Mikrotikls SIA LHG5ND Unlicensed National Information Infrastructure TX User Manual

Mikrotikls SIA Unlicensed National Information Infrastructure TX

User Manual

LHG seriesQuick Setup Guide and Warranty InformationThe LHG is a outdoor wireless system with a built in antenna. It can be used as a CPE or for Point to Point links. AssemblyAttach the two legs to the LHG case, then snap the assembed LHG unit to the grid in the appropriate locations. Fixthe legs in place with two self thread screws (Included, use philips screw driver PH2). The package also contains agrounding cable connector, and a 5 degree angle adapter. More detailed instructions available on the product pageon http://routerboard.com Connecting1. Open the Ethernet door to connect your PC or LAN cable to the Ethernet port, connect the other end of theEthernet cable to a PoE injector2. Set LAN computer IP configuration to automatic (DHCP)3. Default IP address of the unit is 192.168.88.1, open this address in your web browser to start configuration.The username is admin and there is no passwordPoweringThe device accepts powering only from Passive PoE injectorsBooting processInitial  connection  has  to  be  done  via  the  Ethernet  cable.  Open 192.168.88.1 in your web  browser. Username isadmin  and  there  is  no  password. In case IP connection is not available, Winbox can be used to connect to theMAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button ofthe device when starting it until the LED light turns off, and device will start to look for Netinstall servers.Extension Slots and PortsOne 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you canuse either straight or cross-over cables for connecting to other network devices. One Integrated Wireless 5GHz 802.11a/n, 2x2 MIMO with built in grid antenna, max gain 26dBiButtons and JumpersRouterBOOT reset button (RESET, front panel) has three functions:•Hold  this  button  during  boot  time  until  LED  light  starts  flashing,  release  the  button  to  resetRouterOS configuration (total 5 seconds)•Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds)•Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds)Operating System SupportCurrently tested operating system is MikroTik RouterOS starting from version v6.30See www.routerboard.com for more information. Contact support@mikrotik.com 10-Dec-15
Copyright and Warranty informationCopyright  MikroTikls  SIA.  This  document  contains  information  protected  by  copyright  law.  No  part  of  it  may  bereproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarksappearing in this document are the property of their respective holders.Hardware. MikroTik  warrants  all  RouterBOARD  series  equipment  for  the  term  of  twelve  (12)  months  from  theshipping date to be free of defects in materials and workmanship under normal use and service, except in case ofdamage caused by mechanical, electrical or other accidental or intended damages caused by improper use or dueto wind, rain, fire or other acts of nature.To  return  failed  units  to  MikroTik,  you  must  perform  the  following  RMA  (Return  Merchandise  Authorization)procedure.  Follow  the  instructions  below  to  save  time,  efforts,  avoid  costs,  and  improve  the  speed  of  the  RMAprocess.1. If  you  have  purchased  your  product  from  a  MikroTik  Reseller,  please  contact  the  Reseller  companyregarding  all  warranty  and  repair  issues,  the  following  instructions  apply  ONLY  if  you  purchased  yourequipment directly from MikroTik in Latvia.2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:CCR1016-12G,  CCR1016-12G-BU,  CCR1036-12G-4S,  RB1100,  RB1100AH,  RB1100AHx2,  RB1200,RB600, RB600A and RB800 as a paid service (fees apply).3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the senderat sender's cost. If the customer has not organized return of such rejected devices within 12 months fromthe day of arrival, MikroTik has the right to discard them. RMA Instructions are located on our webpage here: http://rma.mikrotik.comThis document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,the  implied  warranty  of  merchantability  and  fitness  for  a  particular  purpose.  The  manufacturer  has  made  everyeffort to ensure the accuracy of the contents of this document, however, it is possible that it may contain technicalinaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, norfor direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including,but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com 10-Dec-15
Federal Communication Commission Interference Statement (FCC ID: TV7LHG5ND )This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital  device,pursuant  to Part  15  of the FCC  Rules. These limits  are designed to provide  reasonable  protectionagainst harmful interference in a residential installation.This  equipment  generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.This  device  and  its  antenna  must  not  be  co-located  or  operation  in  conjunction  with  any  other  antenna  ortransmitter. IMPORTANT: Exposure to Radio Frequency Radiation.2 cm minimum distance has to be maintained between the antenna and the occupational user and 5 cm togeneral public. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolledenvironment can be satisfied.Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennasin the United States (or where FCC rules apply); only those antennas certified with the product are used. The useof any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47part 15.204. The installer should configure the output power level of antennas, according to country regulations andper  antenna  type.  Professional  installation  is  required  of  equipment  with  connectors  to  ensure  compliance  withhealth and safety issues. Industry Canada (IC: 7442A-LHG5ND)This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this devicemay not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of thedevice.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoriséeaux deux conditions suivantes : (1)  l'appareil ne doit pas produire de brouillage, et (2)  l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.See www.routerboard.com for more information. Contact support@mikrotik.com 10-Dec-15
