disposed of incorrectly

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your appliance.

Please do not therefore dispose it with

your household waste.

Please dispose of it at your local

community waste recycling centre or

contact your dealer for advice. Ensure

that it presents no danger to children

while being stored for disposal.

Energy saving tips

To avoid unnecessarily long drying

times and high consumption of energy:

–Make sure that your laundry is

thoroughly spun before drying.

The higher the spin, the greater the

savings that can be made in energy

and time during drying.

–Load according to the optimum

amount of laundry recommended for

the programme being used (see

Programme chart).

Underloading is uneconomical.

Overloading gives a poorer quality of

drying and may cause unnecessary

creasing.

– Make sure the room in which the

dryer is located is well ventilated.

– Make sure the fluff filters are clean

before using the dryer.

– Check the condenser unit from time

to time and clean it when necessary.

Caring for the environment

Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Care symbols.....................................................14

Tips on drying ....................................................14

How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Brief instructions ..................................................15

Low temperature................................................16

Changing the programme sequence ..................................17

Changing a programme once it has started...........................17

Cancelling a programme once it has started and then selecting a different

programme ....................................................17

Cancelling a programme once it has started and then removing the laundry . 17

Adding or removing laundry after a programme has started ..............17

Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Emptying the condensed water container...............................20

Cleaning the fluff filters .............................................21

Cleaning them whilst dry .........................................21

Cleaning them with water .........................................22

Cleaning the tumble dryer ...........................................23

Cleaning the condenser unit .........................................24

Removing the condenser unit......................................24

Checking the condenser unit ......................................25

Cleaning the condenser unit.......................................25

Replacing the condenser unit......................................26

Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

General problems .................................................27

Check and fault messages ..........................................30

Changing the lamp ................................................31

After Sales service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Repairs..........................................................32

Future updates (PC) ...............................................32

Appliance guarantee ...............................................32

Optional accessories ...............................................32

Contents

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Front view........................................................33

Rear view ........................................................34

Installation site ....................................................34

Transporting the tumble dryer to its installation site .....................34

Building under a continous worktop / in a kitchen run ...................34

Levelling the tumble dryer ........................................35

Room in which the dryer is located .................................35

Washer-dryer stack..............................................35

Before moving the tumble dryer again (e.g. when moving house) .........35

External condensed water outlet ......................................36

Arranging the drain hose .........................................36

External drainage via a sink or gully ................................37

Installation conditions requiring a non-return valve .....................37

Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Altering the residual moisture level in the Cottons programmes..............42

Altering the residual moisture level in the Minimum iron programme ..........43

Anti-crease ......................................................44

Activating and deactivating the buzzer .................................45

Altering the standard drying level in the Automatic programme..............46

Extending the cooling down time .....................................47

Standby .........................................................48

Contents

~It is essential to read these instructions.

This tumble dryer conforms to current safety requirements.

Inappropriate use can, however, lead to personal injury and

damage to property.

To avoid the risk of accidents and damage to the tumble dryer,

please read these instructions carefully before using it for the first

time. They contain important information on its safety, installation,

use and maintenance.

Keep these instructions in a safe place and ensure that new users

are familiar with the content. Pass them on to any future owner.

Correct application

~This tumble dryer is not designed for commercial use. It is

intended for use in domestic households and similar working and

residential environments.

~The tumble dryer is not intended for outdoor use.

~It must only be used as a domestic appliance to dry items which

have been washed in a water solution and which are marked on the

manufacturer's care label as being suitable for tumble drying. If

using dry cleaning kits, do so at your own risk, and follow the

instructions provided on the packaging.

Any other usage is not supported by the manufacturer and could be

dangerous. Miele cannot be held liable for damage resulting from

incorrect or improper use or operation.

Warning and Safety instructions

~The tumble dryer can only be used by people with reduced

physical, sensory or mental capabilities, or lack of experience or

knowledge, if they are are supervised whilst using it or have been

shown how to use it in a safe way and understand the hazards

involved.

Safety with children

~Children under 8 years of age must be kept away from the tumble

dryer unless they are constantly supervised.

~Children 8 years and older may only use, clean or maintain the

tumble dryer without supervision if they have been shown how to do

so in a safe way and understand the hazards involved.

~The tumble dryer is not a toy! To prevent the risk of injury, do not

allow children to play with it or near it, or to play with the controls.

Warning and Safety instructions

Technical safety

~Before setting up the tumble dryer, check it for any externally

visible damage.

Do not install or use a damaged tumble dryer.

~Before connecting the tumble dryer, ensure that the connection

data on the data plate (voltage and frequency) match the mains

electricity supply. If in any doubt, consult a qualified electrician.

~The electrical safety of this tumble dryer can only be guaranteed

when correctly earthed. It is most important that this basic safety

requirement is observed and regularly tested, and where there is

any doubt, the household wiring system should be inspected by a

qualified electrician. Miele cannot be held liable for the

consequences of an inadequate earthing system (e.g. electric

shock).

~Do not connect the tumble dryer to the mains electricity supply by

an extension lead. Extension leads do not guarantee the required

safety of the tumble dryer (e.g. danger of overheating).

~If the electrical connection cable is faulty it must only be replaced

by a Miele approved service technician to protect the user from

danger.

~Unauthorised repairs could result in unforeseen dangers for the

user, for which Miele cannot accept liability. Repairs should only be

undertaken by a Miele approved service technician, otherwise any

subsequent damage will not be covered by the guarantee. Ensure

current is not supplied to the tumble dryer until after maintenance or

repair work has been carried out.

Warning and Safety instructions

~Faulty components must only be replaced by genuine Miele

original spare parts. Only when these parts are fitted can the safety

standards of the tumble dryer be guaranteed.

~The tumble dryer must be isolated from the electricity supply in

the event of a fault and during cleaning and maintenance.

~The tumble dryer must not be used in a non-stationary location

(e.g. on a ship).

~Do not make any alterations to the tumble dryer, unless

authorised to do so by Miele.

