Mikrotikls SIA METAL9HPN DIGITAL TRANSMISSION SYSTEM User Manual

Mikrotikls SIA DIGITAL TRANSMISSION SYSTEM Users Manual

Users Manual

RouterBOARD Metal 9HPNQuick Setup Guide and Warranty InformationThe RouterBOARD Metal 9HPN is a solid, waterproof outdoor device with a high power wirelesstransmitter (900MHz, 802.11b/g/n, N-Male antenna connector), and one 10/100 Ethernet connectorwhich supports MDI-X auto detection. The device is packaged with a 24V power adapter, a PoEinjector and two mounting loops. First use1. Connect the antenna to the N-Male connector2. Use the latches to open the product case, to reveal the Ethernet connector3. Use the provided round rubber insulator to put on the Ethernet cable, and push it into thecase opening, so that the opening is tightly closed. To put the cable though the insulator, you have to put in the cable first, and only thenclamp on the Ethernet connector. If the connector is already on the cable, you can cut theinsulator on one side, to clamp it around the cable, but this sacrifices waterproofness. 4. The Metal accepts 12-28V Passive PoE from a PoE injector (please compensate voltage forloss due to cable length) 5. The default IP address from Ether1 is 192.168.88.1 for configurationUsername is admin and there is no password6. Depending on the antenna used, you must set its gain in the RouterOS software to ensurethat EIRP meets the limit set by authorities. This is done in the Wireless menu. PoweringThe board accepts powering from the Ethernet port (Passive PoE):•Ethernet port accepts passive Power over Ethernet 12-28V DC. Package contains a 24Vadapter and a PoE injector.Maximum power consumption of the device is 12W at 24V.Booting processConnect to wireless SSID “MikroTik” and open 192.168.88.1 in your web browser. Username isadmin and there is no password. In case IP connection is not available, Winbox can be used toconnect to the MAC address of the device. More information here:http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to boot the device from network, for example to use MikroTik Netinstall, hold theRESET button of the device when starting it until the LED light turns off, and Metal will start to lookfor Netinstall servers.MountingTo tighten the Metal to a pole, use the provided mounting loops. The Metal comes bundled with twoplastic and two metallic mounting loops (choose either) - guide the loops around the Metal thoughthe provided edge markings, and around the pole where it will be mounted. You should avoidconnecting a loose Ethernet cable to the Ethernet port - secure the cable to a wall or the pole, sothat the cable weight is not pulling the port. It is recommended to secure the Ethernet cable lessthan 2m from the Metal device. This is to ensure that the cable doesn't damage the port by itsweight, or doesn't fall out. Expansion Slots and Ports•Built in 900MHz 802.11b/g/n wireless, 1x1 MIMO, station mode (AP mode for MetalA-2SHPN)•One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use eitherstraight or cross-over cable for connecting to other network devices. The Ethernet port accepts 8-30V DC poweringfrom a passive PoE injector.See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14
Buttons and Jumpers•RouterOS reset jumper hole (no direct access, board has to be removed from case) – resets RouterOS software todefaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Holdscrewdriver in place until RouterOS configuration is cleared. •RouterBOOT reset button (access through the door) has two functions:oHold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (same result as with reset hole)oHold this button during boot time longer, until LED turns off, then release it to make the device look for Netinstall servers.Operating System SupportCurrently tested operating system is MikroTik RouterOS (starting from version v5.16).Copyright and TrademarksCopyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be reproduced ortransmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOTand MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are theproperty of their respective holders.Hardware. MikroTik warrants all RouterBOARD series equipment for the term of one year from the shipping date to be freeof defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical,electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature.To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Followthe instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process.1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding allwarranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly fromMikroTik in Latvia.2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000, RB1100and RB1200.3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the sender atsender's cost.RMA Instructions are located on our webpage here: http://rma.mikrotik.comManual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort toensure the accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies,typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect,incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of dataor profits. Please report any inaccuracies found to support@mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14
Federal Communication Commission Interference Statement (FCC ID: TV7METL9HPN)This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by oneof the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.•Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.This device and its antenna must not be co-located or operation in conjunction with any otherantenna or transmitter.IMPORTANT: Exposure to Radio Frequency Radiation.63 cm minimum distance has to be maintained between the antenna and the occupational user and142 cm to general public. Under such configuration, the FCC radiation exposure limits set forth foran population/uncontrolled environment can be satisfied.Approved antenna:•Yagi antenna, Model RFY-0900-17B, 17 dBiAntenna Installation. WARNING: It is installer's responsibility to ensure that when using theauthorized antennas in the United States (or where FCC rules apply); only those antennas certifiedwith the product are used. The use of any antenna other than those certified with the product isexpressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure theoutput power level of antennas, according to country regulations and per antenna type. Professionalinstallation is required of equipment with connectors to ensure compliance with health and safetyissues. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14