CE Declaration of ConformityFull Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/       !"#$%&'()$ # *%#*##+"'*,---./.01!2!) 3 456789:;78   <;=>5?@?5 A;  !" ; B 6C87B;767B@; 6C6 6C:;67B;4@7; @D@6=B54@9 @ <?EF@7;G?@>8H@I@?5DG8?;<J@45K@?;=7@B5,---./.010L0M N$#%#O)PQ !"%R)PMSTU%#Q*T*O%VU)OS)#*$W,---./.1""     TX * +Y )  !"#*#*XT*# Y* *T*T'*,---./.Z1"2$ $ T[      2[  !"  \'$$) $  ) +#) ) ][!'$$),---./.2^1# [#*T$  !"**)T'*,---./.\%__)P$)T'*)*PT#[122T `abcdefghijfhkfbfjkaifjbcjlcmndaohbo  !"ji``hgpndabfoeghjbojhijonlaojfefobcjaojkfobojmhoeajjqabokajlofbfraojbcjhlcsofj,---./.ak% t#  %    ()   !" )$% # # ()#   # u *  "'*,---./.01 0#  %     ()#  !" v #+#$  ()' M    %#M# %''w*,---./.01x* O#TyT !""Tz*,---./.{'TP|$%}|$)'$#zP$#T)$$1) ~)#T)#PTO !"''T$)T*$)T,---./.!"T*#)# )    MM TP' #   !" N%)• €M• PU' M %*‚ Tƒ*$•T • $S ,---./.S*$S#M#„*#T#M…TM•T1") P *T     #   !"  #*$$  $  '†     *%€*P,---./.21tt# PM$   T)P ‡  !" P M# M MM$ &$$  $ &ˆ‰&$ %##&$"T&,---./.01tt#)) )#()# !")$%#()##)%#*_*"'*,---./.01#$ t%MŠŠ%)  !"‹#+#$)ŒŒ•)%*%'"'*,---./.011#*T Ž$#*)PQ !"%•RMST•%#Q*T*OT%U)O•)#*$,---./.1#* MP*PP !"*T)M*$M*$)$*$##•T'*,---./.1ZZ *T))„[„[  !"%%#T'*,---./.‘#*'$)P[T#T*T'*$)#P$)T1& Härmed intygar MIKROTĪKLS SIA att denna RouterBOARD är i överensstämmelse med de väsentliga egenskapskrav och övrigarelevanta bestämmelser som framgår av direktiv 1999/5/EG.#& TX* !"$*$)T*#Y**T*T'*,---./.Z1EN.  Instruction  manual: Connect  the  power  adapter  to  turn  on  the  device.  Open  192.168.88.1  in  your  web  browser,  to  configure  it.  More  information  onhttp://wiki.mikrotik.com  BG. Инструкция:Свържете адаптера  на  захранване,  за  да  включите устройството. Отворете 192.168.88.1 в  уеб  браузър,  за  данастроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použití: Připojte napájecí adaptér k zapnutí přístroje. Otevřete 192.168.88.1 vewebovém  prohlížeči pro  konfiguraci produktu. Více  informací  najdete  v  http://wiki.mikrotik.com  DK. Instruktionsbog:  Tilslut strømadapteren for  at  tænde forenheden.Åbn 192.168.88.1 i en webbrowser til at  konfigurere produktet.Mere  information i  http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateurd'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com DE.Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren.Weitere  Informationen  im  http://wiki.mikrotik.com  EE.  Kasutusjuhend:  Ühendage toiteadapter seadme  sisselülitamiseks.Avatud 192.168.88.1 in veebilehitsejaseadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de  instrucciones:  Conecte el adaptador de alimentación para encender la unidad. Abra192.168.88.1 en  un  navegador web para  configurar el  producto.Más  información  en  http://wiki.mikrotik.com  IT.  Manuale  di  istruzioni:  Collegare l'adattatore dialimentazione  per  accendere l'unità.Aprire 192.168.88.1 in  un  browser  Web per  configurare  il  prodotto.Maggiori  informazioni in  http://wiki.mikrotik.com  LV.Lietošanas  instrukcija:  Pievienojiet  Strāvas adapteri,  lai  ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta  pārlūku,  lai  konfigurētu produktu. Plašāka informācijahttp://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterį įjunkite įrenginį.Į interneto naršyklę 192.168.88.1 Atidarykite galite konfigūruotigaminį.Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használati utasítás:Csatlakoztassa a hálózati adaptert a készülék bekapcsolásához.Megnyitása192.168.88.1 egy webböngészőben beállítani a terméket. Több információ http://wiki.mikrotik.com NL. Handleiding: Sluit voedingsadapter aan op het apparaat in teschakelen.Open 192.168.88.1 in een  webbrowser  om het product  te  configureren.Meer  informatie  in  http://wiki.mikrotik.com  PL.  Instrukcja  obsługi:Podłączadapter zasilania,  aby  włączyć urządzenie. Otwórz 192.168.88.1 w  przeglądarce  internetowej,  a b y skonfigurować  urządzenie.Więcej  informacji  whttp://wiki.mikrotik.com PT. Manual de instruções:Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web paraconfigurar  o  produto.Mais  informações em  http://wiki.mikrotik.com RO. Instrucțiuni  de  utilizare :  Conectați adaptorul  de alimentare  pentru  a  porni aparatul.Deschide 192.168.88.1 într-un browser web pentru a configura produsul.Mai multe informații în http://wiki.mikrotik.com SK. Návod na použitie:Pripojte napájacíadaptér k zapnutiu prístroja. Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wiki.mikrotik.com SI. Navodila:Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Več informacij v http://wiki.mikrotik.com FI. Käyttöohje: Kytkevirtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisää tietoa http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för attslå  på  enheten.Öppna 192.168.88.1 i en  webbläsare för  att konfigurera  produkten.Mer information på  http://wiki.mikrotik.com   NO. Bruksanvisningen:  Koblestrømadapteren for  å  slå  på enheten. Åpne 192.168.88.1 i en nettleser for  å konfigurere  produktet.Mer informasjon  på  http://wiki.mikrotik.com  GR. εγχειρίδιοοδηγιών:Συνδέστε  τον  προσαρμογέα τροφοδοσίας  για  να  ενεργοποιήσετε τη  μονάδα.Ανοίξτε 192.168.88.1 σε  ένα  πρόγραμμα  περιήγησης στο  Web  για  ναδιαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com 10-Dec-15

Navigation menu