~In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the tumble dryer

and its surroundings in a clean condition at all times. Any damage

which may be caused by cockroaches or other vermin will not be

covered by the guarantee.

Warning and Safety instructions

Correct use

~To prevent the risk of fire, the following textiles must not be dried

in this appliance:

–items which have not been washed.

–items, such as workwear, which have not been thoroughly

cleaned and which are still soiled with grease, oil or other

deposits (such as cosmetics, lotions etc).

If items have not been thoroughly cleaned there is a danger that

these might self-ignite when heated, even after they have been

removed from the dryer at the end of the programme.

– items (e.g. mops and floor cloths) which have been treated with

inflammable cleaning agents or which contain residues of

acetone, alcohol, benzine, petrol, kerosene, stain remover,

turpentine, wax and wax remover or other chemicals.

– items which have been splashed with hair lacquer, hair spray, nail

varnish remover or similar substances.

When washing such heavily soiled items, ensure that you use

additional detergent and select a high temperature. If in doubt,

wash the items several times.

~Remove all items such as lighters and matches from pockets.

~Warning: Do not switch the tumble dryer off before the drying

programme has finished. If this is done, the laundry must be hung

up or spread out to cool it down.

Warning and Safety instructions

~Danger.

This tumble dryer must not be connected to a controllable socket

(e.g. a timer switch or a peak load shut-off device).

If the dryer programme were to be interrupted before the end of the

cooling down phase, the laundry could self-combust.

~To prevent the risk of fire, the following must not be tumble dried:

–items which have been cleaned using chemicals (e.g.

professional dry-cleaning agents).

–fabrics which contain a large proportion of rubber, foam rubber or

rubber-like materials. For example, products made from latex

foam rubber, shower caps, waterproof textiles, rubberised articles

and items of clothing and pillows with foam rubber filling.

– damaged items which contain padding or fillings (e.g. pillows,

jackets). When damaged, the filling can get out with the risk of

igniting in the dryer.

~In many programmes, the heating phase is followed by a cooling

down phase to ensure that the items are not too hot to handle when

you remove them (this also avoids the danger of the laundry

self-igniting). The programme is not finished until the cooling down

phase has been completed.

As soon as the programme has finished, remove all laundry from the

drum.

~Fabric conditioner and similar products must be used according

to the instructions on the manufacturer's packaging.

~Do not let anyone sit or lean on the door, as this can cause the

tumble dryer to tip up.

~Always close the door after use. This way you will avoid the

danger of:

–children climbing into the dryer or hiding things in it.

–pets or other small animals climbing into it.

Warning and Safety instructions

~The dryer must not be used without the fluff filters in place or if

the fluff filters are damaged in any way.

~The fluff filters must be cleaned regularly.

~The dryer must not be used without the condenser unit in place.

~The fluff filters must be thoroughly dried after cleaning. Damp or

wet filters could cause operational faults.

~Do not install the tumble dryer in a room where there is a risk of

frost occurring. At temperatures around freezing point the tumble

dryer may not be able to operate properly. There is a risk of damage

if the condensed water is allowed to freeze in the pump and in the

drain hose. The ambient room temperature should be between +2°C

and +35°C.

~If the water is drained externally instead of being collected in the

condensed water container, make sure the drain hose is securely

attached if you hang it in a sink or basin to avoid the hose slipping

and the water causing damage.

~Condensed water is not drinking water.

It can cause health problems in both people and animals.

~Always keep the area around the tumble dryer free of dust and

fluff. Dust drawn into the tumble dryer can cause blockages in the

condenser unit over time.

~The tumble dryer must not be hosed down.

Warning and Safety instructions

Accessories

~Only use genuine Miele original spare parts and accessories with

this tumble dryer.

If non-Miele parts are used, guarantee, performance and product

liability claims may be invalidated.

Miele cannot be held liable for damage caused by

non-compliance with these Warning and Safety instructions.

Warning and Safety instructions

aProgramme selector

The programme selector can be

turned clockwise or anti-clockwise.

bProgramme sequence and check

lamps

cStart button

Press the Start button to start a

programme.

The Start indicator lamp will flash as

soon as a programme can be

started. It lights up constantly once

the programme has started.

dI-On/0-Off button

To switch the appliance on or off / to

interrupt a programme.

The Finish/Anti-crease lamp will light

up as confirmation that the tumble

dryer has been switched on.

eDoor Button

To open the door / to cancel a

programme.

Pressing this button will open the

door even when the appliance is

switched off at the mains.

If the appliance is switched on at the

mains and the door is opened the

drum lighting will come on. It will go

out a few minutes later to save

energy.

Control panel

Care symbols

Before drying check the drying symbol

on the care label. If there are no

symbols, dry at your own risk!

q.........Dryatnormal temperature

r..........Dryatalowtemperature

s...............Donottumble dry

–For delicates and fabrics with the

following care label rselect Low

temperature.

Tips on drying

– Always observe the maximum

recommended loads given in the

"Programme chart". Never overload

the drum.

Overloading can cause unnecessary

wear and tear to the laundry, give a

disappointing drying result and

cause more creasing.

– Do not put soaking wet items into the

tumble dryer. Spin them thoroughly

after washing using the appropriate

spin speed.

–Use the Automatic programme for

drying mixed loads of cottons and

minimum iron fabrics.

–Open jackets so that they can dry

evenly.

–Woollens and wool blends tend to

become matted and shrink if dried in

a tumble dryer. They can, however,

be partially dried using the Woollens

handcare programme.

–Down-filled garments have linings

which have a tendency to shrink,

depending on the quality of the item.

They can be partially dried using the

Smoothing programme.

–Pure linen should only be machine

dried if specified as suitable by the

manufacturer on the care label, as

the surface of the fabric may

otherwise become rough. It can be

partially dried using the Smoothing

programme.

–Loopknit garments (e.g. T-shirts and

underwear) tend to shrink depending

on their quality. Do not over-dry

these textiles. When purchasing

these garments it is advisable to take

their shrinkage properties into

account.