CE Declaration of ConformityFull Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/[EN] English Hereby, MIKROTĪKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements andother relevant provisions of Directive 1999/5/EC.[BG] Bulgarian С настоящето, MIKROTĪKLS SIA декларира, че ROUTERBOARD е в съответствие със същественитеизисквания и другитеприложими разпоредби на Директива 1999/5/EC.[CZ] Czech MIKROTĪKLS SIA tímto prohlašuje, že ROUTERBOARD splňuje základní požadavky a všechna příslušná ustanoveniSměrnice 1999/5/ES.[DK] Danish Undertegnede MIKROTĪKLS SIA erklærer herved, at følgende udstyr ROUTERBOARD overholder de væsentlige kravog øvrige relevante krav i direktiv 1999/5/EF.[DE] German Hiermit erklärt MIKROTĪKLS SIA dass sich das Gerät ROUTERBOARD in Übereinstimmung mit den grundlegendenAnforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG be`ndet.[EE] Estonian Käesolevaga kinnitab MIKROTĪKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/EÜ põhinõuetele janimetatud direktiivist tulenevatele teistele asjakohastele sätetele.[GR] Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ MIKROTĪKLS SIA ΔΗΛΩΝΕΙ ΟΤΙ ROUTERBOARD ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ[ES] Spanish Por la presente, MIKROTĪKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otrasexigencias relevantes de la Directiva 1999/5/EC.[IT] Italian Con la presente MIKROTĪKLS SIA dichiara che questo ROUTERBOARD è conforme ai requisiti essenziali ed alle altredisposizioni pertinenti stabilite dalla direttiva 1999/5/CE.[LV] Latvian Ar šo MIKROTĪKLS SIA deklarē, ka ROUTERBOARD atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar tosaistītajiem noteikumiem.[LT] Lithuanian Šiuo MIKROTĪKLS SIA deklaruoja, kad šis ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EBDirektyvos nuostatas[HU] Hungarian A MIKROTĪKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD típusú beren-dezés teljesíti az alapvetőkövetelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.[NL] Dutch Hierbij verklaart MIKROTĪKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentiële eisenen de andere relevante bepalin-gen van richtlijn 1999/5/EG.[PL] Polish Niniejszym MIKROTĪKLS SIA deklaruje że ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymiwłaściwymi postanowieniami Dyrektywy 1999/5/EC.[PT] Portuguese Eu, MIKROTĪKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provisões relevantesda Directiva 1999/5/EC.[RO] Romanian Prin prezenta, MIKROTĪKLS SIA declară că aparatul ROUTERBOARD este în conformitate cu cerinţele esenţiale şi cualte prevederi pertinente ale Directivei 1999/5/CE..[SK] Slovak MIKROTĪKLS SIA týmto vyhlasuje, že ROUTERBOARD spĺňa základné požiadavky a všetky príslušné ustanoveniaSmernice 1999/5/ES.[SI] Slovenian MIKROTĪKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi določilidirektive 1999/5/ES.[FI] Finish MIKROTĪKLS SIA vakuuttaa täten että ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellistenvaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.[SE] Swedish Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i direktiv1999/5/EC.[NO] Norwegian MIKROTĪKLS SIA Erklærer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og øvrige relevantekrav i direktiv 1999/5/EF.BG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.88.1 в уеббраузър, за да настроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použití: Připojte napájecíadaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete vhttp://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.1 i enwebbrowser til at konfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectezl'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit.Plus d'informations dans http://wiki.mikrotik.com DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Geräteinzuschalten. Öffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen imhttp://wiki.mikrotik.com EE. Kasutusjuhend: Ühendage toiteadapter seadme sisselülitamiseks. Avatud 192.168.88.1 inveebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones: Conecte eladaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto.Más información en http://wiki.mikrotik.com IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità. Aprire 192.168.88.1 in un browserWeb per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com LV. Lietošanas instrukcija: PievienojietStrāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu. Plašāka informācijahttp://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterį įjunkite įrenginį. Į interneto naršyklę192.168.88.1 Atidarykite galite konfigūruoti gaminį. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használatiutasítás: Csatlakoztassa a hálózati adaptert a készülék bekapcsolásához. Megnyitása 192.168.88.1 egy webböngészőbenbeállítani a terméket. Több információ http://wiki.mikrotik.com NL. Handleiding: Sluit voedingsadapter aan op het apparaatin te schakelen. Open 192.168.88.1 in een webbrowser om het product te configureren. Meer informatie inhttp://wiki.mikrotik.com PL. Instrukcja obsługi: Podłącz adapter zasilania, aby włączyć urządzenie. Otwórz 192.168.88.1 wSee www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14
przeglądarce internetowej, aby skonfigurować urządzenie. Więcej informacji w http://wiki.mikrotik.com PT. Manual deinstruções: Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web paraconfigurar o produto. Mais informações em http://wiki.mikrotik.com RO. Instruc iuni de utilizareț : Conecta iț adaptorul dealimentare pentru a porni aparatul. Deschide 192.168.88.1 într-un browser web pentru a configura produsul. Mai multeinforma iiț în http://wiki.mikrotik.com SK. Návod na použitie: Pripojte napájací adaptér k zapnutiu prístroja. Otvorte192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wiki.mikrotik.com SI.Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Večinformacij v http://wiki.mikrotik.com FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimenmäärittää tuotteen. Lisää tietoa http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för att slå påenheten. Öppna 192.168.88.1 i en webbläsare för att konfigurera produkten. Mer information på http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne 192.168.88.1 i en nettleser for å konfigurereproduktet. Mer informasjon på http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τον προσαρμογέα τροφοδοσίαςγια να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για να διαμορφώσετε τοπροϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14

Navigation menu