Mikrotikls SIA METAL9HPN DIGITAL TRANSMISSION SYSTEM User Manual

Mikrotikls SIA DIGITAL TRANSMISSION SYSTEM Users Manual

a href="https://usermanual.wiki/Mikrotikls-SIA" itemprop="url"> Mikrotikls SIA >

Users Manual

RouterBOARD Metal 9HPNQuick Setup Guide and Warranty InformationThe RouterBOARD Metal 9HPN is a solid, waterproof outdoor device with a high power wirelesstransmitter (900MHz, 802.11b/g/n, N-Male antenna connector), and one 10/100 Ethernet connectorwhich supports MDI-X auto detection. The device is packaged with a 24V power adapter, a PoEinjector and two mounting loops. First use1. Connect the antenna to the N-Male connector2. Use the latches to open the product case, to reveal the Ethernet connector3. Use the provided round rubber insulator to put on the Ethernet cable, and push it into thecase opening, so that the opening is tightly closed. To put the cable though the insulator, you have to put in the cable first, and only thenclamp on the Ethernet connector. If the connector is already on the cable, you can cut theinsulator on one side, to clamp it around the cable, but this sacrifices waterproofness. 4. The Metal accepts 12-28V Passive PoE from a PoE injector (please compensate voltage forloss due to cable length) 5. The default IP address from Ether1 is 192.168.88.1 for configurationUsername is admin and there is no password6. Depending on the antenna used, you must set its gain in the RouterOS software to ensurethat EIRP meets the limit set by authorities. This is done in the Wireless menu. PoweringThe board accepts powering from the Ethernet port (Passive PoE):•Ethernet port accepts passive Power over Ethernet 12-28V DC. Package contains a 24Vadapter and a PoE injector.Maximum power consumption of the device is 12W at 24V.Booting processConnect to wireless SSID “MikroTik” and open 192.168.88.1 in your web browser. Username isadmin and there is no password. In case IP connection is not available, Winbox can be used toconnect to the MAC address of the device. More information here:http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to boot the device from network, for example to use MikroTik Netinstall, hold theRESET button of the device when starting it until the LED light turns off, and Metal will start to lookfor Netinstall servers.MountingTo tighten the Metal to a pole, use the provided mounting loops. The Metal comes bundled with twoplastic and two metallic mounting loops (choose either) - guide the loops around the Metal thoughthe provided edge markings, and around the pole where it will be mounted. You should avoidconnecting a loose Ethernet cable to the Ethernet port - secure the cable to a wall or the pole, sothat the cable weight is not pulling the port. It is recommended to secure the Ethernet cable lessthan 2m from the Metal device. This is to ensure that the cable doesn't damage the port by itsweight, or doesn't fall out. Expansion Slots and Ports•Built in 900MHz 802.11b/g/n wireless, 1x1 MIMO, station mode (AP mode for MetalA-2SHPN)•One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use eitherstraight or cross-over cable for connecting to other network devices. The Ethernet port accepts 8-30V DC poweringfrom a passive PoE injector.See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14
Buttons and Jumpers•RouterOS reset jumper hole (no direct access, board has to be removed from case) – resets RouterOS software todefaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Holdscrewdriver in place until RouterOS configuration is cleared. •RouterBOOT reset button (access through the door) has two functions:oHold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (same result as with reset hole)oHold this button during boot time longer, until LED turns off, then release it to make the device look for Netinstall servers.Operating System SupportCurrently tested operating system is MikroTik RouterOS (starting from version v5.16).Copyright and TrademarksCopyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be reproduced ortransmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOTand MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are theproperty of their respective holders.Hardware. MikroTik warrants all RouterBOARD series equipment for the term of one year from the shipping date to be freeof defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical,electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature.To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Followthe instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process.1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding allwarranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly fromMikroTik in Latvia.2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000, RB1100and RB1200.3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the sender atsender's cost.RMA Instructions are located on our webpage here: http://rma.mikrotik.comManual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort toensure the accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies,typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect,incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of dataor profits. Please report any inaccuracies found to support@mikrotik.comSee www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14
Download:
Mirror Download [FCC.gov]
Document ID2249418
Application IDajK1DGjVaH7XmZNrfip4DA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.99kB (212346 bits)
Date Submitted2014-04-23 00:00:00
Date Available2014-06-07 00:00:00
Creation Date2014-04-03 16:44:27
Producing SoftwareLibreOffice 4.1
Document Lastmod0000-00-00 00:00:00
Document TitleUsers Manual
Document CreatorWriter
Document Author: Normis
FCC ID Filing: TV7METAL9HPN

Navigation menu