– Minimum iron fabrics tend to crease

more, the greater the load. This is

also the case for garments made

from very fine weave fabrics, such as

shirts or blouses.

If in doubt, reduce the load or use

the Minimum iron - Hand iron

programme.

–Starched laundry can be dried in the

tumble dryer. To achieve the usual

finish, double the amount of starch

should be used.

–New dark coloured garments should

be washed and dried separately

from light coloured garments to avoid

the danger of colours running and

discolouring other garments or even

plastic components in the appliance.

Dark coloured fibres can also settle

on light coloured garments and vice

versa.

Notes on laundry care

Brief instructions

The headings numbered (A,B,C...)

show the operating sequence and can

be used as a brief guide to using your

dryer.

ASort the laundry

To ensure an even drying result

separate the washed laundry and sort it

according to:

. . . the drying level required

. . . the type of fibre or weave

. . . size

. . . the moisture content after spinning.

,Make sure that objects e.g.

detergent dispensing balls have

been removed from the laundry.

They could melt, and cause damage

to the dryer or the laundry.

– Check seams and stitching to ensure

that padding and linings are intact.

– Fasten duvet covers and pillow

cases to prevent small items from

being trapped inside them.

–Fasten hooks and eyes etc.

–Tie fabric belts and apron strings.

–Sew in or remove underwiring from

bras.

BTurn on the tumble dryer

^Switch the dryer on by pressing the

jk button.

The tumble dryer may be switched on

after loading, saving energy as the

lighting will not come on.

CLoad the tumble dryer

^Press the Door button to open the

door.

^Load the laundry loosely into the

drum.

Do not overload the drum. See the

"Programme chart" for

recommended loads for each

programme.

Overloading can cause unnecessary

wear and tear to the laundry and

give a disappointing drying result.

^Before closing the door make sure

the fluff filter is correctly positioned.

Check the laundry is right inside the

drum so that it cannot get trapped or

damaged when the door is shut.

^Shut the door either with a gentle

swing, or lean against it and push it

shut.

How to dry correctly

DSelect a programme

^Turn the programme selector to the

required programme.

Low temperature

^For drying particularly sensitive

fabrics (care symbol r) e.g. acrylics

turn the programme selector to the

Low temperature position.

Because the heater rating is reduced

for the Low temperature setting, clothes

dry more slowly thus lengthening drying

times.

EStart the programme

^Press the Start button.

The indicator lamp for the Start button

will then change from flashing to being

on constantly.

The drying cycle begins.

Depending on the programme

selected, the drying stage reached is

shown by the sequence indicator lamps

on the right hand side of the control

panel.

Before the end of a programme

The cooling down phase takes place

before the end of a programme so that

the garments are not too hot to handle

(the Cool air indicator lamp will come

on). The programme is not finished until

the cooling down phase is complete.

The Woollens handcare and Smoothing

programmes do not include a cooling

down phase.

At the end of a programme

The Finish/Anti-crease indicator lamp

comes on.

The drum will continue to rotate at

intervals to prevent laundry creasing, if

you do not wish to remove it immediate-

ly. The anti-crease phase lasts for an

hour. There is no anti-crease phase on

the Woollens handcare programme.

During the anti-crease phase...

. . . (depending on the programme

selected) the indicator lamp for the

drying stage reached will also light up.

. . . the buzzer will sound at intervals.

How to dry correctly

FRemove the laundry

^Press the Door button.

^Open the door.

^Remove the laundry.

Check that all items have been

removed from the drum. If items are

left in the dryer, they could be

damaged by overdrying when the

dryer is next used.

^Switch the dryer off by pressing the

l-On/0-Off button.

^Clean the fluff filters.

^Close the door.

^Empty the condensed water

container (unless the dryer has been

connected for external drainage).

^The condenser unit should be

checked and cleaned on a regular

basis (see "Cleaning and care").

Changing the programme

sequence

Changing a programme once it has

started

You cannot change to another

programme once a programme has

started (this prevents unintentional

alterations).

If you try and change a programme the

Finish/Anti-crease light will start

flashing.

You will need to cancel the current

programme before you can select a

new one.

Cancelling a programme once it has

started and then selecting a different

programme

^Turn the programme selector to

Finish.

^Press the Door button.

^Close the door.

^Select another programme and start

it.

Cancelling a programme once it has

started and then removing the

laundry

^Proceed as described in "Adding or

removing laundry after a programme

has started" below.

^Switch the dryer off after closing the

door.

Adding or removing laundry after a

programme has started

^Press the Door button.

^Open the door.

,Danger of burning:

Do not touch the back of the drum

when adding or removing items. The

drum and the items can get very hot.

^Add or remove items as required.

^Close the door.

^Press the Start button.

How to dry correctly

Cottons Max. load: 6 kg*

Normal+, Normal**, Low temperature

Fabric type Single and multi-layered cottons fabrics such as towelling,

jerseywear, underwear, flannelette bed linen.

Note –Select Low temperature for fabrics with the rsymbol. Laundry

is dried at a lower temperature.

Hand iron, Machine iron

Fabric type Cottons and linen fabrics, e.g. table linen, bedlinen, starched

laundry.

Note To prevent laundry from drying out it should be rolled up until you

are ready for ironing.

Minimum iron Max. load: 3 kg*

Normal, Low temperature, Hand iron

Fabric type Minimum iron items made of cotton, synthetic or blended fabrics,

e.g. shirts, blouses, skirts and table cloths.

Notes – Select Low temperature for fabrics with the rsymbol (e.g.

acrylic garments). Laundry is dried at a lower temperature.

– Select Hand iron for delicate fabrics and to reduce creasing

even more, reduce the load to 1.5 kg*.

– In the Minimum iron Hand iron programme, items are dried with

very little creasing, depending on fabric type and amount of

load.

* Weight of dry laundry

** Note for test institutes:

Test programme in accordance with Regulation 392/2012/EU for energy

labelling measured in accordance with EN 61121

Programme chart

Automatic Max. load: 3.5 kg*

Fabric type Mixed load of garments suitable for Cottons and Minimum iron

programmes.

Timed drying Max. load: 6 kg*

Warm air

Fabric type –Multi-layered fabrics whose layers have different drying

characteristics, e.g. jackets, pillows.

–For drying individual items, e.g. bath towels, swimwear,

tea-towels.

Cool air

Fabric type Any item which only needs airing.

Woollens handcare Max. load: 2 kg*

Fabric type Woollen fabrics

Notes – To refresh and fluff up woollen garments quickly. Woollen

fabrics are not dried completely by this programme.

– Remove garments as soon as the programme has finished and

leave to finish drying at room temperature.

Smoothing Max. load: 3 kg*

Fabric type – Cottons and linen fabrics.

– Minimum iron mixed fibre, cotton or synthetic items, e.g.

trousers, jackets, shirts.

Notes – Smooths out creasing caused during the spin cycle in the

washing machine.

–Fabrics are not completely dried in this programme. Remove

garments as soon as the programme has finished and leave to

finish drying at room temperature.

* Weight of dry laundry

Programme chart

Emptying the condensed water

container

The condensed water will be collected

in the condensed water container

unless the tumble dryer has been fitted

with a drain hose (see installation).

The condensed water container

should be emptied after every

drying cycle or as soon as the

Empty out container indicator lamp

comes on.

The drying programme will be

interrupted if the maximum level of the

condensed water container is reached.

The Empty out container indicator lamp

comes on and the buzzer sounds.

^Grip the container firmly with both

hands, as shown, and pull it out

slightly towards the right-hand side.

^Hold the container with both hands

and carry it in a horizontal position.

^Open the shutter and empty out the

water.

^To replace the container hold it at a

slight angle (as when removing it)

and push it in gently until you feel it

click into position.

^Before starting a new programme,

first switch the tumble dryer off and

then on again. The Empty out

container indicator lamp will go out.

Condensed water should not be

consumed. It could lead to health

problems for people and animals.

Condensed water can be put to

household use (e.g. used in a steam

iron or humidifier). To ensure that any

residual particles of fluff in the

condensed water are removed before

use, pass it through a fine sieve or

paper filter first.

Cleaning and care

Cleaning the fluff filters

The fluff which is created by the drying

process is collected by the fluff filters in

the door and the door opening. Clean

the filters after each drying programme.

Cleaning them whilst dry

Tip: You can also use a vacuum

cleaner.

^Open the door and pull the fluff filter

(1) out of the door as illustrated.

^Use your fingers to remove the fluff

from the surface of the filter.

^Remove any fluff from the hollow part

of the door holder. A cleaning brush

is available as an optional extra from

Miele or use a vacuum cleaner.

^Once clean, push the filter back into

the door holder until it clicks into

position. Ensure it is facing the

correct way.

^Also clean the door seal (2) with a

damp cloth.

^Use your fingers to remove the fluff

from the two fluff filters in the door

opening.

^Close the door.

Cleaning and care

Cleaning them with water

If there is a great deal of compacted

fluff on any of the filters, they can be

removed and cleaned under hot

running water.

^Open the door and pull the fluff filter

out of the door as described

previously.

The two filters in the door opening can

also be removed if you need to clean

them with water.

^Turn dial aand pull the filter by the

dial out of the door opening as shown

b. Do the same on the other side.

^Rinse all the filters under hot, running

water.

^Then shake the filters until no more

water droplets are visible.

^Dry the filters thoroughly with care.

^Clean the area underneath these

filters, e.g. with a vacuum cleaner.

,Do not replace them if they are

damp or wet. Damp or wet filters

could cause operational faults.

^Push the large filter back into the

door holder until it clicks into position.

Ensure it is facing the correct way.

^Replace the filters in the door

opening by first inserting them at the

bottom and then pressing them into

place at the top.

^Lock both dials.

Cleaning and care

Cleaning the tumble dryer

Disconnect the tumble dryer from

the mains electricity supply.

Miele branded cleaning and

conditioning products are available to

order via the internet on

www.miele-shop.com.

^Clean the housing and control panel

with a slightly damp cloth and a mild

detergent or soapy water.

^The drum and other stainless steel

parts can be cleaned with a suitable

stainless steel cleaner following the

manufacturer's instructions.

Do not use solvents, abrasive

cleaners, glass cleaners or

all-purpose cleaners. These could

damage plastic sufaces and other

parts.

^Dry all parts with a soft cloth.

Cleaning and care

Cleaning the condenser unit

Detergent residue, hair and fine fluff

from the dryer can get through the fluff

filters and block the condenser unit.

Dust from the room in which the dryer is

installed can also get into the

condenser unit and cause a blockage.

Check the condenser unit at least

once a year. If the dryer is used

frequently then clean the condenser

unit on a regular basis.

Removing the condenser unit

^Use the yellow lever supplied to open

the service panel.

^Insert the lever into the middle of the

gap at the top (see arrow)

^Now remove the panel by pulling it

diagonally upwards. Then place it to

one side.

^Turn the lever on the inner cover

downwards to the vertical position.

^Pull the cover forwards

^Then remove it by pulling it

diagonally upwards.

^Turn the lever on the condenser unit

to the vertical position so that the

hook on the lever is no longer in the

groove at the bottom of the

condenser unit housing.

Cleaning and care

^Pull the condenser unit out of its

housing by the handle.

Checking the condenser unit

^Hold the condenser unit up to the

light as shown.

^Check to see if there is any fluff

inside it.

The arrows in the illustration above

indicate where to look.

If you cannot see any fluff:

^Replace the condenser unit (see

following page).

If you can see some fluff:

^Clean the condenser unit as

described below.

Cleaning the condenser unit

^When rinsing the condenser unit,

make sure you position it as

shown in the next two illustrations.

^Use a shower head or similar to rinse

the unit out as shown.

Cleaning and care

^Then flush the unit through from the

front.

^Check the condenser unit again for

any visible fluff and if necessary flush

it through again until it has all gone.

^Repeat as required.

^Also make sure the rubber seals are

clean.

The rubber seals must not be

removed and must be free of kinks.

^Shake the water off the condenser

unit until no more droplets of water

are visible.

Checking and cleaning the

condenser unit housing

^Remove any soiling still visible inside

the housing unit by hand using a

damp cloth. Do not try and access

areas you cannot reach by hand!

Replacing the condenser unit

^With the handle facing upwards,

push the condenser unit back into

position in its housing.

^Turn the lever down to the horizontal

position, making sure that the hook

on the lever clicks into the groove.

When replacing the inner cover after

cleaning, ensure that the rubber seal

fits correctly into the groove.

^Replace the inner cover making sure

the hooks locate correctly. Hold it at

an angle and push it gently

downwards.

^Then turn the lever upwards into the

horizontal position to lock the cover.

^Replace the service panel and press

the upper edge until it clicks into

position.

,It is important to ensure that both

the condenser unit and the cover

are correctly positioned and locked,

otherwise water may leak from the

dryer.

Cleaning and care

With the help of the following notes minor faults in the performance of the

appliance, some of which may result from incorrect operation, can be put right

without contacting the Service Department.

,Repair work to electrical appliances should only be carried out by a

suitably qualified person in strict accordance with current local and national

safety regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

General problems

Problem Possible cause Remedy

The programme does

not start.

No obvious cause. –Is the dryer switched

on?

– Is the plug correctly

inserted into the socket

and switched on?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

Power cut. A programme which was running previously will

continue automatically when power is restored to the

tumble dryer as long as the Cooling down phase had

not been reached.

Items made of synthetic

fibres are charged with

static electricity after

drying.

Synthetic fibres tend to

attract static charge.

Static charge can be

reduced by adding a

fabric conditioner to the

final rinse in the washing

programme or a fabric

conditioner sheet to the

load when drying.

The Start button

indicator light flashes

slowly.

The dryer is in Standby

mode.

This is quite normal and

not indicative of any fault.

See "Programmable

functions".

Problem solving guide

Problem Possible cause Remedy

There is a build-up of

fluff.

Fluff is principally the result

of friction when garments

are being worn and

washed. Machine drying

hardly causes any fluff to

form and has been

established by research

institutes to have no

appreciable effect on the

lifetime of fabric.

Fluff is collected by the fluff

filters and can be easily

removed (see "Cleaning

and care").

The laundry is not

sufficiently dry.

The load consisted of

different fabric.

–Finish drying using the

Warm air programme.

–Select a more suitable

drying programme next

time* (see "Programme

chart").

Water leaks from the

tumble dryer after the

condenser unit has

been cleaned.

– The inner cover of the

condenser unit has not

been locked properly

and/or the condenser

unit has not been

positioned correctly.

– Fluff has collected in the

condenser unit housing.

– Ensure that the

condenser unit is

positioned correctly and

lock the inner cover.

– Check the rubber seals.

– Use a cloth to remove

any visible fluff from the

inside of the condenser

unit housing.

The interior drum

lighting does not

come on.

The lighting switches off

automatically (to save

energy).

Switch the dryer off and

then on again.

The light needs changing. Change the light as

described at the end of this

section.

* You can alter the residual moisture levels for some programmes. See

"Programmable functions" at the end of this booklet.

Problem solving guide

Problem Possible cause Remedy

Drying is

taking too long,

or the

programme

has been

cancelled

The dryer is not working

efficiently or economically*.

The most likely cause is a

build-up of fluff, hair or

detergent residue on the fluff

filters.

–Remove any fluff, hair or

residual detergent.

–Rinse the filters if necessary

and then dry them

thoroughly before replacing

them.

If not thoroughly dry faults

will occur.

–If the above measures do

not remedy the problem

follow the advice below.

Ventilation to and from the

dryer may be insufficient (e.g

because it is installed in a

small room). This has caused

the temperature in the room to

rise sharply.

–Open a door or window

while the tumble dryer is in

operation for increased air

flow.

The vents below the door are

blocked.

– Remove any objects that

are blocking the vents.

Detergent residue, hair and

fine fibres can block the

condenser unit.

– Check the condenser unit

from time to time and clean

it if necessary (see

"Cleaning and Care").

The laundry has not been

spun sufficiently.

–Make sure that your laundry

is thoroughly spun at the

appropriate spin speed.

The tumble dryer has been

overloaded.

–Do not exceed the

maximum load for the

programme selected.

Metallic components, e.g. zips

have prevented the dryer from

registering the correct

moisture level in the laundry.

–Open zips next time.

–If the problem occurs again,

dry garments with long zips

using "Warm air" (timed

drying).

* Before attempting to remedy the problem:

–Open and close the door.

–Switch the dryer off and then on again to start a programme.

Problem solving guide

Check and fault messages

Problem Possible cause Remedy

The Empty container

indicator light comes

on.

The condensed water

container is full or there is

kink in the drain hose.

–Empty the condensed

water container.

–Check the drain hose.

–The indicator light will

go out if you open and

close the door.

The programme stops

and the Machine iron

or Hand iron indicator

light flashes.

The buzzer sounds.

No obvious cause. –Switch the dryer off and

then on again.

–Then start the

programme again.

If the programme stops

again and the indicator

light flashes again there is

a fault. Contact the Miele

Service Department.

The Finish/

Anti-crease indicator

light flashes while

drying is in progress.

The programme selector

was moved after the start of

a programme. The

programme continues to

run as normal.

Turn the selector back to

the original position and

the indicator light will go

out.

The programme stops

and the Finish/

Anti-crease indicator

light comes on.

The buzzer sounds.

This is not a fault.

The electronic unit has

recognised that there is not

enough laundry in the drum

and cancelled the

programme.

Drying items which are

already dry can also cause

the programme to be

cancelled.

Use the Warm air

programme (timed drying)

to dry individual items.

Before changing a

programme: Open and

close the door.

The Cooling down

indicator light comes

on. The buzzer

sounds.

The dryer is not working

efficiently or economically.

See the previous page

under "Drying is taking

too long ...".

Problem solving guide

Changing the lamp

Disconnect the tumble dryer from

the mains electricity supply.

^Open the door.

You will find the interior light cover at

the top of the drum aperture.

^Insert a suitable tool, such as a wide

bladed screwdriver, under the side

edge of the light cover as illustrated.

^Apply a little pressure and whilst

doing so turn your wrist in the

direction of the arrow to open the

cover.

The cover will open downwards.

The temperature resistant lamp should

only be ordered from your Miele Dealer

or the Miele Spare Parts Department.

The light specification and maximum

wattage is stated on the data plate

and on the light cover.

^Turn the light anti-clockwise to

remove.

^Replace the lamp.

^To close the cover push it upwards

and press it on the left and right until

you hear it click into position.

,Ensure that it is fitted into

position securely, as any moisture

could cause a short circuit.

Problem solving guide

Repairs

In the event of any faults which you

cannot remedy yourself, please contact

–your Miele dealer or

–the Miele Service Department (see

back cover for contact details).

When contacting your dealer or the

Service Department, please quote the

model and serial number of your

appliance, both of which are shown on

the data plate. This is visible when you

open the door.

N.B. A call-out charge will be

applied for service visits where the

problem could have been resolved

as described in these instructions.

Future updates (PC)

The indicator or check light marked PC

on the fascia panel is the interface used

by the Miele service technicians during

service work for testing purposes and

for updating the appliance's

programme data.

Appliance guarantee

In the U.K. your appliance is

guaranteed for 2 years from the date of

purchase. However you must activate

your cover by calling 0845 365 6640 or

registering online at www. miele.co.uk.

For information on the appliance

guarantee specific to your country

please contact Miele. See back cover

for contact details.

Optional accessories

Optional accessories for this dryer are

available from your Miele Dealer, the

Miele Spare Parts Department or via the

internet at www.miele-shop.com.

Please note that telephone calls may

be monitored and recorded for

training purposes.

After Sales service

Front view

aMains connection cable

bCondensed water container

cControl panel

dDoor

eService panel for condenser unit

fFour height-adjustable screw feet

gExternal drainage options (e.g. via

wash basin, wash basin drain outlet,

or gully. See "External condensed

water outlet").

Installation

Rear view

aProtruding lid for holding when

moving the appliance (see arrows)

bAir inlet vent for cooling the

condenser unit

cMains connection cable

dExternal drainage of the condensed

water

eAccessories for connection to a sink

drain outlet

Installation site

,Make sure the dryer door can be

opened without hindrance after

installation.

Transporting the tumble dryer to its

installation site

When moving the appliance, you can

hold it by the lid where it protrudes to

the rear of the dryer. To manoeuvre the

dryer out of its packing case to its

installation site hold it by the front feet

and at the back of the lid. Do not lift

the appliance by the drum door.

Building under a continous worktop /

in a kitchen run

,Abuilding-under kit* with a

coverplate to replace the appliance

lid is required. It must be fitted by a

suitably qualified person to ensure

electrical safety.

N.B. If you wish to push your appliance

under a worktop and there is space to

do this without removing the lid the

building under kit is not necessary.

Otherwise the building under kit is

essential.

– The building-under kit is supplied

with its own installation instructions.

– N.B. When built under drying times

may be longer.

– The electrical socket must be

located in an accessible position

near the tumble dryer.

With niche heights of:

–830-840 mm, longer screw feet* are

required.

–870-885 / 915-930 mm, one or two

raising kits* are required.

* accessory available to order.

Replacing the lid

If the lid has been removed in order to

fit a coverplate, ensure that, if the lid is

ever replaced, it fits securely into the

rear holders. Otherwise, it is not

properly secure for transport.

Installation

Levelling the tumble dryer

The appliance must be perfectly level

to ensure safe and proper operation.

^The screw feet can be adjusted to

compensate for any unevenness in

the floor.

,The air inlet and outlet vents on

the front of the tumble dryer must

not be covered as this would

prevent sufficient ventilation for

cooling the condenser unit.

,Do not block the gap between

the bottom of the tumble dryer and

the floor with plinth facings, deep

pile carpet etc. This would hinder a

sufficient flow of air to the dryer.

Room in which the dryer is located

Air taken in for the drying process will

be warm when it is expelled from the

front of the dryer. This expelled air

heats up the air in the room. It is

therefore very important to ensure that

the room is adequately ventilated,

particularly if the dryer is located in a

small room. Otherwise drying durations

may be longer.

Washer-dryer stack

The tumble dryer can also be combined

with a Miele washing machine in a

washer-dryer stack. The appropriate

"WTV" stacking kit (available to order) to

match your dryer is required.

,Stacking kits must only be

installed by a suitably qualified fitter.

Before moving the tumble dryer

again (e.g. when moving house)

After each use a small quantity of

condensed water will collect in the area

around the pump. This water can run out

if the tumble dryer is tipped up when it is

being moved. It is a good idea to run the

Cool air programme for approximately 1

minute before moving the tumble dryer.

Any remaining condensed water will then

be fed into the condensed water

container or out through the drain hose.

Installation

External condensed water

outlet

General notes

When drying is in progress, condensed

water is pumped into the condensed

water container through the drain hose at

the back of the dryer. The condensed

water can also be drained off directly if

the tumble dryer is installed near a sink,

drain outlet etc. so that the condensed

water container does not have to be

emptied.

Drain hose length ............1.50 m

Maximum delivery head .......1.50 m

Maximum drain hose length ....4.00 m

,If the on-site water drainage

system is not fitted with a non-return

valve or an appropriate air gap, one

must be fitted to prevent the risk of

back-flow. (See "Installation conditions

requiring a non-return valve").

The following optional accessories are

available:

–an extension hose

–a non-return valve kit for connection

to an external condensed water

outlet (includes an extension hose).

Maximum delivery head with

non-return valve fitted: 1.00 m

Arranging the drain hose

,Do not pull on the drain hose and

do not stretch it or allow it to become

kinked as it could get damaged.

^There will be a small amount of

residual water in the drain hose.

Have a container ready to collect

this.

^Pull the hose off its connection (see

arrow).

^Allow any residual water to run into

the container.

^Unwind the hose and pull it carefully

out of the holders.

^Position the hose to the right or left

hand side as necessary.

Leave the hose in the middle holder to

prevent it from becoming kinked

inadvertently.

Installation

External drainage via a sink or gully

^See "Front view" illustration.

,If you want to drain the water off

into a sink you will need to secure

the hose carefully, e.g. by tying it to

a tap to make sure it cannot slip

during use. Otherwise there is a risk

of overflowing water which could

cause damage.

^Use the bow-shaped guide to

prevent the drain hose from

becoming kinked.

Installation conditions requiring a

non-return valve

,Certain installation conditions

require the fitting of a non-return

valve for external water

connection (available as an

optional accessory). A non-return

valve will prevent the risk of

back-flow out of the dryer which

could cause damage.

A non-return valve is required:

–If the tumble dryer is connected to a

sink drain outlet (see the following

section).

–If the tumble dryer is connected to a

drainage system already in use by

another appliance, e.g. a dishwasher

or washing machine.

Example: Connection to a sink drain

outlet

The drain hose with non-return valve

fitted can be connected directly to a

suitable sink drain outlet.

^Remove the following from the back

of the dryer at the top:

Adapter 1and hose clip 3behind it.

Installation

1 Adapter

2 Nut

3 Hose clip

4 End of the hose

5 Non-return valve

6 Tumble dryer drain hose

^Fit adapter 1to the sink drain outlet

using nut 2.

If this nut has a flat disc in it you

should take the disc out first.

^Attach the end of hose 4to adapter

^Use a screwdriver to tighten hose

clip 3up close to the nut.

,Non-return valve 5has to be

fitted with the arrow pointing in the

direction of flow (i.e. towards the

sink). Otherwise water will not drain

out of the appliance.

^Fit non-return valve 5to tumble dryer

drain hose 6(make sure it is fitted in

the correct direction - see arrow on

non-return valve).

^Secure the non-return valve using

hose clips.

Installation

Programme Load Final spin speed in a domestic

washing machine

Energy Time

kg* rpm kWh Minutes

Cottons Normal 6.0 1000 (60 % residual moisture)**

1200 (53 % residual moisture)

1400 (50 % residual moisture)

1600 (48 % residual moisture)

1800 (43 % residual moisture)

3.30

3.00

2.85

2.55

2.50

Cottons Hand iron 6.0 1000 (60 % residual moisture)

1200 (53 % residual moisture)

1400 (50 % residual moisture)

1600 (48 % residual moisture)

1800 (43 % residual moisture)

2.65

2.35

2.20

1.85

1.80

Minimum iron Normal 3.0 1200 (40 % residual moisture) 1.20 37

Minimum iron Hand iron 3.0 1200 (40 % residual moisture) 1.00 32

Automatic 3.5 800 (60 % residual moisture) 2.10 85

Woollens handcare 2.0 1000 (60 % residual moisture) 0.15 4

Smoothing 3.0 1000 (60 % residual moisture) 0.30 8

* Weight of dry laundry

** Test programme in accordance with Regulation 392/2012/EU for energy labelling measured in

accordance with EN 61121

All data without a "star" against it was calculated using EN 61121

Before testing in accordance with EN 61121, drya3kgload of cotton laundry with 70% residual

moisture as per the above standard using the Cottons Normal programme.

Consumption data can vary from the nominal values given above depending on the size of the

load, type of textiles, residual moisture levels after spinning and fluctuations in the electricity

supply.

Consumption data

Height 850 mm

Width 595 mm

Depth 587 mm

Depth with door open 1062 mm

Height for building under 820 mm

Width for building under 600 mm

Depth for building under 600 mm

Suitable for pushing under a worktop Yes

Suitable for stacking Yes

Weight 51 kg

Drum volume 111 litres

Maximum capacity 6 kg dry weight

Capacity of condensed water container approx. 3.5 litres

Drain hose length 1.5 m

Maximum delivery head 1.5 m

Maximum drain hose length 4 m

Length of connection cable 2 m

Voltage see data plate

Connected load see data plate

Fuse rating see data plate / plug

Lamp wattage see data plate

Energy consumption see "Consumption data"

Test certificates awarded see data plate

Technical data

Programmable functions

for changing default settings

The programmable functions are

used to alter the tumble dryer´s

electronics to suit changing

requirements.

Programmable functions can be

altered at any time.

Altering the residual moisture

level in the Cottons

programmes

The tumble dryer is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier or damper, you can increase

or reduce the default residual

moisture in the Cottons programmes.

Follow the steps (A,B,C...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator lamp

lights up constantly...

D. . . and then release the Start button.

The Cool air lamp will flash once.

The flashing sequence of the

Drying lamp shows which option is

currently selected.

–If the Drying lamp is not flashing:

the residual moisture level will be

increased and laundry will be

damper.

–If the Drying lamp flashes once: the

residual moisture level will remain

on the standard setting (factory

default setting).

– If the Drying lamp flashes twice:

the residual moisture level will be

reduced and laundry will be drier.

EPressing the Start button switches

between the 3 options.

FSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato D.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Altering the residual moisture

level in the Minimum iron

programme

The tumble dryer is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier or damper, you can reduce

or increase the default residual

moisture in the Minimum iron

programme.

Follow the steps (A,B,C...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator lamp

lights up constantly...

D. . . and then release the Start button.

ETurn the programme selector to

Cottons Normal+.

The Cool air lamp will flash twice.

The flashing sequence of the

Drying lamp shows which option is

currently selected.

–If the Drying lamp is not flashing:

the residual moisture level will be

increased and laundry will be

damper.

–If the Drying lamp flashes once: the

residual moisture level will remain

on the standard setting (factory

default setting).

– If the Drying lamp flashes twice:

the residual moisture level will be

reduced and laundry will be drier.

FPressing the Start button switches

between the 3 options.

GSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato E.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Anti-crease

If laundry is not removed as soon as

the programme has finished, the

drum will continue to rotate at

intervals for two hours to prevent

creasing.

The anti-crease function

–is activated when the tumble dryer is

delivered. You can shorten the

duration of the anti-crease phase or

deactivate it if wished.

–is used in all programmes except

Woollens handcare.

– should be left activated.

Follow the steps (A,B,C...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

–The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator lamp

lights up constantly...

D. . . and then release the Start button.

ETurn the programme selector to

Cottons Normal.

The Cool air lamp will flash three times.

The flashing sequence of the

Drying lamp shows which option is

currently selected.

–If the Drying lamp is not flashing:

Anti-crease is deactivated

–If the Drying lamp flashes once:

Anti-crease will last for 1 hour

–If the Drying lamp flashes twice:

Anti-crease will last for 2 hours

(factory default setting).

FPressing the Start button switches

between the 3 options.

GSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato E.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Activating and deactivating the

buzzer

A buzzer sounds (at intervals for a

maximum of 1 hour) to let you know

the programme has finished.

The tumble dryer is delivered with the

buzzer activated but you can

deactivate it if wished.

If there is a fault, a continuous tone will

sound even if the buzzer has been

deactivated.

Follow the steps (A,B,C...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator lamp

lights up constantly...

D. . . and then release the Start button.

ETurn the programme selector to

Cottons Low temperature.

The Cool air lamp will flash four times.

The flashing sequence of the

Drying lamp shows which option is

currently selected.

–If the Drying lamp is not flashing:

the buzzer is deactivated

–If the Drying lamp is flashing:

the buzzer is activated (factory

default setting).

FPressing the Start button switches

between the 2 options.

GSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato E.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Altering the standard drying

level in the Automatic

programme

The drying level for this programme

is set at a standard Normal level.

You have the option of changing this

to an increased Normal+ (drier than

Normal)ortoHand iron (damper than

Normal) drying level.

Follow the steps (A,B,C...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator lamp

lights up constantly...

D. . . and then release the Start button.

ETurn the programme selector to

Machine iron.

The Cool air lamp will flash six times.

The flashing sequence of the

Drying lamp shows which option is

currently selected.

–If the Drying lamp is not flashing:

the standard drying level is Hand

iron

–If the Drying lamp flashes once: the

standard drying level will remain

on the Normal setting (factory

default setting).

– If the Drying lamp flashes twice:

the standard drying level is

Normal+.

FPressing the Start button switches

between the 3 options.

GSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato E.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Extending the cooling down

time

The cooling down phase which takes

place before the end of a programme

can be lengthened if required. This

makes the garments easier to handle.

The dryer is delivered with the

extended cooling down time option

deactivated. You can extend the

cooling down time by 5 minutes or 10

minutes.

The option of extending the cooling

down time is available with the Cottons,

Minimum iron and Automatic

programmes.

Follow the steps (A,B,C...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

–The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator lamp

lights up constantly...

D. . . and then release the Start button.

ETurn the programme selector to

Smoothing.

The Cool air lamp will flash seven times.

The flashing sequence of the

Drying lamp shows which option is

currently selected.

–If the Drying indicator lamp is not

flashing: the cooling down time is

not extended (factory default

setting).

–If the Drying lamp flashes once:

the cooling down time will be

extended by five minutes.

– If the Drying lamp flashes twice:

the cooling down time will be

extended by ten minutes.

FPressing the Start button switches

between the 3 options.

GSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato E.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Standby

To save energy, the programme

sequence/check lights go out and

the indicator light for the Start button

starts flashing slowly.

To come out of standby mode

^Turn the programme selector or

press the Start button. Neither will

have any effect if a programme is

running.

The standby function is activated and

the programme sequence/check lights

will go out after 10 minutes:

– if a programme is not selected after

the dryer has been switched on.

– after a programme has started.

They will, however, come on for 10

minutes at the end of the programme or

the end of the anti-crease phase. The

buzzer (if selected ) will sound for 10

minutes at the end of the programme.

Factory default. Not in current

programme

As described under "On" above.

However, they will stay on after the

programme has started and remain

visible during the programme.

Off

The programme sequence/check lights

will stay on while the dryer is switched

on.

Follow the steps (A,B,C...) to

programme and store in memory.

^See next page.

Programmable functions

Before you begin, ensure that:

–The tumble dryer is switched off.

–The door is closed.

–The programme selector is at Finish.

APress the Start button and keep it

pressed in whilst carrying out steps

B-C.

BSwitch the dryer on.

CWait until the Start indicator light

lights up constantly...

D. . . and then release the Start button.

ETurn the programme selector to

Woollens handcare.

The Cooling down light will flash eight

times.

The flashing sequence of the

Drying light shows which option is

currently selected.

–If the Drying light is not flashing:

On has been selected.

–If the Drying light flashes once:

Factory default. Not in current

programme has been selected.

– If the Drying light flashes twice:

Off has been selected.

FPressing the Start button switches

between the 3 options.

GSwitch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:

^Carry out steps Ato E.

^Switch the dryer off after checking

the setting as described above.

Programmable functions

Alteration rights reserved/4512 M.-Nr. 07 868 870 / 03

Miele T8402C T8402c_gb User Manual To The 71f66c53 Aad3 4f7d A9e4 4042dac4196f

Navigation menu

Versions of this User Manual:

Views

Navigation